Commit ff803ed4 authored by Courtney Cavin's avatar Courtney Cavin Committed by Dmitry Torokhov

Input: add driver for Sharp gp2ap002a00f proximity sensor

This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.
Reviewed-by: default avatarDatta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: default avatarCourtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: default avatarOskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: default avatarDmitry Torokhov <dtor@mail.ru>
parent aeec0517
......@@ -179,6 +179,17 @@ config INPUT_APANEL
To compile this driver as a module, choose M here: the module will
be called apanel.
config INPUT_GP2A
tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
depends on I2C
depends on GENERIC_GPIO
help
Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called gp2ap002a00f.
config INPUT_GPIO_TILT_POLLED
tristate "Polled GPIO tilt switch"
depends on GENERIC_GPIO
......
......@@ -22,8 +22,9 @@ obj-$(CONFIG_INPUT_CMA3000) += cma3000_d0x.o
obj-$(CONFIG_INPUT_CMA3000_I2C) += cma3000_d0x_i2c.o
obj-$(CONFIG_INPUT_COBALT_BTNS) += cobalt_btns.o
obj-$(CONFIG_INPUT_DM355EVM) += dm355evm_keys.o
obj-$(CONFIG_HP_SDC_RTC) += hp_sdc_rtc.o
obj-$(CONFIG_INPUT_GP2A) += gp2ap002a00f.o
obj-$(CONFIG_INPUT_GPIO_TILT_POLLED) += gpio_tilt_polled.o
obj-$(CONFIG_HP_SDC_RTC) += hp_sdc_rtc.o
obj-$(CONFIG_INPUT_IXP4XX_BEEPER) += ixp4xx-beeper.o
obj-$(CONFIG_INPUT_KEYSPAN_REMOTE) += keyspan_remote.o
obj-$(CONFIG_INPUT_KXTJ9) += kxtj9.o
......
/*
* Copyright (C) 2011 Sony Ericsson Mobile Communications Inc.
*
* Author: Courtney Cavin <courtney.cavin@sonyericsson.com>
* Prepared for up-stream by: Oskar Andero <oskar.andero@sonyericsson.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2, as
* published by the Free Software Foundation.
*/
#include <linux/i2c.h>
#include <linux/irq.h>
#include <linux/slab.h>
#include <linux/input.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/input/gp2ap002a00f.h>
struct gp2a_data {
struct input_dev *input;
const struct gp2a_platform_data *pdata;
struct i2c_client *i2c_client;
};
enum gp2a_addr {
GP2A_ADDR_PROX = 0x0,
GP2A_ADDR_GAIN = 0x1,
GP2A_ADDR_HYS = 0x2,
GP2A_ADDR_CYCLE = 0x3,
GP2A_ADDR_OPMOD = 0x4,
GP2A_ADDR_CON = 0x6
};
enum gp2a_controls {
/* Software Shutdown control: 0 = shutdown, 1 = normal operation */
GP2A_CTRL_SSD = 0x01
};
static int gp2a_report(struct gp2a_data *dt)
{
int vo = gpio_get_value(dt->pdata->vout_gpio);
input_report_switch(dt->input, SW_FRONT_PROXIMITY, !vo);
input_sync(dt->input);
return 0;
}
static irqreturn_t gp2a_irq(int irq, void *handle)
{
struct gp2a_data *dt = handle;
gp2a_report(dt);
return IRQ_HANDLED;
}
static int gp2a_enable(struct gp2a_data *dt)
{
return i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_OPMOD,
GP2A_CTRL_SSD);
}
static int gp2a_disable(struct gp2a_data *dt)
{
return i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_OPMOD,
0x00);
}
static int gp2a_device_open(struct input_dev *dev)
{
struct gp2a_data *dt = input_get_drvdata(dev);
int error;
error = gp2a_enable(dt);
if (error < 0) {
dev_err(&dt->i2c_client->dev,
"unable to activate, err %d\n", error);
return error;
}
gp2a_report(dt);
return 0;
}
static void gp2a_device_close(struct input_dev *dev)
{
struct gp2a_data *dt = input_get_drvdata(dev);
int error;
error = gp2a_disable(dt);
if (error < 0)
dev_err(&dt->i2c_client->dev,
"unable to deactivate, err %d\n", error);
}
static int __devinit gp2a_initialize(struct gp2a_data *dt)
{
int error;
error = i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_GAIN,
0x08);
if (error < 0)
return error;
error = i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_HYS,
0xc2);
if (error < 0)
return error;
error = i2c_smbus_write_byte_data(dt->i2c_client, GP2A_ADDR_CYCLE,
0x04);
if (error < 0)
return error;
error = gp2a_disable(dt);
return error;
}
static int __devinit gp2a_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
const struct gp2a_platform_data *pdata = client->dev.platform_data;
struct gp2a_data *dt;
int error;
if (!pdata)
return -EINVAL;
if (pdata->hw_setup) {
error = pdata->hw_setup(client);
if (error < 0)
return error;
}
error = gpio_request_one(pdata->vout_gpio, GPIOF_IN, GP2A_I2C_NAME);
if (error)
goto err_hw_shutdown;
dt = kzalloc(sizeof(struct gp2a_data), GFP_KERNEL);
if (!dt) {
error = -ENOMEM;
goto err_free_gpio;
}
dt->pdata = pdata;
dt->i2c_client = client;
error = gp2a_initialize(dt);
if (error < 0)
goto err_free_mem;
dt->input = input_allocate_device();
if (!dt->input) {
error = -ENOMEM;
goto err_free_mem;
}
input_set_drvdata(dt->input, dt);
dt->input->open = gp2a_device_open;
dt->input->close = gp2a_device_close;
dt->input->name = GP2A_I2C_NAME;
dt->input->id.bustype = BUS_I2C;
dt->input->dev.parent = &client->dev;
input_set_capability(dt->input, EV_SW, SW_FRONT_PROXIMITY);
error = request_threaded_irq(client->irq, NULL, gp2a_irq,
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
IRQF_ONESHOT,
GP2A_I2C_NAME, dt);
if (error) {
dev_err(&client->dev, "irq request failed\n");
goto err_free_input_dev;
}
error = input_register_device(dt->input);
if (error) {
dev_err(&client->dev, "device registration failed\n");
goto err_free_irq;
}
device_init_wakeup(&client->dev, pdata->wakeup);
i2c_set_clientdata(client, dt);
return 0;
err_free_irq:
free_irq(client->irq, dt);
err_free_input_dev:
input_free_device(dt->input);
err_free_mem:
kfree(dt);
err_free_gpio:
gpio_free(pdata->vout_gpio);
err_hw_shutdown:
if (pdata->hw_shutdown)
pdata->hw_shutdown(client);
return error;
}
static int __devexit gp2a_remove(struct i2c_client *client)
{
struct gp2a_data *dt = i2c_get_clientdata(client);
const struct gp2a_platform_data *pdata = dt->pdata;
device_init_wakeup(&client->dev, false);
free_irq(client->irq, dt);
input_unregister_device(dt->input);
kfree(dt);
gpio_free(pdata->vout_gpio);
if (pdata->hw_shutdown)
pdata->hw_shutdown(client);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int gp2a_suspend(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct gp2a_data *dt = i2c_get_clientdata(client);
int retval = 0;
if (device_may_wakeup(&client->dev)) {
enable_irq_wake(client->irq);
} else {
mutex_lock(&dt->input->mutex);
if (dt->input->users)
retval = gp2a_disable(dt);
mutex_unlock(&dt->input->mutex);
}
return retval;
}
static int gp2a_resume(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct gp2a_data *dt = i2c_get_clientdata(client);
int retval = 0;
if (device_may_wakeup(&client->dev)) {
disable_irq_wake(client->irq);
} else {
mutex_lock(&dt->input->mutex);
if (dt->input->users)
retval = gp2a_enable(dt);
mutex_unlock(&dt->input->mutex);
}
return retval;
}
#endif
static SIMPLE_DEV_PM_OPS(gp2a_pm, gp2a_suspend, gp2a_resume);
static const struct i2c_device_id gp2a_i2c_id[] = {
{ GP2A_I2C_NAME, 0 },
{ }
};
static struct i2c_driver gp2a_i2c_driver = {
.driver = {
.name = GP2A_I2C_NAME,
.owner = THIS_MODULE,
.pm = &gp2a_pm,
},
.probe = gp2a_probe,
.remove = __devexit_p(gp2a_remove),
.id_table = gp2a_i2c_id,
};
static int __init gp2a_init(void)
{
return i2c_add_driver(&gp2a_i2c_driver);
}
static void __exit gp2a_exit(void)
{
i2c_del_driver(&gp2a_i2c_driver);
}
module_init(gp2a_init);
module_exit(gp2a_exit);
MODULE_AUTHOR("Courtney Cavin <courtney.cavin@sonyericsson.com>");
MODULE_DESCRIPTION("Sharp GP2AP002A00F I2C Proximity/Opto sensor driver");
MODULE_LICENSE("GPL v2");
#ifndef _GP2AP002A00F_H_
#define _GP2AP002A00F_H_
#include <linux/i2c.h>
#define GP2A_I2C_NAME "gp2ap002a00f"
/**
* struct gp2a_platform_data - Sharp gp2ap002a00f proximity platform data
* @vout_gpio: The gpio connected to the object detected pin (VOUT)
* @wakeup: Set to true if the proximity can wake the device from suspend
* @hw_setup: Callback for setting up hardware such as gpios and vregs
* @hw_shutdown: Callback for properly shutting down hardware
*/
struct gp2a_platform_data {
int vout_gpio;
bool wakeup;
int (*hw_setup)(struct i2c_client *client);
int (*hw_shutdown)(struct i2c_client *client);
};
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment