- 16 Jan, 2015 40 commits
-
-
Jens Axboe authored
commit a33c1ba2 upstream. We currently use num_possible_cpus(), but that breaks on sparc64 where the CPU ID space is discontig. Use nr_cpu_ids as the highest CPU ID instead, so we don't end up reading from invalid memory. Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joerg Roedel authored
commit 62c22167 upstream. Since commit 1196c2fb a domain is only destroyed in the notifier path if it is hot-unplugged. This caused a domain leakage in iommu_attach_device when a driver was unbound from the device and bound to VFIO. In this case the device is attached to a new domain and unlinked from the old domain. At this point nothing points to the old domain anymore and its memory is leaked. Fix this by explicitly freeing the old domain in iommu_attach_domain. Fixes: 1196c2fb (iommu/vt-d: Fix dmar_domain leak in iommu_attach_device) Tested-by:
Jerry Hoemann <jerry.hoemann@hp.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Jiang Liu authored
commit cc4f14aa upstream. There's an off-by-one bug in function __domain_mapping(), which may trigger the BUG_ON(nr_pages < lvl_pages) when (nr_pages + 1) & superpage_mask == 0 The issue was introduced by commit 9051aa02 "intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()", which sets sg_res to "nr_pages + 1" to avoid some of the 'sg_res==0' code paths. It's safe to remove extra "+1" because sg_res is only used to calculate page size now. Reported-And-Tested-by:
Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by:
Jiang Liu <jiang.liu@linux.intel.com> Acked-By:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Richard Weinberger authored
commit aa5ad3b6 upstream. If the erase worker is unable to erase a PEB it will free the ubi_wl_entry itself. The failing ubi_wl_entry must not free()'d again after do_sync_erase() returns. Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
-
Richard Weinberger authored
commit f38aed97 upstream. The logic of vfree()'ing vol->upd_buf is tied to vol->updating. In ubi_start_update() vol->updating is set long before vmalloc()'ing vol->upd_buf. If we encounter a write failure in ubi_start_update() before vmalloc() the UBI device release function will try to vfree() vol->upd_buf because vol->updating is set. Fix this by allocating vol->upd_buf directly after setting vol->updating. Fixes: [ 31.559338] UBI warning: vol_cdev_release: update of volume 2 not finished, volume is damaged [ 31.559340] ------------[ cut here ]------------ [ 31.559343] WARNING: CPU: 1 PID: 2747 at mm/vmalloc.c:1446 __vunmap+0xe3/0x110() [ 31.559344] Trying to vfree() nonexistent vm area (ffffc90001f2b000) [ 31.559345] Modules linked in: [ 31.565620] 0000000000000bba ffff88002a0cbdb0 ffffffff818f0497 ffff88003b9ba148 [ 31.566347] ffff88002a0cbde0 ffffffff8156f515 ffff88003b9ba148 0000000000000bba [ 31.567073] 0000000000000000 0000000000000000 ffff88002a0cbe88 ffffffff8156c10a [ 31.567793] Call Trace: [ 31.568034] [<ffffffff818f0497>] dump_stack+0x4e/0x7a [ 31.568510] [<ffffffff8156f515>] ubi_io_write_vid_hdr+0x155/0x160 [ 31.569084] [<ffffffff8156c10a>] ubi_eba_write_leb+0x23a/0x870 [ 31.569628] [<ffffffff81569b36>] vol_cdev_write+0x226/0x380 [ 31.570155] [<ffffffff81179265>] vfs_write+0xb5/0x1f0 [ 31.570627] [<ffffffff81179f8a>] SyS_pwrite64+0x6a/0xa0 [ 31.571123] [<ffffffff818fde12>] system_call_fastpath+0x16/0x1b Signed-off-by:
-
Tony Lindgren authored
commit 027bc8b0 upstream. On some ARMs the memory can be mapped pgprot_noncached() and still be working for atomic operations. As pointed out by Colin Cross <ccross@android.com>, in some cases you do want to use pgprot_noncached() if the SoC supports it to see a debug printk just before a write hanging the system. On ARMs, the atomic operations on strongly ordered memory are implementation defined. So let's provide an optional kernel parameter for configuring pgprot_noncached(), and use pgprot_writecombine() by default. Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robherring2@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Anton Vorontsov <anton@enomsg.org> Cc: Colin Cross <ccross@android.com> Cc: Olof Johansson <olof@lixom.net> Cc: Russell King <linux@arm.linux.org.uk> Acked-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
-
Rob Herring authored
commit 7ae9cb81 upstream. Currently trying to use pstore on at least ARMs can hang as we're mapping the peristent RAM with pgprot_noncached(). On ARMs, pgprot_noncached() will actually make the memory strongly ordered, and as the atomic operations pstore uses are implementation defined for strongly ordered memory, they may not work. So basically atomic operations have undefined behavior on ARM for device or strongly ordered memory types. Let's fix the issue by using write-combine variants for mappings. This corresponds to normal, non-cacheable memory on ARM. For many other architectures, this change does not change the mapping type as by default we have: #define pgprot_writecombine pgprot_noncached The reason why pgprot_noncached() was originaly used for pstore is because Colin Cross <ccross@android.com> had observed lost debug prints right before a device hanging write operation on some systems. For the platforms supporting pgprot_noncached(), we can add a an optional configuration option to support that. But let's get pstore working first before adding new features. Cc: Arnd Bergmann <arnd@arndb.de> Cc: Anton Vorontsov <cbouatmailru@gmail.com> Cc: Colin Cross <ccross@android.com> Cc: Olof Johansson <olof@lixom.net> Cc: linux-kernel@vger.kernel.org Acked-by:
Rob Herring <rob.herring@calxeda.com> [tony@atomide.com: updated description] Signed-off-by:
-
Hante Meuleman authored
commit 94a61208 upstream. The ifidx provided by FW needs to be offsetted when receiving data packets. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Myron Stowe authored
commit 36e81648 upstream. Commit 6ac665c6 ("PCI: rewrite PCI BAR reading code") masked off low-order bits from 'l', but not from 'sz'. Both are passed to pci_size(), which compares 'base == maxbase' to check for read-only BARs. The masking of 'l' means that comparison will never be 'true', so the check for read-only BARs no longer works. Resolve this by also masking off the low-order bits of 'sz' before passing it into pci_size() as 'maxbase'. With this change, pci_size() will once again catch the problems that have been encountered to date: - AGP aperture BAR of AMD-7xx host bridges: if the AGP window is disabled, this BAR is read-only and read as 0x00000008 [1] - BARs 0-4 of ALi IDE controllers can be non-zero and read-only [1] - Intel Sandy Bridge - Thermal Management Controller [8086:0103]; BAR 0 returning 0xfed98004 [2] - Intel Xeon E5 v3/Core i7 Power Control Unit [8086:2fc0]; Bar 0 returning 0x00001a [3] Link: [1] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/drivers/pci/probe.c?id=1307ef6621991f1c4bc3cec1b5a4ebd6fd3d66b9 ("PCI: probing read-only BARs" (pre-git)) Link: [2] https://bugzilla.kernel.org/show_bug.cgi?id=43331 Link: [3] https://bugzilla.kernel.org/show_bug.cgi?id=85991Reported-by:
William Unruh <unruh@physics.ubc.ca> Reported-by:
Martin Lucina <martin@lucina.net> Signed-off-by:
Myron Stowe <myron.stowe@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Matthew Wilcox <willy@linux.intel.com> Signed-off-by:
-
Johan Hedberg authored
commit 6a8fc95c upstream. When connectable mode is enabled (page scan on) through some non-mgmt method the HCI_CONNECTABLE flag will not be set. For backwards compatibility with user space versions not using mgmt we should not require HCI_CONNECTABLE to be set if HCI_MGMT is not set. Reported-by:
Pali Rohár <pali.rohar@gmail.com> Tested-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Marcel Holtmann authored
commit 8bfe8442 upstream. When controllers set the HCI_QUIRK_INVALID_BDADDR flag, it is required by userspace to program a valid public Bluetooth device address into the controller before it can be used. After successful address configuration, the internal state changes and the controller runs the complete initialization procedure. However one small difference is that this is no longer the HCI_SETUP stage. The HCI_SETUP stage is only valid during initial controller setup. In this case the stack runs the initialization as part of the HCI_CONFIG stage. The controller version information, default name and supported commands are only stored during HCI_SETUP. While these information are static, they are not read initially when HCI_QUIRK_INVALID_BDADDR is set. So when running in HCI_CONFIG state, these information need to be updated as well. This especially impacts Bluetooth 4.1 and later controllers using extended feature pages and second event mask page. Signed-off-by:
-
Marcel Holtmann authored
commit a4d5504d upstream. The internal representation of the LE white list needs to be cleared when receiving a successful HCI_Reset command. A reset of the controller is expected to start with an empty LE white list. When the LE white list is not cleared on controller reset, the passive background scanning might skip programming the remote devices. Only changes to the LE white list are programmed when passive background is started. Signed-off-by:
-
Johan Hedberg authored
commit 0b1db38c upstream. These days we allow simultaneous LE scanning and advertising. Checking for whether advertising is enabled or not is therefore not a reliable way to determine whether directed advertising was used to trigger the connection creation. The appropriate place to check (instead of the hdev context) is the connection role that's stored in the hci_conn. This patch fixes such a check in le_conn_timeout() which could otherwise lead to incorrect HCI commands being sent. Signed-off-by:
-
Johan Hedberg authored
commit 980ffc0a upstream. The le_conn_timeout() may call hci_le_conn_failed() which in turn may call hci_conn_del(). Trying to use the _sync variant for cancelling the conn timeout from hci_conn_del() could therefore result in a deadlock. This patch converts hci_conn_del() to use the non-sync variant so the deadlock is not possible. Signed-off-by:
-
Alexander Aring authored
commit b0c42cd7 upstream. This patch reverts commit: a7807d73 ("Bluetooth: 6lowpan: Avoid memory leak if memory allocation fails") which was wrong suggested by Alexander Aring. The function skb_unshare run also kfree_skb on failure. Signed-off-by:
Alexander Aring <alex.aring@gmail.com> Signed-off-by:
-
Dmitry Tunin authored
commit 3bb30a7c upstream. Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This Bluetooth module requires loading patch and sysconfig by ath3k driver. T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3408 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
-
Richard Guy Briggs authored
commit 63f13448 upstream. Since both ppc and ppc64 have LE variants which are now reported by uname, add that flag (__AUDIT_ARCH_LE) to syscall_get_arch() and add AUDIT_ARCH_PPC64LE variant. Without this, perf trace and auditctl fail. Mainline kernel reports ppc64le (per a0588015) but there is no matching AUDIT_ARCH_PPC64LE. Since 32-bit PPC LE is not supported by audit, don't advertise it in AUDIT_ARCH_PPC* variants. See: https://www.redhat.com/archives/linux-audit/2014-August/msg00082.html https://www.redhat.com/archives/linux-audit/2014-December/msg00004.htmlSigned-off-by:
Richard Guy Briggs <rgb@redhat.com> Acked-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
sukadev@linux.vnet.ibm.com authored
commit f34b6c72 upstream. The 24x7 counters are continuously running and not updated on an interrupt. So we record the event counts when stopping the event or deleting it. But to "read" a single counter in 24x7, we allocate a page and pass it into the hypervisor (The HV returns the page full of counters from which we extract the specific counter for this event). We allocate a page using GFP_USER and when deleting the event, we end up with the following warning because we are blocking in interrupt context. [ 698.641709] BUG: scheduling while atomic: swapper/0/0/0x10010000 We could use GFP_ATOMIC but that could result in failures. Pre-allocate a buffer so we don't have to allocate in interrupt context. Further as Michael Ellerman suggested, use Per-CPU buffer so we only need to allocate once per CPU. Signed-off-by:
Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Signed-off-by:
-
Paul Mackerras authored
commit 8117ac6a upstream. Currently, when going idle, we set the flag indicating that we are in nap mode (paca->kvm_hstate.hwthread_state) and then execute the nap (or sleep or rvwinkle) instruction, all with the MMU on. This is bad for two reasons: (a) the architecture specifies that those instructions must be executed with the MMU off, and in fact with only the SF, HV, ME and possibly RI bits set, and (b) this introduces a race, because as soon as we set the flag, another thread can switch the MMU to a guest context. If the race is lost, this thread will typically start looping on relocation-on ISIs at 0xc...4400. This fixes it by setting the MSR as required by the architecture before setting the flag or executing the nap/sleep/rvwinkle instruction. [ shreyas@linux.vnet.ibm.com: Edited to handle LE ] Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by:
-
Mahesh Salgaonkar authored
commit 682e77c8 upstream. The existing MCE code calls flush_tlb hook with IS=0 (single page) resulting in partial invalidation of TLBs which is not right. This patch fixes that by passing IS=0xc00 to invalidate whole TLB for successful recovery from TLB and ERAT errors. Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
-
Anton Blanchard authored
commit cd32e2dc upstream. We have some code in udbg_uart_getc_poll() that tries to protect against a NULL udbg_uart_in, but gets it all wrong. Found with the LLVM static analyzer (scan-build). Fixes: 30925748 ("powerpc: Cleanup udbg_16550 and add support for LPC PIO-only UARTs") Signed-off-by:
Anton Blanchard <anton@samba.org> [mpe: Add some newlines for readability while we're here] Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 9972fc0b upstream. Commit 6071c22e "ktest: Rewrite the config-bisect to actually work" fixed the config-bisect to work nicely but in doing so it broke make_min_config by changing the way assign_configs works. The assign_configs function now adds the config to the hash even if it is disabled, but changes the hash value to be that of the line "# CONFIG_FOO is not set". Unfortunately, the make_min_config test only checks to see if the config is removed. It now needs to check if the config is in the hash and not set to be disabled. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Andrew Jackson authored
commit 3475c3d0 upstream. Flush the FIFOs when the stream is prepared for use. This avoids an inadvertent swapping of the left/right channels if the FIFOs are not empty at startup. Signed-off-by:
Andrew Jackson <Andrew.Jackson@arm.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Peter Rosin authored
commit 681a1956 upstream. When the codec is connected using i2c, it will only auto-increment register addresses if msb (0x80) of the register address byte is set. [Fixes cache sync if multiple adjacent registers are updated -- broonie] Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
-
Jyri Sarha authored
commit bbc686b3 upstream. Fix off by one read beyond the end of a table. Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Jyri Sarha <jsarha@ti.com> Signed-off-by:
-
Jarkko Nikula authored
commit 48826ee5 upstream. Commit 5fe5b767 ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets") revealed ill-defined control in a route between "STENL Mux" and DACs in max98090.c: max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR Since there is no control between "STENL Mux" and DACs the control name must be NULL not "NULL". Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit 50c0f21b upstream. Make sure to check the version field of the firmware header to make sure to not accidentally try to parse a firmware file with a different layout. Trying to do so can result in loading invalid firmware code to the device. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Takashi Iwai authored
commit 077661b6 upstream. The of_node_put() call in eukrea_tlv320_probe() may take an uninitialized pointer, as compiler spotted out: sound/soc/fsl/eukrea-tlv320.c:221:14: warning: 'ssi_np' may be used uninitialized in this function [-Wuninitialized] This patch adds the proper NULL initializations as a fix. (codec_np is also NULL initialized just for consistency.) Fixes: 66f23290 ('ASoC: eukrea-tlv320: Add DT support') Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Felix Fietkau authored
commit 9e4982f6 upstream. Like with ath9k, ath5k queues also need to be ordered by priority. queue_info->tqi_subtype already contains the correct index, so use it instead of relying on the order of ath5k_hw_setup_tx_queue calls. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Emmanuel Grumbach authored
commit 55fd1ce8 upstream. A few device IDs were added, reflect this change in the driver. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit b4c82adc upstream. Interoperability issues were identified and root caused to the Smart Fifo watermarks. These issues arose with NetGear R7000. Fix this. Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support") Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 5a12a07e upstream. Since the commit below, iwldvm sends the FLUSH command to the firmware. All the devices that use iwldvm have a firmware that expects the _v3 version of this command, besides 5150. 5150's latest available firmware still expects a _v2 version of the FLUSH command. This means that since the commit below, we had a mismatch for this specific device only. This mismatch led to the NMI below: Loaded firmware version: 8.24.2.2 Start IWL Error Log Dump: Status: 0x0000004C, count: 5 0x00000004 | NMI_INTERRUPT_WDG 0x000006F4 | uPc 0x000005BA | branchlink1 0x000006F8 | branchlink2 0x000008C2 | interruptlink1 0x00005B02 | interruptlink2 0x00000002 | data1 0x07030000 | data2 0x00000068 | line 0x3E80510C | beacon time 0x728A0EF4 | tsf low 0x0000002A | tsf hi 0x00000000 | time gp1 0x01BDC977 | time gp2 0x00000000 | time gp3 0x00010818 | uCode version 0x00000000 | hw version 0x00484704 | board version 0x00000002 | hcmd 0x2FF23080 | isr0 0x0103E000 | isr1 0x0000001A | isr2 0x1443FCC3 | isr3 0x11800112 | isr4 0x00000068 | isr_pref 0x000000D4 | wait_event 0x00000000 | l2p_control 0x00000007 | l2p_duration 0x00103040 | l2p_mhvalid 0x00000007 | l2p_addr_match 0x00000000 | lmpm_pmg_sel 0x00000000 | timestamp 0x00000200 | flow_handler This was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=88961 Fixes: a0855054 ("iwlwifi: dvm: drop non VO frames when flushing") Signed-off-by:
-
Stefano Stabellini authored
commit 2c3fc8d2 upstream. Need to pass the pointer within the swiotlb internal buffer to the swiotlb library, that in the case of xen_unmap_single is dev_addr, not paddr. Signed-off-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Acked-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Stefano Stabellini authored
commit 9490c6c6 upstream. In xen_swiotlb_sync_single we always call xen_dma_sync_single_for_cpu, even when we should call xen_dma_sync_single_for_device. Fix that. Signed-off-by:
-
Stefano Stabellini authored
commit c884227e upstream. On x86 truncation cannot occur because config XEN depends on X86_64 || (X86_32 && X86_PAE). On ARM truncation can occur without CONFIG_ARM_LPAE, when the dma operation involves foreign grants. However in that case the physical address returned by xen_bus_to_phys is actually invalid (there is no mfn to pfn tracking for foreign grants on ARM) and it is not used. Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Acked-by:
-
Stefano Stabellini authored
commit d6883e6f upstream. xen_dma_unmap_page and xen_dma_sync_single_for_cpu take a dma_addr_t handle as argument, not a physical address. Signed-off-by:
-
Stephane Grosjean authored
commit dc50ddcd upstream. This patchs fixes a misplaced call to memset() that fills the request buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT requests, the content set by the caller was thus lost. With this patch, the memory area is zeroed only when requesting info from the device. Signed-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Stephane Grosjean authored
commit af35d0f1 upstream. This patch sets the correct reverse sequence order to the instructions set to run, when any failure occurs during the initialization steps. It also adds the missing unregistration call of the can device if the failure appears after having been registered. Signed-off-by:
-
Felix Fietkau authored
commit 78063d81 upstream. Hardware queues are ordered by priority. Use queue index 0 for BK, which has lower priority than BE. Signed-off-by:
-
Felix Fietkau authored
commit ad8fdccf upstream. The driver passes the desired hardware queue index for a WMM data queue in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which instead relied on the order in which the function is called. Reported-by:
Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by:
-
