- 12 Feb, 2019 40 commits
-
-
Lenny Szubowicz authored
[ Upstream commit 98cff8b2 ] In __ghes_panic() clear the block status in the APEI generic error status block for that generic hardware error source before calling panic() to prevent a second panic() in the crash kernel for exactly the same fatal error. Otherwise ghes_probe(), running in the crash kernel, would see an unhandled error in the APEI generic error status block and panic again, thereby precluding any crash dump. Signed-off-by:
Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by:
David Arcari <darcari@redhat.com> Tested-by:
Tyler Baicar <baicar.tyler@gmail.com> Acked-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Kai-Heng Feng authored
[ Upstream commit 1fb3a7a7 ] I210 ethernet card doesn't wakeup when a cable gets plugged. It's because its PME is not set. Since commit 42eca230 ("PCI: Don't touch card regs after runtime suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops calling pci_finish_runtime_suspend(), which enables the PCI PME. To fix the issue, let's not to save PCI states when it's runtime suspend, to let the PCI subsystem enables PME. Fixes: 42eca230 ("PCI: Don't touch card regs after runtime suspend D3") Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Young Xiao authored
[ Upstream commit eec90376 ] If ice driver has q_vectors w/ active NAPI that has no rings, then this will result in a divide by zero error. To correct it I am updating the driver code so that we only support NAPI on q_vectors that have 1 or more rings allocated to them. See commit 13a8cd19 ("i40e: Do not enable NAPI on q_vectors that have no rings") for detail. Signed-off-by:
Young Xiao <YangX92@hotmail.com> Acked-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Konstantin Khorenko authored
[ Upstream commit 31389b53 ] Out of bound read reported by KASan. i40iw_net_event() reads unconditionally 16 bytes from neigh->primary_key while the memory allocated for "neighbour" struct is evaluated in neigh_alloc() as tbl->entry_size + dev->neigh_priv_len where "dev" is a net_device. But the driver does not setup dev->neigh_priv_len and we read beyond the neigh entry allocated memory, so the patch in the next mail fixes this. Signed-off-by:
Konstantin Khorenko <khorenko@virtuozzo.com> Tested-by:
-
Peter Rosin authored
[ Upstream commit f75df8d4 ] Blitting an image with "negative" offsets is not working since there is no clipping. It hopefully just crashes. For the bootup logo, there is protection so that blitting does not happen as the image is drawn further and further to the right (ROTATE_UR) or further and further down (ROTATE_CW). There is however no protection when drawing in the opposite directions (ROTATE_UD and ROTATE_CCW). Add back this protection. The regression is 20-odd years old but the mindless warning-killing mentality displayed in commit 34bdb666 ("fbdev: fbmem: remove positive test on unsigned values") is also to blame, methinks. Fixes: 448d4797 ("fbdev: fb_do_show_logo() updates") Signed-off-by:
Peter Rosin <peda@axentia.se> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Fabian Frederick <ffrederick@users.sourceforge.net> Cc: Geert Uytterhoeven <geert+renesas@glider.be> cc: Geoff Levand <geoff@infradead.org> Cc: James Simmons <jsimmons@users.sf.net> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Guoqing Jiang authored
[ Upstream commit e820d55c ] When both regular IO and resync IO happen at the same time, and if we also need to split regular. Then we can see tasks hang due to barrier. 1. resync thread [ 1463.757205] INFO: task md1_resync:5215 blocked for more than 480 seconds. [ 1463.757207] Not tainted 4.19.5-1-default #1 [ 1463.757209] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1463.757212] md1_resync D 0 5215 2 0x80000000 [ 1463.757216] Call Trace: [ 1463.757223] ? __schedule+0x29a/0x880 [ 1463.757231] ? raise_barrier+0x8d/0x140 [raid10] [ 1463.757236] schedule+0x78/0x110 [ 1463.757243] raise_barrier+0x8d/0x140 [raid10] [ 1463.757248] ? wait_woken+0x80/0x80 [ 1463.757257] raid10_sync_request+0x1f6/0x1e30 [raid10] [ 1463.757265] ? _raw_spin_unlock_irq+0x22/0x40 [ 1463.757284] ? is_mddev_idle+0x125/0x137 [md_mod] [ 1463.757302] md_do_sync.cold.78+0x404/0x969 [md_mod] [ 1463.757311] ? wait_woken+0x80/0x80 [ 1463.757336] ? md_rdev_init+0xb0/0xb0 [md_mod] [ 1463.757351] md_thread+0xe9/0x140 [md_mod] [ 1463.757358] ? _raw_spin_unlock_irqrestore+0x2e/0x60 [ 1463.757364] ? __kthread_parkme+0x4c/0x70 [ 1463.757369] kthread+0x112/0x130 [ 1463.757374] ? kthread_create_worker_on_cpu+0x40/0x40 [ 1463.757380] ret_from_fork+0x3a/0x50 2. regular IO [ 1463.760679] INFO: task kworker/0:8:5367 blocked for more than 480 seconds. [ 1463.760683] Not tainted 4.19.5-1-default #1 [ 1463.760684] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1463.760687] kworker/0:8 D 0 5367 2 0x80000000 [ 1463.760718] Workqueue: md submit_flushes [md_mod] [ 1463.760721] Call Trace: [ 1463.760731] ? __schedule+0x29a/0x880 [ 1463.760741] ? wait_barrier+0xdd/0x170 [raid10] [ 1463.760746] schedule+0x78/0x110 [ 1463.760753] wait_barrier+0xdd/0x170 [raid10] [ 1463.760761] ? wait_woken+0x80/0x80 [ 1463.760768] raid10_write_request+0xf2/0x900 [raid10] [ 1463.760774] ? wait_woken+0x80/0x80 [ 1463.760778] ? mempool_alloc+0x55/0x160 [ 1463.760795] ? md_write_start+0xa9/0x270 [md_mod] [ 1463.760801] ? try_to_wake_up+0x44/0x470 [ 1463.760810] raid10_make_request+0xc1/0x120 [raid10] [ 1463.760816] ? wait_woken+0x80/0x80 [ 1463.760831] md_handle_request+0x121/0x190 [md_mod] [ 1463.760851] md_make_request+0x78/0x190 [md_mod] [ 1463.760860] generic_make_request+0x1c6/0x470 [ 1463.760870] raid10_write_request+0x77a/0x900 [raid10] [ 1463.760875] ? wait_woken+0x80/0x80 [ 1463.760879] ? mempool_alloc+0x55/0x160 [ 1463.760895] ? md_write_start+0xa9/0x270 [md_mod] [ 1463.760904] raid10_make_request+0xc1/0x120 [raid10] [ 1463.760910] ? wait_woken+0x80/0x80 [ 1463.760926] md_handle_request+0x121/0x190 [md_mod] [ 1463.760931] ? _raw_spin_unlock_irq+0x22/0x40 [ 1463.760936] ? finish_task_switch+0x74/0x260 [ 1463.760954] submit_flushes+0x21/0x40 [md_mod] So resync io is waiting for regular write io to complete to decrease nr_pending (conf->barrier++ is called before waiting). The regular write io splits another bio after call wait_barrier which call nr_pending++, then the splitted bio would continue with raid10_write_request -> wait_barrier, so the splitted bio has to wait for barrier to be zero, then deadlock happens as follows. resync io regular io raise_barrier wait_barrier generic_make_request wait_barrier To resolve the issue, we need to call allow_barrier to decrease nr_pending before generic_make_request since regular IO is not issued to underlying devices, and wait_barrier is called again to ensure no internal IO happening. Fixes: fc9977dd ("md/raid10: simplify the splitting of requests.") Reported-and-tested-by:
Siniša Bandin <sinisa@4net.rs> Signed-off-by:
Guoqing Jiang <gqjiang@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit fdac7513 ] clps711x_fb_probe() increments refcnt of disp device node by of_parse_phandle() and leaves it undecremented on both successful and error paths. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Wenjing Liu authored
[ Upstream commit 99b922f9 ] [why] Some dongle doesn't have a valid extended dongle caps, but we still set the extended dongle caps to be valid. This causes validation fails for all timing. [how] If no dp_hdmi_max_pixel_clk is provided, don't use extended dongle caps. Signed-off-by:
Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit a52c5a16 ] There are several warnings from Clang about no case statement matching the constant 0: In file included from drivers/block/drbd/drbd_receiver.c:48: In file included from drivers/block/drbd/drbd_int.h:48: In file included from ./include/linux/drbd_genl_api.h:54: In file included from ./include/linux/genl_magic_struct.h:236: ./include/linux/drbd_genl.h:321:1: warning: no case matching constant switch condition '0' GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/genl_magic_struct.h:220:10: note: expanded from macro 'GENL_struct' switch (0) { ^ Silence this warning by adding a 'case 0:' statement. Additionally, adjust the alignment of the statements in the ct_assert_unique macro to avoid a checkpatch warning. This solution was originally sent by Arnd Bergmann with a default case statement: https://lore.kernel.org/patchwork/patch/756723/ Link: https://github.com/ClangBuiltLinux/linux/issues/43Suggested-by:
Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Lars Ellenberg authored
[ Upstream commit 9848b6dd ] If you try to promote a Secondary while connected to a Primary and allow-two-primaries is NOT set, we will wait for "ping-timeout" to give this node a chance to detect a dead primary, in case the cluster manager noticed faster than we did. But if we then are *still* connected to a Primary, we fail (after an additional timeout of ping-timout). This change skips the spurious second timeout. Most people won't notice really, since "ping-timeout" by default is half a second. But in some installations, ping-timeout may be 10 or 20 seconds or more, and spuriously delaying the error return becomes annoying. Signed-off-by:
-
Lars Ellenberg authored
[ Upstream commit b17b5960 ] With "on-no-data-accessible suspend-io", DRBD requires the next attach or connect to be to the very same data generation uuid tag it lost last. If we first lost connection to the peer, then later lost connection to our own disk, we would usually refuse to re-connect to the peer, because it presents the wrong data set. However, if the peer first connects without a disk, and then attached its disk, we accepted that same wrong data set, which would be "unexpected" by any user of that DRBD and cause "undefined results" (read: very likely data corruption). The fix is to forcefully disconnect as soon as we notice that the peer attached to the "wrong" dataset. Signed-off-by:
-
Roland Kammerer authored
[ Upstream commit d29e89e3 ] So far there was the possibility that we called genlmsg_new(GFP_NOIO)/mutex_lock() while holding an rcu_read_lock(). This included cases like: drbd_sync_handshake (acquire the RCU lock) drbd_asb_recover_1p drbd_khelper drbd_bcast_event genlmsg_new(GFP_NOIO) --> may sleep drbd_sync_handshake (acquire the RCU lock) drbd_asb_recover_1p drbd_khelper notify_helper genlmsg_new(GFP_NOIO) --> may sleep drbd_sync_handshake (acquire the RCU lock) drbd_asb_recover_1p drbd_khelper notify_helper mutex_lock --> may sleep While using GFP_ATOMIC whould have been possible in the first two cases, the real fix is to narrow the rcu_read_lock. Reported-by:
Jia-Ju Bai <baijiaju1990@163.com> Reviewed-by:
Roland Kammerer <roland.kammerer@linbit.com> Signed-off-by:
-
Miroslav Lichvar authored
[ Upstream commit 5d867836 ] The timecounter needs to be updated at least once in half of the cyclecounter interval to prevent timecounter_cyc2time() interpreting a new timestamp as an old value and causing a backward jump. This would be an issue if the timecounter multiplier was so small that the update interval would not be limited by the 64-bit overflow in multiplication. Shorten the calculated interval to make sure the timecounter is updated in time even when the system clock is slowed down by up to 10%, the multiplier is increased by up to 10%, and the scheduled overflow check is late by 15%. Cc: Richard Cochran <richardcochran@gmail.com> Cc: Ariel Levkovich <lariel@mellanox.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Alexey Kardashevskiy authored
[ Upstream commit bdbf649e ] The powernv platform maintains 2 TCE tables for VFIO - a hardware TCE table and a table with userspace addresses; the latter is used for marking pages dirty when corresponging TCEs are unmapped from the hardware table. a68bd126 ("powerpc/powernv/ioda: Allocate indirect TCE levels on demand") enabled on-demand allocation of the hardware table, however it missed the other table so it has still been fully allocated at the boot time. This fixes the issue by allocating a single level, just like we do for the hardware table. Fixes: a68bd126 ("powerpc/powernv/ioda: Allocate indirect TCE levels on demand") Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Naftali Goldstein authored
[ Upstream commit 189b8d44 ] The FW expects to get the ppe value for each NSS-BW pair in the same format as in the he phy capabilities IE, which means that a value of 0 implies ppe should be used for BPSK (mcs 0). If there are no PPE thresholds in the IE, or if for some NSS-RU pair there's no threshold set for it (this could happen because it's a variable-sized field), it means no PPE should not be used for that pair, so the value sent to FW should be 7 which corresponds to "none". Fixes: 514c3069 ("iwlwifi: add support for IEEE802.11ax") Signed-off-by:
Naftali Goldstein <naftali.goldstein@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Madhavan Srinivasan authored
[ Upstream commit 17cfccc9 ] MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value. Thresholding counter can be used to count latency cycles such as load miss to reload. But threshold counter value is not relevant when the sampled instruction type is unknown or reserved. Patch to fix the thresholding counter value to zero when sampled instruction type is unknown or reserved. Fixes: 170a315f('powerpc/perf: Support to export MMCRA[TEC*] field to userspace') Signed-off-by:
Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by:
-
Jian Shen authored
[ Upstream commit 75edb610 ] Each pf supports max 64 vectors and 128 tqps. For 2p/4p core scenario, there may be more than 64 cpus online. So the result of min_t(u16, num_Online_cpus(), tqp_num) may be more than 64. This patch adds check for the vector number. Fixes: dd38c726 ("net: hns3: fix for coalesce configuration lost during reset") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit 4f68ef64 ] The function cw1200_bss_info_changed() and cw1200_hw_scan() can be concurrently executed. The two functions both access a possible shared variable "frame.skb". This shared variable is freed by dev_kfree_skb() in cw1200_upload_beacon(), which is called by cw1200_bss_info_changed(). The free operation is protected by a mutex lock "priv->conf_mutex" in cw1200_bss_info_changed(). In cw1200_hw_scan(), this shared variable is accessed without the protection of the mutex lock "priv->conf_mutex". Thus, concurrency use-after-free bugs may occur. To fix these bugs, the original calls to mutex_lock(&priv->conf_mutex) and mutex_unlock(&priv->conf_mutex) are moved to the places, which can protect the accesses to the shared variable. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
-
Mahesh Rajashekhara authored
[ Upstream commit 65111785 ] Problem: - during the driver initialization, driver will poll fw for KERNEL_UP in a 30 seconds timeout. - if the firmware is not ready after 30 seconds, driver will not be loaded. Fix: - change timeout from 30 seconds to 3 minutes. Reported-by:
Feng Li <lifeng1519@gmail.com> Reviewed-by:
Ajish Koshy <ajish.koshy@microsemi.com> Reviewed-by:
Murthy Bhat <Murthy.Bhat@microsemi.com> Reviewed-by:
Dave Carroll <david.carroll@microsemi.com> Reviewed-by:
Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by:
Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Signed-off-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Dave Carroll authored
[ Upstream commit 7ff44499 ] - fix race condition when a unit is deleted after an RLL, and before we have gotten the LV_STATUS page of the unit. - In this case we will get a standard inquiry, rather than the desired page. This will result in a unit presented which no longer exists. - If we ask for LV_STATUS, insure we get LV_STATUS Reviewed-by:
Scott Teel <scott.teel@microsemi.com> Reviewed-by:
-
Mahesh Rajashekhara authored
[ Upstream commit b2346b50 ] Reviewed-by:
Scott Benesh <scott.benesh@microsemi.com> Reviewed-by:
-
Ido Schimmel authored
[ Upstream commit be2d6f42 ] When a LAG device or a VLAN device on top of it is enslaved to a bridge, the driver propagates the CHANGEUPPER event to the LAG's slaves. This causes each physical port to increase the reference count of the internal representation of the bridge port by calling mlxsw_sp_port_bridge_join(). However, when a port is removed from a LAG, the corresponding leave() function is not called and the reference count is not decremented. This leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that try to understand if the bridge port should be destroyed even when its reference count is not 0. Instead, make sure that when a port is unlinked from a LAG it would see the same events as if the LAG (or its uppers) were unlinked from a bridge. The above is achieved by walking the LAG's uppers when a port is unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is enslaved to a bridge. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Reviewed-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit fa89a459 ] gcc warn this: net/ipv6/xfrm6_tunnel.c:143 __xfrm6_tunnel_alloc_spi() warn: always true condition '(spi <= 4294967295) => (0-u32max <= u32max)' 'spi' is u32, which always not greater than XFRM6_TUNNEL_SPI_MAX because of wrap around. So the second forloop will never reach. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit efc38dd7 ] Due to the alignment handling, it actually matters where in the code we add the 4 bytes for the presence bitmap to the length; the first field is the timestamp with 8 byte alignment so we need to add the space for the extra vendor namespace presence bitmap *before* we do any alignment for the fields. Move the presence bitmap length accounting to the right place to fix the alignment for the data properly. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Christophe Leroy authored
[ Upstream commit 05a4ab82 ] With the following piece of code, the following compilation warning is encountered: if (_IOC_DIR(ioc) != _IOC_NONE) { int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ; if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) { drivers/platform/test/dev.c: In function 'my_ioctl': drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable] int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ; This patch fixes it by referencing 'type' in the macro allthough doing nothing with it. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Eric Yang authored
[ Upstream commit 12750d16 ] [Why] YCbCr420 packing format uses two chanels for luma, and 1 channel for both chroma component. Our previous implementation did not account for this and results in every other pixel having very high luma value, showing greyish color instead of black. YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> ..... YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> ..... [How] Program the second channel with the black color value for luma as well. Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Reviewed-by:
Hugo Hu <Hugo.Hu@amd.com> Acked-by:
-
Chen-Yu Tsai authored
[ Upstream commit 28ac03b9 ] On some systems that actually have the bluetooth controller wired up with an extra clock signal, it's possible the bluetooth controller probes before the clock provider. clk_get would return a defer probe error, which was not handled by this driver. Handle this properly, so that these systems can work reliably. Tested-by:
Ondrej Jirman <megous@megous.com> Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Paul Hsieh authored
[ Upstream commit bd4905a9 ] [WHY] On customer board, there is one pluse (1v , < 1ms) on DDC_CLK pin when plug / unplug DP cable. Driver will read it and config DP to HDMI/DVI dongle. [HOW] If there is a real dongle, DDC_CLK should be always pull high. Try to read again to recovery this special case. Retry times = 3. Need additional 3ms to detect DP passive dongle(3 failures) Signed-off-by:
Paul Hsieh <paul.hsieh@amd.com> Reviewed-by:
-
Huazhong Tan authored
[ Upstream commit ae6017a7 ] In the hns3_nic_uninit_vector_data(), the procedure of uninitializing the tqp_vector's IRQ has not set affinity_notify to NULL and changes its init flag. This patch fixes it. And for simplificaton, local variable tqp_vector is used instead of priv->tqp_vector[i]. Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC") Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Dennis Zhou authored
[ Upstream commit 6ab7d47b ] From Michael Cree: "Bisection lead to commit b38d08f3 ("percpu: restructure locking") as being the cause of lockups at initial boot on the kernel built for generic Alpha. On a suggestion by Tejun Heo that: So, the only thing I can think of is that it's calling spin_unlock_irq() while irq handling isn't set up yet. Can you please try the followings? 1. Convert all spin_[un]lock_irq() to spin_lock_irqsave/unlock_irqrestore()." Fixes: b38d08f3 ("percpu: restructure locking") Reported-and-tested-by:
Michael Cree <mcree@orcon.net.nz> Acked-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Dennis Zhou <dennis@kernel.org> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit 866053bb ] To avoid this warning: CC /tmp/build/perf/util/s390-cpumsf.o util/s390-cpumsf.c: In function 's390_cpumsf_samples': util/s390-cpumsf.c:508:3: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'off_t' [-Wformat=] pr_err("[%#08" PRIx64 "] Invalid AUX trailer entry TOD clock base\n", ^ Now the various Android cross toolchains used in the perf tools container test builds are all clean and we can remove this: export EXTRA_MAKE_ARGS="WERROR=0" Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Thomas Richter <tmricht@linux.ibm.com> Link: https://lkml.kernel.org/n/tip-5rav4ccyb0sjciysz2i4p3sx@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit 0afcf29b ] Reducing this noise when cross building to the Android NDK: util/header.c: In function 'perf_header__fprintf_info': util/header.c:2710:45: warning: pointer targets in passing argument 1 of 'ctime' differ in signedness [-Wpointer-sign] fprintf(fp, "# captured on : %s", ctime(&st.st_ctime)); ^ In file included from util/../perf.h:5:0, from util/evlist.h:11, from util/header.c:22: /opt/android-ndk-r15c/platforms/android-26/arch-arm/usr/include/time.h:81:14: note: expected 'const time_t *' but argument is of type 'long unsigned int *' extern char* ctime(const time_t*) __LIBC_ABI_PUBLIC__; ^ Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-6bz74zp080yhmtiwb36enso9@git.kernel.orgSigned-off-by:
-
Bin Liu authored
[ Upstream commit 54578ee8 ] Since the runtime PM support was added in musb, dsps relies on the timer calling otg_timer() to activate the usb subsystem. However the driver doesn't enable the timer for peripheral port, then the peripheral port is unable to be enumerated by a host if the other usb port is disabled or in peripheral mode too. So let's start the timer for peripheral port too. Fixes: ea2f35c0 ("usb: musb: Fix sleeping function called from invalid context for hdrc glue") Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Bin Liu authored
[ Upstream commit 6010abf2 ] Due to lack of ID pin interrupt event on AM335x devices, the musb dsps driver uses polling to detect usb device attach for dual-role port. But in the case if a micro-A cable adapter is attached without a USB device attached to the cable, the musb state machine gets stuck in a_wait_vrise state waiting for the MUSB_CONNECT interrupt which won't happen due to the usb device is not attached. The state is stuck in a_wait_vrise even after the micro-A cable is detached, which could cause VBUS retention if then the dual-role port is attached to a host port. To fix the problem, make a_wait_vrise as a transient state, then move the state to either a_wait_bcon for host port or a_idle state for dual-role port, if no usb device is attached to the port. Signed-off-by:
-
Mark Rutland authored
[ Upstream commit 0d640732 ] When we emulate an MMIO instruction, we advance the CPU state within decode_hsr(), before emulating the instruction effects. Having this logic in decode_hsr() is opaque, and advancing the state before emulation is problematic. It gets in the way of applying consistent single-step logic, and it prevents us from being able to fail an MMIO instruction with a synchronous exception. Clean this up by only advancing the CPU state *after* the effects of the instruction are emulated. Cc: Peter Maydell <peter.maydell@linaro.org> Reviewed-by:
Alex Bennée <alex.bennee@linaro.org> Reviewed-by:
Christoffer Dall <christoffer.dall@arm.com> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit 5f30b2e8 ] kzalloc() return should always be checked - notably in example code where this may be seen as reference. On failure of allocation in livepatch_fix1_dummy_alloc() respectively dummy_alloc() previous allocation is freed (thanks to Petr Mladek <pmladek@suse.com> for catching this) and NULL returned. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Fixes: 439e7271 ("livepatch: introduce shadow variable API") Acked-by:
Joe Lawrence <joe.lawrence@redhat.com> Reviewed-by:
Petr Mladek <pmladek@suse.com> Acked-by:
Miroslav Benes <mbenes@suse.cz> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Doug Smythies authored
[ Upstream commit 66354690 ] This script is supposed to be allowed to run with regular user privileges if a previously captured trace is being post processed. Commit fbe31388 (tools/power/x86/intel_pstate_tracer: Free the trace buffer memory) introduced a bug that breaks that option. Commit 35459105 (tools/power/x86/intel_pstate_tracer: Add optional setting of trace buffer memory allocation) moved the code but kept the bug. This patch fixes the issue. Fixes: 35459105 (tools/power/x86/intel_pstate_tracer: Add optional ...) Signed-off-by:
Doug Smythies <dsmythies@telus.net> Signed-off-by:
-
Michael Chan authored
[ Upstream commit 36d65be9 ] When bringing up a device, the code checks to see if the number of MSIX has changed. pci_disable_msix() should be called first before changing the number of reserved NQs/CMPL rings. This ensures that the MSIX vectors associated with the NQs/CMPL rings are still properly mapped when pci_disable_msix() masks the vectors. This patch will prevent errors when RDMA support is added for the new 57500 chips. When the RDMA driver shuts down, the number of NQs is decreased and we must use the new sequence to prevent MSIX errors. Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Fabrizio Castro authored
[ Upstream commit 51243b73 ] Similarly to R-Car E3, RZ/G2E doesn't come with automatic transmission registers, as such it is not considered compatible with the existing fallback bindings. Add SoC specific binding compatibility to allow for later support for automatic transmission. Signed-off-by:
Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit bef0b897 ] The strncpy() function may leave the destination string buffer unterminated, better use strlcpy() that we have a __weak fallback implementation for systems without it. In this case the 'target' buffer is coming from a list of build-ids that are expected to have a len of at most (SBUILD_ID_SIZE - 1) chars, so probably we're safe, but since we're using strncpy() here, use strlcpy() instead to provide the intended safety checking without the using the problematic strncpy() function. This fixes this warning on an Alpine Linux Edge system with gcc 8.2: util/probe-file.c: In function 'probe_cache__open.isra.5': util/probe-file.c:427:3: error: 'strncpy' specified bound 41 equals destination size [-Werror=stringop-truncation] strncpy(sbuildid, target, SBUILD_ID_SIZE); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 1f3736c9 ("perf probe: Show all cached probes") Link: https://lkml.kernel.org/n/tip-l7n8ggc9kl38qtdlouke5yp5@git.kernel.orgSigned-off-by:
-
