We shouldn't need to pass the struct device *dev to enetc CBDR APIs over
and over again, so save this inside struct enetc_cbdr::dma_dev and avoid
calling it from the enetc_free_cbdr functions.

This breaks the dependency of the cbdr API from struct enetc_si (the
station interface).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since there is a dedicated file in this driver for interacting with
control BD rings, it makes sense to move these functions there.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maciej W. Rozycki says:

====================
FDDI: defxx: CSR access fixes and improvements

As a lab upgrade I have recently replaced a dated 32-bit x86 server with
a new POWER9 system.  One of the purposes of the system has been providing
network based resources to clients over my FDDI network.  As such the new
server has also received a new DEFPA FDDI network adapter.

 As it turned out the interface did not work with the driver as shipped by
the most recent stable Debian release (Linux version 5.9.15) for ppc64el.
Symptoms were inconclusive, and the DEFPA adapter turned out to have a
manufacturing defect as well, however eventually I have figured out the
PCIe host bridge used with the system, Power Systems Host Bridge 4 (PHB4),
does not (anymore) implement PCI I/O transactions, while the binary defxx
driver as shipped by Debian comes configured for port I/O, and then a bug
in resource handling causes the driver to try and use an unassigned port
I/O range for adapter's PDQ main ASIC's CSR access.

 Fortunately the PFI PCI interface ASIC used with the DEFPA adapter has
been designed such as to provide for both PCI I/O and PCI memory accesses
to be used for PDQ CSR access, via a pair of BARs to be alternatively
used.

 Originally the defxx driver only supported port I/O access, but in the
course of interfacing it to the TURBOchannel bus I had to implement MMIO
access too, and while at it I have added a kernel configuration option to
globally switch between port I/O and MMIO at compilation time, however
conservatively defaulting to port I/O for EISA bus support where the use
of MMIO currently requires the adapter to have been suitably configured
via ECU (EISA Configuration Utility), supplied externally.

 With the kernel configuration option set to MMIO the DEFPA interface
works correctly with my POWER9 system.  Therefore I have prepared this
small patch series consisting of a pair of conservative bug fixes, to be
backported to stable branches, and then a pair of improvements for the
robustness of the driver.

 So changes 1/4 and 2/4 apply both to net and net-next, and then changes
3/4 and 4/4 apply on top of them to net-next only.  In particular there
are diff context dependencies going like this: 1/4 -> 3/4 -> 4/4.  Let me
know if this submission needs to be sorted differently.

 See individual change descriptions for further details as to the actual
changes made.

 NB the ESIC interface chip used for slave address decoding with the DEFEA
EISA adapter has decoding implemented for address bits 31:10 and therefore
supports full 32-bit range for the allocation of the CSR decoding window.
For DOS compatibility reasons ECU however only allows allocations between
0x000c0000 and 0x000effff.

 Given that for other compatibility reasons EISA is subtractively decoded
on mixed PCI/EISA systems we could allocate an MMIO region from arbitrary
unoccupied memory space and program the ESIC suitably without regard for
that compatibility limitation.  In fact I have a proof-of-concept change
and it seems to work reliably.

 However with these patches applied the driver continues supporting port
I/O as fallback and the EISA product ID register is located in the EISA
slot-specific port I/O address space, so any EISA system however modern
(sounds like a joke, eh?) also has to support port I/O access somehow.

 So while I think such a dynamic MMIO allocation would be an example of
good engineering, but it would require changes to our EISA core and
therefore it may have had sense 25 years ago when EISA was still
mainstream, but not nowadays when EISA systems are I suppose more of a
curiosity rather than the usual equipment.

 This patch series has been thoroughly verified with Linux 5.11.0 as
released and then a Raptor Talos II POWER9 system and a Malta 5Kc MIPS64
system for PCI DEFPA adapter support, an Advanced Integrated Research
486EI x86 system for EISA DEFEA adapter support, and a Digital Equipment
DECstation 5000 model 260 MIPS III system for TURBOchannel DEFTA adapter
support, covering both port I/O and MMIO operation where applicable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace repeated "defxx" strings with a reference to the DRV_NAME macro
and then use the driver's name rather that the bus address with resource
requests so as to have contents of /proc/iomem and /proc/ioports more
meaningful to the user, in line with what drivers usually do.

So rather than say:

5000-50ff : DEC FDDIcontroller/EISA Adapter
  5000-503f : 00:05
  5040-5043 : 00:05
5400-54ff : DEC FDDIcontroller/EISA Adapter
5800-58ff : DEC FDDIcontroller/EISA Adapter
5c00-5cff : DEC FDDIcontroller/EISA Adapter
  5c80-5cbf : 00:05

or:

620c080020000-620c08002007f : 0031:02:04.0
  620c080020000-620c08002007f : 0031:02:04.0
620c080030000-620c08003ffff : 0031:02:04.0

or:

1f100000-1f10003f : tc2

we report:

5000-50ff : DEC FDDIcontroller/EISA Adapter
  5000-503f : defxx
  5040-5043 : defxx
5400-54ff : DEC FDDIcontroller/EISA Adapter
5800-58ff : DEC FDDIcontroller/EISA Adapter
5c00-5cff : DEC FDDIcontroller/EISA Adapter
  5c80-5cbf : defxx

and:

620c080020000-620c08002007f : 0031:02:04.0
  620c080020000-620c08002007f : defxx
620c080030000-620c08003ffff : 0031:02:04.0

and:

1f100000-1f10003f : defxx

respectively for the DEFEA (EISA), DEFPA (PCI), and DEFTA (TURBOchannel)
adapters.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.  Conversely a DEFEA
adapter can have its MMIO decoding disabled with ECU (EISA Configuration
Utility) and therefore not available for us with the resource allocation
infrastructure we implement.

However either I/O address space will always be available for use with
the DEFEA (EISA) and DEFPA (PCI) adapters and both have double address
decoding implemented in hardware for Control and Status Register access.
The two kinds of adapters can be present both at once in a single mixed
PCI/EISA system.  For the DEFTA (TURBOchannel) variant there is no issue
as there has been no port I/O address space defined for that bus.

To make people's life easier and the driver more robust remove the
DEFXX_MMIO configuration option so as to rather than making the choice
for the I/O address space to use at build time for all the adapters
installed in the system let the driver choose the most suitable address
space dynamically on a case-by-case basis at run time.  Make MMIO the
default and resort to port I/O should the default fail for some reason.

This way multiple adapters installed in one system can use different I/O
address spaces each, in particular in the presence of DEFEA adapters in
a pure-EISA or a mixed EISA/PCI system (it is expected that DEFPA boards
will use MMIO in normal circumstances).

The choice of the I/O address space to use continues being reported by
the driver on startup, e.g.:

eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.12 2021/03/10  Lawrence V. Stefani and others
00:05: DEFEA at I/O addr = 0x5000, IRQ = 10, Hardware addr = 00-00-f8-c8-b3-b6
00:05: registered as fddi0

and:

defxx: v1.12 2021/03/10  Lawrence V. Stefani and others
0031:02:04.0: DEFPA at MMIO addr = 0x620c080020000, IRQ = 57, Hardware addr = 00-60-6d-93-91-98
0031:02:04.0: registered as fddi0

and:

defxx: v1.12 2021/03/10  Lawrence V. Stefani and others
tc2: DEFTA at MMIO addr = 0x1f100000, IRQ = 21, Hardware addr = 08-00-2b-b0-8b-1e
tc2: registered as fddi0

so there is no need to add further information.

The change is supposed to cause a negligible performance hit as I/O
accessors will now have code executed conditionally at run time.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.

The default kernel configuration choice for the defxx driver is the use
of I/O ports rather than MMIO for PCI and EISA systems.  It may have
made sense as a conservative backwards compatible choice back when MMIO
operation support was added to the driver as a part of TURBOchannel bus
support.  However nowadays this configuration choice makes the driver
unusable with systems that do not implement I/O transactions for PCIe.

Make DEFXX_MMIO the configuration default then, except where configured
for EISA.  This exception is because an EISA adapter can have its MMIO
decoding disabled with ECU (EISA Configuration Utility) and therefore
not available with the resource allocation infrastructure we implement,
while port I/O is always readily available as it uses slot-specific
addressing, directly mapped to the slot an option card has been placed
in and handled with our EISA bus support core.  Conversely a kernel that
supports modern systems which may not have I/O transactions implemented
for PCIe will usually not be expected to handle legacy EISA systems.

The change of the default will make it easier for people, including but
not limited to distribution packagers, to make a working choice for the
driver.

Update the option description accordingly and while at it replace the
potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports"
according to our nomenclature used elsewhere.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: e89a2cfb ("[TC] defxx: TURBOchannel support")
Cc: stable@vger.kernel.org # v2.6.21+
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.

For those systems the PCI BARs that request a mapping in the I/O space
have the length recorded in the corresponding PCI resource set to zero,
which makes it unassigned:

# lspci -s 0031:02:04.0 -v
0031:02:04.0 FDDI network controller: Digital Equipment Corporation PCI-to-PDQ Interface Chip [PFI] FDDI (DEFPA) (rev 02)
	Subsystem: Digital Equipment Corporation FDDIcontroller/PCI (DEFPA)
	Flags: bus master, medium devsel, latency 136, IRQ 57, NUMA node 8
	Memory at 620c080020000 (32-bit, non-prefetchable) [size=128]
	I/O ports at <unassigned> [disabled]
	Memory at 620c080030000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: defxx
	Kernel modules: defxx

#

Regardless the driver goes ahead and requests it (here observed with a
Raptor Talos II POWER9 system), resulting in an odd /proc/ioport entry:

# cat /proc/ioports
00000000-ffffffffffffffff : 0031:02:04.0
#

Furthermore, the system gets confused as the driver actually continues
and pokes at those locations, causing a flood of messages being output
to the system console by the underlying system firmware, like:

defxx: v1.11 2014/07/01  Lawrence V. Stefani and others
defxx 0031:02:04.0: enabling device (0140 -> 0142)
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010000
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event

and so on and so on (possibly intermixed actually, as there's no locking
between the kernel and the firmware in console port access with this
particular system, but cleaned up above for clarity), and once some 10k
of such pairs of the latter two messages have been produced an interace
eventually shows up in a useless state:

0031:02:04.0: DEFPA at I/O addr = 0x0, IRQ = 57, Hardware addr = 00-00-00-00-00-00

This was not expected to happen as resource handling was added to the
driver a while ago, because it was not known at that time that a PCI
system would be possible that cannot assign port I/O resources, and
oddly enough `request_region' does not fail, which would have caught it.

Correct the problem then by checking for the length of zero for the CSR
resource and bail out gracefully refusing to register an interface if
that turns out to be the case, producing messages like:

defxx: v1.11 2014/07/01  Lawrence V. Stefani and others
0031:02:04.0: Cannot use I/O, no address set, aborting
0031:02:04.0: Recompile driver with "CONFIG_DEFXX_MMIO=y"

Keep the original check for the EISA MMIO resource as implemented,
because in that case the length is hardwired to 0x400 as a consequence
of how the compare/mask address decoding works in the ESIC chip and it
is only the base address that is set to zero if MMIO has been disabled
for the adapter in EISA configuration, which in turn could be a valid
bus address in a legacy-free system implementing PCI, especially for
port I/O.

Where the EISA MMIO resource has been disabled for the adapter in EISA
configuration this arrangement keeps producing messages like:

eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.11 2014/07/01  Lawrence V. Stefani and others
00:05: Cannot use MMIO, no address set, aborting
00:05: Recompile driver with "CONFIG_DEFXX_MMIO=n"
00:05: Or run ECU and set adapter's MMIO location

with the last two lines now swapped for easier handling in the driver.

There is no need to check for and catch the case of a port I/O resource
not having been assigned for EISA as the adapter uses the slot-specific
I/O space, which gets assigned by how EISA has been specified and maps
directly to the particular slot an option card has been placed in.  And
the EISA variant of the adapter has additional registers that are only
accessible via the port I/O space anyway.

While at it factor out the error message calls into helpers and fix an
argument order bug with the `pr_err' call now in `dfx_register_res_err'.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4d0438e5 ("defxx: Clean up DEFEA resource management")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Misc updates

This patch set contains miscellaneous updates for mlxsw.

Patches #1-#2 reword an extack message to make it clearer and fix a
comment.

Patch #3 bumps the minimum firmware version enforced by mlxsw. This is
needed for two upcoming features: Resilient hashing and per-flow
sampling.

Patches #4-#6 improve the information reported via devlink-health for
'fw_fatal' events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MFDE.irisc_id and MFDE.event_id were adjusted according to what is
actually implemented in firmware.

Adjust the shift and size of these fields in mlxsw as well.

Note that the displacement of the first field is not a regression.
It was always incorrect and therefore reported "0".
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the MFDE.log_ip field to devlink health reporter in order to ease
firmware debug. This field encodes the instruction pointer that triggered
the CR space timeout.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend MFDE (Monitoring FW Debug) register with new field specifying the
instruction pointer that triggered the CR space timeout.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The indicated version fixes the following two issues:

- MIRROR_SAMPLER_ACTION.mirror_probability_rate inverted. This has
  implication for per-flow sampling.

- When adjacency is replaced-if-inactive (RATR.opcode=3), bad parameter
  was reported when replacing an active entry. This breaks offload of
  resilient next-hop groups.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The comment did not include the register name.
Add `pmaos` to align the comment with other comments.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'Uppers' is not clear enough for all users when referring to upper
devices.

Reword the error message so it will be clearer.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The series of space has been replaced by tab space
wherever required.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit 29d98f54 ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.

Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the recent update to MAINTAINERS update my e-mail address.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the recent update to MAINTAINERS update my e-mail address.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the recent update to MAINTAINERS update my e-mail address.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement this callback in order to get the offloaded stats added to the
kernel stats.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following coccicheck warning:
./drivers/isdn/mISDN/dsp_core.c:956:6-9: Unneeded variable: "err".
Return "0" on line 1001
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BCM4908 devices have MAC address accessible using NVMEM so it's needed
to use OF helper for reading it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro list uses skb_shinfo(skb)->frag_list to link two skb together,
and NAPI_GRO_CB(p)->last->next is used when there are more skb,
see skb_gro_receive_list(). gso expects that each segmented skb is
linked together using skb->next, so only the first skb->next need
to set to skb_shinfo(skb)-> frag_list when doing gso list segment.

It is the same reason that nskb->next does not need to be set to
list_skb before goto the error handling, because nskb->next already
pointers to list_skb.

And nskb is also the last skb at the end of loop, so remove tail
variable and use nskb instead.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding a couple of break statements instead of
just letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of
letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of
letting the code fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.

Link: https://github.com/KSPP/linux/issues/115Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.

Link: https://github.com/KSPP/linux/issues/115Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://github.com/KSPP/linux/issues/115Signed-off-by: David S. Miller <davem@davemloft.net>

There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].

Refactor the code according to the use of flexible-array members in
smt_sif_operation structure, instead of one-element arrays. Also, make
use of the struct_size() helper instead of the open-coded version
to calculate the size of the struct-with-flex-array. Additionally, make
use of the typeof operator to properly determine the object type to be
passed to macro smtod().

Also, this helps the ongoing efforts to enable -Warray-bounds by fixing
the following warnings:

  CC [M]  drivers/net/fddi/skfp/smt.o
drivers/net/fddi/skfp/smt.c: In function ‘smt_send_sif_operation’:
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */
      |                   ^~~
drivers/net/fddi/skfp/smt.c:1084:30: warning: array subscript 1 is above array bounds of ‘struct smt_p_lem[1]’ [-Warray-bounds]
 1084 |    smt_fill_lem(smc,&sif->lem[i],i) ;
      |                      ~~~~~~~~^~~
In file included from drivers/net/fddi/skfp/h/smc.h:42,
                 from drivers/net/fddi/skfp/smt.c:15:
drivers/net/fddi/skfp/h/smt.h:767:19: note: while referencing ‘lem’
  767 |  struct smt_p_lem lem[1] ; /* phy lem status */

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to assign the msg->msg_name to sin or sin6,
because there is DECLARE_SOCKADDR statement.
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rewriteing -> rewriting
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wheter -> whether
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of queues implemented by many virtio backends is limited,
especially some machines have a large number of CPUs. In this case, it
is often impossible to allocate a separate queue for
XDP_TX/XDP_REDIRECT, then xdp cannot be loaded to work, even xdp does
not use the XDP_TX/XDP_REDIRECT.

This patch allows XDP_TX/XDP_REDIRECT to run by reuse the existing SQ
with __netif_tx_lock() hold when there are not enough queues.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bit mask for MSG_* seems a little confused here. Replace it
with BIT() to make it clear to understand.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf-next 2021-03-09

The following pull-request contains BPF updates for your *net-next* tree.

We've added 90 non-merge commits during the last 17 day(s) which contain
a total of 114 files changed, 5158 insertions(+), 1288 deletions(-).

The main changes are:

1) Faster bpf_redirect_map(), from Björn.

2) skmsg cleanup, from Cong.

3) Support for floating point types in BTF, from Ilya.

4) Documentation for sys_bpf commands, from Joe.

5) Support for sk_lookup in bpf_prog_test_run, form Lorenz.

6) Enable task local storage for tracing programs, from Song.

7) bpf_for_each_map_elem() helper, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>