- 10 Apr, 2015 40 commits
-
-
Himanshu Madhani authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
James Bottomley <JBottomley@Odin.com>
-
Himanshu Madhani authored
o Added message indicating firmware dump was sucessfully collected for ISP27XX. o Improve logging to help debug firmware dump process for ISP27XX. Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Nigel Kirkland authored
Signed-off-by:
Nigel Kirkland <nigel.kirkland@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
[Bart: additional sparse warning caused by this patch] [jejb: fix sparse warning] Signed-off-by:
-
Himanshu Madhani authored
Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
James Smart authored
Update version to 10.5.0.0 for upstream patch set Signed-off-by:
Dick Kennedy <dick.kennedy@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Reviewed-by:
-
James Smart authored
Update copyright to 2015 Signed-off-by:
-
James Smart authored
FCP_CMD payload was not always properly initialized on SLI-3 devices. Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Currently, the driver plays off the fact that older sli4 adapters have a different rpi access pattern that allowed for the rpi reference to be released earlier in the teardown sequence, allowing the driver to recycle the rpi value sooner. Newer sli4 adapters have a different access pattern that requires us to wait for a later mailbox completion. This changes the put call location on the newer sli4 adapters. Symptoms of the error are "0110 ELS" and the "0372 iotag" errors. Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Fix host reset escalation killing all IOs. SLI-3 adapters will use a new host template. The template differs from SLI-4 adapters in that it does not have an eh_host_reset_handler. Lpfc has traditionally never had a host_reset. The host reset handler was added when we ran into a stuck hardware condition on a SLI-4 adapter. The host_reset will reset and reinit the pci function, clearing the hardware condition. Unfortunately, the host reset handler uses attach/detach code paths, which makes scsi_add_host() and scsi_remove_host() calls. Meaning, a host_reset will completely remove the scsi_host from the system. As a new call to scsi_add_host() is made, the shost# changes, which results in completely new scsi_devices and device names. All the older scsi devices on the old shost# are now orphaned and unrecoverable. We realize we need to re-implement the host_reset_handler so the scsi_host stays registered across the host_reset, but that will be a rather lengthy effort. In the short term, we had an immediate need to restore the SLI-3 devices to their working behavior, with the easiest path being to remove their host_reset handler. Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
This will detect and send an async event if overtemp is detected Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Ondrej Zary authored
The loop in aha1542_outb with double-check is no longer needed, remove it. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Ondrej Zary authored
Bus reset always fails because aha1542_reset waits for the controller to assert the INIT bit (Mailbox Initialization Required) which it never does. This bit is asserted only after host reset. Remove the requirement for INIT bit (we really need only the IDLE bit). Signed-off-by:
-
Ondrej Zary authored
Remove aha1542_lock and use host_lock instead. Remove interrupt and queuecommand function wrappers. Remove locking from lowlevel _out and _in functions, they now can onle be called (at runtime) with host_lock being held. Remove ssleep(4) in aha1542_reset as we can't sleep while holding a spinlock. It's useless anyway as wait_mask will wait until the controller is idle and kernel waits for 10 seconds (HOST_RESET_SETTLE_TIME) after that. Signed-off-by:
-
Ondrej Zary authored
Enabling DEBUG disables write commands and devices with ID > 1. Remove this "feature" to allow real debugging. Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Remove DEB macro and join ifdef DEBUG blocks Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Pass struct Scsi_Host *sh and dma parameters instead of index to aha1542_set_bus_times. This is required for printk conversion. Signed-off-by:
-
Ondrej Zary authored
Pass struct Scsi_Host * to functions instead of base address. This reduces the number of parameters and is also required for printk conversion. Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Signed-off-by:
-
Ondrej Zary authored
Fix include guard in header file and remove useless changelog Signed-off-by:
-
