Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.

Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.

Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use l4_tunnel type generically to keep code flow simple.

Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.

If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.

If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.

ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.

Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is not necessary to print FD filter add/delete log with
normal debug settings because ethtool -n ethx shows all the FD-SB
filters on an interface. The log can still be turned on through higher
debug levels and it will continue to print a log if there was an error
in the add/delete process.

Change-ID: I67db2baf49e2075d2f537de40f7895e5b02cd610
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Only print the port and veb stats if this is the first partition
of a multiplexed port.

Change-ID: I7ce0c323cdee5cfd2e54d8bea5b0b9102987e671
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.

Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition.  This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny.  Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.

Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.

Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There were some additional spaces and strange (double swapping) logic
in this function that I started looking at because sparse was warning.

This fixes the sparse warning and fixes up the other issues.

Change-ID: I72a91a4197cd45921602649040e6bd25e5f17c0a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel returns a u32 for netif_msg_init, and we were storing
it in a u16.  Fix the width of the datatype.

Change-ID: I4b23326e5707c91cd59325c5a1ccb2ba7a3974fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove LE16 to CPU endianes conversion from i40e_read_nvm_word_srctl
function, as it's already done by register read function.

Change-ID: I739f0f20a9b8e18223e54c0ca5443e63d75da878
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This series of code was repeated twice, remove one of them.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.

Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.

Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fengguang reported, that on openrisc and avr32 architectures, we
get the following linker errors on *_defconfig builds that have
no bpf syscall support:

  net/built-in.o:(.rodata+0x1cd0): undefined reference to `bpf_map_lookup_elem_proto'
  net/built-in.o:(.rodata+0x1cd4): undefined reference to `bpf_map_update_elem_proto'
  net/built-in.o:(.rodata+0x1cd8): undefined reference to `bpf_map_delete_elem_proto'

Fix it up by providing built-in weak definitions of the symbols,
so they can be overridden when the syscall is enabled. I think
the issue might be that gcc is not able to optimize all that away.
This patch fixes the linker errors for me, tested with Fengguang's
make.cross [1] script.

  [1] https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.crossReported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: d4052c4a ("ebpf: remove CONFIG_BPF_SYSCALL ifdefs in socket filter code")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some drivers use copybreak to copy tiny frames into smaller skb,
and this smaller skb might not have skb->head_frag set for various
reasons.

skb_gro_receive() currently doesn't allow to aggregate the smaller skb
into the previous GRO packet if this GRO packet has at least 2 MSS in
it.

Following workload easily demonstrates the problem.

netperf -t TCP_RR -H target -- -r 3000,3000

(tcpdump shows one GRO packet with 2 MSS, plus one additional packet of
104 bytes that should have been appended.)

It turns out that we can remove code from skb_gro_receive(), because
commit 8a29111c ("net: gro: allow to build full sized skb") and its
followups removed the assumption that a GRO packet with a frag_list had
to have an empty head.

Removing this code allows the aggregation of the last (incomplete) frame
in some RPC workloads. Note that tcp_gro_receive() already takes care of
forcing a flush if necessary, including this case.

If we want to avoid using frag_list in the first place (in forwarding
workloads for example, as the outgoing NIC is generally not able to cope
with skbs having a frag_list), we need to address this separately.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get a static checker warning here on devel kernels:

	drivers/net/hamradio/mkiss.c:560 ax_xmit()
	warn: variable dereferenced before check 'skb' (see line 532)

It turns out that the NULL check can be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Add QCN support to the DCB NL layer

This series from Shani Michaeli adds support for the IEEE QCN attribute
to the kernel DCB NL stack, and implementation in the mlx4 driver which
programs the firmware according to the admin directives.

changes from V0:

 - applied feedback from John and added his acked-by to patch #1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the IEEE DCB handlers for set/get QCN parameters and
statistics reading per TC.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device capability, firmware command opcode and etc prior elements
needed for QCN suppprt. Disable SRIOV VF view/access for QCN is disabled.

While here, remove a redundant offset definition into the
QUERY_DEV_CAP mailbox.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As specified in 802.1Qau spec. Add this optional attribute to the
DCB netlink layer. To allow for application to use the new attribute,
NIC drivers should implement and register the  callbacks ieee_getqcn,
ieee_setqcn and ieee_getqcnstats.

The QCN attribute holds a set of parameters for management, and
a set of statistics to provide informative data on Congestion-Control
defined by this spec.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
The rest of the FIB patches (add key_vector to fib_table)

This patch series is the rest of what I had originally planned for this kernel
release.  It adds a structure called key_vector which is embedded within
every tnode, leaf, and the trie root itself.  By doing this we can navigate
from any point within the trie to any other point fairly quickly and
avoiding NULL pointer checks in the case of a backtrace.  As a result we
can pipeline things a bit further since we don't have to worry about
dereferencing NULL in a backtrace.  This can amount to significant savings
on a long backtrace.

I decided to drop the up-level code as that conflicts with combining the
main and local tries.  I have one patch as an RFC that currently combines
the tries however it still needs some work as we have to split the local
and main tries in the event of custom rules being defined.  As such we are
probably going to be doing some more hacking on fib_table_flush_external as
that will also need to flush the local entries from the main trie and place
them back in the local trie.

v2: Rebased on the switchdev FIB offload work
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change makes it so that the root of the trie contains a key_vector, by
doing this we make room to essentially collapse the entire trie by at least
one cache line as we can store the information about the tnode or leaf that
is pointed to in the root.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change pulls the parent pointer from the key_vector and places it in
the tnode structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This pulls the information about the child array out of the key_vector and
places it in the tnode since that is where it is needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RCU is only needed once for the entire node, not once per key_vector so we
can pull that out and move it to the tnode structure.

In addition add accessors to be used inside the RCU functions so that we
can more easily get from the key vector to either the tnode or the trie
pointers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change pulls the fields not explicitly needed in the key_vector and
placed them in the new tnode structure.  By doing this we will eventually
be able to reduce the key_vector down to 16 bytes on 64 bit systems, and
12 bytes on 32 bit systems.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are now checking the length of a key_vector instead of a tnode so it
makes sense to probably just rename this to child_length since it would
probably even be applicable to a leaf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I am replacing the tnode_get_child call with get_child since we are
techically pulling the child out of a key_vector now and not a tnode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the tnode to key_vector.  The key_vector will be the eventual
container for all of the information needed by either a leaf or a tnode.
The final result should be much smaller than the 40 bytes currently needed
for either one.

This also updates the trie struct so that it contains an array of size 1 of
tnode pointers.  This is to bring the structure more inline with how an
actual tnode itself is configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resize related functions now all return a pointer to the pointer that
references the object that was resized.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change just does a couple of minor cleanups on
fib_table_flush_external.  Specifically it addresses the fact that resize
was being called even though nothing was being removed from the table, and
it drops an unecessary indent since we could just call continue on the
inverse of the fi && flag check.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ZynqMP soc has single interrupt for all the queue events. So,
passing the IRQF_SHARED flag for interrupt registration call.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include multi queue support for the ethernet IP version in xilinx ZynqMP
SoC.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2015-03-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Major changes:

brcmfmac:

* sdio improvements
* add a debugfs file so users can provide us all the revinfo we could
  ask for

iwlwifi:

* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements

ath9k:

* add per-vif TX power capability
* BT coexistance fixes

ath10k:

* qca6174: enable STA transmit beamforming (TxBF) support
* disable multi-vif power save by default

bcma:

* enable support for PCIe Gen 2 host devices
Signed-off-by: David S. Miller <davem@davemloft.net>

When building without CONFIG_NET_SWITCHDEV,
netdev_switch_fib_ipv4_abort is defined in the header file. It must
be static inline to avoid build failure at link time.

Fixes: 8e05fd71 ("fib: hook IPv4 fib for hardware offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the nla length is less than 2 then the nla data could be accessed
beyond the accessible bounds. So ensure that the nla is big enough to
at least read the via_family before doing so. Replace magic value of
2.

Fixes: 03c05665 ("mpls: Basic support for adding and removing routes")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petri Gynther says:

====================
net: bcmgenet: preparation for multiple Rx queues

Three small patches in preparation for supporting multiple Rx queues:
1. set hw_params->rx_queues = 0
2. adjust the call to alloc_etherdev_mqs()
3. add GENET_Q16_RX_BD_CNT and hw_params->rx_bds_per_q
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for supporting multiple Rx queues, add GENET_Q16_RX_BD_CNT
and hw_params->rx_bds_per_q.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>