- 31 Oct, 2018 16 commits
-
-
Madhav Chauhan authored
This patch disables both DSI ports by writing to DDI_BUF_CTL registers as part of DSI encoder disable sequence. Signed-off-by:
Madhav Chauhan <madhav.chauhan@intel.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Madhav Chauhan authored
This patch disables portsync mode if DSI link is operating in dual link mode by writing to TRANS_DDI_FUNC_CTL2 registers. Signed-off-by:
-
Madhav Chauhan authored
This patch disables DDI function by writing to TRANS_DDI_FUNC_CTL registers of DSI ports as part of DSI disable sequence. Signed-off-by:
-
Madhav Chauhan authored
As part of DSI disabling sequence, DSI link need to enter in ULPS by writing into DSI_LP_MSG register. This patch does the same using a wrapper function. Signed-off-by:
-
Madhav Chauhan authored
This patch sends command and executes display off, assert reset, power off VBT seqeuences to power down DSI panel. Patch also adds high level function to wrap all the panel sepcific programming during DSI disabling. Signed-off-by:
-
Madhav Chauhan authored
This patch disables transcoders by writing to TRANS_CONF registers for each DSI ports. v2 by Jani: - Wait for pipeconf active to go low Signed-off-by:
-
Madhav Chauhan authored
This patch disbles backlight of DSI panel by using VBT BACKLIGHT_OFF sequence and panel specific disable functions. Signed-off-by:
-
Madhav Chauhan authored
This patch enables backlight of DSI panel by using VBT BACKLIGHT_ON sequence and panel specific functions. Signed-off-by:
-
Madhav Chauhan authored
Driver needs payload/header credits for sending any command and data over DSI link. These credits are released once command or data sent to link. This patch adds functions to wait for releasing of payload and header credits. As per BSPEC, driver needs to ensure that all of commands/data has been dispatched to panel before the transcoder is enabled. This patch implement those steps i.e. sending NOP DCS command, wait for header/payload credit to be released etc. v2 by Jani: - squash the credit wait helpers patch with the first user - pass dev_priv to the credit wait helpers - bikeshed credit helper names - wait for *at least* the current maximum number of credits - indentation fix - add helpers for credits available Signed-off-by:
-
Jonathan Gray authored
Commit b2441318 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license") added "SPDX-License-Identifier: GPL-2.0" to files which previously had no license, change this to MIT for intel_ringbuffer.h matching the license text of intel_ringbuffer.c. Signed-off-by:
Jonathan Gray <jsg@jsg.id.au> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
Madhav Chauhan authored
This patch execute poweron, deassert reset, display on VBT sequences and send TURN_ON DSI command to panel for powering it up. Signed-off-by:
-
Madhav Chauhan authored
This patch programs maximum size of the payload transmitted from peripheral back to the host processor using short packet as a part of panel programming. v2: Rebase v3 by Jani: - Add FIXME note. Signed-off-by:
-
Madhav Chauhan authored
Move DSI connector functions to intel_dsi.c and make them available to both legacy and ICL DSI. v2 by Jani: - Move the functions to intel_dsi.c - Don't reuse intel_dsi_connector_destroy() Signed-off-by:
-
Madhav Chauhan authored
This patch moves intl_dsi_host_init() code to intel_dsi.c so that legacy and gen11 DSI code can share this code. v2 by Jani: - Move the shared stuff to intel_dsi.c Signed-off-by:
-
Matthew Auld authored
When using softpin it's not enough to just pad the vma size, we also need to ensure the vma offset is at the start of the pt boundary, if we plan to utilize 64K pages. Therefore to improve test coverage we should use both aligned and unaligned gtt offsets in igt_write_huge. Suggested-by:
Matthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Hang Yuan authored
This reverts commit c9e66688. Checked GVT codes that guest PPGTT PTE flag bits are propagated to shadow PTE. Read/write bit is not changed. Further tested by i915 self-test case "igt_ctx_readonly". No error or GPU hang was detected. So enable read-only support under GVT. Signed-off-by:
Hang Yuan <hang.yuan@linux.intel.com> Acked-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1540883281-11359-1-git-send-email-hang.yuan@linux.intel.comAcked-by:
-
- 30 Oct, 2018 4 commits
-
-
Animesh Manna authored
ICL supports DC5, DC6, and DC9. Enable DC9 during screen-off, and enable DC5/6 when appropriate. v2: (James Ausmus) - Also handle ICL as GEN9_LP in i915_drm_suspend_late and i915_drm_suspend_early - Add DC9 to gen9_dc_mask for ICL - Re-order GEN checks for newest platform first - Use INTEL_GEN instead of INTEL_INFO->gen - Use INTEL_GEN >= 11 instead of IS_ICELAKE - Consolidate GEN checks v3: (James Ausmus) - Also allow DC6 for ICL (Imre, Art) - Simplify !(GEN >= 11) to GEN < 11 (Imre) v4: (James Ausmus) - Don't call intel_power_sequencer_reset after DC9 for Gen11+, as the PPS regs are Always On - Rebase against upstream changes v5: (Anusha Srivatsa) - rebased against the latest upstream changes. v6: (Anusha Srivatsa) - rebased.Use INTEL_GEN consistently. - Simplify the code (Rodrigo) v7: rebased. Change order according to platforms(Jyoti) v8: rebased. Change the check from platform specific to HAS_PCH_SPLIT(). Add comment in code to be more clear.(Rodrigo) Cc: Imre Deak <imre.deak@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Animesh Manna <animesh.manna@intel.com> Signed-off-by:
James Ausmus <james.ausmus@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Tested-by:
Jyoti Yadav <jyoti.r.yadav@intel.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Chris Wilson authored
If we reduce the suspend function for intel_opregion to do the minimum required, the resume function can also do the simple task of notifier the ACPI bios that we are back. This avoid some nasty restrictions on the likes of register_acpi_notifier() that are not allowed during the early phase of resume. v2: Keep the order of acpi notify vs turning off ardy/drdy the same. Signed-off-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181030110554.4111-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
If we can prevent stray writes from landing in the scratch page, we can reuse the same page and same scratch PT for all contexts without fear of information leaks and side-channels. Signed-off-by:
-
Chris Wilson authored
Record the scratch PTE encoding upon creation rather than recomputing the bits everytime. This is important for the next patch where we forgo having a valid scratch page with which we may compute the bits and so require keeping the PTE value instead. v2: Fix up scrub_64K to use scratch_pte as well. Signed-off-by:
-
- 29 Oct, 2018 15 commits
-
-
Dhinakaran Pandiyan authored
intel_fb_pitch_limit() has the parameters pixel_format and fb_modifier switched in their positions. The parameters are however used correctly, but change the order for consistency. Also use kernel data types for both parameters. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181026195342.16828-1-dhinakaran.pandiyan@intel.com
-
Dhinakaran Pandiyan authored
The PLANE_AUX_OFFSET mmio does not exist on ICL, do not program it. We'll still calculate the aux offset as it is required for adjusing x-y offsets. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
-
Dhinakaran Pandiyan authored
A framebuffer can comprise surfaces with distinct tiling formats, making checks against modifier alone insufficient. Make use of a function to identify a linear surface based on both modifier and color plane. v2: Typo fix v3: remove 'inline' from function definition (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Dhinakaran Pandiyan authored
The bits weren't defined in descending order. v2: Move definitions in a separate patch (Manasi) Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181005185643.31660-2-dhinakaran.pandiyan@intel.com
-
Dhinakaran Pandiyan authored
The shifts for VSC_SELECT bits are wrong, fix it. Good thing is the definitions are unused. v2: Moves definitions in another patch (Manasi) Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Fixes: 7af2be6d ("drm/i915/icl: Add VIDEO_DIP registers") Signed-off-by:
-
Rodrigo Vivi authored
The specially case for SKL for not controlled sagv is already taken care inside intel_enable_sagv, so there's no need to duplicate the check here. v2: Go one step further and remove skl special case. (Jani) v3: Separate runtime status handle from has_sagv flag. v4: Go back and accept simple Jani proposed solution. Signed-off-by:
-
Chris Wilson authored
The vm of two contexts are supposed to be independent, such that a stray write by one cannot be detected by another. Normally the GTT is filled explicitly by userspace, but the space in between objects is filled with a scratch page -- and that scratch page should not be able to form an inter-context backchannel. Signed-off-by:
-
Rodrigo Vivi authored
While checking the opportunity to add a display_gen check to allow glk and cnl to be on same bucket I noticed these FIXME cases here. So I got the confirmation from HW architect that we actually never needed this workaround. "GLK supports 2 pixel per clock, so pixel clock can be up to 2 * cdclk." So, this reverts commit 97f55ca5 ("drm/i915/glk: limit pixel clock to 99% of cdclk workaround") Fixes: 97f55ca5 ("drm/i915/glk: limit pixel clock to 99% of cdclk workaround") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Madhav Chauhan <madhav.chauhan@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: Arthur J Runyan <arthur.j.runyan@intel.com> Signed-off-by:
-
Rodrigo Vivi authored
commit ac657f64 ("drm/i915: Introduce IS_GEN macro") introduced GEN_FOREVER that was never used. My first attempt was to rename it to FOREVER since GEN is already part of the macro. Then I used coccinelle to change all -INTEL_GEN(e1) >= e2 +INTEL_GEN_RANGE(e1, e2, FOREVER) -INTEL_GEN(e1) <= e2 +INTEL_GEN_RANGE(e1, 0, e2) and I liked it. However I didn't like very much the remaining INTEL_GEN(dev_priv) < n and: INTEL_GEN(e1) < n INTEL_GEN_RANGE(e1, 0, n - 1) didn't make much sense either. So INTEL_GEN use for > or < seems a better unified way for unlimited bounds. So, no reason to keep GEN_FOREVER here. Let's kill before someone start using it. v2: Remove remaining GEN_FOREVER forgotten in a comment. (Daniel) Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-2-rodrigo.vivi@intel.com
-
Rodrigo Vivi authored
Whenever possible we should stick with IS_GEN<n> checks. Bitmaks has been introduced on commit ae7617f0 ("drm/i915: Allow optimized platform checks") for efficiency. Let's stick with it whenever possible. This patch was generated with coccinelle: spatch -sp_file is_gen.cocci *{c,h} --in-place is_gen.cocci: @gen2@ expression e; @@ -INTEL_GEN(e) == 2 +IS_GEN2(e) @gen3@ expression e; @@ -INTEL_GEN(e) == 3 +IS_GEN3(e) @gen4@ expression e; @@ -INTEL_GEN(e) == 4 +IS_GEN4(e) @gen5@ expression e; @@ -INTEL_GEN(e) == 5 +IS_GEN5(e) @gen6@ expression e; @@ -INTEL_GEN(e) == 6 +IS_GEN6(e) @gen7@ expression e; @@ -INTEL_GEN(e) == 7 +IS_GEN7(e) @gen8@ expression e; @@ -INTEL_GEN(e) == 8 +IS_GEN8(e) @gen9@ expression e; @@ -INTEL_GEN(e) == 9 +IS_GEN9(e) @gen10@ expression e; @@ -INTEL_GEN(e) == 10 +IS_GEN10(e) @gen11@ expression e; @@ -INTEL_GEN(e) == 11 +IS_GEN11(e) Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
-
Ramalingam C authored
Intel HDCP2.2 registers are defined with addr offsets and bit details. v2: Replaced the arith calc with _PICK [Sean Paul] v3: No changes. v4: %s/HDCP2_CTR_DDI/HDCP2_CTL_DDI [Uma] v5: Added parentheses for the parameters of macro. v6: No changes v7: No changes Signed-off-by:
Ramalingam C <ramalingam.c@intel.com> Reviewed-by:
Sean Paul <seanpaul@chromium.org> Reviewed-by:
Uma Shankar <uma.shankar@intel.com> Signed-off-by:
-
Ramalingam C authored
This patch adds HDCP register definitions for HDMI and DP HDCP adaptations. HDMI specific HDCP2.2 register definitions are added into drm_hdcp.h, where as HDCP2.2 register offsets in DPCD offsets are defined at drm_dp_helper.h. v2: bit_field definitions are replaced by macros. [Tomas and Jani] v3: No Changes. v4: Comments style and typos are fixed [Uma] v5: Fix for macros. v6: Adds _MS to the timeouts to represent units [Sean Paul] v7: Macro DP_HDCP_2_2_REG_EKH_KM_OFFSET renamed [Uma] Redundant macro is removed [Uma] Signed-off-by:
-
Ramalingam C authored
This patch defines the hdcp2.2 protocol messages for authentication. v2: bit_fields are removed. Instead bitmasking used. [Tomas and Jani] prefix HDCP_2_2_ is added to the macros. [Tomas] v3: No Changes. v4: Style and spellings are fixed [Uma] v5: Fix for macros. v6: comment for Type is improved [Sean Paul] v7: %s/HDCP_2_2_LPRIME_HALF_LEN/HDCP_2_2_V_PRIME_HALF_LEN [Uma] %s/uintxx_t/uxx v8: %s/eceiver_id/receiver_id Signed-off-by:
-
Ramalingam C authored
As a policy, this change considers all I915 programming failures and HW failures as ERRORS. Where as all HDCP failures due to the sink is considered as DEBUG logs. Signed-off-by:
-
Ramalingam C authored
Considering significant number of HDCP specific variables, it will be clean to have separate struct for HDCP. New structure called intel_hdcp is added within intel_connector. v2: struct hdcp statically allocated. [Sean Paul] enable and disable function parameters are retained.[Sean Paul] v3: No Changes. v4: Commit msg is rephrased [Uma] v5: Comment for mutex definition. v6: hdcp_ prefix from all intel_hdcp members are removed [Sean Paul] inline function intel_hdcp_to_connector is defined [Sean Paul] v7: %s/uint64_t/u64 v8: Rebased Signed-off-by:
-
- 26 Oct, 2018 5 commits
-
-
Chris Wilson authored
A danger encountered when resetting the seqno (using debugfs/i915_next_seqno) is that as we change the breadcrumb stored in the HWSP, it may be inspected by the signaler thread leading to confusion in our sanity checks. <0> [136.331342] i915/sig-347 3..s1 136336154us : execlists_submission_tasklet: rcs0 awake?=1, active=5 <0> [136.331373] i915/sig-347 3d.s2 136336155us : process_csb: rcs0 cs-irq head=5, tail=0 <0> [136.331402] i915/sig-347 3d.s2 136336155us : process_csb: rcs0 csb[0]: status=0x00000018:0x00000002, active=0x5 <0> [136.331434] i915/sig-347 3d.s2 136336156us : process_csb: rcs0 out[0]: ctx=2.1, global=219 (fence 46:8455) (current 219), prio=0 <0> [136.331466] i915/sig-347 3d.s2 136336156us : process_csb: rcs0 completed ctx=2 <0> [136.332027] gem_exec-1049 0.... 136336246us : reset_all_global_seqno.part.5: rcs0 seqno 219 (current 219) -> -43 <0> [136.332056] gem_exec-1049 0.... 136336251us : reset_all_global_seqno.part.5: bcs0 seqno 183 (current 183) -> -43 <0> [136.332085] gem_exec-1049 0.... 136336255us : reset_all_global_seqno.part.5: vcs0 seqno 191 (current 191) -> -43 <0> [136.332114] gem_exec-1049 0.... 136336259us : reset_all_global_seqno.part.5: vcs1 seqno 180 (current 180) -> -43 <0> [136.332143] gem_exec-1049 0.... 136336262us : reset_all_global_seqno.part.5: vecs0 seqno 212 (current 212) -> -43 <0> [136.332174] i915/sig-347 3.... 136336280us : intel_breadcrumbs_signaler: intel_breadcrumbs_signaler:673 GEM_BUG_ON(!i915_request_completed(rq)) Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181024104939.2861-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
Use the live_test struct to record the reset count before and compare it at the end of the test to assert that no mystery hang occurred during the test. v2: Check per-engine resets as well Signed-off-by:
-
Tvrtko Ursulin authored
Upcoming GuC code will need to read the fused off engine masks as well, and will also want to have them as enabled instead of disabled masks. To consolidate the read-out place we can store them in this fashion inside INTEL_INFO so they can be easily referenced in the future. Signed-off-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181018104106.30147-1-tvrtko.ursulin@linux.intel.com
-
Chris Wilson authored
Beware mixing unsigned long constants and 64b values, as on 32b the constant will be zero extended and discard the high 32b when used as a mask! Reported-by:
Sergii Romantsov <sergii.romantsov@globallogic.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108282Signed-off-by:
-
Chris Wilson authored
Since we use a 64b virtual GTT irrespective of the system, we want to ensure that the GTT computations remains 64b even on 32b systems, including treatment of huge virtual pages. No code generation changes on 64b: Reported-by:
-
