- 01 Feb, 2016 40 commits
-
-
Ernst Martin Witte authored
si2157_remove was calling kfree(dev) with possibly still active schedule_delayed_work(dev->stat_work). This caused kernel panics in call_timer_fn e.g. after rmmod cx23885. Signed-off-by:
Ernst Martin Witte <emw-linux-kernel@nocabal.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Ernst Martin Witte authored
af9033_remove was calling kfree(dev) with possibly still active schedule_delayed_work(&dev->stat_work). A similar bug in si2157 caused kernel panics in call_timer_fn e.g. after rmmod cx23885. Signed-off-by:
-
Ernst Martin Witte authored
af9013_remove was calling kfree(state) with possibly still active schedule_delayed_work(&state->statistics_work). A similar bug in si2157 caused kernel panics in call_timer_fn e.g. after rmmod cx23885. Signed-off-by:
-
Antti Palosaari authored
Sometimes i2c transfer fails. That happens especially when large amount of data is written sequentially eg. firmware download. Problem arises with both integrated rtl2832 demod and external mn88472 demod, which is clear indicator it is busy i2c bus issue. Use i2c core retry logic in order fix the issue by repeating failed message. Another solution which also works is to add ~100us delay between i2c messages - but repeating sounds more elegant and does not cause any extra delay for success cases. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Torbjörn Jansson authored
Add a new product id to dvb-usb-dvbsky for new version of TechnoTrend CT2-4650 CI Signed-off-by:
Torbjörn Jansson <torbjorn.jansson@mbox200.swipnet.se> Reviewed-by:
Olli Salonen <olli.salonen@iki.fi> Signed-off-by:
-
Stefan Pöschel authored
PIP tested with VLC. Diversity tested with the Windows driver. Signed-off-by:
Stefan Pöschel <basic.master@gmx.de> Signed-off-by:
-
Philipp Zabel authored
The Terratec Cinergy S2 USB BOX uses a Montage M88TS2022 tuner and a M88DS3103 demodulator, same as Technotrend TT-connect S2-4600. This patch adds the missing USB Product ID to make it work. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Andrei Koshkosh authored
According with: https://www.silabs.com/Support%20Documents/TechnicalDocs/Si2157-short.pdf The RF input frequency range of this demod is from 42MHz to 870 MHz. Signed-off-by:
-
Heiner Kallweit authored
Extend the locking to protect more critical actions like register accesses in the interrupt handlers. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
Only handle an interrupt if at least one combination of event bit and related interrupt bit is set. Previously it was just checked that at least one event bit and at least one interrupt bit are set. This fixes issues like the following which was caused by interrupt sharing: An interrupt intended for nvt_cir_isr was handled by nvt_cir_wake_isr first and because status bit CIR_WAKE_IRSTS_IR_PENDING was set the wake fifo was accidently cleared. This patch also fixes the bug that nvt_cir_wake_isr returned IRQ_HANDLED even if it detected that the (shared) interrupt was meant for another handler. Signed-off-by:
-
Heiner Kallweit authored
Most likely a copy & paste error. The wakeup interrupt supports less triggering events. Signed-off-by:
-
Heiner Kallweit authored
Add locking to nvt_enable_wake calls. Signed-off-by:
-
Heiner Kallweit authored
Check for the case that no Nuvoton chip is found on either EFM port. Also move the position of nvt_efm_disable to reduce the time the EFM ports are locked. Signed-off-by:
-
Sakari Ailus authored
The v4l2-common.h user space header was split off from videodev2.h, but the dual licensing of the videodev2.h (as well as other V4L2 headers) was missed. Change the license of the v4l2-common.h from GNU GPL v2 to both GNU GPL v2 and BSD. Sakari Ailus <sakari.ailus@iki.fi>: > Would you approve a license change of the patches to > include/uapi/linux/v4l2-common.h (formerly include/linux/v4l2-common.h) you > or your company have contributed from GNU GPL v2 to dual GNU GPL v2 and BSD > licenses, changing the copyright notice in the file as below (from > videodev2.h): > > -------------8<------------ > * This program is free software; you can redistribute it and/or modify > * it under the terms of the GNU General Public License as published by > * the Free Software Foundation; either version 2 of the License, or > * (at your option) any later version. > * > * This program is distributed in the hope that it will be useful, > * but WITHOUT ANY WARRANTY; without even the implied warranty of > * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > * GNU General Public License for more details. > * > * Alternatively you can redistribute this file under the terms of the > * BSD license as stated below: > * > * Redistribution and use in source and binary forms, with or without > * modification, are permitted provided that the following conditions > * are met: > * 1. Redistributions of source code must retain the above copyright > * notice, this list of conditions and the following disclaimer. > * 2. Redistributions in binary form must reproduce the above copyright > * notice, this list of conditions and the following disclaimer in > * the documentation and/or other materials provided with the > * distribution. > * 3. The names of its contributors may not be used to endorse or promote > * products derived from this software without specific prior written > * permission. > * > * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS > * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT > * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR > * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT > * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, > * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED > * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR > * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF > * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING > * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS > * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. > -------------8<------------ Mauro Carvalho Chehab <mchehab@osg.samsung.com>: > No problem from my side. Hans Verkuil <hans.verkuil@cisco.com>: > Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Aaro Koskinen <aaro.koskinen@nokia.com>: > This fine also for us. > > Acked-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by:
-
Benoit Parrot authored
The Camera Adaptation Layer (CAL) is a block which consists of a dual port CSI2/MIPI camera capture engine. Port #0 can handle CSI2 camera connected to up to 4 data lanes. Port #1 can handle CSI2 camera connected to up to 2 data lanes. The driver implements the required API/ioctls to be V4L2 compliant. Driver supports the following: - V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api - Asynchronous sensor sub device registration - DT support Signed-off-by:Benoit Parrot <bparrot@ti.com> Signed-off-by:
-
Benoit Parrot authored
Signed-off-by:
-
Benoit Parrot authored
Device Tree bindings for the Camera Adaptation Layer (CAL) driver Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Hans Verkuil authored
Sometimes when a Bayer pixelformat is selected the rendering of the OSD text by vivid was all wrong: every other line of the text was shifted by half the width or more. It turned out that to render Bayer formats the interleaved boolean is set to true in the tpg. This mode indicates a semi-biplanar mode where two interleaved planes are used to render the frame. From outside the tpg it looks like a single plane, but internally it is two planes. However, in the tpg_s_bytesperline() function the interleaved bool wasn't checked and only the bytesperline value for plane 0 was updated. But for the interleaved mode the same value has to be copied to bytesperline[1] as well. The effect was that whatever old value was left in bytesperline[1] was used, which caused all sorts of weird and seemingly unpredictable shifts. Reported-by:
Ove Brynestad <ovebryne@cisco.com> Signed-off-by:
-
Tiffany Lin authored
In v4l2-compliance utility, test QUERYBUF required correct length value to go through each planar to check planar's length in multi-planar buffer type Signed-off-by:
Tiffany Lin <tiffany.lin@mediatek.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Hans Verkuil authored
A driver might detect a new standard or DV timings, but it will never change to those new timings automatically. Instead it will send an event and let the application take care of it. Make this explicit in the documentation. Signed-off-by:
-
Ulrich Hecht authored
The rcar_vin driver relies on this. Signed-off-by:
Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by:
-
Mats Randgaard authored
i2c_wr() is called from ops and the interrupt service routine, while state->wr_data is shared and unprotected, and could be overwritten. This shared buffer is therefore replaced with a local array with fixed size. The array has the size of one EDID block (128 bytes) + 2 bytes i2c address, and the EDID is written block by block (up to 8 blocks). Signed-off-by:
Mats Randgaard <matrandg@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Skip validating the standards field in v4l2_valid_dv_timings() if the V4L2_DV_BT_CAP_CUSTOM capability is set, since that implies that non-standard timings are allowed. Signed-off-by:
-
Fugang Duan authored
Dead code found on below code: si476x_radio_add_new_custom(radio, SI476X_IDX_DIVERSITY_MODE); if (rval < 0) goto exit; si476x_radio_add_new_custom(radio, SI476X_IDX_INTERCHIP_LINK); if (rval < 0) ====> Dead code !!! goto exit; The piece of code miss return value check after calling .si476x_radio_add_new_custom(), the patch fix it. Signed-off-by:Fugang Duan <B38611@freescale.com> Signed-off-by:
-
Jean-Baptiste Theou authored
dma_area needs to be freed when the device is closed. Based on em23xx-audio.c Signed-off-by:
Jean-Baptiste Theou <jtheou@adeneo-embedded.us> Signed-off-by:
-
Dan Carpenter authored
The module_param() is "default_rds_buf" and the MODULE_PARM_DESC() should match. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
It "tx_mask" was intended instead of "tx_maxk". Signed-off-by:
-
Dan Carpenter authored
The intent was to return -1 on error and that's what the callers expect but the current code returns USHRT_MAX instead. Signed-off-by:
-
Philipp Zabel authored
During the recent vb2_buffer restructuring, the calculation of the buffer payload reported to userspace was accidentally broken for the first encoded frame, counting only the length of the headers. This patch re-adds the length of the actual frame data. Fixes: 2d700715 ("[media] media: videobuf2: Restructure vb2_buffer") Reported-by:
Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by:
Jan Luebbe <jlu@pengutronix.de> Cc: <stable@vger.kernel.org> # for v4.4 and up Signed-off-by:
-
Julia Lawall authored
This sp887x_config structure is never modified, so declare it as const. Done with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Julia Lawall authored
The or51211_config structure is never modified, so declare it as const. Done with the help of Coccinelle. Signed-off-by:
-
Julia Lawall authored
This mxl111sf_tuner_config structure is never modified, so declare it as const. There are some indentation changes to remain within 80 columns. Done with the help of Coccinelle. Signed-off-by:
Michael Ira Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Julia Lawall authored
This sp8870_config structure is never modified, so declare it as const. Done with the help of Coccinelle. Signed-off-by:
-
Insu Yun authored
Since kzalloc can be failed, if not properly handled, NULL dereference could be happened. Signed-off-by:
Insu Yun <wuninsu@gmail.com> Signed-off-by:
-
Insu Yun authored
Since kmalloc can be failed in memory pressure, if not properly handled, NULL dereference can be happend Signed-off-by:
-
Markus Elfring authored
Let us return directly if the element "status" of the variable "buf" indicates "BUFSTAT_READY". A check repetition can be excluded for the variable "ret" at the end then. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Markus Elfring authored
This issue was detected by using the Coccinelle software. 1. Let us return directly if a buffer allocation failed. 2. Delete the jump label "err" then. 3. Drop the explicit initialisation for the variable "ret" at the beginning. 4. Return zero as a constant at the end. Signed-off-by:
-
Markus Elfring authored
Return constant integer values without storing them in the local variable "err" or "rc". Signed-off-by:
-
Niklas Söderlund authored
Don't hide the error code. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Ezequiel Garcia authored
Calling vb2_set_plane_payload is enough, there's no need to set the planes[] bytesused field. Remove it. Signed-off-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by:
-
