Datasheet specifies typical and maximum execution times for which CMD
register is occupied after previous command execution. We took these
values as minimum and maximum time for usleep_range() call before making
a new command execution.

To be sure, that the CMD register is no longer occupied we need to wait
*at least* the maximum time specified by datasheet.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The set_to_preset_on_index sysfs attribute provides a boolean
configuration option to enable a preset operation on the respective
channel's counter when Index occurs. However, the corresponding
configuration bit on the Input/Output Control register must be set low
to enable the preset operation.

This patch inverts the internal driver boolean logic exposed via the
set_to_preset_on_index attribute in order to correctly configure the
device which expects an active low bit.

Fixes: 28e5d3bb ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The Input/Output Control register (IOR) is offset by 1 from the
respective channel data register. This patch fixes off-by-one errors
when attempting to write to a channel IOR where the base address was not
properly offset.

Fixes: 28e5d3bb ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The LS7266R1 requires bits 5 & 6 to be high in order to select the Index
Control Register. This patch fixes a typo that incorrectly selects the
Input/Output Control Register where the Index Control Register was
desired.

Fixes: 28e5d3bb ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove two passthrough macros that are only called from a single
location and make the resultant vmcall directly.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the already defined DIAG_SEVERITY values directly instead of special
postcode macro names.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There were two instances of FAILURE being misspelled in the s-Par
firmware postcode event enum that are fixed.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove guestlinuxdebug enum values that are no longer being used and
renumber remaining values accordingly.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The visorchipset.c functionality was moved into the visorbus driver
previously. This patch updates the s-Par firmware postcode values to
reflect this status.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_4.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_3.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_2.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use CURRENT_FILE_PC directly in the POSTCODE_LINUX macro instead of
relying on passthrough macros to provide it.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Leverage the 3 existing s-Par postcode macros to do a bit more work
and provide only 1 base postcode macro.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes all the unused pound defines currently in
vbuschannel.h.
Signed-off-by: Erik Arfvidson <erik.arfvidson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes all the unused pound defines currently in
vmcallinterface.h.
Signed-off-by: Erik Arfvidson <erik.arfvidson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgnc driver has no business creating "custom" sysfs files just for a
single tty driver.  Combined with the odd way they are created, it's
just a mess, so remove them entirely as I am tired of tripping over them
when doing driver core changes.

Cc: Lidza Louina <lidza.louina@gmail.com>
Cc: Mark Hounschell <markh@compro.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes sm750fb tabstop style warning
found by checkpatch.pl tool
Signed-off-by: Andrea Ghittino <aghittino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The scripts to replace NULL test got confused with the
macro parenthesis so the unlikely test in libcfs_private.h
ended up incorrect. This fixes this error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Trivial fix to spelling mistake "oustanding" to "outstanding".
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove one blank line in sequence of two empty lines.
Signed-off-by: Dawid Kurek <dawikur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Align parameters to open parenthesis.
Signed-off-by: Dawid Kurek <dawikur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"revId" needs to be unsigned because we use it to test:

	if (revId == SM750LE_REVISION_ID) {

and SM750LE_REVISION_ID is ((unsigned char )0xfe).

Fixes: 81dee67e ("staging: sm750fb: add sm750 to staging")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver was actually released with BSD license. It also gained GPL
when it was submitted to be included in the kernel.

Cc: Teddy Wang <teddy.wang@siliconmotion.com>
Cc: gzhou1 <guojian.zhou@windriver.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes UPDATE_STATS_GB macro in slic.h header file
and just inline code. This improve readability.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch remove UPDATE_STATS macro from
header slic.h which is not being used.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed checkpatch.pl warnings related to {} brace warnings for single
statement blocks.
Signed-off-by: Yamanappagouda Patil <goudapatilk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch warnings regarding the use of symbolic permissions.

Where the MOST_CHANNEL_ATTR macro is used, convert to octal
permissions over symbolic.

Where _ATTR is used directly, replace with _ATTR_RW/_ATTR_WO and
update the show/store function names appropriately.
Signed-off-by: Jason Litzinger <jlitzingerdev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a feature for the client and server to use
obd_connect_flags2 to communicate future feature flags. The
client should set this flag whenever any flags in that field
are requested, and the server should mask unsupported features
from this field (assuming it understands OBD_CONNECT_FLAGS2).
When checking if an OBD_CONNECT2_xxxx feature is supported,
the client/server needs to firstly check if OBD_CONNECT_FLAGS2
is supported, since this field is also beyond the end of the
old obd_connect_data.

Land the connection flags to upstream client earlier for reserving
the slot to avoid potential conflict with others.
Signed-off-by: Fan Yong <fan.yong@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7543
Reviewed-on: http://review.whamcloud.com/17647Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Patrick Farrell <paf@cray.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The connection flag OBD_CONNECT_OBDOPACK will be used for the
following the patch: LU-4215 optimize OUT protocol
http://review.whamcloud.com/15336

Land the connection flags to upstream client earlier for reserving
the slot to avoid potential conflict with others.
Signed-off-by: Fan Yong <fan.yong@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7543
Reviewed-on: http://review.whamcloud.com/17646Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Patrick Farrell <paf@cray.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The connection flag OBD_CONNECT_LOCK_AHEAD will be used for the
following the patch: LU-6917 LDLM lock ahead
http://review.whamcloud.com/13564

Land the connection flags to upstream client earlier for reserving
the slot to avoid potential conflict with others.
Signed-off-by: Fan Yong <fan.yong@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7543
Reviewed-on: http://review.whamcloud.com/17645Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Patrick Farrell <paf@cray.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The connection flag OBD_CONNECT_SUBTREE will be used for the
following the patch: LU-28 mounting of filesystem from MDS
http://review.whamcloud.com/5007

Land the connection flags to master earlier for reserving the
slot to avoid potential conflict with others.
Signed-off-by: Fan Yong <fan.yong@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7543
Reviewed-on: http://review.whamcloud.com/17644Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Patrick Farrell <paf@cray.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix users of flags that were using "int" instead of named enum.
Rename some "flags" variables to distinguish between different flags.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: http://review.whamcloud.com/15300
Reviewed-on: http://review.whamcloud.com/15301Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename LDLM_CANCEL_* flags (used with enum ldlm_lru_flags) to
LDLM_LRU_FLAGS_* to avoid confusion with enum ldlm_cancel_flags.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: http://review.whamcloud.com/15300
Reviewed-on: http://review.whamcloud.com/15301Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace usage of ldlm_wire_policy_data_t with named enums
to conform to upstream coding style.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: http://review.whamcloud.com/15300
Reviewed-on: http://review.whamcloud.com/15301Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace usage of ldlm_side_t with named enums
to conform to upstream coding style.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: http://review.whamcloud.com/15300
Reviewed-on: http://review.whamcloud.com/15301Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace usage of ldlm_policy_data_t with named enums
to conform to upstream coding style.
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6142
Reviewed-on: http://review.whamcloud.com/15300
Reviewed-on: http://review.whamcloud.com/15301Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-by: frank zago <fzago@cray.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want sizeof(struct lstcon_node) but instead we're getting the sizeof
a pointer.

Fixes: 8d78f0f2 ("staging: lustre: lnet: cleanup some of the > 80 line issues")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We should free "desc" before returning NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.10d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Fourth set of IIO new device support, features and cleaups for the 4.10 cycle.

Probably the final set before the merge window unless things get significantly
delayed.

New device support
* STM32 ADC core
  - new driver.  Interesting device with up to 3 ADCs with complex triggering
    options that will follow later. Note split into an 'mfd like' core that
    handles the interrupt sharing etc between the various instances present and
    a per ADC section that is instantiated as many times as needed.
  - device tree bindings.

Cleanups and minor fixes
* st_accel
  - inline per sensor data as the defines don't add any meaning and make it
    much harder to check if a given sensor has the right values.
* hid-magnetometer
  - sort out the associations of the associated attributes with the two types.