- 06 Jan, 2017 40 commits
-
-
Jaegeuk Kim authored
commit e87f7329 upstream. In the last ilen case, i was already increased, resulting in accessing out- of-boundary entry of do_replace and blkaddr. Fix to check ilen first to exit the loop. Fixes: 2aa8fbb9693020 ("f2fs: refactor __exchange_data_block for speed up") Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicolai Stange authored
commit 05e6ea26 upstream. The struct file_operations instance serving the f2fs/status debugfs file lacks an initialization of its ->owner. This means that although that file might have been opened, the f2fs module can still get removed. Any further operation on that opened file, releasing included, will cause accesses to unmapped memory. Indeed, Mike Marshall reported the following: BUG: unable to handle kernel paging request at ffffffffa0307430 IP: [<ffffffff8132a224>] full_proxy_release+0x24/0x90 <...> Call Trace: [] __fput+0xdf/0x1d0 [] ____fput+0xe/0x10 [] task_work_run+0x8e/0xc0 [] do_exit+0x2ae/0xae0 [] ? __audit_syscall_entry+0xae/0x100 [] ? syscall_trace_enter+0x1ca/0x310 [] do_group_exit+0x44/0xc0 [] SyS_exit_group+0x14/0x20 [] do_syscall_64+0x61/0x150 [] entry_SYSCALL64_slow_path+0x25/0x25 <...> ---[ end trace f22ae883fa3ea6b8 ]--- Fixing recursive fault but reboot is needed! Fix this by initializing the f2fs/status file_operations' ->owner with THIS_MODULE. This will allow debugfs to grab a reference to the f2fs module upon any open on that file, thus preventing it from getting removed. Fixes: 902829aa ("f2fs: move proc files to debugfs") Reported-by:
Mike Marshall <hubcap@omnibond.com> Reported-by:
Martin Brandenburg <martin@omnibond.com> Signed-off-by:
Nicolai Stange <nicstange@gmail.com> Signed-off-by:
-
Jaegeuk Kim authored
commit 204706c7 upstream. This reverts commit 1beba1b3. The perpcu_counter doesn't provide atomicity in single core and consume more DRAM. That incurs fs_mark test failure due to ENOMEM. Signed-off-by:
-
Sergey Karamov authored
commit 73b92a2a upstream. Currently data journalling is incompatible with encryption: enabling both at the same time has never been supported by design, and would result in unpredictable behavior. However, users are not precluded from turning on both features simultaneously. This change programmatically replaces data journaling for encrypted regular files with ordered data journaling mode. Background: Journaling encrypted data has not been supported because it operates on buffer heads of the page in the page cache. Namely, when the commit happens, which could be up to five seconds after caching, the commit thread uses the buffer heads attached to the page to copy the contents of the page to the journal. With encryption, it would have been required to keep the bounce buffer with ciphertext for up to the aforementioned five seconds, since the page cache can only hold plaintext and could not be used for journaling. Alternatively, it would be required to setup the journal to initiate a callback at the commit time to perform deferred encryption - in this case, not only would the data have to be written twice, but it would also have to be encrypted twice. This level of complexity was not justified for a mode that in practice is very rarely used because of the overhead from the data journalling. Solution: If data=journaled has been set as a mount option for a filesystem, or if journaling is enabled on a regular file, do not perform journaling if the file is also encrypted, instead fall back to the data=ordered mode for the file. Rationale: The intent is to allow seamless and proper filesystem operation when journaling and encryption have both been enabled, and have these two conflicting features gracefully resolved by the filesystem. Fixes: 44614711Signed-off-by:
Sergey Karamov <skaramov@google.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Dan Carpenter authored
commit 578620f4 upstream. We should set the error code if kzalloc() fails. Fixes: 67cf5b09 ("ext4: add the basic function for inline data support") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Darrick J. Wong authored
commit 7e6e1ef4 upstream. Don't load an inode with a negative size; this causes integer overflow problems in the VFS. [ Added EXT4_ERROR_INODE() to mark file system as corrupted. -TYT] Fixes: a48380f7 (ext4: rename i_dir_acl to i_size_high) Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Theodore Ts'o authored
commit c48ae41b upstream. The commit "ext4: sanity check the block and cluster size at mount time" should prevent any problems, but in case the superblock is modified while the file system is mounted, add an extra safety check to make sure we won't overrun the allocated buffer. Signed-off-by:
-
Theodore Ts'o authored
commit 5aee0f8a upstream. Fix a large number of problems with how we handle mount options in the superblock. For one, if the string in the superblock is long enough that it is not null terminated, we could run off the end of the string and try to interpret superblocks fields as characters. It's unlikely this will cause a security problem, but it could result in an invalid parse. Also, parse_options is destructive to the string, so in some cases if there is a comma-separated string, it would be modified in the superblock. (Fortunately it only happens on file systems with a 1k block size.) Signed-off-by:
-
Theodore Ts'o authored
commit cd6bb35b upstream. Centralize the checks for inodes_per_block and be more strict to make sure the inodes_per_block_group can't end up being zero. Signed-off-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
-
Chandan Rajendra authored
commit 30a9d7af upstream. The number of 'counters' elements needed in 'struct sg' is super_block->s_blocksize_bits + 2. Presently we have 16 'counters' elements in the array. This is insufficient for block sizes >= 32k. In such cases the memcpy operation performed in ext4_mb_seq_groups_show() would cause stack memory corruption. Fixes: c9de560dSigned-off-by:
Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Chandan Rajendra authored
commit 69e43e8c upstream. 'border' variable is set to a value of 2 times the block size of the underlying filesystem. With 64k block size, the resulting value won't fit into a 16-bit variable. Hence this commit changes the data type of 'border' to 'unsigned int'. Fixes: c9de560dSigned-off-by:
-
Theodore Ts'o authored
commit 1566a48a upstream. If there is an error reported in mballoc via ext4_grp_locked_error(), the code is holding a spinlock, so ext4_commit_super() must not try to lock the buffer head, or else it will trigger a BUG: BUG: sleeping function called from invalid context at ./include/linux/buffer_head.h:358 in_atomic(): 1, irqs_disabled(): 0, pid: 993, name: mount CPU: 0 PID: 993 Comm: mount Not tainted 4.9.0-rc1-clouder1 #62 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20150316_085822-nilsson.home.kraxel.org 04/01/2014 ffff880006423548 ffffffff81318c89 ffffffff819ecdd0 0000000000000166 ffff880006423558 ffffffff810810b0 ffff880006423580 ffffffff81081153 ffff880006e5a1a0 ffff88000690e400 0000000000000000 ffff8800064235c0 Call Trace: [<ffffffff81318c89>] dump_stack+0x67/0x9e [<ffffffff810810b0>] ___might_sleep+0xf0/0x140 [<ffffffff81081153>] __might_sleep+0x53/0xb0 [<ffffffff8126c1dc>] ext4_commit_super+0x19c/0x290 [<ffffffff8126e61a>] __ext4_grp_locked_error+0x14a/0x230 [<ffffffff81081153>] ? __might_sleep+0x53/0xb0 [<ffffffff812822be>] ext4_mb_generate_buddy+0x1de/0x320 Since ext4_grp_locked_error() calls ext4_commit_super with sync == 0 (and it is the only caller which does so), avoid locking and unlocking the buffer in this case. This can result in races with ext4_commit_super() if there are other problems (which is what commit 4743f839 was trying to address), but a Warning is better than BUG. Fixes: 4743f839Reported-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
-
Alex Porosanu authored
commit d128af17 upstream. The AEAD givenc descriptor relies on moving the IV through the output FIFO and then back to the CTX2 for authentication. The SEQ FIFO STORE could be scheduled before the data can be read from OFIFO, especially since the SEQ FIFO LOAD needs to wait for the SEQ FIFO LOAD SKIP to finish first. The SKIP takes more time when the input is SG than when it's a contiguous buffer. If the SEQ FIFO LOAD is not scheduled before the STORE, the DECO will hang waiting for data to be available in the OFIFO so it can be transferred to C2. In order to overcome this, first force transfer of IV to C2 by starting the "cryptlen" transfer first and then starting to store data from OFIFO to the output buffer. Fixes: 1acebad3 ("crypto: caam - faster aead implementation") Signed-off-by:
Alex Porosanu <alexandru.porosanu@nxp.com> Signed-off-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Eric W. Biederman authored
commit 84d77d3f upstream. It is the reasonable expectation that if an executable file is not readable there will be no way for a user without special privileges to read the file. This is enforced in ptrace_attach but if ptrace is already attached before exec there is no enforcement for read-only executables. As the only way to read such an mm is through access_process_vm spin a variant called ptrace_access_vm that will fail if the target process is not being ptraced by the current process, or the current process did not have sufficient privileges when ptracing began to read the target processes mm. In the ptrace implementations replace access_process_vm by ptrace_access_vm. There remain several ptrace sites that still use access_process_vm as they are reading the target executables instructions (for kernel consumption) or register stacks. As such it does not appear necessary to add a permission check to those calls. This bug has always existed in Linux. Fixes: v1.0 Reported-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
commit 64b875f7 upstream. When the flag PT_PTRACE_CAP was added the PTRACE_TRACEME path was overlooked. This can result in incorrect behavior when an application like strace traces an exec of a setuid executable. Further PT_PTRACE_CAP does not have enough information for making good security decisions as it does not report which user namespace the capability is in. This has already allowed one mistake through insufficient granulariy. I found this issue when I was testing another corner case of exec and discovered that I could not get strace to set PT_PTRACE_CAP even when running strace as root with a full set of caps. This change fixes the above issue with strace allowing stracing as root a setuid executable without disabling setuid. More fundamentaly this change allows what is allowable at all times, by using the correct information in it's decision. Fixes: 4214e42f96d4 ("v2.4.9.11 -> v2.4.9.12") Signed-off-by:
-
Linus Torvalds authored
commit d05c5f7b upstream. We truncated the possible read iterator to s_maxbytes in commit c2a9737f ("vfs,mm: fix a dead loop in truncate_inode_pages_range()"), but our end condition handling was wrong: it's not an error to try to read at the end of the file. Reading past the end should return EOF (0), not EINVAL. See for example https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1649342 http://lists.gnu.org/archive/html/bug-coreutils/2016-12/msg00008.html where a md5sum of a maximally sized file fails because the final read is exactly at s_maxbytes. Fixes: c2a9737f ("vfs,mm: fix a dead loop in truncate_inode_pages_range()") Reported-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Cc: Wei Fang <fangwei1@huawei.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Eric W. Biederman authored
commit bfedb589 upstream. During exec dumpable is cleared if the file that is being executed is not readable by the user executing the file. A bug in ptrace_may_access allows reading the file if the executable happens to enter into a subordinate user namespace (aka clone(CLONE_NEWUSER), unshare(CLONE_NEWUSER), or setns(fd, CLONE_NEWUSER). This problem is fixed with only necessary userspace breakage by adding a user namespace owner to mm_struct, captured at the time of exec, so it is clear in which user namespace CAP_SYS_PTRACE must be present in to be able to safely give read permission to the executable. The function ptrace_may_access is modified to verify that the ptracer has CAP_SYS_ADMIN in task->mm->user_ns instead of task->cred->user_ns. This ensures that if the task changes it's cred into a subordinate user namespace it does not become ptraceable. The function ptrace_attach is modified to only set PT_PTRACE_CAP when CAP_SYS_PTRACE is held over task->mm->user_ns. The intent of PT_PTRACE_CAP is to be a flag to note that whatever permission changes the task might go through the tracer has sufficient permissions for it not to be an issue. task->cred->user_ns is always the same as or descendent of mm->user_ns. Which guarantees that having CAP_SYS_PTRACE over mm->user_ns is the worst case for the tasks credentials. To prevent regressions mm->dumpable and mm->user_ns are not considered when a task has no mm. As simply failing ptrace_may_attach causes regressions in privileged applications attempting to read things such as /proc/<pid>/stat Acked-by:
Kees Cook <keescook@chromium.org> Tested-by:
Cyrill Gorcunov <gorcunov@openvz.org> Fixes: 8409cca7 ("userns: allow ptrace from non-init user namespaces") Signed-off-by:
-
NeilBrown authored
commit bcc7f5b4 upstream. bdev->bd_contains is not stable before calling __blkdev_get(). When __blkdev_get() is called on a parition with ->bd_openers == 0 it sets bdev->bd_contains = bdev; which is not correct for a partition. After a call to __blkdev_get() succeeds, ->bd_openers will be > 0 and then ->bd_contains is stable. When FMODE_EXCL is used, blkdev_get() calls bd_start_claiming() -> bd_prepare_to_claim() -> bd_may_claim() This call happens before __blkdev_get() is called, so ->bd_contains is not stable. So bd_may_claim() cannot safely use ->bd_contains. It currently tries to use it, and this can lead to a BUG_ON(). This happens when a whole device is already open with a bd_holder (in use by dm in my particular example) and two threads race to open a partition of that device for the first time, one opening with O_EXCL and one without. The thread that doesn't use O_EXCL gets through blkdev_get() to __blkdev_get(), gains the ->bd_mutex, and sets bdev->bd_contains = bdev; Immediately thereafter the other thread, using FMODE_EXCL, calls bd_start_claiming() from blkdev_get(). This should fail because the whole device has a holder, but because bdev->bd_contains == bdev bd_may_claim() incorrectly reports success. This thread continues and blocks on bd_mutex. The first thread then sets bdev->bd_contains correctly and drops the mutex. The thread using FMODE_EXCL then continues and when it calls bd_may_claim() again in: BUG_ON(!bd_may_claim(bdev, whole, holder)); The BUG_ON fires. Fix this by removing the dependency on ->bd_contains in bd_may_claim(). As bd_may_claim() has direct access to the whole device, it can simply test if the target bdev is the whole device. Fixes: 6b4517a7 ("block: implement bd_claiming and claiming block") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Linus Torvalds authored
commit 52bce911 upstream. Commit 8924feff ("splice: lift pipe_lock out of splice_to_pipe()") caused a regression when there were no more readers left on a pipe that was being spliced into: rather than the expected SIGPIPE and -EPIPE return value, the writer would end up waiting forever for space to free up (which obviously was not going to happen with no readers around). Fixes: 8924feff ("splice: lift pipe_lock out of splice_to_pipe()") Reported-and-tested-by:
Andreas Schwab <schwab@linux-m68k.org> Debugged-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Aleksa Sarai authored
commit 613cc2b6 upstream. If you have a process that has set itself to be non-dumpable, and it then undergoes exec(2), any CLOEXEC file descriptors it has open are "exposed" during a race window between the dumpable flags of the process being reset for exec(2) and CLOEXEC being applied to the file descriptors. This can be exploited by a process by attempting to access /proc/<pid>/fd/... during this window, without requiring CAP_SYS_PTRACE. The race in question is after set_dumpable has been (for get_link, though the trace is basically the same for readlink): [vfs] -> proc_pid_link_inode_operations.get_link -> proc_pid_get_link -> proc_fd_access_allowed -> ptrace_may_access(task, PTRACE_MODE_READ_FSCREDS); Which will return 0, during the race window and CLOEXEC file descriptors will still be open during this window because do_close_on_exec has not been called yet. As a result, the ordering of these calls should be reversed to avoid this race window. This is of particular concern to container runtimes, where joining a PID namespace with file descriptors referring to the host filesystem can result in security issues (since PRCTL_SET_DUMPABLE doesn't protect against access of CLOEXEC file descriptors -- file descriptors which may reference filesystem objects the container shouldn't have access to). Cc: dev@opencontainers.org Reported-by:
Michael Crosby <crosbymichael@gmail.com> Signed-off-by:
Aleksa Sarai <asarai@suse.de> Signed-off-by:
-
Eric W. Biederman authored
commit f84df2a6 upstream. When the user namespace support was merged the need to prevent ptrace from revealing the contents of an unreadable executable was overlooked. Correct this oversight by ensuring that the executed file or files are in mm->user_ns, by adjusting mm->user_ns. Use the new function privileged_wrt_inode_uidgid to see if the executable is a member of the user namespace, and as such if having CAP_SYS_PTRACE in the user namespace should allow tracing the executable. If not update mm->user_ns to the parent user namespace until an appropriate parent is found. Reported-by:
Jann Horn <jann@thejh.net> Fixes: 9e4a36ec ("userns: Fail exec for suid and sgid binaries with ids outside our user namespace.") Signed-off-by:
-
Richard Watts authored
commit 035cd485 upstream. The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term frequency drift. The frequency drift magnitude depends on the VCO update rate, which is inversely proportional to the PLL divider. The kernel DPLL configuration code results in a high value for the divider, leading to a long term drift high enough to cause USB transmission errors. In the worst case the USB PHY's ULPI interface can stop responding, breaking USB operation completely. This manifests itself on the Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the cable is bad?' in the kernel log. Errata sprz319 advisory 2.1 documents PLL values that minimize the drift. Use them automatically when DPLL5 is used for USB operation, which we detect based on the requested clock rate. The clock framework will still compute the PLL parameters and resulting rate as usual, but the PLL M and N values will then be overridden. This can result in the effective clock rate being slightly different than the rate cached by the clock framework, but won't cause any adverse effect to USB operation. Signed-off-by:
Richard Watts <rrw@kynesim.co.uk> [Upported from v3.2 to v4.9] Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by:
Ladislav Michl <ladis@linux-mips.org> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Cc: Adam Ford <aford173@gmail.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 5e0ad0d8 upstream. Commit [64047d7f ALSA: hda - ignore the assoc and seq when comparing pin configurations] intented to ignore both seq and assoc at pin comparing, but it only ignored seq. So that commit may still fail to match pins on some machines. Change the bitmask to also ignore assoc. v2: Use macro to do bit masking. Thanks to Hui Wang for the analysis. Fixes: 64047d7f ("ALSA: hda - ignore the assoc and seq when comparing...") Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit f73cd43a upstream. HP Z1 Gen3 AiO with Conexant codec doesn't give an unsolicited event to the headset mic pin upon the jack plugging, it reports only to the headphone pin. It results in the missing mic switching. Let's fix up by simply gating the jack event. Signed-off-by:
-
Hui Wang authored
commit 989dbe4a upstream. This group of new pins is not in the pin quirk table yet, adding them to the pin quirk table to fix the headset-mic problem. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Hui Wang authored
commit 64047d7f upstream. More and more pin configurations have been adding to the pin quirk table, lots of them are only different from assoc and seq, but they all apply to the same QUIRK_FIXUP, if we don't compare assoc and seq when matching pin configurations, it will greatly reduce the pin quirk table size. We have tested this change on a couple of Dell laptops, it worked well. Signed-off-by:
-
Sven Hahne authored
commit b5337cfe upstream. I'm using an Alienware 15 R2 and had to use the alienware quirks to get my headphone output working. I fixed it by adding, SND_PCI_QUIRK(0x1028, 0x0708, "Alienware 15 R2 2016", QUIRK_ALIENWARE) to the patch. Signed-off-by:
Sven Hahne <hahne@zeitkunst.eu> Signed-off-by:
-
Jussi Laako authored
commit 995c6a7f upstream. Sampling rate changes after first set one are not reflected to the hardware, while driver and ALSA think the rate has been changed. Fix the problem by properly stopping the interface at the beginning of prepare call, allowing new rate to be set to the hardware. This keeps the hardware in sync with the driver. Signed-off-by:
Jussi Laako <jussi@sonarnerd.net> Signed-off-by:
-
Con Kolivas authored
commit 82ffb6fc upstream. The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the following warning. [ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072), cval->res is probably wrong. [ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1 Adding it to the list of devices in volume_control_quirks makes it work properly, fixing related typo. Signed-off-by:
Con Kolivas <kernel@kolivas.org> Signed-off-by:
-
Krzysztof Opasiak authored
commit 3e448e13 upstream. ep_list inside gadget structure doesn't contain ep0. It is stored separately in ep0 field. This causes an urb hang if gadget driver decides to delay setup handling. On host side this is visible as timeout error when setting configuration. This bug can be reproduced using for example any gadget with mass storage function. Fixes: abdb2957 ("usbip: vudc: Add vudc_transfer") Signed-off-by:
Krzysztof Opasiak <k.opasiak@samsung.com> Acked-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Alan Stern authored
commit ccdb6be9 upstream. The UHCI controllers in Intel chipsets rely on a platform-specific non-PME mechanism for wakeup signalling. They can generate wakeup signals even though they don't support PME. We need to let the USB core know this so that it will enable runtime suspend for UHCI controllers. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
-
Felipe Balbi authored
commit e8f29bb7 upstream. usb_endpoint_maxp() returns wMaxPacketSize in its raw form. Without taking into consideration that it also contains other bits reserved for isochronous endpoints. This patch fixes one occasion where this is a problem by making sure that we initialize ep->maxpacket only with lower 10 bits of the value returned by usb_endpoint_maxp(). Note that seperate patches will be necessary to audit all call sites of usb_endpoint_maxp() and make sure that usb_endpoint_maxp() only returns lower 10 bits of wMaxPacketSize. Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Peter Chen authored
commit f1d3861d upstream. The current error handling flow uses incorrect goto label, fix it Fixes: d12a8727 ("usb: gadget: function: Remove redundant usb_free_all_descriptors") Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Rafał Miłecki authored
commit 89778ba3 upstream. Calling brightness_set manually isn't safe as some LED drivers don't implement this callback. The best idea is to just use a proper helper which will fallback to the brightness_set_blocking callback if needed. This fixes: [ 1461.761528] Unable to handle kernel NULL pointer dereference at virtual address 00000000 (...) [ 1462.117049] Backtrace: [ 1462.119521] [<bf228164>] (usbport_trig_port_store [ledtrig_usbport]) from [<c023f758>] (dev_attr_store+0x20/0x2c) [ 1462.129826] r7:dcabc7c0 r6:dee0ff80 r5:00000002 r4:bf228164 [ 1462.135511] [<c023f738>] (dev_attr_store) from [<c0169310>] (sysfs_kf_write+0x48/0x4c) [ 1462.143459] r5:00000002 r4:c023f738 [ 1462.147049] [<c01692c8>] (sysfs_kf_write) from [<c0168ab8>] (kernfs_fop_write+0xf8/0x1f8) [ 1462.155258] r5:00000002 r4:df4a1000 [ 1462.158850] [<c01689c0>] (kernfs_fop_write) from [<c0100c78>] (__vfs_write+0x34/0x120) [ 1462.166800] r10:00000000 r9:dee0e000 r8:c000fc24 r7:00000002 r6:dee0ff80 r5:c01689c0 [ 1462.174660] r4:df727a80 [ 1462.177204] [<c0100c44>] (__vfs_write) from [<c0101ae4>] (vfs_write+0xac/0x170) [ 1462.184543] r9:dee0e000 r8:c000fc24 r7:dee0ff80 r6:b6f092d0 r5:df727a80 r4:00000002 [ 1462.192319] [<c0101a38>] (vfs_write) from [<c01028dc>] (SyS_write+0x4c/0xa8) [ 1462.199396] r9:dee0e000 r8:c000fc24 r7:00000002 r6:b6f092d0 r5:df727a80 r4:df727a80 [ 1462.207174] [<c0102890>] (SyS_write) from [<c000fa60>] (ret_fast_syscall+0x0/0x3c) [ 1462.214774] r7:00000004 r6:ffffffff r5:00000000 r4:00000000 [ 1462.220456] Code: bad PC value [ 1462.223560] ---[ end trace 676638a3a12c7a56 ]--- Reported-by:
Ralph Sennhauser <ralph.sennhauser@gmail.com> Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Fixes: 0f247626 ("usb: core: Introduce a USB port LED trigger") Signed-off-by:
-
Mathias Nyman authored
commit 37be6676 upstream. USB-3 does not have any link state that will avoid negotiating a connection with a plugged-in cable but will signal the host when the cable is unplugged. For USB-3 we used to first set the link to Disabled, then to RxDdetect to be able to detect cable connects or disconnects. But in RxDetect the connected device is detected again and eventually enabled. Instead set the link into U3 and disable remote wakeups for the device. This is what Windows does, and what Alan Stern suggested. Cc: Alan Stern <stern@rowland.harvard.edu> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Felipe Balbi authored
commit 6b9018d4 upstream. In case of High-Speed, High-Bandwidth endpoints, we need to tell DWC3 that we have more than one packet per interval. We do that by setting PCM1 field of Isochronous-First TRB. Signed-off-by:
-
Nathaniel Quillin authored
commit 30121604 upstream. Add device-id entry for GW Instek AFG-125, which has a byte swapped bInterfaceSubClass (0x20). Signed-off-by:
Nathaniel Quillin <ndq@google.com> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Johan Hovold authored
commit 6774d5f5 upstream. Kill urbs and disable read before returning from open on failure to retrieve the line state. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Giuseppe Lippolis authored
commit d8a12b71 upstream. Adding registration for 3G modem DWM-158 in usb-serial-option Signed-off-by:
Giuseppe Lippolis <giu.lippolis@gmail.com> Signed-off-by:
-
Daniele Palmas authored
commit 5b09eff0 upstream. This patch adds support for PIDs 0x1040, 0x1041 of Telit LE922A. Since the interface positions are the same than the ones used for other Telit compositions, previous defined blacklists are used. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
