- 21 Aug, 2021 30 commits
-
-
Chin-Yen Lee authored
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms, to wait firmware finish preliminary work and then update the value of WOWLAN_WAKE_REASON register to zero. But later firmware will start wow function with power-saving mode, in which mode the value of WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and return fail. We use read_poll_timeout instead to check the value to avoid this issue. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
-
Chin-Yen Lee authored
We find the power sequence of system suspend flow don't meet the criteria when using 8822CE-VR chip by rfe-type 6, because the reference clock form host is sometimes late. To avoid the behavoir, we keep CLKREQ# signal to low during suspend to make sure the reference clock arrival in time. Signed-off-by:
-
Po-Hao Huang authored
Finetune parameter for firmware. Previous mode neglects environment impacts and could lead to performance downgrade in some cases. This new mode makes fw adapts better under noisy environment. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
Enabling this improves tx performance for long distance transmission. We used to enable stbc by the rx stbc cap of the associated station. But rx cap will be masked out in ieee80211_ht_cap_ie_to_sta_ht_cap if we do not declare tx stbc. Signed-off-by:
-
Chin-Yen Lee authored
We find that some disconnect events are related to failure of tx report, so increase log level to improve debuggability. Signed-off-by:
-
Chris Chiu authored
The TX A-MPDU aggregation is not handled in the driver since the ieee80211_start_tx_ba_session has never been started properly. Start and stop the TX BA session by tracking the TX aggregation status of each TID. Fix the ampdu_action and the tx descriptor accordingly with the given TID. Signed-off-by:
Chris Chiu <chris.chiu@canonical.com> Signed-off-by:
-
Chris Chiu authored
There will be crazy numbers of interrupts triggered by 8188cu and 8192cu module, around 8000~10000 interrupts per second, on the usb host controller. Compare with the vendor driver source code, it's mapping to the configuration CONFIG_USB_INTERRUPT_IN_PIPE and it is disabled by default. Since the interrupt transfer is neither used for TX/RX nor H2C commands. Disable it to avoid the excessive amount of interrupts for the 8188cu and 8192cu module which I only have for verification. Signed-off-by:
Jes Sorensen <Jes.Sorensen@gmail.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the arrays wpa_oui and wps_oui on the stack but instead them static const. Makes the object code smaller by 63 bytes: Before: text data bss dec hex filename 29453 5451 64 34968 8898 .../wireless/marvell/mwifiex/sta_ioctl.o After: text data bss dec hex filename 29356 5611 64 35031 88d7 ../wireless/marvell/mwifiex/sta_ioctl.o (gcc version 10.3.0) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. This helps with the ongoing efforts to globally enable -Warray-bounds and get us closer to being able to tighten the FORTIFY_SOURCE routines on memcpy(). This issue was found with the help of Coccinelle and audited and fixed, manually. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/79 Link: https://github.com/KSPP/linux/issues/109Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
Tuo Li authored
There is no case in which the variable cmd_node->cmd_skb has no ->data, and thus the variable host_cmd is guaranteed to be not NULL. Therefore, the null-pointer check is redundant and can be dropped. Reported-by:
TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by:
Tuo Li <islituo@gmail.com> Tested-by:
-
wengjianfeng authored
Some of the code is redundant, so goto statements are used to remove them Signed-off-by:
wengjianfeng <wengjianfeng@yulong.com> Signed-off-by:
-
Claudiu Beznea authored
Use devm_clk_get_optional() for rtc clock: it simplifies a bit the code. Signed-off-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by:
-
Claudiu Beznea authored
Dispose IRQ on failure path. Signed-off-by:
-
Claudiu Beznea authored
Use goto labels on error path for probe functions. This makes code easier to read. With this introduce also netdev_cleanup and call it where necessary. Signed-off-by:
-
Colin Ian King authored
Don't populate arrays the stack but instead make them static const. Replace array channel_info with channel_all since it contains the same data as channel_all. Makes object code smaller by 961 bytes. Before: text data bss dec hex filename 128147 44250 1024 173421 2a56d ../realtek/rtlwifi/rtl8192de/phy.o After text data bss dec hex filename 127122 44314 1024 172460 2a1ac ../realtek/rtlwifi/rtl8192de/phy.o (gcc version 10.2.0) Signed-off-by:
-
Colin Ian King authored
The variables rtstatus and place are being initialized with a values that are never read, the initializations are redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: -
Dan Carpenter authored
Return -ENODEV instead of success for unsupported devices. Fixes: 54fdb318 ("rsi: add new device model for 9116") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
This code returns success if the kmemdup() fails, but obviously it should return -ENOMEM instead. Fixes: e5a1ecc9 ("rsi: add firmware loading for 9116 device") Signed-off-by:
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Split memcpy() for each address range to help memcpy() correctly reason about the bounds checking. Avoids the future warning: In function 'fortify_memcpy_chk', inlined from 'memcpy_toio' at ./include/asm-generic/io.h:1204:2, inlined from 'ray_build_header.constprop' at drivers/net/wireless/ray_cs.c:984:3: ./include/linux/fortify-string.h:285:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning] 285 | __write_overflow_field(p_size_field, size); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:Kees Cook <keescook@chromium.org> Signed-off-by:
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. libipw_read_qos_param_element() copies a struct libipw_info_element into a struct libipw_qos_information_element, but is actually wanting to copy into the larger struct libipw_qos_parameter_info (the contents of ac_params_record[] is later examined). Refactor the routine to perform centralized checks, and copy the entire contents directly (since the id and len members match the elementID and length members): struct libipw_info_element { u8 id; u8 len; u8 data[]; } __packed; struct libipw_qos_information_element { u8 elementID; u8 length; u8 qui[QOS_OUI_LEN]; u8 qui_type; u8 qui_subtype; u8 version; u8 ac_info; } __packed; struct libipw_qos_parameter_info { struct libipw_qos_information_element info_element; u8 reserved; struct libipw_qos_ac_parameter ac_params_record[QOS_QUEUE_NUM]; } __packed; Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: -
Len Baker authored
Dynamic size calculations (especially multiplication) should not be performed in memory allocator function arguments due to the risk of them overflowing. This could lead to values wrapping around and a smaller allocation being made than the caller was expecting. Using those allocations could lead to linear overflows of heap memory and other misbehaviors. To avoid this scenario, use the struct_size helper. Signed-off-by:
Len Baker <len.baker@gmx.com> Signed-off-by:
-
Andy Shevchenko authored
Use %*ph format to print small buffer as hex string. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Angus Ainslie authored
Add HW and SDIO ids for use with the SparkLan AP6275S Add the firmware mapping structures for the BRCM43752 chipset. The 43752 needs some things setup similar to the 43012 chipset. The WATERMARK shows better performance when initialized to the 4373 value. Signed-off-by:
Angus Ainslie <angus@akkea.ca> Signed-off-by:
-
Sean Anderson authored
This puts tasks submitted to the SDIO workqueue at the head of the queue and runs them immediately. This gets higher RX throughput with the SDIO bus. This was originally submitted as [1]. The original author Wright Feng reports > throughput result with 43455(11ac) on 1 core 1.6 Ghz platform is > Without WQ_HIGGPRI TX/RX: 293/301 (mbps) > With WQ_HIGHPRI TX/RX: 293/321 (mbps) I tested this with a 43364(11bgn) on a 1 core 800 MHz platform and got Without WQ_HIGHPRI TX/RX: 16/19 (Mbits/sec) With WQ_HIGHPRI TX/RX: 24/20 (MBits/sec) [1] https://lore.kernel.org/linux-wireless/1584604406-15452-4-git-send-email-wright.feng@cypress.com/Signed-off-by:Sean Anderson <sean.anderson@seco.com> Reviewed-by:
Arend van Spriel <aspriel@gmail.com> Signed-off-by:
-
Mikhail Rudenko authored
A separate firmware is needed for Broadcom 43430 revision 2. This chip can be found in e.g. certain revisions of Ampak AP6212 wireless IC. Original firmware file from IC vendor is named 'fw_bcm43436b0.bin', but brcmfmac and also btbcm drivers report chip id 43430, so requested firmware file name is 'brcmfmac43430b0-sdio.bin' in line with other 43430 revisions. Reviewed-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Mikhail Rudenko <mike.rudenko@gmail.com> Signed-off-by:
-
Arend van Spriel authored
Historically the broadcom wifi chipsets always had enumeration space containing all core information at same place. However, for new chipsets the ASIC developers moved away from that given fact. So we have to accommodate that it can differ per chipset. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
Newer firmware API require commands to use xtlv format. Add support for that in the firmware interface layer. Reviewed-by:
-
Arend van Spriel authored
Some cores are getting a revision greater that 99 thus messing up the column alignment in the list of cores. So adding a digit for the core revision. Reviewed-by:
-
Arend van Spriel authored
The function brcmf_chip_tcm_rambase() returns 0 as invalid ram base address. However, upcoming chips have ram base address starting at zero so we have to find a more appropriate invalid value to return. Reviewed-by:
-
Linus Walleij authored
The patch that would first try the board-specific firmware had a bug because the fallback would not be called: the asynchronous interface is used meaning request_firmware_nowait() returns 0 immediately. Harden the firmware loading like this: - If we cannot build an alt_path (like if no board_type is specified) just request the first firmware without any suffix, like in the past. - If the lookup of a board specific firmware fails, we get a NULL fw in the async callback, so just try again without the alt_path from a dedicated brcm_fw_request_done_alt_path callback. - Drop the unnecessary prototype of brcm_fw_request_done. - Added MODULE_FIRMWARE match for per-board SDIO bins, making userspace tools to pull all the relevant firmware files. Fixes: 5ff01391 ("brcmfmac: firmware: Allow per-board firmware binaries") Cc: Stefan Hansson <newbyte@disroot.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Reviewed-by:
-
- 06 Aug, 2021 1 commit
-
-
Lukas Bulwahn authored
Commit 1d89cae1 ("MAINTAINERS: mark prism54 obsolete") indicated the prism54 driver as obsolete in July 2010. Now, after being exposed for ten years to refactoring, general tree-wide changes and various janitor clean-up, it is really time to delete the driver for good. This was discovered as part of a checkpatch evaluation, investigating all reports of checkpatch's WARNING:OBSOLETE check. p54 replaces prism54 so users should be unaffected. There was a one off chipset someone long ago reported that p54 didn't work with but the reporter never followed up on that. Additionally, distributions have been blacklisting prism54 for years now. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Acked-by:
Luis Chamberlain <mcgrof@kernel.org> Signed-off-by:
-
- 01 Aug, 2021 2 commits
-
-
dingsenjie authored
The label is only used once, so we delete it and use the return statement instead of the goto statement. Signed-off-by:
dingsenjie <dingsenjie@yulong.com> Signed-off-by:
-
Linus Walleij authored
After some crashes in the 3D engine (!) on the Samsung GT-I8530 it turns out that the main firmware file can be device dependent, something that was previously only handled for the NVRAM parameter file. Rewrite the code a bit so we can a per-board suffixed firmware binary as well, if this does not exist we fall back to the canonical firmware name. Example: a 4330 device with the OF board compatible is "samsung,gavini". We will first try "brcmfmac4330-sdio.samsung,gavini.bin" then "brcmfmac4330-sdio.bin" if that does not work. Cc: phone-devel@vger.kernel.org Cc: newbyte@disroot.org Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
-
- 28 Jul, 2021 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.15. Major changes: ath5k, ath9k, ath10k, ath11k: * switch from 'pci_' to 'dma_' API
-
- 26 Jul, 2021 6 commits
-
-
Jason Wang authored
The dma_pool_zalloc combines dma_pool_alloc/memset. Therefore, the dma_pool_alloc/memset can be replaced with dma_pool_zalloc which is more compact. Signed-off-by:
Jason Wang <wangborong@cdjrlc.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yinjun Zhang authored
Use dynamic interrupt moderation library to implement coalesce adaptive feature for nfp driver. Signed-off-by:
Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by:
Yu Xiao <yu.xiao@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Richard Laing authored
Packets are aggregated over the MBIM link and currently the MHI net device will count each aggregated packet rather then the actual packets themselves. If a protocol handler module is specified, use that to count the packets rather than directly in the MHI net device. This is in line with the behaviour of the USB net cdc_mbim driver. Signed-off-by:
Richard Laing <richard.laing@alliedtelesis.co.nz> Signed-off-by:
-
wengjianfeng authored
Simplify the code by removing unnecessary label and returning directly. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: add support devlink This series adds devlink support for the HNS3 ethernet driver. change log: V2 -> V3: 1. remove two patches of setting rx/tx buffer size by devlink param. V1 -> V2: 1. add more detailed descriptions of parameters in document hns3.rst. RFC -> V1: 1. use DEVLINK_INFO_VERSION_GENERIC_FW instead of "fw-version". 2. add devlink documentation for hns3 driver. ==================== Signed-off-by: -
Hao Chen authored
Add devlink reload support for HNS3 ethernet VF driver. Signed-off-by:
Hao Chen <chenhao288@hisilicon.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
