Maxim TCPC has additional ADCs and low current(1ua) current source
to measure the impedance of CC and SBU pins. When tcpm invokes
the check_contaminant callback, Maxim TCPC measures the impedance
of the CC & SBU pins and when the impedance measured is less than
1MOhm, it is assumed that USB-C port is contaminated. CC comparators
are also checked to differentiate between presence of sink and
contaminant. Once USB-C is deemed to be contaminated, MAXIM TCPC
has additional hardware to disable normal DRP toggling cycle and
enable 1ua on CC pins once every 2.4secs/4.8secs. Maxim TCPC
interrupts AP once the impedance on the CC pin is above the
1MOhm threshold. The Maxim tcpc driver then signals TCPM_PORT_CLEAN
to restart toggling.

Renaming tcpci_maxim.c to tcpci_maxim_core.c and moving reg read/write
helper functions to the tcpci_maxim.h header file.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230114093246.1933321-3-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This change adds callback to evaluate presence of contaminant in
the TCPCI layer.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20230114093246.1933321-2-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On some of the TCPC implementations, when the Type-C port is exposed
to contaminants, such as water, TCPC stops toggling while reporting OPEN
either by the time TCPM reads CC pin status or during CC debounce
window. This causes TCPM to be stuck in TOGGLING state. If TCPM is made
to restart toggling, the behavior recurs causing redundant CPU wakeups
till the USB-C port is free of contaminant.

[206199.287817] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[206199.640337] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[206199.985789] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]

(or)

[ 7853.867577] Start toggling
[ 7853.889921] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7855.698765] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 7855.698790] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7855.698826] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 7855.703559] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected]
[ 7855.856555] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 7855.856581] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7855.856613] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @ 170 ms [rev3 NONE_AMS]
[ 7856.027744] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 170 ms]
[ 7856.181949] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7856.187896] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7857.645630] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7857.647291] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 7857.647298] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7857.647310] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 7857.808106] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 7857.808123] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7857.808150] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @ 170 ms [rev3 NONE_AMS]
[ 7857.978727] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 170 ms]

To mitigate redundant TCPM wakeups, TCPCs which do have the needed hardware
can implement the check_contaminant callback which is invoked by TCPM
to evaluate for presence of contaminant. Lower level TCPC driver can
restart toggling through TCPM_PORT_CLEAN event when the driver detects
that USB-C port is free of contaminant. check_contaminant callback also
passes the disconnect_while_debounce flag which when true denotes that
the CC pins transitioned to OPEN state during the CC debounce window.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230114093246.1933321-1-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since ports can have retimers associated with them, update the Type-C
alternate mode bus code to also set retimer state when the switch state
is updated.

While we are here, make the typec_retimer_dev_type declaration in the
retimer.h file as extern, so that the header file can be successfully
included in the bus code without redeclaration compilation errors.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230112221609.540754-4-pmalani@chromium.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a wrapper that calls the set() function for various switches
associated with a port altmode.

Right now, it just wraps the existing typec_mux_set() command,
but it can be expanded to include other switches in future patches.

No functional changes introduced by this patch.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230112221609.540754-3-pmalani@chromium.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just like it does with muxes, the Type-C bus code can update the state
of connected retimers (especially when altmode-related transitions
occur). Add a retimer handle to the port altmode struct to enable this.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230112221609.540754-2-pmalani@chromium.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Program USB2 pad PD controls during port connect/disconnect, port
suspend/resume, and test mode, to reduce power consumption on
disconnect or suspend.
Signed-off-by: Petlozu Pravareshwar <petlozup@nvidia.com>
Co-developed-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221111101813.32482-4-jilin@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

XHCI host drivers may override the default xhci_hub_control() with
their own device specific function. To allow these host drivers to
call the xhci_hub_control() function from within their own
hub_control() callback and be built as a module, export the symbol
for xhci_hub_control.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221111101813.32482-3-jilin@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a hub_control() callback to the xhci_driver_overrides structure to
allow host drivers to override the default hub_control function. This
is required for Tegra which requires device specific actions for power
management to be executed during USB state transitions.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221111101813.32482-2-jilin@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This change adds Tegra234 XUSB host mode controller support.

In Tegra234, some of the registers have moved to bar2 space.
The new soc variable has_bar2 indicates the chip with bar2
area. This patch adds new reg helper to let the driver reuse
the same code for those chips with bar2 support.
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Co-developed-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-7-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the XUSB pad controller found on Tegra234 SoCs. It is
mostly similar to the same IP found on Tegra194, because most of
the Tegra234 XUSB PADCTL registers definition and programming sequence
are the same as Tegra194, Tegra234 XUSB PADCTL can share the same
driver with Tegra186 and Tegra194 XUSB PADCTL.

Introduce a new feature, USB2 HW tracking, for Tegra234.
The feature is to enable HW periodical PAD tracking which measure
and capture the electric parameters of USB2.0 PAD.
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Co-developed-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-6-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pad tracking is a one-time calibration for Tegra186 and Tegra194.
Clk should be disabled after calibration.

Disable clk after calibration.
While at it add 100us delay for HW recording the calibration value.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-5-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit enables XUSB host and pad controller on Jetson AGX Orin.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230111110450.24617-4-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device-tree binding documentation for the XUSB host controller present
on Tegra234 SoC. This controller supports the USB 3.1 specification.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230111110450.24617-2-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Color matching attributes in the configfs for UVC are named with the
phrase "default". The implication of that is that they will only be
used _with_ the default color matching descriptor, and that will
shortly no longer be the case.

Remove the "default" from the color matching descriptor attribute
variables.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20221213083736.2284536-2-dan.scally@ideasonboard.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB controllers in the i.MX8MP are located inside the HSIO
power domain. Add the power-domains property to the DT binding
to be able to describe the hardware properly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230110180804.594462-1-l.stach@pengutronix.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable wakeup when pluging or unpluging USB cable. It is up to other
components to hold system in active mode, such as display, so that
user can receive the notification.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230105075058.924680-2-jun.nie@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add wakeup property description. People can enable it with adding
the property.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230105075058.924680-1-jun.nie@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic at
once.

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20230106152828.3790902-1-gregkh@linuxfoundation.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After contributing the driver, add myself as the maintainer
for Renesas RZ/N1 USBF controller.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-6-herve.codina@bootlin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the USBF controller available in the r9a06g032 SoC.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-5-herve.codina@bootlin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the Renesas USBF controller.
This controller is an USB2.0 UDC controller available in the
Renesas r9a06g032 SoC (RZ/N1 family).
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230105152257.310642-4-herve.codina@bootlin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The CFG_USB[H2MODE] allows to switch the USB configuration. The
configuration supported are:
  - One host and one device
or
  - Two hosts

Set CFG_USB[H2MODE] based on the USBF controller (USB device)
availability.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-3-herve.codina@bootlin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Renesas RZ/N1 USBF controller is an USB2.0 device controller
(UDC) available in the Renesas r9a06g032 SoC (RZ/N1 family).
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-2-herve.codina@bootlin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to call acpi_dev_present() followed by
acpi_dev_get_first_match_dev() as they both do the same
with only difference in the returning value. Instead,
call the latter and check its result.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230102202933.15968-2-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When acpi_dev_get_memory_resources() fails, the reference count is
left bumped. Drop it as it's done in the other error paths.

Fixes: 43d596e3 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230102202933.15968-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Under resource constraints, this interrupt may use other interrupt line
or this interrupt line may be shared with other devices as long as they
meet the sharing requirements. Besides, This irq flag will not cause other
side effect if tcpci driver is the only user.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221214022334.2520677-1-xu.yang_2@nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add fsl,imx8mm-usbmisc compatible for i.MX8MM
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221223031012.92932-2-peng.fan@oss.nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add fsl,imx8mm-usb compatible for i.MX8MM
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221223031012.92932-1-peng.fan@oss.nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Document the transfer buffer requirement. That is, the buffer must be
DMAble - otherwise data corruption might occur.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221220-usb-dmadoc-v4-0-74a045bf14f4@chromium.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The notification call chain should be registered after the device gets
ready. Otherwise, we  might get errors when setting data roles in an
incomplete system.

This patch refactors update data role work and register the notifier
call chain after the system gets ready.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20221216042026.98517-1-haotienh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some platforms(for eg: RZ/V2M EVK) does not have interrupt pin
connected to HD3SS3220. Add polling support for role detection.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221209171836.71610-3-biju.das.jz@bp.renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On some platforms(for eg: RZ/V2M EVK), interrupt is not populated. Update
the binding to make interrupt property as optional.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221209171836.71610-2-biju.das.jz@bp.renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull powerpc fixes from Michael Ellerman:

 - Three fixes for various bogosity in our linker script, revealed
   by the recent commit which changed discard behaviour with some
   toolchains.

* tag 'powerpc-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/vmlinux.lds: Don't discard .comment
  powerpc/vmlinux.lds: Don't discard .rela* for relocatable builds
  powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT

Pull memblock fixes from Mike Rapoport:
 "Small fixes in kernel-doc and tests:

   - Fix kernel-doc for memblock_phys_free() to use correct names for
     the counterpart allocation methods

   - Fix compilation error in memblock tests"

* tag 'fixes-2023-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
  memblock: Fix doc for memblock_phys_free
  memblock tests: Fix compilation error.

Pull NFS client fixes from Trond Myklebust:

 - Fix a race in the RPCSEC_GSS upcall code that causes hung RPC calls

 - Fix a broken coalescing test in the pNFS file layout driver

 - Ensure that the access cache rcu path also applies the login test

 - Fix up for a sparse warning

* tag 'nfs-for-6.2-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: Fix up a sparse warning
  NFS: Judge the file access cache's timestamp in rcu path
  pNFS/filelayout: Fix coalescing test for single DS
  SUNRPC: ensure the matching upcall is in-flight upon downcall

Pull cifs fixes from Steve French:
 "cifs/smb3 client fixes:

   - two multichannel fixes

   - three reconnect fixes

   - unmap fix"

* tag '6.2-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix interface count calculation during refresh
  cifs: refcount only the selected iface during interface update
  cifs: protect access of TCP_Server_Info::{dstaddr,hostname}
  cifs: fix race in assemble_neg_contexts()
  cifs: ignore ipc reconnect failures during dfs failover
  cifs: Fix kmap_local_page() unmapping

Pull devicetree fixes from Rob Herring:

 - Fix DT memory scanning for some MIPS boards when memory is not
   specified in DT

 - Redo CONFIG_CMDLINE* handling for missing /chosen node. The first
   attempt broke PS3 (and possibly other PPC platforms).

 - Fix constraints in QCom Soundwire schema

* tag 'devicetree-fixes-for-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: fdt: Honor CONFIG_CMDLINE* even without /chosen node, take 2
  Revert "of: fdt: Honor CONFIG_CMDLINE* even without /chosen node"
  dt-bindings: soundwire: qcom,soundwire: correct sizes related to number of ports
  of/fdt: run soc memory setup when early_init_dt_scan_memory fails