Disabling the adapter after each transfer adds additional delays
for each I2C transfer. Even if we don't wait for it to be disabled
anymore, on next transfer we will need to if we have several transfers
in a row.

Now during the transfer init we check if IC_TAR can be changed
dynamically, the status register for no activity and TX buffer being
empty. In this case we don't need to disable it

When a transfer fails the adapter will still be disabled - this is a
conservative approach. When transfers succeed, the adapter is left
enabled and it's configured so to disable interrupts.

Alternating register reads on 2 slaves:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00

Before:
	8.638705161 seconds time elapsed                  ( +-  5.90% )
After:
	7.516821591 seconds time elapsed                  ( +-  0.11% )
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This adapter can be synthesized with dynamic tar update enabled or disabled.
When enabled it is not necessary to disable the adapter to change the slave
address in some situations, which saves some time per transaction.

There is no direct register to know if this feature is enabled but we can do it
indirectly by writing to the 10BIT_ADDR field in IC_CON: this field is
read only when dynamic tar update is enabled.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

These are used in 2 places and will be needed in more.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If we aren't going to continue using the controller we can just disable
it instead of waiting for it to complete. The biggest improvement here
is when a I2C transaction is completed and it doesn't block until
the adapter is disabled. When a new transfer is needed we will disable
and wait for its completion.

This way the adapter will continue changing its state in parallel to the
execution of the thread that requested the I2C transaction saving most
of the time 25~250 usec per I2C transaction.

A simple program doing a register read (1 byte write, 1 byte read)
alternating on 2 different slaves repeated 25k times for each and
measurements taken 4 times we get:

perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00

Before:
	30.879317977 seconds time elapsed                 ( +- 14.83% )
After:
	8.638705161 seconds time elapsed                  ( +-  5.90% )
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fast mode is the default speed of i2c-designware which can be overridden
by platform data or by "clock-frequency" device property. Even though
the ACPI 5.1 can pass device properties via _DSD method, shipping systems
define the connection speed between I2C host and each slave in their
I2cSerialBus resources. Which means speed is not defined per bus but per
slave.

As there is now support in i2c-core to find the bus speed from ACPI use
that to set up the bus speed prior registering the I2C adapter.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptor which define each controller-slave
connection define the maximum speed supported by that connection.

Thus finding the maximum safe speed for the bus is to walk through all
I2cSerialBus resources that are associated to I2C controller and use the
speed of slowest connection.

Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.

This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does communication.

Previous version commit 55d38d06 ("i2c: core: Add function for finding
the bus speed from ACPI") got reverted due merge conflicts from
commit 525e6fab ("i2c / ACPI: add support for ACPI reconfigure
notifications").

This version is a bit bigger than previous version but is still sharing
the lowest and complicated part of I2cSerialBus lookup routines with the
existing code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.

Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.

This is updated version from commit a7003b65 ("i2c: core: Cleanup I2C
ACPI namespace") that got reverted due merge conflicts from
commit 525e6fab ("i2c / ACPI: add support for ACPI reconfigure
notifications").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch enabled high speed mode. High speed mode can be turn on by
setting the clk_freq to 3400000. High speed HCNT and LCNT are needed
as there is no default value provided.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

DW_IC_CON_MASTER, DW_IC_CON_SLAVE_DISABLE and DW_IC_CON_RESTART_EN are
common config that need to be set for i2c designware master. So, configure
it first without having to repeat inside the if else.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch enabled fast mode plus. The fast mode plus and fast speed
share the same HCNT and LCNT register. So, the fast mode plus will only
run when the HCNT and LCNT value is provided. Else, it will run at fast
speed as default.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2C designware controller can run at fast mode plus and high speed. This
patch adds the capability to get the HCNT, LCNT configuration via
FPCN (fast plus) and HSCN (high speed) ACPI method.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2c designware controller operate speed is configured in the register
IC_CON. Previously the operate speed is determined by a local variable
clk_freq. This patch will move the local variable clk_freq into struct
dw_i2c_dev. This change will ease the set and get of the clk_freq.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The i2c Octeon and ThunderX drivers are maintained by Cavium.
While at it fix the whitespace errors of the next entry.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Initialize booleon values with true instead of 1.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Sort include files alphabetically to reduce probability of merge
conflicts.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The register offsets are different between Octeon and ThunderX so move
them into the algorithm struct and get rid of the define.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add SMBUS alert interrupt support. For now only device tree is
supported for specifying the alert. In case of ACPI an error
is returned.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The ThunderX SOC uses the same i2c block as the Octeon SOC.
The main difference is that on ThunderX the device is a PCI device
so device probing is done via PCI, interrupts are MSI-X. The
clock rates can be set via device tree or ACPI.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Move common functionality into a separate file in preparation of the
re-use from the ThunderX i2c driver.

Functions are slightly re-ordered but no other changes are included.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This is an intermediate commit in preparation of the driver split.
The module rename in this commit will be reverted in the next patch,
this is just done to make the series bisectible.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This unifies usage with i2c_lock_bus and i2c_unlock_bus, and paves the
way for the next patch which looks a bit saner with this preparatory
work taken care of beforehand.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The at24 driver doesn't check if the chip is functional in its probe
function. This leads to instantiating devices that are not physically
present. For example the cape EEPROMs for BeagleBone Black are defined
in the device tree at four addresses on i2c2, but normally only one of
them is present.

If the userspace doesn't know the location in advance, it will need to
check if reading the nvmem attributes fails to determine which EEPROM
is actually there.

Try to read a single byte in probe() and bail-out with -ENODEV if the
read fails.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull two parisc fixes from Helge Deller:
 "The first patch ensures that the high-res cr16 clocksource (which was
  added in kernel 4.7) gets choosen as default clocksource for parisc.

  The second patch moves the #define of EREFUSED down inside errno.h and
  thus unbreaks building the gccgo compiler"

* 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix order of EREFUSED define in errno.h
  parisc: Fix automatic selection of cr16 clocksource

This is an entirely new driver instead of yet another set of patches
to sb_edac.c because:

1) Mapping from PCI devices to socket/memory controller is significantly
   different. Skylake scatters devices on a socket across a number of
   PCI buses.
2) There is an extra level of interleaving via the "mcroute" register
   that would be a little messy to squeeze into the old driver.
3) Validation is getting too expensive. Changes to sb_edac need to
   be checked against Sandy Bridge, Ivy Bridge, Haswell, Broadwell and
   Knights Landing.
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.

Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.

Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org

Commit 54b66800 (parisc: Add native high-resolution sched_clock()
implementation) added support to use the CPU-internal cr16 counters as reliable
clocksource with the help of HAVE_UNSTABLE_SCHED_CLOCK.

Sadly the commit missed to remove the hack which prevented cr16 to become the
default clocksource even on SMP systems.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.7+

The kernel test robot reported a usercopy failure in the new hardened
sanity checks, due to a page-crossing copy of the FPU state into the
task structure.

This happened because the kernel test robot was testing with SLOB, which
doesn't actually do the required book-keeping for slab allocations, and
as a result the hardening code didn't realize that the task struct
allocation was one single allocation - and the sanity checks fail.

Since SLOB doesn't even claim to support hardening (and you really
shouldn't use it), the straightforward solution is to just make the
usercopy hardening code depend on the allocator supporting it.
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull i2c fixes from Wolfram Sang:
 "I2C has some pretty standard driver bugfixes and one minor cleanup"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: meson: Use complete() instead of complete_all()
  i2c: brcmstb: Use complete() instead of complete_all()
  i2c: bcm-kona: Use complete() instead of complete_all()
  i2c: bcm-iproc: Use complete() instead of complete_all()
  i2c: at91: fix support of the "alternative command" feature
  i2c: ocores: add missed clk_disable_unprepare() on failure paths
  i2c: cros-ec-tunnel: Fix usage of cros_ec_cmd_xfer()
  i2c: mux: demux-pinctrl: properly roll back when adding adapter fails

Pull device mapper fixes from Mike Snitzer:

 - a stable fix for DM round robin multipath path selector to disable
   preemption before using this_cpu_ptr()

 - a slight increase in DM crypt's mempool reserves to make swap ontop
   of DM crypt more performant

 - a few DM raid fixes to issues found while testing changes that were
   merged in v4.8-rc1

* tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm raid: support raid0 with missing metadata devices
  dm raid: enhance attempt_restore_of_faulty_devices() to support more devices
  dm raid: fix restoring of failed devices regression
  dm raid: fix frozen recovery regression
  dm crypt: increase mempool reserve to better support swapping
  dm round robin: do not use this_cpu_ptr() without having preemption disabled

Pull SCSI fixes from James Bottomley:
 "Six fairly small fixes.  The ipr, mpt3sas and ses ones all trigger
  oopses.  The megaraid one fixes an attach failure on io mapped only
  cards, the fcoe one is an obvious problem in the error path and the
  aacraid one is a theoretical security issue (ability to trick the
  kernel into a buffer overrun)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  ses: Fix racy cleanup of /sys in remove_dev()
  mpt3sas: Fix resume on WarpDrive flash cards
  ipr: Fix sync scsi scan
  megaraid_sas: Fix probing cards without io port
  aacraid: Check size values after double-fetch from user
  fcoe: Use kfree_skb() instead of kfree()

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for reported issues for your tree.

  The normal amount of gadget fixes, xhci fixes, new device ids, and a
  few other minor things.  All of them have been in linux-next for a
  while, the full details are in the shortlog below"

* tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
  xhci: don't dereference a xhci member after removing xhci
  usb: xhci: Fix panic if disconnect
  xhci: really enqueue zero length TRBs.
  xhci: always handle "Command Ring Stopped" events
  cdc-acm: fix wrong pipe type on rx interrupt xfers
  usb: misc: usbtest: add fix for driver hang
  usb: dwc3: gadget: stop processing on HWO set
  usb: dwc3: don't set last bit for ISOC endpoints
  usb: gadget: rndis: free response queue during REMOTE_NDIS_RESET_MSG
  usb: udc: core: fix error handling
  usb: gadget: fsl_qe_udc: off by one in setup_received_handle()
  usb/gadget: fix gadgetfs aio support.
  usb: gadget: composite: Fix return value in case of error
  usb: gadget: uvc: Fix return value in case of error
  usb: gadget: fix check in sync read from ep in gadgetfs
  usb: misc: usbtest: usbtest_do_ioctl may return positive integer
  usb: dwc3: fix missing platform_set_drvdata() in dwc3_of_simple_probe()
  usb: phy: omap-otg: Fix missing platform_set_drvdata() in omap_otg_probe()
  usb: gadget: configfs: add mutex lock before unregister gadget
  usb: gadget: u_ether: fix dereference after null check coverify warning
  ...

Merge tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs

Pull xfs and iomap fixes from Dave Chinner:
 "Changes in this update:

  Regression fixes for XFS changes introduce in 4.8-rc1:
   - buffer IO accounting assert failure
   - ENOSPC block accounting reservation issue
   - DAX IO path page cache invalidation fix
   - rmapbt on-disk block count in agf
   - correct classification of rmap block type when updating AGFL.
   - iomap support for attribute fork mapping

  Regression fixes for iomap infrastructure in 4.8-rc1:
   - fiemap: honor FIEMAP_FLAG_SYNC
   - fiemap: implement FIEMAP_FLAG_XATTR support to fix XFS regression
   - make mark_page_accessed and pagefault_disable usage consistent with
     other IO paths"

* tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
  xfs: remove OWN_AG rmap when allocating a block from the AGFL
  xfs: (re-)implement FIEMAP_FLAG_XATTR
  xfs: simplify xfs_file_iomap_begin
  iomap: mark ->iomap_end as optional
  iomap: prepare iomap_fiemap for attribute mappings
  iomap: fiemap should honor the FIEMAP_FLAG_SYNC flag
  iomap: remove superflous pagefault_disable from iomap_write_actor
  iomap: remove superflous mark_page_accessed from iomap_write_actor
  xfs: store rmapbt block count in the AGF
  xfs: don't invalidate whole file on DAX read/write
  xfs: fix bogus space reservation in xfs_iomap_write_allocate
  xfs: don't assert fail on non-async buffers on ioacct decrement

Merge tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fix a bug in it87 driver and URLs in ftsteutates driver"

* tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (ftsteutates) Correct ftp urls in driver documentation
  hwmon: (it87) Features mask must be 32 bit wide

Pull more drm fixes from Dave Airlie:
 "Daniel pointed out I'd missed some i915 fixes, and I also found a
  single etnaviv fix I missed.

  So here they are"

* tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux:
  drm/etnaviv: take GPU lock later in the submit process
  drm/i915: Fix modeset handling during gpu reset, v5.
  drm/i915: fix aliasing_ppgtt leak
  drm/i915: fix WaInsertDummyPushConstPs
  drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
  drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
  drm/i915: Acquire audio powerwell for HD-Audio registers
  drm/i915: Add missing rpm wakelock to GGTT pread
  drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
  drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
  drm/i915: Program iboost settings for HDMI/DVI on SKL
  drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
  drm/i915: Handle ENOSPC after failing to insert a mappable node
  drm/i915: Flush GT idle status upon reset

Pull DeviceTree fixes from Rob Herring:

 - a couple of DT node ref counting fixes

 - fix __unflatten_device_tree for PPC PCI hotplug case

 - rework marking irq controllers as OF_POPULATED in cases where real
   driver is used.

 - disable of_platform_default_populate_init on PPC.  The change in
   initcall order causes problems which need to be sorted out later.

* tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: fix reference counting in of_graph_get_endpoint_by_regs
  of/platform: disable the of_platform_default_populate_init() for all the ppc boards
  ARM: imx6: mark GPC node as not populated after irq init to probe pm domain driver
  of/irq: Mark interrupt controllers as populated before initialisation
  drivers/of: Validate device node in __unflatten_device_tree()
  of: Delete an unnecessary check before the function call "of_node_put"

Pull documentation fixes from Jonathan Corbet:
 "Three small fixes for Sphinx-formatted documentation generation"

* tag '4.8-doc-fixes' of git://git.lwn.net/linux:
  doc-rst: customize RTD theme, drop padding of inline literal
  docs: kernel-documentation: remove some highlight directives
  docs: Set the Sphinx default highlight language to "guess"

Collection of i915 fixes.

* tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Fix modeset handling during gpu reset, v5.
  drm/i915: fix aliasing_ppgtt leak
  drm/i915: fix WaInsertDummyPushConstPs
  drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
  drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
  drm/i915: Acquire audio powerwell for HD-Audio registers
  drm/i915: Add missing rpm wakelock to GGTT pread
  drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
  drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
  drm/i915: Program iboost settings for HDMI/DVI on SKL
  drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
  drm/i915: Handle ENOSPC after failing to insert a mappable node
  drm/i915: Flush GT idle status upon reset