When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.

The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.

It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.

I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.

Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Applied common sense, no info from the manufacturer:

(0x8516, 0x2070) is RT2070
(0x8516, 0x2770) is RT2770
(0x8516, 0x2870) is RT2870
[...]
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

One HT debugging printk is missing a newline,
add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Orinoco should be endian clean, so enable the checking.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of using a local function.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

... to set fragmentation and RTS thresholds. Also report RTS retry
settings during wiphy init.

Note that the existing semantics for enabling microwave robustness are
preserved on firmwares that have it.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.

Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.

Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Kalle reported that his system deadlocks since my
recent work in this area. The reason quickly became
apparent: we try to cancel_timer_sync() a timer
from within itself. Fix that by making the function
aware of the context it is called from.
Reported-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The flag is called IEEE80211_TX_STAT_AMPDU rather than using the whole word
STATUS.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

Some future hardware will also require some antenna
overrides so make the current logic more generic;
right now it is semantically based on a workaround
for off-channel reception but the reasons for the
new antenna overrides will be different.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Off-channel reception is acceptable in monitor
mode, and checking for monitor mode this way is
not really correct anyway since it could be the
case while operating.

Now iwl_is_monitor_mode() is no longer used so
remove it completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Monitor mode operation need not (and probably should
not) affect scanning this way since real monitoring
can not properly happen while scanning anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The flag name is a little misleading, this
flag instructs the device to ignore bluetooth
messages for purposes of frame transmissions,
so rename the flag to TX_CMD_FLG_IGNORE_BT.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Some future hardware will require a different command to
be sent for bluetooth coexist, so make this a virtual
method that can be changed on a per-device basis.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Since multiple new devices having similar uCode architecture and use same
registers address, remove more reference to 5000 series to eliminate the
confusion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Perform sanity check for turn on aggregation tid. Also remove the
option for turn on all the aggregation tids at once since it is
deprecated function and not being used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

For 6000g2 series of NICs, PA type is determined by uCode, driver do not
have to set the register for internal/external PA. It is a workaround
just for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Add hardware revision for 6000g2 series of NIC
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This function is called twice in a row, remove the second one.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Seperate debugfs functions into iwlagn specific
debugfs file and Add debugfs ops to iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Use the show uCode statistics function for uCode debugging purposes only; it
is being duplicated in both debugfs and sysfs. remove the one from sysfs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This patch is to bring up 6000 Series 2x2 AGN Gen2 adapters.
Seperate various version numbers from 6000 Series definitions;
Add module firmware declaration for the new adapters;
Add additional device IDs and subsystem IDs;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Some definition for eeprom apply to more than 5000 series device, change
the name to reflect it for easy reading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Scan requesting doesn't need to be asynchronous
since all code paths leading up to it can sleep.
Make the scan request a new util operation that
is hw-specific (to account for 3945 vs. agn)
and call it right in place.

This patch moves a lot of code into iwlagn as
it need not be in iwlcore.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

I keep checking what "priv->scan" is, so rename
it to "priv->scan_cmd" which more clearly tells
us what it is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Since we no longer do a multi-pass scan,
keeping track of how long each pass took
is pointless since there will only be one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

This logic is just confusing, if anything it
belongs into mac80211. Also, even if we do
scan during the EAPOL handshake, that will
not cause any problems, just a short delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

With atomic bitops, test_and_{set,clear}_bit
should be used instead of separate test_bit
and set_bit/clear_bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Since mac80211 will now never request scanning
multiple bands, we can remove all the associated
logic and scan a single band only in each scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Even the initial single/dual stream values will be overridden later when
issue link quality command; but still make sense not to use hard-code
value during initialization. Single/Dual stream mask are used to indicate the
best antenna for SISO/MIMO; different NIC has different tx antenna
configuration; so the parameter need to based on the valid tx antenna.

1x2 device: single tx antenna available, only SISO is valid
configuration, but still need to set up MIMO configuration, so set it up
with antenna A & B as default.
2x2 device: two tx antenna available, dual_stream will use both valid
antenna.

3x3 device: three tx antenna available, skip the first antenna and
choice the second and third antenna for dual_stream.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-6000.c

For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.

Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported

And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwl_wimax_coex_cmd.flags can be really uninitialized, so fix
that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In mac80211 we always check both scan_req->ie and scan_req->ie_len
against zero before usage, in iwlwifi we should do the same.

Remove not needed "left -= ie_len" while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.

Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bunch of endian issues that
were exposed by sparse. It's a miracle that the driver
worked at all till now.

The Lord be praised.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a WMI command has timed out for some reason,
a late WMI response would end up updating the
response region of a new WMI request that has been
issued in the meantime.

Fix this race condition by dropping a WMI response
if a new WMI command has been issued.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>