- 17 Jun, 2017 4 commits
-
-
Richard authored
commit 22322035 upstream. The code in block/partitions/msdos.c recognizes FreeBSD, OpenBSD and NetBSD partitions and does a reasonable job picking out OpenBSD and NetBSD UFS subpartitions. But for FreeBSD the subpartitions are always "bad". Kernel: <bsd:bad subpartition - ignored Though all 3 of these BSD systems use UFS as a file system, only FreeBSD uses relative start addresses in the subpartition declarations. The following patch fixes this for FreeBSD partitions and leaves the code for OpenBSD and NetBSD intact: Signed-off-by:
Richard Narron <comet.berkeley@gmail.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Imre Deak authored
commit 6ab92afc upstream. Since commit bac2a909 Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Date: Wed Jan 21 02:17:42 2015 +0100 PCI / PM: Avoid resuming PCI devices during system suspend PCI devices will default to allowing the system suspend complete optimization where devices are not woken up during system suspend if they were already runtime suspended. This however breaks the i915/HDA drivers for two reasons: - The i915 driver has system suspend specific steps that it needs to run, that bring the device to a different state than its runtime suspended state. - The HDA driver's suspend handler requires power that it will request from the i915 driver's power domain handler. This in turn requires the i915 driver to runtime resume itself, but this won't be possible if the suspend complete optimization is in effect: in this case the i915 runtime PM is disabled and trying to get an RPM reference returns -EACCESS. Solve this by requiring the PCI/PM core to resume the device during system suspend which in effect disables the suspend complete optimization. Regardless of the above commit the optimization stayed disabled for DRM devices until commit d14d2a84 Author: Lukas Wunner <lukas@wunner.de> Date: Wed Jun 8 12:49:29 2016 +0200 drm: Remove dev_pm_ops from drm_class so this patch is in practice a fix for this commit. Another reason for the bug staying hidden for so long is that the optimization for a device is disabled if it's disabled for any of its children devices. i915 may have a backlight device as its child which doesn't support runtime PM and so doesn't allow the optimization either. So if this backlight device got registered the bug stayed hidden. Credits to Marta, Tomi and David who enabled pstore logging, that caught one instance of this issue across a suspend/ resume-to-ram and Ville who rememberd that the optimization was enabled for some devices at one point. The first WARN triggered by the problem: [ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746448] pm_runtime_get_sync() failed: -13 [ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_ numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915] [ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1 [ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017 [ 6250.746521] Workqueue: events_unbound async_run_entry_fn [ 6250.746525] Call Trace: [ 6250.746530] dump_stack+0x67/0x92 [ 6250.746536] __warn+0xc6/0xe0 [ 6250.746542] ? pci_restore_standard_config+0x40/0x40 [ 6250.746546] warn_slowpath_fmt+0x46/0x50 [ 6250.746553] ? __pm_runtime_resume+0x56/0x80 [ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746610] intel_display_power_get+0x1b/0x40 [i915] [ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915] [ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core] [ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel] [ 6250.746667] pci_pm_runtime_resume+0x76/0xa0 [ 6250.746672] __rpm_callback+0xb4/0x1f0 [ 6250.746677] ? pci_restore_standard_config+0x40/0x40 [ 6250.746682] rpm_callback+0x1f/0x80 [ 6250.746686] ? pci_restore_standard_config+0x40/0x40 [ 6250.746690] rpm_resume+0x4ba/0x740 [ 6250.746698] __pm_runtime_resume+0x49/0x80 [ 6250.746703] pci_pm_suspend+0x57/0x140 [ 6250.746709] dpm_run_callback+0x6f/0x330 [ 6250.746713] ? pci_pm_freeze+0xe0/0xe0 [ 6250.746718] __device_suspend+0xf9/0x370 [ 6250.746724] ? dpm_watchdog_set+0x60/0x60 [ 6250.746730] async_suspend+0x1a/0x90 [ 6250.746735] async_run_entry_fn+0x34/0x160 [ 6250.746741] process_one_work+0x1f2/0x6d0 [ 6250.746749] worker_thread+0x49/0x4a0 [ 6250.746755] kthread+0x107/0x140 [ 6250.746759] ? process_one_work+0x6d0/0x6d0 [ 6250.746763] ? kthread_create_on_node+0x40/0x40 [ 6250.746768] ret_from_fork+0x2e/0x40 [ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]--- v2: - Use the new pci_dev->needs_resume flag, to avoid any overhead during the ->pm_prepare hook. (Rafael) v3: - Update commit message to reference the actual regressing commit. (Lukas) v4: - Rebase on v4 of patch 1/2. Fixes: d14d2a84 ("drm: Remove dev_pm_ops from drm_class") References: https://bugs.freedesktop.org/show_bug.cgi?id=100378 References: https://bugs.freedesktop.org/show_bug.cgi?id=100770 Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Marta Lofstedt <marta.lofstedt@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Tomi Sarvela <tomi.p.sarvela@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Takashi Iwai <tiwai@suse.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: linux-pci@vger.kernel.org Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Reported-and-tested-by:
Marta Lofstedt <marta.lofstedt@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com (cherry picked from commit adfdf85d) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Imre Deak authored
commit 4d071c32 upstream. Some drivers - like i915 - may not support the system suspend direct complete optimization due to differences in their runtime and system suspend sequence. Add a flag that when set resumes the device before calling the driver's system suspend handlers which effectively disables the optimization. Needed by a future patch fixing suspend/resume on i915. Suggested by Rafael. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable@vger.kernel.org (rebased on v4.8, added kernel version to commit message stable tag) Signed-off-by:
-
Chris Wilson authored
This is the minimal backport for stable of the upstream commit: commit dd19674b Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Feb 15 08:43:46 2017 +0000 drm/i915: Remove bitmap tracking for used-ptes Due to a race with the shrinker, when we try to allocate a pagetable, we may end up shrinking it instead. This comes as a nasty surprise as we try to dereference it to fill in the pagetable entries for the object. In linus/master this is fixed by pinning the pagetables prior to allocation, but that backport is roughly drivers/gpu/drm/i915/i915_gem_gtt.c | 10 ---------- 1 file changed, 10 deletions(-) i.e. unsuitable for stable. Instead we neuter the code that tried to free the pagetables. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99295 Fixes: 2ce5179f ("drm/i915/gtt: Free unused lower-level page tables") Signed-off-by:
Maël Lavault <mael.lavault@protonmail.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
-
- 14 Jun, 2017 36 commits
-
-
Greg Kroah-Hartman authored
-
Vegard Nossum authored
commit b0f5a8f3 upstream. This fixes a regression in commit 4d6501dc where I didn't notice that MIPS and OpenRISC were reinitialising p->{set,clear}_child_tid to NULL after our initialisation in copy_process(). We can simply get rid of the arch-specific initialisation here since it is now always done in copy_process() before hitting copy_thread{,_tls}(). Review notes: - As far as I can tell, copy_process() is the only user of copy_thread_tls(), which is the only caller of copy_thread() for architectures that don't implement copy_thread_tls(). - After this patch, there is no arch-specific code touching p->set_child_tid or p->clear_child_tid whatsoever. - It may look like MIPS/OpenRISC wanted to always have these fields be NULL, but that's not true, as copy_process() would unconditionally set them again _after_ calling copy_thread_tls() before commit 4d6501dc. Fixes: 4d6501dc ("kthread: Fix use-after-free if kthread fork fails") Reported-by:
Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> # MIPS only Acked-by:
Stafford Horne <shorne@gmail.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: Jonas Bonn <jonas@southpole.se> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: openrisc@lists.librecores.org Cc: Jamie Iles <jamie.iles@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Pablo Neira Ayuso authored
commit d2df92e9 upstream. The existing code selects no next branch to be inspected when re-inserting an inactive element into the rb-tree, looping endlessly. This patch restricts the check for active elements to the EEXIST case only. Fixes: e701001e ("netfilter: nft_rbtree: allow adjacent intervals with dynamic updates") Reported-by:
Wolfgang Bumiller <w.bumiller@proxmox.com> Tested-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Jani Nikula authored
commit bb1d1329 upstream. The main thing are the DDI ports. If there's a VBT that says there are no outputs, we should trust that, and not have semi-random defaults. Unfortunately, the defaults have resulted in some Chromebooks without VBT to rely on this behaviour, so we split out the defaults for the missing VBT case. Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
commit 66578857 upstream. We don't use the error return for anything other than reporting and logging that there is no VBT. We can pull the logging in the function, and remove the error status return. Moreover, if we needed the information for something later on, we'd probably be better off storing the bit in dev_priv, and using it where it's needed, instead of using the error return. While at it, improve the comments. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Paul Moore authored
commit 48d0e023 upstream. Cong Wang correctly pointed out that the RCU read locking of the auditd_connection struct was wrong, this patch correct this by adopting a more traditional, and correct RCU locking model. This patch is heavily based on an earlier prototype by Cong Wang. Reported-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Thomas Gleixner authored
commit 90b4f30b upstream. The recent conversion to the hotplug state machine missed that the original hotplug notifiers did not execute in the frozen state, which is used on suspend on resume. This does not matter on single socket machines, but on multi socket systems this breaks when the device for a non-boot socket is removed when the last CPU of that socket is brought offline. The device removal locks up the machine hard w/o any debug output. Prevent executing the hotplug callbacks when cpuhp_tasks_frozen is true. Thanks to Tommi for providing debug information patiently while I failed to spot the obvious. Fixes: e00ca5df ("hwmon: (coretemp) Convert to hotplug state machine") Reported-by:
Tommi Rantala <tt.rantala@gmail.com> Tested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Chandan Rajendra authored
commit a008c31c upstream. On a ppc64 machine executing overlayfs/019 with xfs as the lower and upper filesystem causes the following call trace, WARNING: CPU: 2 PID: 8034 at /root/repos/linux/fs/iomap.c:765 .iomap_dio_actor+0xcc/0x420 Modules linked in: CPU: 2 PID: 8034 Comm: fsstress Tainted: G L 4.11.0-rc5-next-20170405 #100 task: c000000631314880 task.stack: c0000003915d4000 NIP: c00000000035a72c LR: c00000000035a6f4 CTR: c00000000035a660 REGS: c0000003915d7570 TRAP: 0700 Tainted: G L (4.11.0-rc5-next-20170405) MSR: 800000000282b032 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI> CR: 24004284 XER: 00000000 CFAR: c0000000006f7190 SOFTE: 1 GPR00: c00000000035a6f4 c0000003915d77f0 c0000000015a3f00 000000007c22f600 GPR04: 000000000022d000 0000000000002600 c0000003b2d56360 c0000003915d7960 GPR08: c0000003915d7cd0 0000000000000002 0000000000002600 c000000000521cc0 GPR12: 0000000024004284 c00000000fd80a00 000000004b04ae64 ffffffffffffffff GPR16: 000000001000ca70 0000000000000000 c0000003b2d56380 c00000000153d2b8 GPR20: 0000000000000010 c0000003bc87bac8 0000000000223000 000000000022f5ff GPR24: c0000003b2d56360 000000000000000c 0000000000002600 000000000022d000 GPR28: 0000000000000000 c0000003915d7960 c0000003b2d56360 00000000000001ff NIP [c00000000035a72c] .iomap_dio_actor+0xcc/0x420 LR [c00000000035a6f4] .iomap_dio_actor+0x94/0x420 Call Trace: [c0000003915d77f0] [c00000000035a6f4] .iomap_dio_actor+0x94/0x420 (unreliable) [c0000003915d78f0] [c00000000035b9f4] .iomap_apply+0xf4/0x1f0 [c0000003915d79d0] [c00000000035c320] .iomap_dio_rw+0x230/0x420 [c0000003915d7ae0] [c000000000512a14] .xfs_file_dio_aio_read+0x84/0x160 [c0000003915d7b80] [c000000000512d24] .xfs_file_read_iter+0x104/0x130 [c0000003915d7c10] [c0000000002d6234] .__vfs_read+0x114/0x1a0 [c0000003915d7cf0] [c0000000002d7a8c] .vfs_read+0xac/0x1a0 [c0000003915d7d90] [c0000000002d96b8] .SyS_read+0x58/0x100 [c0000003915d7e30] [c00000000000b8e0] system_call+0x38/0xfc Instruction dump: 78630020 7f831b78 7ffc07b4 7c7ce039 40820360 a13d0018 2f890003 419e0288 2f890004 419e00a0 2f890001 419e02a8 <0fe00000> 3b80fffb 38210100 7f83e378 The above problem can also be recreated on a regular xfs filesystem using the command, $ fsstress -d /mnt -l 1000 -n 1000 -p 1000 The reason for the call trace is, 1. When 'reserving' blocks for delayed allocation , XFS reserves more blocks (i.e. past file's current EOF) than required. This is done because XFS assumes that userspace might write more data and hence 'reserving' more blocks might lead to the file's new data being stored contiguously on disk. 2. The in-memory 'struct xfs_bmbt_irec' mapping the file's last extent would then cover the prealloc-ed EOF blocks in addition to the regular blocks. 3. When flushing the dirty blocks to disk, we only flush data till the file's EOF. But before writing out the dirty data, we allocate blocks on the disk for holding the file's new data. This allocation includes the blocks that are part of the 'prealloc EOF blocks'. 4. Later, when the last reference to the inode is being closed, XFS frees the unused 'prealloc EOF blocks' in xfs_inactive(). In step 3 above, When allocating space on disk for the delayed allocation range, the space allocator might sometimes allocate less blocks than required. If such an allocation ends right at the current EOF of the file, We will not be able to clear the "delayed allocation" flag for the 'prealloc EOF blocks', since we won't have dirty buffer heads associated with that range of the file. In such a situation if a Direct I/O read operation is performed on file range [X, Y] (where X < EOF and Y > EOF), we flush dirty data in the range [X, Y] and invalidate page cache for that range (Refer to iomap_dio_rw()). Later for performing the Direct I/O read, XFS obtains the extent items (which are still cached in memory) for the file range. When doing so we are not supposed to get an extent item with IOMAP_DELALLOC flag set, since the previous "flush" operation should have converted any delayed allocation data in the range [X, Y]. Hence we end up hitting a WARN_ON_ONCE(1) statement in iomap_dio_actor(). This commit fixes the bug by preventing the read operation from going beyond iomap_dio->i_size. Reported-by:
Santhosh G <santhog4@linux.vnet.ibm.com> Signed-off-by:
Chandan Rajendra <chandan@linux.vnet.ibm.com> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Tejun Heo authored
commit 310b4816 upstream. a590b90d ("cgroup: fix spurious warnings on cgroup_is_dead() from cgroup_sk_alloc()") converted most cgroup_get() usages to cgroup_get_live() leaving cgroup_sk_alloc() the sole user of cgroup_get(). When !CONFIG_SOCK_CGROUP_DATA, this ends up triggering unused warning for cgroup_get(). Silence the warning by adding __maybe_unused to cgroup_get(). Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Link: http://lkml.kernel.org/r/20170501145340.17e8ef86@canb.auug.org.auSigned-off-by:
Tejun Heo <tj@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Wei Yongjun authored
commit a9de080b upstream. Make sure dmi_system_id tables are NULL terminated. Fixes: 70365027 ("pinctrl: cherryview: Add a quirk to make Acer Chromebook keyboard work again") Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Cc: Jean Delvare <jdelvare@suse.de> Signed-off-by:
-
Takatoshi Akiyama authored
commit 3c910176 upstream. This patch fixes an issue that kernel panic happens when DMA is enabled and we press enter key while the kernel booting on the serial console. * An interrupt may occur after sci_request_irq(). * DMA transfer area is initialized by setup_timer() in sci_request_dma() and used in interrupt. If an interrupt occurred between sci_request_irq() and setup_timer() in sci_request_dma(), DMA transfer area has not been initialized yet. So, this patch changes the order of sci_request_irq() and sci_request_dma(). Fixes: 73a19e4c ("serial: sh-sci: Add DMA support.") Signed-off-by:
Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com> [Shimoda changes the commit log] Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Michał Winiarski authored
commit ca7a45ba upstream. Used by production device: Intel(R) Iris(TM) Graphics P555 Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Michał Winiarski <michal.winiarski@intel.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by:
Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
-
Ville Syrjälä authored
commit 668e3b01 upstream. Not calling pm_runtime_enable() means that runtime PM can't be enabled at all via sysfs. So we definitely need to call it from somewhere. Calling it from the driver seems like a bad idea because it would have to be paired with a pm_runtime_disable() at driver unload time, otherwise the core gets upset. Also if there's no LPE audio driver loaded then we couldn't runtime suspend i915 either. So it looks like a better plan is to call it from i915 when we register the platform device. That seems to match how pci generally does things. I cargo culted the pm_runtime_forbid() and pm_runtime_set_active() calls from pci as well. The exposed runtime PM API is massive an thorougly misleading, so I don't actually know if this is how you're supposed to use the API or not. But it seems to work. I can now runtime suspend i915 again with or without the LPE audio driver loaded, and reloading the LPE audio driver also seems to work. Note that powertop won't auto-tune runtime PM for platform devices, which is a little annoying. So I'm not sure that leaving runtime PM in "on" mode by default is the best choice here. But I've left it like that for now at least. Also remove the comment about there not being much benefit from LPE audio runtime PM. Not allowing runtime PM blocks i915 runtime PM, which will also block s0ix, and that could have a measurable impact on power consumption. Cc: Takashi Iwai <tiwai@suse.de> Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Fixes: 0b6b524f ("ALSA: x86: Don't enable runtime PM as default") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-2-ville.syrjala@linux.intel.comReviewed-by:
Takashi Iwai <tiwai@suse.de> (cherry picked from commit 183c0035) Signed-off-by:
-
Julius Werner authored
commit 32829da5 upstream. A recent fix to /dev/mem prevents mappings from wrapping around the end of physical address space. However, the check was written in a way that also prevents a mapping reaching just up to the end of physical address space, which may be a valid use case (especially on 32-bit systems). This patch fixes it by checking the last mapped address (instead of the first address behind that) for overflow. Fixes: b299cde2 ("drivers: char: mem: Check for address space wraparound with mmap()") Reported-by:
Nico Huber <nico.h@gmx.de> Signed-off-by:
Julius Werner <jwerner@chromium.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 40da1b11 upstream. If a custom CPU target is specified and that one is not available _or_ can't be interrupted then the code returns to userland without dropping a lock as notices by lockdep: |echo 133 > /sys/devices/system/cpu/cpu7/hotplug/target | ================================================ | [ BUG: lock held when returning to user space! ] | ------------------------------------------------ | bash/503 is leaving the kernel with locks still held! | 1 lock held by bash/503: | #0: (device_hotplug_lock){+.+...}, at: [<ffffffff815b5650>] lock_device_hotplug_sysfs+0x10/0x40 So release the lock then. Fixes: 757c989b ("cpu/hotplug: Make target state writeable") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Takashi Iwai authored
commit 4efda5f2 upstream. soc_cleanup_card_resources() call snd_card_free() at the last of its procedure. This turned out to lead to a use-after-free. PCM runtimes have been already removed via soc_remove_pcm_runtimes(), while it's dereferenced later in soc_pcm_free() called via snd_card_free(). The fix is simple: just move the snd_card_free() call to the beginning of the whole procedure. This also gives another benefit: it guarantees that all operations have been shut down before actually releasing the resources, which was racy until now. Reported-and-tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit ba3021b2 upstream. snd_timer_user_tselect() reallocates the queue buffer dynamically, but it forgot to reset its indices. Since the read may happen concurrently with ioctl and snd_timer_user_tselect() allocates the buffer via kmalloc(), this may lead to the leak of uninitialized kernel-space data, as spotted via KMSAN: BUG: KMSAN: use of unitialized memory in snd_timer_user_read+0x6c4/0xa10 CPU: 0 PID: 1037 Comm: probe Not tainted 4.11.0-rc5+ #2739 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x143/0x1b0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007 kmsan_check_memory+0xc2/0x140 mm/kmsan/kmsan.c:1086 copy_to_user ./arch/x86/include/asm/uaccess.h:725 snd_timer_user_read+0x6c4/0xa10 sound/core/timer.c:2004 do_loop_readv_writev fs/read_write.c:716 __do_readv_writev+0x94c/0x1380 fs/read_write.c:864 do_readv_writev fs/read_write.c:894 vfs_readv fs/read_write.c:908 do_readv+0x52a/0x5d0 fs/read_write.c:934 SYSC_readv+0xb6/0xd0 fs/read_write.c:1021 SyS_readv+0x87/0xb0 fs/read_write.c:1018 This patch adds the missing reset of queue indices. Together with the previous fix for the ioctl/read race, we cover the whole problem. Reported-by:
Alexander Potapenko <glider@google.com> Tested-by:
-
Takashi Iwai authored
commit d11662f4 upstream. The read from ALSA timer device, the function snd_timer_user_tread(), may access to an uninitialized struct snd_timer_user fields when the read is concurrently performed while the ioctl like snd_timer_user_tselect() is invoked. We have already fixed the races among ioctls via a mutex, but we seem to have forgotten the race between read vs ioctl. This patch simply applies (more exactly extends the already applied range of) tu->ioctl_lock in snd_timer_user_tread() for closing the race window. Reported-by:
-
Ben Skeggs authored
commit b4e382ca upstream. Reusing the list_head for both is a bad idea. Callback execution is done with the lock dropped so that alarms can be rescheduled from the callback, which means that with some unfortunate timing, lists can get corrupted. The execution list should not require its own locking, the single function that uses it can only be called from a single context. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Dominik Brodowski authored
commit 5b0bc9ac upstream. During early boot, load_ucode_intel_ap() uses __load_ucode_intel() to obtain a pointer to the relevant microcode patch (embedded in the initrd), and stores this value in 'intel_ucode_patch' to speed up the microcode patch application for subsequent CPUs. On resuming from suspend-to-RAM, however, load_ucode_ap() calls load_ucode_intel_ap() for each non-boot-CPU. By then the initramfs is long gone so the pointer stored in 'intel_ucode_patch' no longer points to a valid microcode patch. Clear that pointer so that we effectively fall back to the CPU hotplug notifier callbacks to update the microcode. Signed-off-by:
Dominik Brodowski <linux@dominikbrodowski.net> [ Edit and massage commit message. ] Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170607095819.9754-1-bp@alien8.deSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sinclair Yeh authored
commit 07678eca upstream. When vmw_gb_surface_define_ioctl() is called with an existing buffer, we end up returning an uninitialized variable in the backup_handle. The fix is to first initialize backup_handle to 0 just to be sure, and second, when a user-provided buffer is found, we will use the req->buffer_handle as the backup_handle. Reported-by:
Murray McAllister <murray.mcallister@insomniasec.com> Signed-off-by:
Sinclair Yeh <syeh@vmware.com> Reviewed-by:
Deepak Rawat <drawat@vmware.com> Signed-off-by:
-
Vladis Dronov authored
commit ee9c4e68 upstream. The 'req->mip_levels' parameter in vmw_gb_surface_define_ioctl() is a user-controlled 'uint32_t' value which is used as a loop count limit. This can lead to a kernel lockup and DoS. Add check for 'req->mip_levels'. References: https://bugzilla.redhat.com/show_bug.cgi?id=1437431Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Reviewed-by:
-
Dan Carpenter authored
commit f0c62e98 upstream. If vmalloc() fails then we need to a bit of cleanup before returning. Fixes: fb1d9738 ("drm/vmwgfx: Add DRM driver for VMware Virtual GPU") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Timur Tabi authored
commit 24609669 upstream. Use software polling (PHY_POLL) to check for link state changes instead of relying on the EMAC's hardware polling feature. Some PHY drivers are unable to get a functioning link because the HW polling is not robust enough. The EMAC is able to poll the PHY on the MDIO bus looking for link state changes (via the Link Status bit in the Status Register at address 0x1). When the link state changes, the EMAC triggers an interrupt and tells the driver what the new state is. The feature eliminates the need for software to poll the MDIO bus. Unfortunately, this feature is incompatible with phylib, because it ignores everything that the PHY core and PHY drivers are trying to do. In particular: 1. It assumes a compatible register set, so PHYs with different registers may not work. 2. It doesn't allow for hardware errata that have work-arounds implemented in the PHY driver. 3. It doesn't support multiple register pages. If the PHY core switches the register set to another page, the EMAC won't know the page has changed and will still attempt to read the same PHY register. 4. It only checks the copper side of the link, not the SGMII side. Some PHY drivers (e.g. at803x) may also check the SGMII side, and report the link as not ready during autonegotiation if the SGMII link is still down. Phylib then waits for another interrupt to query the PHY again, but the EMAC won't send another interrupt because it thinks the link is up. Tested-by:
Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by:
Timur Tabi <timur@codeaurora.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Paolo Bonzini authored
commit 1123a604 upstream. Linu Cherian reported a WARN in cleanup_srcu_struct() when shutting down a guest running iperf on a VFIO assigned device. This happens because irqfd_wakeup() calls srcu_read_lock(&kvm->irq_srcu) in interrupt context, while a worker thread does the same inside kvm_set_irq(). If the interrupt happens while the worker thread is executing __srcu_read_lock(), updates to the Classic SRCU ->lock_count[] field or the Tree SRCU ->srcu_lock_count[] field can be lost. The docs say you are not supposed to call srcu_read_lock() and srcu_read_unlock() from irq context, but KVM interrupt injection happens from (host) interrupt context and it would be nice if SRCU supported the use case. KVM is using SRCU here not really for the "sleepable" part, but rather due to its IPI-free fast detection of grace periods. It is therefore not desirable to switch back to RCU, which would effectively revert commit 719d93cd ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING", 2014-01-16). However, the docs are overly conservative. You can have an SRCU instance only has users in irq context, and you can mix process and irq context as long as process context users disable interrupts. In addition, __srcu_read_unlock() actually uses this_cpu_dec() on both Tree SRCU and Classic SRCU. For those two implementations, only srcu_read_lock() is unsafe. When Classic SRCU's __srcu_read_unlock() was changed to use this_cpu_dec(), in commit 5a41344a ("srcu: Simplify __srcu_read_unlock() via this_cpu_dec()", 2012-11-29), __srcu_read_lock() did two increments. Therefore it kept __this_cpu_inc(), with preempt_disable/enable in the caller. Tree SRCU however only does one increment, so on most architectures it is more efficient for __srcu_read_lock() to use this_cpu_inc(), and any performance differences appear to be down in the noise. Fixes: 719d93cd ("kvm/irqchip: Speed up KVM_SET_GSI_ROUTING") Reported-by:
Linu Cherian <linuc.decode@gmail.com> Suggested-by:
Paolo Bonzini <pbonzini@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
Jin Yao authored
commit cc1582c2 upstream. When doing sampling, for example: perf record -e cycles:u ... On workloads that do a lot of kernel entry/exits we see kernel samples, even though :u is specified. This is due to skid existing. This might be a security issue because it can leak kernel addresses even though kernel sampling support is disabled. The patch drops the kernel samples if exclude_kernel is specified. For example, test on Haswell desktop: perf record -e cycles:u <mgen> perf report --stdio Before patch applied: 99.77% mgen mgen [.] buf_read 0.20% mgen mgen [.] rand_buf_init 0.01% mgen [kernel.vmlinux] [k] apic_timer_interrupt 0.00% mgen mgen [.] last_free_elem 0.00% mgen libc-2.23.so [.] __random_r 0.00% mgen libc-2.23.so [.] _int_malloc 0.00% mgen mgen [.] rand_array_init 0.00% mgen [kernel.vmlinux] [k] page_fault 0.00% mgen libc-2.23.so [.] __random 0.00% mgen libc-2.23.so [.] __strcasestr 0.00% mgen ld-2.23.so [.] strcmp 0.00% mgen ld-2.23.so [.] _dl_start 0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4 0.00% mgen ld-2.23.so [.] _start We can see kernel symbols apic_timer_interrupt and page_fault. After patch applied: 99.79% mgen mgen [.] buf_read 0.19% mgen mgen [.] rand_buf_init 0.00% mgen libc-2.23.so [.] __random_r 0.00% mgen mgen [.] rand_array_init 0.00% mgen mgen [.] last_free_elem 0.00% mgen libc-2.23.so [.] vfprintf 0.00% mgen libc-2.23.so [.] rand 0.00% mgen libc-2.23.so [.] __random 0.00% mgen libc-2.23.so [.] _int_malloc 0.00% mgen libc-2.23.so [.] _IO_doallocbuf 0.00% mgen ld-2.23.so [.] do_lookup_x 0.00% mgen ld-2.23.so [.] open_verify.constprop.7 0.00% mgen ld-2.23.so [.] _dl_important_hwcaps 0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4 0.00% mgen ld-2.23.so [.] _start There are only userspace symbols. Signed-off-by:
Jin Yao <yao.jin@linux.intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: acme@kernel.org Cc: jolsa@kernel.org Cc: kan.liang@intel.com Cc: mark.rutland@arm.com Cc: will.deacon@arm.com Cc: yao.jin@intel.com Link: http://lkml.kernel.org/r/1495706947-3744-1-git-send-email-yao.jin@linux.intel.comSigned-off-by:
-
Andrew Lunn authored
commit 3e4240da upstream. This reverts commit 368e5fbd. devm_ioremap_resource() enforces that there are no overlapping resources, where as devm_ioremap() does not. The sata phy driver needs a subset of the sata IO address space, so maps some of the sata address space. As a result, sata_mv now fails to probe, reporting it cannot get its resources, and so we don't have any SATA disks. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Breno Leitao authored
commit 7f22ced4 upstream. Currently tsk->thread.load_tm is not initialized in the task creation and can contain garbage on a new task. This is an undesired behaviour, since it affects the timing to enable and disable the transactional memory laziness (disabling and enabling the MSR TM bit, which affects TM reclaim and recheckpoint in the scheduling process). Fixes: 5d176f75 ("powerpc: tm: Enable transactional memory (TM) lazily for userspace") Signed-off-by:
Breno Leitao <leitao@debian.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Breno Leitao authored
commit 1195892c upstream. Currently tsk->thread->load_vec and load_fp are not initialized during task creation, which can lead to garbage values in these variables (non-zero values). These variables will be checked later in restore_math() to validate if the FP and vector registers are being utilized. Since these values might be non-zero, the restore_math() will continue to save the FP and vectors even if they were never utilized by the userspace application. load_fp and load_vec counters will then overflow (they wrap at 255) and the FP and Altivec will be finally disabled, but before that condition is reached (counter overflow) several context switches will have restored FP and vector registers without need, causing a performance degradation. Fixes: 70fe3d98 ("powerpc: Restore FPU/VEC/VSX if previously used") Signed-off-by:
Gustavo Romero <gusbromero@gmail.com> Acked-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Michael Bringmann authored
commit dc421b20 upstream. When adding or removing memory, the aa_index (affinity value) for the memblock must also be converted to match the endianness of the rest of the 'ibm,dynamic-memory' property. Otherwise, subsequent retrieval of the attribute will likely lead to non-existent nodes, followed by using the default node in the code inappropriately. Fixes: 5f97b2a0 ("powerpc/pseries: Implement memory hotplug add in the kernel") Signed-off-by:
Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by:
-
Michael Ellerman authored
commit ba4a648f upstream. In commit 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we switched to the generic implementation of cpu_to_node(), which uses a percpu variable to hold the NUMA node for each CPU. Unfortunately we neglected to notice that we use cpu_to_node() in the allocation of our percpu areas, leading to a chicken and egg problem. In practice what happens is when we are setting up the percpu areas, cpu_to_node() reports that all CPUs are on node 0, so we allocate all percpu areas on node 0. This is visible in the dmesg output, as all pcpu allocs being in group 0: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31 pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39 pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47 To fix it we need an early_cpu_to_node() which can run prior to percpu being setup. We already have the numa_cpu_lookup_table we can use, so just plumb it in. With the patch dmesg output shows two groups, 0 and 1: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31 pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39 pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47 We can also check the data_offset in the paca of various CPUs, with the fix we see: CPU 0: data_offset = 0x0ffe8b0000 CPU 24: data_offset = 0x1ffe5b0000 And we can see from dmesg that CPU 24 has an allocation on node 1: node 0: [mem 0x0000000000000000-0x0000000fffffffff] node 1: [mem 0x0000001000000000-0x0000001fffffffff] Fixes: 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID") Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Christophe Leroy authored
commit 6f553912 upstream. of_mm_gpiochip_add_data() generates an oops for NULL pointer dereference. of_mm_gpiochip_add_data() calls mm_gc->save_regs() before setting the data, therefore ->save_regs() cannot use gpiochip_get_data() Fixes: 937daafc ("powerpc: simple-gpio: use gpiochip data pointer") Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by:
-
Joe Carnuccio authored
commit 74939a0b upstream. Signed-off-by:
Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Joe Carnuccio authored
commit 1d634965 upstream. Set bit (BIT_15) to send right ECHO payload information for Diagnostic Echo Test command. Signed-off-by:
-
Joe Carnuccio authored
commit ce6c668b upstream. Firmware dump allows for debugging customer issues. This patch fixes start/end pointer calculation to capture T262 template entry for dump tool. Signed-off-by:
-
Quinn Tran authored
commit 0ea88662 upstream. Remove redundant fc_host_port_name calls to prevent early access of scsi_host->shost_data buffer. This prevent null pointer access. Following stack trace is seen: BUG: unable to handle kernel NULL pointer dereference at 00000000000008 IP: qla24xx_report_id_acquisition+0x22d/0x3a0 [qla2xxx] Signed-off-by:
Quinn Tran <quinn.tran@cavium.com> Signed-off-by:
-
