SDHCI_CTRL_HS_SDR200 is unused.  Remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

AMD SD controller supports the SDR104 mode, but caps2 can not
be promoted to support hs200 for eMMC.
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch is to enable the quirk for AMD sdhci requiring transfer
mode register need to be cleared for commands without data
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Vikram B <vikram.b@amd.com>
Tested-by: Raghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It is possible that we may fail to set the clock rate, if we do so then
log the failure and don't bother reprogramming the IP.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add runtime pm support to atmel mci controller.
Use runtime pm APIs to enable/disable atmel mci's clock.
Use runtime autosuspend APIs to enable auto suspend delay.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Fixed compile error]

The "Badly aligned" tests, test reading/writing with alignments
of 1,2 and 3.  SDHCI now has 64-bit ADMA which has 8-byte
alignment, so extend the tests to test up to 7.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set a 64-bit DMA mask when using 64-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set the DMA mask during the first call to ->enable_dma() to
make use of the SDHCI_USE_64_BIT_DMA flag.

This patch is dependent on
commit 8a2f38dd ("ACPI / platform: provide default DMA mask")
which provides the dev->dma_mask pointer without
which dma_set_mask_and_coherent() will always fail.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add 64-bit ADMA support including:
	- add 64-bit ADMA descriptor
	- add SDHCI_USE_64_BIT_DMA flag
	- set upper 32-bits of DMA addresses
	- ability to select 64-bit ADMA
	- ability to use 64-bit ADMA sizes and alignment
	- display "ADMA 64-bit" when host is added

It is assumed that a 64-bit capable device has set a 64-bit DMA mask
and *must* do 64-bit DMA.  A driver has the opportunity to change
that during the first call to ->enable_dma().  Similarly
SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
implement.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define the ADMA descriptor structure instead of
using manual offsets and casts.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define all the ADMA constants instead of having numbers
scattered throughout the code.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define the maximum number of segments instead of
having the constant 128 appearing in the code in
various places.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for 64-bit ADMA, parameterize ADMA sizes
and alignment.  64-bit ADMA has a larger descriptor
because it contains a 64-bit address instead of a 32-bit
address.  Also data must be 8-byte aligned instead
of 4-byte aligned.  Consequently, sdhci_host members
are added for descriptor, table, and buffer sizes
and alignment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It is kernel-style to use 'void *' for anonymous data.
This is being applied to the ADMA bounce buffer which
contains unaligned bytes, and to the ADMA descriptor
table which will contain 32-bit ADMA descriptors
or 64-bit ADMA descriptors when support is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for 64-bit ADMA, separate out code
that touches the ADMA descriptor by adding
sdhci_adma_mark_end().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for 64-bit ADMA, rename adma_desc to
adma_table.  That is because members will be added
for descriptor size and table size, so using adma_desc
(which is the table) is confusing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Rename sdhci_set_adma_desc to sdhci_adma_write_desc and
sdhci_show_adma_error to sdhci_adma_show_error so that
all ADMA functions start with sdhci_adma_.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The intent of the warning is to warn if the ADMA table
overflows.  However there can be one more 'end' entry
so the condition should be adjusted accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Bytes are being copied from/to a single page.  The intent
of the warning is to warn if the page boundary is crossed.
There are two problems.  First, PAGE_MASK is mistaken for
(PAGE_SIZE - 1).  Secondly, instead of using the number
of bytes to copy, the warning is using the maximum that
that value could be.  Fix both.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The ADMA2 descriptor table size was being calculated incorrectly
Fix it.

Note that it has been wrong for a long time and likely has not
caused any problems because of a combination of 1) not needing
alignment descriptors for block operations 2) more memory being
allocated than was requested 3) the use of
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC which does not use an extra
descriptor for the end marker.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for non-removable slots which have no card detection GPIO
and which should not be polled for a card change.
Signed-off-by: Timo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now that sdhci-pxav3 driver allows to have more than one IP clock defined,
document both clocks and clock-names properties.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Besides the I/O clock, some PXAv3 SDHCI IP also requires a core clock to
be enabled. Add an optional core clock to the corresponding driver.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

With support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "io" clock
before falling back to unnamed clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As we are using references to the I/O clock throughout the driver,
move it to the private data. Also, in preparation for core clock,
rename it to clk_io.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_add_host and sdhci_platfm_init already report failure,
so don't emit error messages when a failure occurs. This prevents
occurences of "deferred" messages when required power supplies
are not ready for operation yet.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

While allocating buffers for CXD data, let's use kzalloc() to make sure
those are zeroed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Due to previous patches, all callers of mmc_send_cxd_data() now
allocates their buffers from the heap. This enables us to simplify
mmc_send_cxd_data() by removing the support of handling buffers, which
are allocated from the stack.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Previous patches has replaced the calls to mmc_send_ext_csd() into
mmc_get_ext_csd(), thus mmc_send_ext_csd() has become redundant. Let's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

By using mmc_get_ext_csd() in favor of mmc_send_ext_csd, we decrease
code duplication.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

By using mmc_get_ext_csd() in favor of mmc_send_ext_csd, we decrease
code duplication.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Callers of mmc_send_ext_csd() will be able to decrease code duplication
by using mmc_get_ext_csd() instead. Let's make it available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Instead of doing BUG_ON(), return an error code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The callers of mmc_get_ext_csd() need the flexibility to handle errors
themselves, because they behave differently.

Let's clean up mmc_get_ext_csd() with its friends and adopt the error
handling as stated above.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As a step in cleaning up code around reading/decoding EXT_CSD, convert
the current mmc_read_ext_csd(), to handle both fetching the EXT_CSD
and decoding its data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The helper function mmc_can_ext_csd() will return a positive value if
the card supports the EXT_CSD register. Start using it at relavant
places in the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Rely on the prints handled internally by kmalloc().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>