This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always across the whole page (up to 2k pages).

Limitations:
- HW ECC: Only 2K page with 64+ OOB.
- HW ECC: Only 24 and 32-bit error correction implemented.

Raw writes have been tested using the generic nand_write_page_raw
implementation. However, raw reads are currently not possible
because the controller need to know whether we are going to use
the ECC mode already at NAND_CMD_READ0 command time. At this point
we do not have the information whether it is a raw read or a
regular read at driver level...
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This driver supports Freescale NFC (NAND flash controller) found on
Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has
been tested using 8-bit and 16-bit NAND interface on the ARM based
Vybrid SoC VF500 and VF610 platform.
parameter page reading.

Limitations:
- Untested on MPC5125 and M54418.
- DMA and pipelining not used.
- 2K pages or less.
- No chip select, one NAND chip per controller.
- No hardware ECC.

Some paths have been hand-optimized and evaluated by measurements
made using mtd_speedtest.ko on a 100MB MTD partition.

Colibri VF50
        eb write     %   eb read     %   page write      %   page read     %
rel/opt     5175           11537                4560             11039
opt         5164 -0.21     11420 -1.01          4737 +3.88       10918 -1.10
none        5113 -1.20     11352 -1.60          4490 -1.54       10865 -1.58

Colibri VF61
        eb write     %   eb read     %   page write      %   page read     %
rel/opt     5766           13096                5459             12846
opt         5883 +2.03     13064 -0.24          5561 +1.87       12802 -0.34
none        5701 -1.13     12980 -0.89          5488 +0.53       12735 -0.86

rel = using readl_relaxed/writel_relaxed in optimized paths
opt = hand-optimized by combining multiple accesses into one read/write

The measurements have not been statistically verfied, hence use them
with care. The author came to the conclusion that using the relaxed
variants of readl/writel are not worth the additional code.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

After a bit of poking around wondering why my 32-bit user-space can't
seem to send a proper ioctl(BLKPG) to an MTD on my 64-bit kernel
(ARM64), I noticed that struct blkpg_ioctl_arg is actually pretty
unsuitable for use in the ioctl() ABI, due to its use of raw pointers,
and its lack of alignment/packing restrictions (32-bit arch'es tend to
pack the 4 fields into 4 32-bit words, whereas 64-bit arch'es would add
padding after the third int, and make this 6 32-bit words).

Anyway, this means BLKPG deserves some special compat_ioctl handling. Do
the conversion in a small shim for MTD.

block/compat_ioctl.c already has compat support for the block subsystem,
but it does so by a re-marshalling data to/from user-space (see
compat_blkpg_ioctl()). Personally, I think this approach is cleaner.

Tested only on MTD, with an ARM32 user space on an ARM64 kernel.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Tested only with single I/O, but the datasheet says it supports dual and
quad.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch fixes timeout issues seen on large NOR flash (e.g., 16MB
w25q128fw) when using ioctl(MEMERASE) with offset=0 and length=16M. The
input parameters matter because spi_nor_erase() uses a different code
path for full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode.

Fix: use a different timeout for full-chip erase than for other
commands.

While most operations can be expected to perform relatively similarly
across a variety of NOR flash types and sizes (and therefore might as
well use a similar timeout to keep things simple), full-chip erase is
unique, because the time it typically takes to complete:
(1) is much larger than most operations and
(2) scales with the size of the flash.

Let's base our timeout on the original comments stuck here -- that a 2MB
flash requires max 40s to erase.

Small survey of a few flash datasheets I have lying around:

  Chip         Size (MB)   Max chip erase (seconds)
  ----         --------    ------------------------
  w25q32fw     4           50
  w25q64cv     8           30
  w25q64fw     8           100
  w25q128fw    16          200
  s25fl128s    16          ~256
  s25fl256s    32          ~512

From this data, it seems plenty sufficient to say we need to wait for
40 seconds for each 2MB of flash.

After this change, it might make some sense to decrease the timeout for
everything else, as even the most extreme operations (single block
erase?) shouldn't take more than a handful of seconds. But for safety,
let's leave it as-is. It's only an error case, after all, so we don't
exactly need to optimize it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

It is a 512KiB flash with 4 KiB erase sectors.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The module pcmciamtd doesn't generate a mtd node for PRETEC 4MB SRAM
cards without the id and hash added to pcmciamtd.c

Tested on 3 different 4MB pretec sram cards.
Signed-off-by: Tom Englund <tomenglund26@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Read Denali hardware revision number and use it to
calculate max_banks,  The encoding of max_banks changed
in Denali revision 5.1.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

A read id operation followed by 0x00 reads the device ID while
a read id operation followed by 0x20 reads the possible ONFI identifier.

As the READID function did not propagate the second id parameter but had
a hard-coded call for 0x90 0x00, reading the ONFI identifier was not
possible and thus chips werde not detected (tested with
MT29F8G08ABABAWP)
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

c->oobbuf hasn't been kmalloced in jffs2_dataflash_setup, so
there is no need to free it.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This driver uses some custom macros for printing. Let's use the standard
pr_fmt()/pr_{err,warn}().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

I'm not sure why we have a PAGE_SIZE restriction on this partition
parser.

If we really wanted the restriction, I would expect it to be a
restriction for *all* parsers, so we'd move it to the MTD core

At any rate, while small partitions may not be useful (they'll often be
smaller than the eraseblock size and therefore can only be used
read-only), they still have use as a read-only partition.

This restriction is especially annoying because it aborts the entire
MTD's cmdline parsing, leaving it unpartitioned.

So, let's kill the restriction and only check for zero-sized partitions,
which I expect we don't want to allow.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

s25fl016k can be found on Embedded Artists' LPC4357 Developer's Kit
where is used in quad mode by the LPC4357 SPIFI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Destroy mtd_idr on module_exit, reclaiming the allocated memory.

This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@

module_init(init);

@ defines_module_exit @
identifier exit;
@@

module_exit(exit);

@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@

DEFINE_IDR(idr);

@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
  idr_destroy(&idr);
  ...
}

@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 +idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

After the conversion of pxa architecture to common clock framework, the
NAND clock can be disabled on driver exit.

In this case, it happens that if the driver used the NAND and set the
DFI arbitration bit, the next access to a static memory controller area,
such as an ethernet card, will stall the system bus, and the core will
be stalled forever.

This is especially true on pxa31x SoCs, where the NDCR was augmented
with a new bit to prevent this lockups by giving full ownership of the
DFI arbiter to the SMC, in change SCr#6.

Fix this by clearing the DFI arbritration bit in driver exit. This
effectively prevents a lockup on zylonite when removing pxa3xx-nand
module, and using ethernet afterwards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In drivers/mtd/mtd_blkdevs.c:
406	set_capacity(gd, (new->size * tr->blksize) >> 9);
The type of new->size is unsigned long and the type of tr->blksize is int,
the result of 'new->size * tr->blksize' may exceed ULONG_MAX on 32bit
machines.

I use nand chip MT29F32G08CBADBWP which is 4GB and the parameters passed
to kernel is 'mtdparts=gpmi-nand:-(user)', the whole nand chip will be
treated as a 4GB mtd partition. new->size is 0x800000 and tr->blksize is
0x200, 'new->size * tr->blksize' however is 0. This is what we do not want
to see.

Using type cast u64 to fix the multiplication overflow issue.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

As new_valid_dev always returns 1, so !new_valid_dev check is not
needed, remove it.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Now pxa architecture has a dmaengine driver, remove the access to direct
dma registers in favor of the more generic dmaengine code.

This should be also applicable for mmp and orion, provided they work in
device-tree environment.

This patch also removes the previous hack which was necessary to make
the driver work in a devicetree environment.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
[Brian: fixup use of 'enum dma_transfer_direction']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Remove unneeded NULL test.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ expression x; @@
-if (x != NULL)
  \(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Remove unneeded NULL test.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ expression x; @@
-if (x != NULL)
  \(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

struct spi_nor_xfer_cfg and read_xfer/write_xfer hooks were never used by
any driver. Do some cleanup by removing them.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add two helper functions to help NAND controller drivers test whether a
specific NAND region is erased or not.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Pull CRIS updates from Jesper Nilsson:
 "Mostly removal of old cruft of which we can use a generic version, or
  fixes for code not commonly run in the cris port, but also additions
  to enable some good debug"

* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
  CRISv10: delete unused lib/dmacopy.c
  CRISv10: delete unused lib/old_checksum.c
  CRIS: fix switch_mm() lockdep splat
  CRISv32: enable LOCKDEP_SUPPORT
  CRIS: add STACKTRACE_SUPPORT
  CRISv32: annotate irq enable in idle loop
  CRISv32: add support for irqflags tracing
  CRIS: UAPI: use generic types.h
  CRIS: UAPI: use generic shmbuf.h
  CRIS: UAPI: use generic msgbuf.h
  CRIS: UAPI: use generic socket.h
  CRIS: UAPI: use generic sembuf.h
  CRIS: UAPI: use generic sockios.h
  CRIS: UAPI: use generic auxvec.h
  CRIS: UAPI: use generic headers via Kbuild
  CRIS: UAPI: fix elf.h export
  CRIS: don't make asm/elf.h depend on asm/user.h
  CRIS: UAPI: fix ptrace.h
  CRISv32: Squash compile warnings for axisflashmap
  CRISv32: Add GPIO driver to the default configs
  ...

rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.

Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct

    switch (rq_data_dir(req)) {
        case READ:
            ...
        case WRITE:
            ...

that we have in a few drivers.

Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:

  drivers/block/hd.c: In function ‘hd_request’:
  drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
     switch (rq_data_dir(req)) {

The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit 5953316d ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.

But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix up the writeback plugging introduced in commit d353d758
("writeback: plug writeback at a high level") that then caused problems
due to the unplug happening with a spinlock held.

* writeback-plugging:
  writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
  Revert "writeback: plug writeback at a high level"

We had to revert the pluggin in writeback_sb_inodes() because the
wb->list_lock is held, but we could easily plug at a higher level before
taking that lock, and unplug after releasing it.  This does that.

Chris will run performance numbers, just to verify that this approach is
comparable to the alternative (we could just drop and re-take the lock
around the blk_finish_plug() rather than these two commits.

I'd have preferred waiting for actual performance numbers before picking
one approach over the other, but I don't want to release rc1 with the
known "sleeping function called from invalid context" issue, so I'll
pick this cleanup version for now.  But if the numbers show that we
really want to plug just at the writeback_sb_inodes() level, and we
should just play ugly games with the spinlock, we'll switch to that.

Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.

In thermal-core, commit 17e8351a ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.

But in parallel, in the thermal-intel branch commit d0a12625
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.

This resulted in warnings like this:

  drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
    .get_temp = pch_thermal_get_temp,
                ^
  drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
  drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
    .get_trip_temp = pch_get_trip_temp,
                     ^
  drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)

This fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge fourth patch-bomb from Andrew Morton:

 - sys_membarier syscall

 - seq_file interface changes

 - a few misc fixups

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
  mm/early_ioremap: add explicit #include of asm/early_ioremap.h
  fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
  selftests: enhance membarrier syscall test
  selftests: add membarrier syscall test
  sys_membarrier(): system-wide memory barrier (generic, x86)
  MODSIGN: fix a compilation warning in extract-cert

Newer bitfiles needs the reduced clk even for SMP builds

Cc: <stable@vger.kernel.org>  #4.2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB fixes from Jon Mason:
 "NTB bug and documentation fixes, new device IDs, performance
  improvements, and adding a mailing list to MAINTAINERS for NTB"

* tag 'ntb-4.3' of git://github.com/jonmason/ntb:
  NTB: Fix range check on memory window index
  NTB: Improve index handling in B2B MW workaround
  NTB: Fix documentation for ntb_peer_db_clear.
  NTB: Fix documentation for ntb_link_is_up
  NTB: Use unique DMA channels for TX and RX
  NTB: Remove dma_sync_wait from ntb_async_rx
  NTB: Clean up QP stats info
  NTB: Make the transport list in order of discovery
  NTB: Add PCI Device IDs for Broadwell Xeon
  NTB: Add flow control to the ntb_netdev
  NTB: Add list to MAINTAINERS

Pull more input updates from Dmitry Torokhov:
 "Second round of updates for the input subsystem.

  This introduces two brand new touchscreen drivers (Colibri and
  imx6ul_tsc), some small driver fixes, and we are no longer report
  errors from evdev_flush() as users do not really have a way of
  handling errors, error codes that we were returning were not on the
  list of errors supposed to be returned by close(), and errors were
  causing issues with one of older versions of systemd"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: imx_keypad - remove obsolete comment
  Input: touchscreen - add imx6ul_tsc driver support
  Input: Add touchscreen support for Colibri VF50
  Input: i8042 - lower log level for "no controller" message
  Input: evdev - do not report errors form flush()
  Input: elants_i2c - extend the calibration timeout to 12 seconds
  Input: sparcspkr - fix module autoload for OF platform drivers
  Input: regulator-haptic - fix module autoload for OF platform driver
  Input: pwm-beeper - fix module autoload for OF platform driver
  Input: ab8500-ponkey - Fix module autoload for OF platform driver
  Input: cyttsp - remove unnecessary MODULE_ALIAS()
  Input: elan_i2c - add ACPI ID "ELAN1000"

Pull more power management and ACPI updates from Rafael Wysocki:
 "These are mostly fixes and cleanups on top of the previous PM+ACPI
  pull request (cpufreq core and drivers, cpuidle, generic power domains
  framework).  Some of them didn't make to that pull request and some
  fix issues introduced by it.

  The only really new thing is the support for suspend frequency in the
  cpufreq-dt driver, but it is needed to fix an issue with Exynos
  platforms.

  Specifics:

   - build fix for the new Mediatek MT8173 cpufreq driver (Guenter
     Roeck).

   - generic power domains framework fixes (power on error code path,
     subdomain removal) and cleanup of a deprecated API user (Geert
     Uytterhoeven, Jon Hunter, Ulf Hansson).

   - cpufreq-dt driver fixes including two fixes for bugs related to the
     new Operating Performance Points Device Tree bindings introduced
     recently (Viresh Kumar).

   - suspend frequency support for the cpufreq-dt driver (Bartlomiej
     Zolnierkiewicz, Viresh Kumar).

   - cpufreq core cleanups (Viresh Kumar).

   - intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi).

   - additional sanity check in the cpuidle core (Xunlei Pang).

   - fix for a comment related to CPU power management (Lina Iyer)"

* tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_pstate: fix PCT_TO_HWP macro
  intel_pstate: Fix user input of min/max to legal policy region
  PM / OPP: Return suspend_opp only if it is enabled
  cpufreq-dt: add suspend frequency support
  cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
  PM / OPP: add dev_pm_opp_get_suspend_opp() helper
  staging: board: Migrate away from __pm_genpd_name_add_device()
  cpufreq: Use __func__ to print function's name
  cpufreq: staticize cpufreq_cpu_get_raw()
  PM / Domains: Ensure subdomain is not in use before removing
  cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
  cpuidle/coupled: Add sanity check for safe_state_index
  PM / Domains: Try power off masters in error path of __pm_genpd_poweron()
  cpufreq: dt: Tolerance applies on both sides of target voltage
  cpufreq: dt: Print error on failing to mark OPPs as shared
  cpufreq: dt: Check OPP count before marking them shared
  kernel/cpu_pm: fix cpu_cluster_pm_exit comment

Pull SCSI target updates from Nicholas Bellinger:
 "Here are the outstanding target-pending updates for v4.3-rc1.

  Mostly bug-fixes and minor changes this round.  The fallout from the
  big v4.2-rc1 RCU conversion have (thus far) been minimal.

  The highlights this round include:

   - Move sense handling routines into scsi_common code (Sagi)

   - Return ABORTED_COMMAND sense key for PI errors (Sagi)

   - Add tpg_enabled_sendtargets attribute for disabled iscsi-target
     discovery (David)

   - Shrink target struct se_cmd by rearranging fields (Roland)

   - Drop iSCSI use of mutex around max_cmd_sn increment (Roland)

   - Replace iSCSI __kernel_sockaddr_storage with sockaddr_storage (Andy +
     Chris)

   - Honor fabric max_data_sg_nents I/O transfer limit (Arun + Himanshu +
     nab)

   - Fix EXTENDED_COPY >= v4.1 regression OOPsen (Alex + nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (37 commits)
  target: use stringify.h instead of own definition
  target/user: Fix UFLAG_UNKNOWN_OP handling
  target: Remove no-op conditional
  target/user: Remove unused variable
  target: Fix max_cmd_sn increment w/o cmdsn mutex regressions
  target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess
  target/qla2xxx: Honor max_data_sg_nents I/O transfer limit
  target/iscsi: Replace __kernel_sockaddr_storage with sockaddr_storage
  target/iscsi: Replace conn->login_ip with login_sockaddr
  target/iscsi: Keep local_ip as the actual sockaddr
  target/iscsi: Fix np_ip bracket issue by removing np_ip
  target: Drop iSCSI use of mutex around max_cmd_sn increment
  qla2xxx: Update tcm_qla2xxx module description to 24xx+
  iscsi-target: Add tpg_enabled_sendtargets for disabled discovery
  drivers: target: Drop unlikely before IS_ERR(_OR_NULL)
  target: check DPO/FUA usage for COMPARE AND WRITE
  target: Shrink struct se_cmd by rearranging fields
  target: Remove cmd->se_ordered_id (unused except debug log lines)
  target: add support for START_STOP_UNIT SCSI opcode
  target: improve unsupported opcode message
  ...