- 30 Jul, 2020 6 commits
-
-
Felix Fietkau authored
This warning can trigger if there is a mismatch between frames that were sent with the sta pointer set vs tx status frames reported for the sta address. This can happen due to race conditions on re-creating stations, or even in the case of .sta_add/remove being used instead of .sta_state, which can cause frames to be sent to a station that has not been uploaded yet. If there is an actual underflow issue, it should show up in the device airtime warning below, so it is better to remove this one. Signed-off-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20200725084533.13829-1-nbd@nbd.nameSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Vasanthakumar Thiagarajan authored
Allocated ack_frame id from local->ack_status_frames is not really stored in the tx_info for 802.3 Tx path. Due to this, tx ack status is not reported and ack_frame id is not freed for the buffers requiring tx ack status. Also move the memset to 0 of tx_info before IEEE80211_TX_CTL_REQ_TX_STATUS flag assignment. Fixes: 50ff477a ("mac80211: add 802.11 encapsulation offloading support") Signed-off-by:
Vasanthakumar Thiagarajan <vthiagar@codeaurora.org> Link: https://lore.kernel.org/r/1595427617-1713-1-git-send-email-vthiagar@codeaurora.orgSigned-off-by:
-
Julian Squires authored
In the case where a vendor command does not implement doit, and has no flags set, doit would not be validated and a NULL pointer dereference would occur, for example when invoking the vendor command via iw. I encountered this while developing new vendor commands. Perhaps in practice it is advisable to always implement doit along with dumpit, but it seems reasonable to me to always check doit anyway, not just when NEED_WDEV. Signed-off-by:
Julian Squires <julian@cipht.net> Link: https://lore.kernel.org/r/20200706211353.2366470-1-julian@cipht.netSigned-off-by:
-
Remi Pommarel authored
A mpath object can hold reference on a list of skb that are waiting for mpath resolution to be sent. When destroying a mpath this skb list should be cleaned up in order to not leak memory. Fixing that kind of leak: unreferenced object 0xffff0000181c9300 (size 1088): comm "openvpn", pid 1782, jiffies 4295071698 (age 80.416s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 f9 80 36 00 00 00 00 00 ..........6..... 02 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............ backtrace: [<000000004bc6a443>] kmem_cache_alloc+0x1a4/0x2f0 [<000000002caaef13>] sk_prot_alloc.isra.39+0x34/0x178 [<00000000ceeaa916>] sk_alloc+0x34/0x228 [<00000000ca1f1d04>] inet_create+0x198/0x518 [<0000000035626b1c>] __sock_create+0x134/0x328 [<00000000a12b3a87>] __sys_socket+0xb0/0x158 [<00000000ff859f23>] __arm64_sys_socket+0x40/0x58 [<00000000263486ec>] el0_svc_handler+0xd0/0x1a0 [<0000000005b5157d>] el0_svc+0x8/0xc unreferenced object 0xffff000012973a40 (size 216): comm "openvpn", pid 1782, jiffies 4295082137 (age 38.660s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 c0 06 16 00 00 ff ff 00 93 1c 18 00 00 ff ff ................ backtrace: [<000000004bc6a443>] kmem_cache_alloc+0x1a4/0x2f0 [<0000000023c8c8f9>] __alloc_skb+0xc0/0x2b8 [<000000007ad950bb>] alloc_skb_with_frags+0x60/0x320 [<00000000ef90023a>] sock_alloc_send_pskb+0x388/0x3c0 [<00000000104fb1a3>] sock_alloc_send_skb+0x1c/0x28 [<000000006919d2dd>] __ip_append_data+0xba4/0x11f0 [<0000000083477587>] ip_make_skb+0x14c/0x1a8 [<0000000024f3d592>] udp_sendmsg+0xaf0/0xcf0 [<000000005aabe255>] inet_sendmsg+0x5c/0x80 [<000000008651ea08>] __sys_sendto+0x15c/0x218 [<000000003505c99b>] __arm64_sys_sendto+0x74/0x90 [<00000000263486ec>] el0_svc_handler+0xd0/0x1a0 [<0000000005b5157d>] el0_svc+0x8/0xc Fixes: 2bdaf386 (mac80211: mesh: move path tables into if_mesh) Signed-off-by:Remi Pommarel <repk@triplefau.lt> Link: https://lore.kernel.org/r/20200704135419.27703-1-repk@triplefau.ltSigned-off-by:
-
Remi Pommarel authored
At ieee80211_join_mesh() some ie data could have been allocated (see copy_mesh_setup()) and need to be cleaned up when leaving the mesh. This fixes the following kmemleak report: unreferenced object 0xffff0000116bc600 (size 128): comm "wpa_supplicant", pid 608, jiffies 4294898983 (age 293.484s) hex dump (first 32 bytes): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 0............... 00 0f ac 08 00 00 00 00 c4 65 40 00 00 00 00 00 .........e@..... backtrace: [<00000000bebe439d>] __kmalloc_track_caller+0x1c0/0x330 [<00000000a349dbe1>] kmemdup+0x28/0x50 [<0000000075d69baa>] ieee80211_join_mesh+0x6c/0x3b8 [mac80211] [<00000000683bb98b>] __cfg80211_join_mesh+0x1e8/0x4f0 [cfg80211] [<0000000072cb507f>] nl80211_join_mesh+0x520/0x6b8 [cfg80211] [<0000000077e9bcf9>] genl_family_rcv_msg+0x374/0x680 [<00000000b1bd936d>] genl_rcv_msg+0x78/0x108 [<0000000022c53788>] netlink_rcv_skb+0xb0/0x1c0 [<0000000011af8ec9>] genl_rcv+0x34/0x48 [<0000000069e41f53>] netlink_unicast+0x268/0x2e8 [<00000000a7517316>] netlink_sendmsg+0x320/0x4c0 [<0000000069cba205>] ____sys_sendmsg+0x354/0x3a0 [<00000000e06bab0f>] ___sys_sendmsg+0xd8/0x120 [<0000000037340728>] __sys_sendmsg+0xa4/0xf8 [<000000004fed9776>] __arm64_sys_sendmsg+0x44/0x58 [<000000001c1e5647>] el0_svc_handler+0xd0/0x1a0 Fixes: c80d545d (mac80211: Let userspace enable and configure vendor specific path selection.) Signed-off-by: -
Rajkumar Manoharan authored
The commit 24a2042c ("mac80211: add HE 6 GHz Band Capability element") failed to check device capability before adding HE 6 GHz capability element. Below warning is reported in 11ac device in mesh. Fix that by checking device capability at HE 6 GHz cap IE addition in mesh beacon and association request. WARNING: CPU: 1 PID: 1897 at net/mac80211/util.c:2878 ieee80211_ie_build_he_6ghz_cap+0x149/0x150 [mac80211] [ 3138.720358] Call Trace: [ 3138.720361] ieee80211_mesh_build_beacon+0x462/0x530 [mac80211] [ 3138.720363] ieee80211_start_mesh+0xa8/0xf0 [mac80211] [ 3138.720365] __cfg80211_join_mesh+0x122/0x3e0 [cfg80211] [ 3138.720368] nl80211_join_mesh+0x3d3/0x510 [cfg80211] Fixes: 24a2042c ("mac80211: add HE 6 GHz Band Capability element") Reported-by:
Markus Theil <markus.theil@tu-ilmenau.de> Signed-off-by:
Rajkumar Manoharan <rmanohar@codeaurora.org> Link: https://lore.kernel.org/r/1593656424-18240-1-git-send-email-rmanohar@codeaurora.orgSigned-off-by:
-
- 29 Jul, 2020 22 commits
-
-
Thomas Falcon authored
RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ error paths. Fix this and dispose of TX IRQ mappings correctly in case of an error. Fixes: ea22d51a ("ibmvnic: simplify and improve driver probe function") Signed-off-by:
Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw fixes This patch set contains various fixes for mlxsw. Patches #1-#2 fix two trap related issues introduced in previous cycle. Patches #3-#5 fix rare use-after-frees discovered by syzkaller. After over a week of fuzzing with the fixes, the bugs did not reproduce. Patch #6 from Amit fixes an issue in the ethtool selftest that was recently discovered after running the test on a new platform that supports only 1Gbps and 10Gbps speeds. ==================== Signed-off-by: -
Amit Cohen authored
The test case check_highest_speed_is_chosen() configures $h1 to advertise a subset of its supported speeds and checks that $h2 chooses the highest speed from the subset. To find the common advertised speeds between $h1 and $h2, common_speeds_get() is called. Currently, the first speed returned from common_speeds_get() is removed claiming "h1 does not advertise this speed". The claim is wrong because the function is called after $h1 already advertised a subset of speeds. In case $h1 supports only two speeds, it will advertise a single speed which will be later removed because of previously mentioned bug. This results in the test needlessly failing. When more than two speeds are supported this is not an issue because the first advertised speed is the lowest one. Fix this by not removing any speed from the list of commonly advertised speeds. Fixes: 64916b57 ("selftests: forwarding: Add speed and auto-negotiation test") Reported-by:
Danielle Ratson <danieller@mellanox.com> Signed-off-by:
Amit Cohen <amitc@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
Several notifiers are registered as part of router initialization. Since some of these notifiers are registered before the end of the initialization, it is possible for them to access uninitialized or freed memory when processing notifications [1]. Additionally, some of these notifiers queue work items on a workqueue. If these work items are executed after the router was de-initialized, they will access freed memory. Fix both problems by moving the registration of the notifiers to the end of the router initialization and flush the work queue after they are unregistered. [1] BUG: KASAN: use-after-free in __mutex_lock_common kernel/locking/mutex.c:938 [inline] BUG: KASAN: use-after-free in __mutex_lock+0xeea/0x1340 kernel/locking/mutex.c:1103 Read of size 8 at addr ffff888038c3a6e0 by task kworker/u4:1/61 CPU: 1 PID: 61 Comm: kworker/u4:1 Not tainted 5.8.0-rc2+ #36 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: mlxsw_core_ordered mlxsw_sp_inet6addr_event_work Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xf6/0x16e lib/dump_stack.c:118 print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383 __kasan_report mm/kasan/report.c:513 [inline] kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530 __mutex_lock_common kernel/locking/mutex.c:938 [inline] __mutex_lock+0xeea/0x1340 kernel/locking/mutex.c:1103 mlxsw_sp_inet6addr_event_work+0xb3/0x1b0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7123 process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269 worker_thread+0x9e/0x1050 kernel/workqueue.c:2415 kthread+0x355/0x470 kernel/kthread.c:291 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293 Allocated by task 1298: save_stack+0x1b/0x40 mm/kasan/common.c:48 set_track mm/kasan/common.c:56 [inline] __kasan_kmalloc mm/kasan/common.c:494 [inline] __kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467 kmalloc include/linux/slab.h:555 [inline] kzalloc include/linux/slab.h:669 [inline] mlxsw_sp_router_init+0xb2/0x1d20 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:8074 mlxsw_sp_init+0xbd8/0x3ac0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2932 __mlxsw_core_bus_device_register+0x657/0x10d0 drivers/net/ethernet/mellanox/mlxsw/core.c:1375 mlxsw_core_bus_device_register drivers/net/ethernet/mellanox/mlxsw/core.c:1436 [inline] mlxsw_devlink_core_bus_device_reload_up+0xcd/0x150 drivers/net/ethernet/mellanox/mlxsw/core.c:1133 devlink_reload net/core/devlink.c:2959 [inline] devlink_reload+0x281/0x3b0 net/core/devlink.c:2944 devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987 genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline] genl_family_rcv_msg net/netlink/genetlink.c:736 [inline] genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753 netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469 genl_rcv+0x24/0x40 net/netlink/genetlink.c:764 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline] netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329 netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0x150/0x190 net/socket.c:672 ____sys_sendmsg+0x6d8/0x840 net/socket.c:2363 ___sys_sendmsg+0xff/0x170 net/socket.c:2417 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2450 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Freed by task 1348: save_stack+0x1b/0x40 mm/kasan/common.c:48 set_track mm/kasan/common.c:56 [inline] kasan_set_free_info mm/kasan/common.c:316 [inline] __kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455 slab_free_hook mm/slub.c:1474 [inline] slab_free_freelist_hook mm/slub.c:1507 [inline] slab_free mm/slub.c:3072 [inline] kfree+0xe6/0x320 mm/slub.c:4063 mlxsw_sp_fini+0x340/0x4e0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3132 mlxsw_core_bus_device_unregister+0x16c/0x6d0 drivers/net/ethernet/mellanox/mlxsw/core.c:1474 mlxsw_devlink_core_bus_device_reload_down+0x8e/0xc0 drivers/net/ethernet/mellanox/mlxsw/core.c:1123 devlink_reload+0xc6/0x3b0 net/core/devlink.c:2952 devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987 genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline] genl_family_rcv_msg net/netlink/genetlink.c:736 [inline] genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753 netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469 genl_rcv+0x24/0x40 net/netlink/genetlink.c:764 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline] netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329 netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0x150/0x190 net/socket.c:672 ____sys_sendmsg+0x6d8/0x840 net/socket.c:2363 ___sys_sendmsg+0xff/0x170 net/socket.c:2417 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2450 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359 entry_SYSCALL_64_after_hwframe+0x44/0xa9 The buggy address belongs to the object at ffff888038c3a000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1760 bytes inside of 2048-byte region [ffff888038c3a000, ffff888038c3a800) The buggy address belongs to the page: page:ffffea0000e30e00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 head:ffffea0000e30e00 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x100000000010200(slab|head) raw: 0100000000010200 dead000000000100 dead000000000122 ffff88806c40c000 raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888038c3a580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888038c3a600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff888038c3a680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888038c3a700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888038c3a780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 965fa8e6 ("mlxsw: spectrum_router: Make RIF deletion more robust") Signed-off-by:Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
The lifetime of EMAD transactions (i.e., 'struct mlxsw_reg_trans') is managed using RCU. They are freed using kfree_rcu() once the transaction ends. However, in case the transaction failed it is freed immediately after being removed from the active transactions list. This is problematic because it is still possible for a different CPU to dereference the transaction from an RCU read-side critical section while traversing the active transaction list in mlxsw_emad_rx_listener_func(). In which case, a use-after-free is triggered [1]. Fix this by freeing the transaction after a grace period by calling kfree_rcu(). [1] BUG: KASAN: use-after-free in mlxsw_emad_rx_listener_func+0x969/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:671 Read of size 8 at addr ffff88800b7964e8 by task syz-executor.2/2881 CPU: 0 PID: 2881 Comm: syz-executor.2 Not tainted 5.8.0-rc4+ #44 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xf6/0x16e lib/dump_stack.c:118 print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383 __kasan_report mm/kasan/report.c:513 [inline] kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530 mlxsw_emad_rx_listener_func+0x969/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:671 mlxsw_core_skb_receive+0x571/0x700 drivers/net/ethernet/mellanox/mlxsw/core.c:2061 mlxsw_pci_cqe_rdq_handle drivers/net/ethernet/mellanox/mlxsw/pci.c:595 [inline] mlxsw_pci_cq_tasklet+0x12a6/0x2520 drivers/net/ethernet/mellanox/mlxsw/pci.c:651 tasklet_action_common.isra.0+0x13f/0x3e0 kernel/softirq.c:550 __do_softirq+0x223/0x964 kernel/softirq.c:292 asm_call_on_stack+0x12/0x20 arch/x86/entry/entry_64.S:711 </IRQ> __run_on_irqstack arch/x86/include/asm/irq_stack.h:22 [inline] run_on_irqstack_cond arch/x86/include/asm/irq_stack.h:48 [inline] do_softirq_own_stack+0x109/0x140 arch/x86/kernel/irq_64.c:77 invoke_softirq kernel/softirq.c:387 [inline] __irq_exit_rcu kernel/softirq.c:417 [inline] irq_exit_rcu+0x16f/0x1a0 kernel/softirq.c:429 sysvec_apic_timer_interrupt+0x4e/0xd0 arch/x86/kernel/apic/apic.c:1091 asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:587 RIP: 0010:arch_local_irq_restore arch/x86/include/asm/irqflags.h:85 [inline] RIP: 0010:__raw_spin_unlock_irqrestore include/linux/spinlock_api_smp.h:160 [inline] RIP: 0010:_raw_spin_unlock_irqrestore+0x3b/0x40 kernel/locking/spinlock.c:191 Code: e8 2a c3 f4 fc 48 89 ef e8 12 96 f5 fc f6 c7 02 75 11 53 9d e8 d6 db 11 fd 65 ff 0d 1f 21 b3 56 5b 5d c3 e8 a7 d7 11 fd 53 9d <eb> ed 0f 1f 00 55 48 89 fd 65 ff 05 05 21 b3 56 ff 74 24 08 48 8d RSP: 0018:ffff8880446ffd80 EFLAGS: 00000286 RAX: 0000000000000006 RBX: 0000000000000286 RCX: 0000000000000006 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffa94ecea9 RBP: ffff888012934408 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: fffffbfff57be301 R12: 1ffff110088dffc1 R13: ffff888037b817c0 R14: ffff88802442415a R15: ffff888024424000 __do_sys_perf_event_open+0x1b5d/0x2bd0 kernel/events/core.c:11874 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:384 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x473dbd Code: Bad RIP value. RSP: 002b:00007f21e5e9cc28 EFLAGS: 00000246 ORIG_RAX: 000000000000012a RAX: ffffffffffffffda RBX: 000000000057bf00 RCX: 0000000000473dbd RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000040 RBP: 000000000057bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000003 R11: 0000000000000246 R12: 000000000057bf0c R13: 00007ffd0493503f R14: 00000000004d0f46 R15: 00007f21e5e9cd80 Allocated by task 871: save_stack+0x1b/0x40 mm/kasan/common.c:48 set_track mm/kasan/common.c:56 [inline] __kasan_kmalloc mm/kasan/common.c:494 [inline] __kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467 kmalloc include/linux/slab.h:555 [inline] kzalloc include/linux/slab.h:669 [inline] mlxsw_core_reg_access_emad+0x70/0x1410 drivers/net/ethernet/mellanox/mlxsw/core.c:1812 mlxsw_core_reg_access+0xeb/0x540 drivers/net/ethernet/mellanox/mlxsw/core.c:1991 mlxsw_sp_port_get_hw_xstats+0x335/0x7e0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1130 update_stats_cache+0xf4/0x140 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1173 process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269 worker_thread+0x9e/0x1050 kernel/workqueue.c:2415 kthread+0x355/0x470 kernel/kthread.c:291 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293 Freed by task 871: save_stack+0x1b/0x40 mm/kasan/common.c:48 set_track mm/kasan/common.c:56 [inline] kasan_set_free_info mm/kasan/common.c:316 [inline] __kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455 slab_free_hook mm/slub.c:1474 [inline] slab_free_freelist_hook mm/slub.c:1507 [inline] slab_free mm/slub.c:3072 [inline] kfree+0xe6/0x320 mm/slub.c:4052 mlxsw_core_reg_access_emad+0xd45/0x1410 drivers/net/ethernet/mellanox/mlxsw/core.c:1819 mlxsw_core_reg_access+0xeb/0x540 drivers/net/ethernet/mellanox/mlxsw/core.c:1991 mlxsw_sp_port_get_hw_xstats+0x335/0x7e0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1130 update_stats_cache+0xf4/0x140 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1173 process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269 worker_thread+0x9e/0x1050 kernel/workqueue.c:2415 kthread+0x355/0x470 kernel/kthread.c:291 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293 The buggy address belongs to the object at ffff88800b796400 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 232 bytes inside of 512-byte region [ffff88800b796400, ffff88800b796600) The buggy address belongs to the page: page:ffffea00002de500 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 head:ffffea00002de500 order:2 compound_mapcount:0 compound_pincount:0 flags: 0x100000000010200(slab|head) raw: 0100000000010200 dead000000000100 dead000000000122 ffff88806c402500 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88800b796380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800b796400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88800b796480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88800b796500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800b796580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: caf7297e ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: -
Ido Schimmel authored
The lifetime of the Rx listener item ('rxl_item') is managed using RCU, but is dereferenced outside of RCU read-side critical section, which can lead to a use-after-free. Fix this by increasing the scope of the RCU read-side critical section. Fixes: 93c1edb2 ("mlxsw: Introduce Mellanox switch driver core") Signed-off-by: -
Ido Schimmel authored
Cited commit mistakenly removed the trap group for externally routed packets (e.g., via the management interface) and grouped locally routed and externally routed packet traps under the same group, thereby subjecting them to the same policer. This can result in problems, for example, when FRR is restarted and suddenly all transient traffic is trapped to the CPU because of a default route through the management interface. Locally routed packets required to re-establish a BGP connection will never reach the CPU and the routing tables will not be re-populated. Fix this by using a different trap group for externally routed packets. Fixes: 8110668e ("mlxsw: spectrum_trap: Register layer 3 control traps") Reported-by:
Alex Veber <alexve@mellanox.com> Tested-by:
-
Ido Schimmel authored
Cited commit added the ability to program link-local prefix routes to the ASIC so that relevant packets are routed and trapped correctly. However, host routes were not included in the change and thus not programmed to the ASIC. This can result in packets being trapped via an external route trap instead of a local route trap as in IPv4. Fix this by programming all the link-local routes to the ASIC. Fixes: 10d3757f ("mlxsw: spectrum_router: Allow programming link-local prefix routes") Reported-by:
-
Ido Schimmel authored
fib_trie_unmerge() is called with RTNL held, but not from an RCU read-side critical section. This leads to the following warning [1] when the FIB alias list in a leaf is traversed with hlist_for_each_entry_rcu(). Since the function is always called with RTNL held and since modification of the list is protected by RTNL, simply use hlist_for_each_entry() and silence the warning. [1] WARNING: suspicious RCU usage 5.8.0-rc4-custom-01520-gc1f937f3f83b #30 Not tainted ----------------------------- net/ipv4/fib_trie.c:1867 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by ip/164: #0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0 stack backtrace: CPU: 0 PID: 164 Comm: ip Not tainted 5.8.0-rc4-custom-01520-gc1f937f3f83b #30 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack+0x100/0x184 lockdep_rcu_suspicious+0x153/0x15d fib_trie_unmerge+0x608/0xdb0 fib_unmerge+0x44/0x360 fib4_rule_configure+0xc8/0xad0 fib_nl_newrule+0x37a/0x1dd0 rtnetlink_rcv_msg+0x4f7/0xbd0 netlink_rcv_skb+0x17a/0x480 rtnetlink_rcv+0x22/0x30 netlink_unicast+0x5ae/0x890 netlink_sendmsg+0x98a/0xf40 ____sys_sendmsg+0x879/0xa00 ___sys_sendmsg+0x122/0x190 __sys_sendmsg+0x103/0x1d0 __x64_sys_sendmsg+0x7d/0xb0 do_syscall_64+0x54/0xa0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7fc80a234e97 Code: Bad RIP value. RSP: 002b:00007ffef8b66798 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc80a234e97 RDX: 0000000000000000 RSI: 00007ffef8b66800 RDI: 0000000000000003 RBP: 000000005f141b1c R08: 0000000000000001 R09: 0000000000000000 R10: 00007fc80a2a8ac0 R11: 0000000000000246 R12: 0000000000000001 R13: 0000000000000000 R14: 00007ffef8b67008 R15: 0000556fccb10020 Fixes: 0ddcf43d ("ipv4: FIB Local/MAIN table collapse") Signed-off-by: -
Ido Schimmel authored
The commit cited below removed the RCU read-side critical section from rtnl_fdb_dump() which means that the ndo_fdb_dump() callback is invoked without RCU protection. This results in the following warning [1] in the VXLAN driver, which relied on the callback being invoked from an RCU read-side critical section. Fix this by calling rcu_read_lock() in the VXLAN driver, as already done in the bridge driver. [1] WARNING: suspicious RCU usage 5.8.0-rc4-custom-01521-g481007553ce6 #29 Not tainted ----------------------------- drivers/net/vxlan.c:1379 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by bridge/166: #0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xea/0x1090 stack backtrace: CPU: 1 PID: 166 Comm: bridge Not tainted 5.8.0-rc4-custom-01521-g481007553ce6 #29 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack+0x100/0x184 lockdep_rcu_suspicious+0x153/0x15d vxlan_fdb_dump+0x51e/0x6d0 rtnl_fdb_dump+0x4dc/0xad0 netlink_dump+0x540/0x1090 __netlink_dump_start+0x695/0x950 rtnetlink_rcv_msg+0x802/0xbd0 netlink_rcv_skb+0x17a/0x480 rtnetlink_rcv+0x22/0x30 netlink_unicast+0x5ae/0x890 netlink_sendmsg+0x98a/0xf40 __sys_sendto+0x279/0x3b0 __x64_sys_sendto+0xe6/0x1a0 do_syscall_64+0x54/0xa0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7fe14fa2ade0 Code: Bad RIP value. RSP: 002b:00007fff75bb5b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00005614b1ba0020 RCX: 00007fe14fa2ade0 RDX: 000000000000011c RSI: 00007fff75bb5b90 RDI: 0000000000000003 RBP: 00007fff75bb5b90 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00005614b1b89160 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Fixes: 5e6d2435 ("bridge: netlink dump interface at par with brctl") Signed-off-by: -
Martin Varghese authored
Removed redundant words. Fixes: 571912c6 ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.") Signed-off-by:
Martin Varghese <martin.varghese@nokia.com> Signed-off-by:
-
Guillaume Nault authored
In multiproto mode, bareudp_xmit() accepts sending multicast MPLS and IPv6 packets regardless of the bareudp ethertype. In practice, this let an IP tunnel send multicast MPLS packets, or an MPLS tunnel send IPv6 packets. We need to restrict the test further, so that the multiproto mode only enables * IPv6 for IPv4 tunnels, * or multicast MPLS for unicast MPLS tunnels. To improve clarity, the protocol validation is moved to its own function, where each logical test has its own condition. v2: s/ntohs/htons/ Fixes: 4b5f6723 ("net: Special handling for IP & MPLS.") Signed-off-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
-
Xiyu Yang authored
ip6_route_info_create() invokes nexthop_get(), which increases the refcount of the "nh". When ip6_route_info_create() returns, local variable "nh" becomes invalid, so the refcount should be decreased to keep refcount balanced. The reference counting issue happens in one exception handling path of ip6_route_info_create(). When nexthops can not be used with source routing, the function forgets to decrease the refcnt increased by nexthop_get(), causing a refcnt leak. Fix this issue by pulling up the error source routing handling when nexthops can not be used with source routing. Fixes: f88d8ea6 ("ipv6: Plumb support for nexthop object in a fib6_info") Signed-off-by:
Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by:
Xin Tan <tanxin.ctf@gmail.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
David S. Miller authored
Subbaraya Sundeep says: ==================== Fix bugs in Octeontx2 netdev driver There are problems in the existing Octeontx2 netdev drivers like missing cancel_work for the reset task, missing lock in reset task and missing unergister_netdev in driver remove. This patch set fixes the above problems. ==================== Signed-off-by: -
Subbaraya Sundeep authored
Added unregister_netdev in the driver remove function. Generally unregister_netdev is called after disabling all the device interrupts but here it is called before disabling device mailbox interrupts. The reason behind this is VF needs mailbox interrupt to communicate with its PF to clean up its resources during otx2_stop. otx2_stop disables packet I/O and queue interrupts first and by using mailbox interrupt communicates to PF to free VF resources. Hence this patch calls unregister_device just before disabling mailbox interrupts. Fixes: 3184fb5b ("octeontx2-vf: Virtual function driver support") Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Signed-off-by:
-
Subbaraya Sundeep authored
During driver exit cancel the queued reset_task work in VF driver. Fixes: 3184fb5b ("octeontx2-vf: Virtual function driver support") Signed-off-by:
-
Subbaraya Sundeep authored
Two bugs exist in the code related to reset_task in PF driver one is the missing protection against network stack ndo_open and ndo_close. Other one is the missing cancel_work. This patch fixes those problems. Fixes: 4ff7d148 ("octeontx2-pf: Error handling support") Signed-off-by:
-
Jakub Kicinski authored
It appears that not disabling a PCI device on .shutdown may lead to a Hardware Error with particular (perhaps buggy) BIOS versions: mlx4_en: eth0: Close port called mlx4_en 0000:04:00.0: removed PHC reboot: Restarting system {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1 {1}[Hardware Error]: event severity: fatal {1}[Hardware Error]: Error 0, type: fatal {1}[Hardware Error]: section_type: PCIe error {1}[Hardware Error]: port_type: 4, root port {1}[Hardware Error]: version: 1.16 {1}[Hardware Error]: command: 0x4010, status: 0x0143 {1}[Hardware Error]: device_id: 0000:00:02.2 {1}[Hardware Error]: slot: 0 {1}[Hardware Error]: secondary_bus: 0x04 {1}[Hardware Error]: vendor_id: 0x8086, device_id: 0x2f06 {1}[Hardware Error]: class_code: 000604 {1}[Hardware Error]: bridge: secondary_status: 0x2000, control: 0x0003 {1}[Hardware Error]: aer_uncor_status: 0x00100000, aer_uncor_mask: 0x00000000 {1}[Hardware Error]: aer_uncor_severity: 0x00062030 {1}[Hardware Error]: TLP Header: 40000018 040000ff 791f4080 00000000 [hw error repeats] Kernel panic - not syncing: Fatal hardware error! CPU: 0 PID: 2189 Comm: reboot Kdump: loaded Not tainted 5.6.x-blabla #1 Hardware name: HP ProLiant DL380 Gen9/ProLiant DL380 Gen9, BIOS P89 05/05/2017 Fix the mlx4 driver. This is a very similar problem to what had been fixed in: commit 0d98ba8d ("scsi: hpsa: disable device during shutdown") to address https://bugzilla.kernel.org/show_bug.cgi?id=199779. Fixes: 2ba5fbd6 ("net/mlx4_core: Handle AER flow properly") Reported-by:Jake Lawrence <lawja@fb.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Reviewed-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
David S. Miller authored
Herbert Xu says: ==================== rhashtable: Fix unprotected RCU dereference in __rht_ptr This patch series fixes an unprotected dereference in __rht_ptr. The first patch is a minimal fix that does not use the correct RCU markings but is suitable for backport, and the second patch cleans up the RCU markings. ==================== Signed-off-by: -
Herbert Xu authored
This patch restores the RCU marking on bucket_table->buckets as it really does need RCU protection. Its removal had led to a fatal bug. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
The rcu_dereference call in rht_ptr_rcu is completely bogus because we've already dereferenced the value in __rht_ptr and operated on it. This causes potential double readings which could be fatal. The RCU dereference must occur prior to the comparison in __rht_ptr. This patch changes the order of RCU dereference so that it is done first and the result is then fed to __rht_ptr. The RCU marking changes have been minimised using casts which will be removed in a follow-up patch. Fixes: ba6306e3 ("rhashtable: Remove RCU marking from...") Reported-by:
"Gong, Sishuai" <sishuai@purdue.edu> Signed-off-by:
-
René van Dorst authored
Modify mtk_gmac0_rgmii_adjust() so it can always be called. mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks. Signed-off-by:
René van Dorst <opensource@vdorst.com> Signed-off-By:
David Woodhouse <dwmw2@infradead.org> Tested-by:
Frank Wunderlich <frank-w@public-files.de> Signed-off-by:
-
- 28 Jul, 2020 12 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5 fixes-2020-07-28 This series introduces some fixes to mlx5 driver. v1->v2: - Drop the "Hold reference on mirred devices" patch, until Or's comments are addressed. - Imporve "Modify uplink state" patch commit message per Or's request. Please pull and let me know if there is any problem. For -Stable: For -stable v4.9 ('net/mlx5e: Fix error path of device attach') For -stable v4.15 ('net/mlx5: Verify Hardware supports requested ptp function on a given pin') For -stable v5.3 ('net/mlx5e: Modify uplink state on interface up/down') For -stable v5.4 ('net/mlx5e: Fix kernel crash when setting vf VLANID on a VF dev') ('net/mlx5: E-switch, Destroy TSAR when fail to enable the mode') For -stable v5.5 ('net/mlx5: E-switch, Destroy TSAR after reload interface') For -stable v5.7 ('net/mlx5: Fix a bug of using ptp channel index as pin index') ==================== Acked-by: -
David S. Miller authored
Johan Hovold says: ==================== net: lan78xx: fix NULL deref and memory leak The first two patches fix a NULL-pointer dereference at probe that can be triggered by a malicious device and a small transfer-buffer memory leak, respectively. For another subsystem I would have marked them: Cc: stable@vger.kernel.org # 4.3 The third one replaces the driver's current broken endpoint lookup helper, which could end up accepting incomplete interfaces and whose results weren't even useeren Johan ==================== Signed-off-by: -
Johan Hovold authored
Drop the bogus endpoint-lookup helper which could end up accepting interfaces based on endpoints belonging to unrelated altsettings. Note that the returned bulk pipes and interrupt endpoint descriptor were never actually used. Instead the bulk-endpoint numbers are hardcoded to 1 and 2 (matching the specification), while the interrupt- endpoint descriptor was assumed to be the third descriptor created by USB core. Try to bring some order to this by dropping the bogus lookup helper and adding the missing endpoint sanity checks while keeping the interrupt- descriptor assumption for now. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
The interrupt URB transfer-buffer was never freed on disconnect or after probe errors. Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com> Signed-off-by:
-
Johan Hovold authored
Add the missing endpoint sanity check to prevent a NULL-pointer dereference should a malicious device lack the expected endpoints. Note that the driver has a broken endpoint-lookup helper, lan78xx_get_endpoints(), which can end up accepting interfaces in an altsetting without endpoints as long as *some* altsetting has a bulk-in and a bulk-out endpoint. Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com> Signed-off-by:
-
Rustam Kovhaev authored
in case of an error tty_register_device_attr() returns ERR_PTR(), add IS_ERR() check Reported-and-tested-by: syzbot+67b2bd0e34f952d0321e@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=67b2bd0e34f952d0321eSigned-off-by:
Rustam Kovhaev <rkovhaev@gmail.com> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Alaa Hleihel authored
After the cited commit, function 'mlx5_eswitch_set_vport_vlan' started to acquire esw->state_lock. However, esw is not defined for VF devices, hence attempting to set vf VLANID on a VF dev will cause a kernel panic. Fix it by moving up the (redundant) esw validation from function '__mlx5_eswitch_set_vport_vlan' since the rest of the callers now have and use a valid esw. For example with vf device eth4: # ip link set dev eth4 vf 0 vlan 0 Trace of the panic: [ 411.409842] BUG: unable to handle page fault for address: 00000000000011b8 [ 411.449745] #PF: supervisor read access in kernel mode [ 411.452348] #PF: error_code(0x0000) - not-present page [ 411.454938] PGD 80000004189c9067 P4D 80000004189c9067 PUD 41899a067 PMD 0 [ 411.458382] Oops: 0000 [#1] SMP PTI [ 411.460268] CPU: 4 PID: 5711 Comm: ip Not tainted 5.8.0-rc4_for_upstream_min_debug_2020_07_08_22_04 #1 [ 411.462447] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 411.464158] RIP: 0010:__mutex_lock+0x4e/0x940 [ 411.464928] Code: fd 41 54 49 89 f4 41 52 53 89 d3 48 83 ec 70 44 8b 1d ee 03 b0 01 65 48 8b 04 25 28 00 00 00 48 89 45 c8 31 c0 45 85 db 75 0a <48> 3b 7f 60 0f 85 7e 05 00 00 49 8d 45 68 41 56 41 b8 01 00 00 00 [ 411.467678] RSP: 0018:ffff88841fcd74b0 EFLAGS: 00010246 [ 411.468562] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 [ 411.469715] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000001158 [ 411.470812] RBP: ffff88841fcd7550 R08: ffffffffa00fa1ce R09: 0000000000000000 [ 411.471835] R10: ffff88841fcd7570 R11: 0000000000000000 R12: 0000000000000002 [ 411.472862] R13: 0000000000001158 R14: ffffffffa00fa1ce R15: 0000000000000000 [ 411.474004] FS: 00007faee7ca6b80(0000) GS:ffff88846fc00000(0000) knlGS:0000000000000000 [ 411.475237] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 411.476129] CR2: 00000000000011b8 CR3: 000000041909c006 CR4: 0000000000360ea0 [ 411.477260] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 411.478340] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 411.479332] Call Trace: [ 411.479760] ? __nla_validate_parse.part.6+0x57/0x8f0 [ 411.482825] ? mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core] [ 411.483804] mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core] [ 411.484733] mlx5e_set_vf_vlan+0x41/0x50 [mlx5_core] [ 411.485545] do_setlink+0x613/0x1000 [ 411.486165] __rtnl_newlink+0x53d/0x8c0 [ 411.486791] ? mark_held_locks+0x49/0x70 [ 411.487429] ? __lock_acquire+0x8fe/0x1eb0 [ 411.488085] ? rcu_read_lock_sched_held+0x52/0x60 [ 411.488998] ? kmem_cache_alloc_trace+0x16d/0x2d0 [ 411.489759] rtnl_newlink+0x47/0x70 [ 411.490357] rtnetlink_rcv_msg+0x24e/0x450 [ 411.490978] ? netlink_deliver_tap+0x92/0x3d0 [ 411.491631] ? validate_linkmsg+0x330/0x330 [ 411.492262] netlink_rcv_skb+0x47/0x110 [ 411.492852] netlink_unicast+0x1ac/0x270 [ 411.493551] netlink_sendmsg+0x336/0x450 [ 411.494209] sock_sendmsg+0x30/0x40 [ 411.494779] ____sys_sendmsg+0x1dd/0x1f0 [ 411.495378] ? copy_msghdr_from_user+0x5c/0x90 [ 411.496082] ___sys_sendmsg+0x87/0xd0 [ 411.496683] ? lock_acquire+0xb9/0x3a0 [ 411.497322] ? lru_cache_add+0x5/0x170 [ 411.497944] ? find_held_lock+0x2d/0x90 [ 411.498568] ? handle_mm_fault+0xe46/0x18c0 [ 411.499205] ? __sys_sendmsg+0x51/0x90 [ 411.499784] __sys_sendmsg+0x51/0x90 [ 411.500341] do_syscall_64+0x59/0x2e0 [ 411.500938] ? asm_exc_page_fault+0x8/0x30 [ 411.501609] ? rcu_read_lock_sched_held+0x52/0x60 [ 411.502350] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 411.503093] RIP: 0033:0x7faee73b85a7 [ 411.503654] Code: Bad RIP value. Fixes: 0e18134f ("net/mlx5e: Eswitch, use state_lock to synchronize vlan change") Signed-off-by:
Alaa Hleihel <alaa@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Vlad Buslov <vladbu@mellanox.com> Signed-off-by:
-
Ron Diskin authored
When setting the PF interface up/down, notify the firmware to update uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled. This behavior will prevent sending traffic out on uplink port when PF is down, such as sending traffic from a VF interface which is still up. Currently when calling mlx5e_open/close(), the driver only sends PAOS command to notify the firmware to set the physical port state to up/down, however, it is not sufficient. When VF is in "auto" state, it follows the uplink state, which was not updated on mlx5e_open/close() before this patch. When switchdev mode is enabled and uplink representor is first enabled, set the uplink port state value back to its FW default "AUTO". Fixes: 63bfd399 ("net/mlx5e: Send PAOS command on interface up/down") Signed-off-by:
Ron Diskin <rondi@mellanox.com> Reviewed-by:
Moshe Shemesh <moshe@mellanox.com> Signed-off-by:
-
Eran Ben Elisha authored
In a special configuration, a ConnectX6-Dx pin pps-out might be activated when driver is loaded. Fix the driver to always read the operational pin mode when registering it, and advertise it accordingly. Fixes: ee7f1220 ("net/mlx5e: Implement 1PPS support") Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Raed Salem authored
mlx5e_rep_is_lag_netdev is used as first check as part of netdev events handler for bond device of non-uplink representors, this handler can get any netdevice under the same network namespace of mlx5e netdevice. Current code treats the netdev as mlx5e netdev and only later on verifies this, hence causes the following Kasan trace: [15402.744990] ================================================================== [15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core] [15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347 [15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G B O --------- -t - 4.18.0-g3dcc204d291d-dirty #1 [15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [15402.757600] Call Trace: [15402.758968] dump_stack+0x71/0xab [15402.760427] print_address_description+0x6a/0x270 [15402.761969] kasan_report+0x179/0x2d0 [15402.763445] ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core] [15402.765121] mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core] [15402.766782] mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core] Fix by deferring the violating access to be post the netdev verify check. Fixes: 7e51891a ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule") Signed-off-by:
Raed Salem <raeds@mellanox.com> Reviewed-by:
Vu Pham <vuhuong@mellanox.com> Signed-off-by:
-
Eran Ben Elisha authored
Fix a bug where driver did not verify Hardware pin capabilities for PTP functions. Fixes: ee7f1220 ("net/mlx5e: Implement 1PPS support") Signed-off-by:
Ariel Levkovich <lariel@mellanox.com> Signed-off-by:
-
Eran Ben Elisha authored
On PTP mlx5_ptp_enable(on=0) flow, driver mistakenly used channel index as pin index. After ptp patch marked in fixes tag was introduced, driver can freely call ptp_find_pin() as part of the .enable() callback. Fix driver mlx5_ptp_enable(on=0) flow to always use ptp_find_pin(). With that, Driver will use the correct pin index in mlx5_ptp_enable(on=0) flow. In addition, when initializing the pins, always set channel to zero. As all pins can be attached to all channels, let ptp_set_pinfunc() to move them between the channels. For stable branches, this fix to be applied only on kernels that includes both patches in fixes tag. Otherwise, mlx5_ptp_enable(on=0) will be stuck on pincfg_mux. Fixes: 62582a7e ("ptp: Avoid deadlocks in the programmable pin code.") Fixes: ee7f1220 ("net/mlx5e: Implement 1PPS support") Signed-off-by:
-
