A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:

drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
    cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
    cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.

Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.

In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.

If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.

This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.

Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.

Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.

Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.

Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

RDS/IB tries to refill the recv buffer in softirq context using
GFP_NOWAIT flag. However alloc failure is handled by queueing a work to
refill the recv buffer with GFP_KERNEL flag. This means failure to
allocate with GFP_NOWAIT isn't fatal. Do not print the PAF warnings if
softirq context fails to refill the recv buffer. We will see the PAF
warnings when worker also fails to allocate.
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Reviewed-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Moshe Shemesh says:

====================
Add devlink reload action and limit options

Introduce new options on devlink reload API to enable the user to select
the reload action required and constrains limits on these actions that he
may want to ensure. Complete support for reload actions in mlx5.
The following reload actions are supported:
  driver_reinit: driver entities re-initialization, applying devlink-param
                 and devlink-resource values.
  fw_activate: firmware activate.

The uAPI is backward compatible, if the reload action option is omitted
from the reload command, the driver reinit action will be used.
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.

By default reload actions are not limited and driver implementation may
include reset or downtime as needed to perform the actions.
However, if reload limit is selected, the driver should perform only if
it can do it while keeping the limit constraints.
Reload limit added:
  no_reset: No reset allowed, no down time allowed, no link flap and no
            configuration is lost.

Each driver which supports devlink reload command should expose the
reload actions and limits supported.

Add reload stats to hold the history per reload action per limit.
For example, the number of times fw_activate has been done on this
device since the driver module was added or if the firmware activation
was done with or without reset.

Patch 1 changes devlink_reload_supported() param type to enable using
        it before allocating devlink.
Patch 2-3 add the new API reload action and reload limit options to
          devlink reload.
Patch 4-5 add reload stats and remote reload stats. These stats are
          exposed through devlink dev get.
Patches 6-11 add support on mlx5 for devlink reload action fw_activate
            and handle the firmware reset events.
Patches 12-13 add devlink enable remote dev reset parameter and use it
             in mlx5.
Patches 14-15 mlx5 add devlink reload limit no_reset support for
              fw_activate reload action.
Patch 16 adds documentation file devlink-reload.rst
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add devlink reload rst documentation file.
Update index file to include it.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for devlink reload action fw_activate with reload limit
no_reset which does firmware live patching, updating the firmware image
without reset, no downtime and no configuration lose. The driver checks
if the firmware is capable of handling the pending firmware changes as a
live patch. If it is then it triggers firmware live patching flow.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The enable_remote_dev_reset devlink param flags that the host admin
allows resets by other hosts. In case it is cleared mlx5 host PF driver
will send NACK on pci sync for firmware update reset request and the
command will fail.
By default enable_remote_dev_reset parameter is true, so pci sync for
firmware update reset is enabled.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The enable_remote_dev_reset devlink param flags that the host admin
allows device resets that can be initiated by other hosts. This
parameter is useful for setups where a device is shared by different
hosts, such as multi-host setup. Once the user set this parameter to
false, the driver should NACK any attempt to reset the device while the
driver is loaded.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Set capability to notify the firmware that this host driver is capable
of handling pci sync for firmware update events.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add functions to query and set the MFRL reset options supported by
firmware.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add remote reload stats to hold the history of actions performed due
devlink reload commands initiated by remote host. For example, in case
firmware activation with reset finished successfully but was initiated
by remote host.

The function devlink_remote_reload_actions_performed() is exported to
enable drivers update on remote reload actions performed as it was not
initiated by their own devlink instance.

Expose devlink remote reload stats to the user through devlink dev get
command.

Examples:
$ devlink dev show
pci/0000:82:00.0:
  stats:
      reload:
        driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
      remote_reload:
        driver_reinit 0 fw_activate 0 fw_activate_no_reset 0
pci/0000:82:00.1:
  stats:
      reload:
        driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
      remote_reload:
        driver_reinit 1 fw_activate 1 fw_activate_no_reset 0

$ devlink dev show -jp
{
    "dev": {
        "pci/0000:82:00.0": {
            "stats": {
                "reload": {
                    "driver_reinit": 2,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                },
                "remote_reload": {
                    "driver_reinit": 0,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                }
            }
        },
        "pci/0000:82:00.1": {
            "stats": {
                "reload": {
                    "driver_reinit": 1,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                },
                "remote_reload": {
                    "driver_reinit": 1,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                }
            }
        }
    }
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add reload stats to hold the history per reload action type and limit.

For example, the number of times fw_activate has been performed on this
device since the driver module was added or if the firmware activation
was performed with or without reset.

Add devlink notification on stats update.

Expose devlink reload stats to the user through devlink dev get command.

Examples:
$ devlink dev show
pci/0000:82:00.0:
  stats:
      reload:
        driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
pci/0000:82:00.1:
  stats:
      reload:
        driver_reinit 1 fw_activate 0 fw_activate_no_reset 0

$ devlink dev show -jp
{
    "dev": {
        "pci/0000:82:00.0": {
            "stats": {
                "reload": {
                    "driver_reinit": 2,
                    "fw_activate": 1,
                    "fw_activate_no_reset": 0
                }
            }
        },
        "pci/0000:82:00.1": {
            "stats": {
                "reload": {
                    "driver_reinit": 1,
                    "fw_activate": 0,
                    "fw_activate_no_reset": 0
                }
            }
        }
    }
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
          configuration is lost.

By default reload limit is unspecified and so no constraints on reload
actions are required.

Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.

The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.

Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
               and devlink-resource values.
fw_activate: firmware activate.

command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
  driver_reinit

$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
  driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Change devlink_reload_supported() function to get devlink_ops pointer
param instead of devlink pointer param.
This change will be used in the next patch to check if devlink reload is
supported before devlink instance is allocated.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

kmalloc() of sufficiently big portion of memory is cache-aligned
in regular conditions. If some debugging options are used,
there is no reason qdisc structures would need 64-byte alignment
if most other kernel structures are not aligned.

This get rid of QDISC_ALIGN and QDISC_ALIGNTO.

Addition of privdata field will help implementing
the reverse of qdisc_priv() and documents where
the private data is.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case of errors, this message was printed:

  (...)
  balanced bwidth with unbalanced delay       5233 max 5005  [ fail ]
  client exit code 0, server 0
  \nnetns ns3-0-EwnkPH socket stat for 10003:
  (...)

Obviously, the idea was to add a new line before the socket stat and not
print "\nnetns".

The commit 8b974778 ("selftests: mptcp: interpret \n as a new line")
is very similar to this one. But the modification in simult_flows.sh was
missed because this commit above was done in parallel to one here below.

Fixes: 1a418cb8 ("mptcp: simult flow self-tests")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Without these definitions, the driver will crash in:
mscc_ocelot_probe
-> ocelot_init
   -> ocelot_vcap_init
     -> __ocelot_target_read_ix

I missed this because I did not have the VSC7514 hardware to test, only
the VSC9959 and VSC9953, and the probing part is different.

Fixes: e3aea296 ("net: mscc: ocelot: add definitions for VCAP ES0 keys, actions and target")
Fixes: a61e365d ("net: mscc: ocelot: add definitions for VCAP IS1 keys, actions and target")
Reported-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If recvmsg() and the workqueue race to dequeue the data
pending on some subflow, the current mapping for such
subflow covers several skbs and some of them have not
reached yet the received, either the worker or recvmsg()
can find a subflow with the data_avail flag set - since
the current mapping is valid and in sequence - but no
skbs in the receive queue - since the other entity just
processed them.

The above will lead to an unbounded loop in __mptcp_move_skbs()
and a subsequent hang of any task trying to acquiring the msk
socket lock.

This change addresses the issue stopping the __mptcp_move_skbs()
loop as soon as we detect the above race (empty receive queue
with data_avail set).

Reported-and-tested-by: syzbot+fcf8ca5817d6e92c6567@syzkaller.appspotmail.com
Fixes: ab174ad8 ("mptcp: move ooo skbs into msk out of order queue.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This accidentally got wired up to the *get* policy instead
of the *set* policy, causing operations to be rejected. Fix
it by wiring up the correct policy instead.

Fixes: 5028588b ("ethtool: wire up set policies to ops")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ETHTOOL_A_STRSET_COUNTS_ONLY flag attribute was previously
not allowed to be used, but now due to the policy size reduction
we would access the tb[] array out of bounds since we tried to
check for the attribute despite it not being accepted.

Fix both issues by adding it correctly to the appropriate policy.

Fixes: ff419afa ("ethtool: trim policy tables")
Fixes: 71921690 ("ethtool: provide string sets with STRSET_GET request")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull vhost fixes from Michael Tsirkin:
 "Some last minute vhost,vdpa fixes.

  The last two of them haven't been in next but they do seem kind of
  obvious, very small and safe, fix bugs reported in the field, and they
  are both in a new mlx5 vdpa driver, so it's not like we can introduce
  regressions"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vdpa/mlx5: Fix dependency on MLX5_CORE
  vdpa/mlx5: should keep avail_index despite device status
  vhost-vdpa: fix page pinning leakage in error path
  vhost-vdpa: fix vhost_vdpa_map() on error condition
  vhost: Don't call log_access_ok() when using IOTLB
  vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
  vhost: Don't call access_ok() when using IOTLB
  vhost vdpa: fix vhost_vdpa_open error handling

Pull networking fixes from Jakub Kicinski:
 "One more set of fixes from the networking tree:

   - add missing input validation in nl80211_del_key(), preventing
     out-of-bounds access

   - last minute fix / improvement of a MRP netlink (uAPI) interface
     introduced in 5.9 (current) release

   - fix "unresolved symbol" build error under CONFIG_NET w/o
     CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
     BTF.

   - fix 32 bit sub-register bounds tracking in the bpf verifier for OR
     case

   - tcp: fix receive window update in tcp_add_backlog()

   - openvswitch: handle DNAT tuple collision in conntrack-related code

   - r8169: wait for potential PHY reset to finish after applying a FW
     file, avoiding unexpected PHY behaviour and failures later on

   - mscc: fix tail dropping watermarks for Ocelot switches

   - avoid use-after-free in macsec code after a call to the GRO layer

   - avoid use-after-free in sctp error paths

   - add a device id for Cellient MPL200 WWAN card

   - rxrpc fixes:
      - fix the xdr encoding of the contents read from an rxrpc key
      - fix a BUG() for a unsupported encoding type.
      - fix missing _bh lock annotations.
      - fix acceptance handling for an incoming call where the incoming
        call is encrypted.
      - the server token keyring isn't network namespaced - it belongs
        to the server, so there's no need. Namespacing it means that
        request_key() fails to find it.
      - fix a leak of the server keyring"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
  net: usb: qmi_wwan: add Cellient MPL200 card
  macsec: avoid use-after-free in macsec_handle_frame()
  r8169: consider that PHY reset may still be in progress after applying firmware
  openvswitch: handle DNAT tuple collision
  sctp: fix sctp_auth_init_hmacs() error path
  bridge: Netlink interface fix.
  net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
  bpf: Fix scalar32_min_max_or bounds tracking
  tcp: fix receive window update in tcp_add_backlog()
  net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
  mptcp: more DATA FIN fixes
  net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
  net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
  net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
  rxrpc: Fix server keyring leak
  rxrpc: The server keyring isn't network-namespaced
  rxrpc: Fix accept on a connection that need securing
  rxrpc: Fix some missing _bh annotations on locking conn->state_lock
  rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
  rxrpc: Fix rxkad token xdr encoding
  ...

Remove propmt for selecting MLX5_VDPA by the user and modify
MLX5_VDPA_NET to select MLX5_VDPA. Also modify MLX5_VDPA_NET to depend
on mlx5_core.

This fixes an issue where configuration sets 'y' for MLX5_VDPA_NET while
MLX5_CORE is compiled as a module causing link errors.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a86b377 ("vdpa/mlx5: Add VDPA driver for supported mlx5 device")s
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201007064011.GA50074@mtl-vdi-166.wap.labs.mlnxSigned-off-by: Michael S. Tsirkin <mst@redhat.com>

A VM with mlx5 vDPA has below warnings while being reset:

vhost VQ 0 ring restore failed: -1: Resource temporarily unavailable (11)
vhost VQ 1 ring restore failed: -1: Resource temporarily unavailable (11)

We should allow userspace emulating the virtio device be
able to get to vq's avail_index, regardless of vDPA device
status. Save the index that was last seen when virtq was
stopped, so that userspace doesn't complain.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601583511-15138-1-git-send-email-si-wei.liu@oracle.comSigned-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>

Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>