We noticed a 2% webserver throughput regression after upgrading from 5.6. 
This could be tracked down to a shift in the anon/file reclaim balance
(confirmed with swappiness) that resulted in worse reclaim efficiency and
thus more kswapd activity for the same outcome.

The change that exposed the problem is aae466b0 ("mm/swap: implement
workingset detection for anonymous LRU").  By qualifying swapins based on
their refault distance, it lowered the cost of anon reclaim in this
workload, in turn causing (much) more anon scanning than before.  Scanning
the anon list is more expensive due to the higher ratio of mmapped pages
that may rotate during reclaim, and so the result was an increase in %sys
time.

Right now, rotations aren't considered a cost when balancing scan pressure
between LRUs.  We can end up with very few file refaults putting all the
scan pressure on hot anon pages that are rotated en masse, don't get
reclaimed, and never push back on the file LRU again.  We still only
reclaim file cache in that case, but we burn a lot CPU rotating anon
pages.  It's "fair" from an LRU age POV, but doesn't reflect the real cost
it imposes on the system.

Consider rotations as a secondary factor in balancing the LRUs.  This
doesn't attempt to make a precise comparison between IO cost and CPU cost,
it just says: if reloads are about comparable between the lists, or
rotations are overwhelmingly different, adjust for CPU work.

This fixed the regression on our webservers.  It has since been deployed
to the entire Meta fleet and hasn't caused any problems.

Link: https://lkml.kernel.org/r/20221013193113.726425-1-hannes@cmpxchg.orgSigned-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

During discussions of this series [1], it was suggested that hugetlb
handling code in follow_page_mask could be simplified.  At the beginning
of follow_page_mask, there currently is a call to follow_huge_addr which
'may' handle hugetlb pages.  ia64 is the only architecture which provides
a follow_huge_addr routine that does not return error.  Instead, at each
level of the page table a check is made for a hugetlb entry.  If a hugetlb
entry is found, a call to a routine associated with that entry is made.

Currently, there are two checks for hugetlb entries at each page table
level.  The first check is of the form:

        if (p?d_huge())
                page = follow_huge_p?d();

the second check is of the form:

        if (is_hugepd())
                page = follow_huge_pd().

We can replace these checks, as well as the special handling routines such
as follow_huge_p?d() and follow_huge_pd() with a single routine to handle
hugetlb vmas.

A new routine hugetlb_follow_page_mask is called for hugetlb vmas at the
beginning of follow_page_mask.  hugetlb_follow_page_mask will use the
existing routine huge_pte_offset to walk page tables looking for hugetlb
entries.  huge_pte_offset can be overwritten by architectures, and already
handles special cases such as hugepd entries.

[1] https://lore.kernel.org/linux-mm/cover.1661240170.git.baolin.wang@linux.alibaba.com/

[mike.kravetz@oracle.com: remove vma (pmd sharing) per Peter]
  Link: https://lkml.kernel.org/r/20221028181108.119432-1-mike.kravetz@oracle.com
[mike.kravetz@oracle.com: remove left over hugetlb_vma_unlock_read()]
  Link: https://lkml.kernel.org/r/20221030225825.40872-1-mike.kravetz@oracle.com
Link: https://lkml.kernel.org/r/20220919021348.22151-1-mike.kravetz@oracle.comSigned-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Tested-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Pull cxl fixes from Dan Williams:
 "Several fixes for CXL region creation crashes, leaks and failures.

  This is mainly fallout from the original implementation of dynamic CXL
  region creation (instantiate new physical memory pools) that arrived
  in v6.0-rc1.

  Given the theme of "failures in the presence of pass-through decoders"
  this also includes new regression test infrastructure for that case.

  Summary:

   - Fix region creation crash with pass-through decoders

   - Fix region creation crash when no decoder allocation fails

   - Fix region creation crash when scanning regions to enforce the
     increasing physical address order constraint that CXL mandates

   - Fix a memory leak for cxl_pmem_region objects, track 1:N instead of
     1:1 memory-device-to-region associations.

   - Fix a memory leak for cxl_region objects when regions with active
     targets are deleted

   - Fix assignment of NUMA nodes to CXL regions by CFMWS (CXL Window)
     emulated proximity domains.

   - Fix region creation failure for switch attached devices downstream
     of a single-port host-bridge

   - Fix false positive memory leak of cxl_region objects by recycling
     recently used region ids rather than freeing them

   - Add regression test infrastructure for a pass-through decoder
     configuration

   - Fix some mailbox payload handling corner cases"

* tag 'cxl-fixes-for-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/region: Recycle region ids
  cxl/region: Fix 'distance' calculation with passthrough ports
  tools/testing/cxl: Add a single-port host-bridge regression config
  tools/testing/cxl: Fix some error exits
  cxl/pmem: Fix cxl_pmem_region and cxl_memdev leak
  cxl/region: Fix cxl_region leak, cleanup targets at region delete
  cxl/region: Fix region HPA ordering validation
  cxl/pmem: Use size_add() against integer overflow
  cxl/region: Fix decoder allocation crash
  ACPI: NUMA: Add CXL CFMWS 'nodes' to the possible nodes set
  cxl/pmem: Fix failure to account for 8 byte header for writes to the device LSA.
  cxl/region: Fix null pointer dereference due to pass through decoder commit
  cxl/mbox: Add a check on input payload size

Merge tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Fix two regressions:

   - Commit 54cc3dbf ("hwmon: (pmbus) Add regulator supply into
     macro") resulted in regulator undercount when disabling regulators.
     Revert it.

   - The thermal subsystem rework caused the scmi driver to no longer
     register with the thermal subsystem because index values no longer
     match. To fix the problem, the scmi driver now directly registers
     with the thermal subsystem, no longer through the hwmon core"

* tag 'hwmon-for-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  Revert "hwmon: (pmbus) Add regulator supply into macro"
  hwmon: (scmi) Register explicitly with Thermal Framework

Pull perf fixes from Borislav Petkov:

 - Add Cooper Lake's stepping to the PEBS guest/host events isolation
   fixed microcode revisions checking quirk

 - Update Icelake and Sapphire Rapids events constraints

 - Use the standard energy unit for Sapphire Rapids in RAPL

 - Fix the hw_breakpoint test to fail more graciously on !SMP configs

* tag 'perf_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Add Cooper Lake stepping to isolation_ucodes[]
  perf/x86/intel: Fix pebs event constraints for SPR
  perf/x86/intel: Fix pebs event constraints for ICL
  perf/x86/rapl: Use standard Energy Unit for SPR Dram RAPL domain
  perf/hw_breakpoint: test: Skip the test if dependencies unmet

Pull x86 fixes from Borislav Petkov:

 - Add new Intel CPU models

 - Enforce that TDX guests are successfully loaded only on TDX hardware
   where virtualization exception (#VE) delivery on kernel memory is
   disabled because handling those in all possible cases is "essentially
   impossible"

 - Add the proper include to the syscall wrappers so that BTF can see
   the real pt_regs definition and not only the forward declaration

* tag 'x86_urgent_for_v6.1_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add several Intel server CPU model numbers
  x86/tdx: Panic on bad configs that #VE on "private" memory access
  x86/tdx: Prepare for using "INFO" call for a second purpose
  x86/syscall: Include asm/ptrace.h in syscall_wrapper header

Merge tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Use POSIX-compatible grep options

 - Document git-related tips for reproducible builds

 - Fix a typo in the modpost rule

 - Suppress SIGPIPE error message from gcc-ar and llvm-ar

 - Fix segmentation fault in the menuconfig search

* tag 'kbuild-fixes-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: fix segmentation fault in menuconfig search
  kbuild: fix SIGPIPE error message for AR=gcc-ar and AR=llvm-ar
  kbuild: fix typo in modpost
  Documentation: kbuild: Add description of git for reproducible builds
  kbuild: use POSIX-compatible grep option

Pull kvm fixes from Paolo Bonzini:
"ARM:

   - Fix the pKVM stage-1 walker erronously using the stage-2 accessor

   - Correctly convert vcpu->kvm to a hyp pointer when generating an
     exception in a nVHE+MTE configuration

   - Check that KVM_CAP_DIRTY_LOG_* are valid before enabling them

   - Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE

   - Document the boot requirements for FGT when entering the kernel at
     EL1

  x86:

   - Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()

   - Make argument order consistent for kvcalloc()

   - Userspace API fixes for DEBUGCTL and LBRs"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Fix a typo about the usage of kvcalloc()
  KVM: x86: Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()
  KVM: VMX: Ignore guest CPUID for host userspace writes to DEBUGCTL
  KVM: VMX: Fold vmx_supported_debugctl() into vcpu_supported_debugctl()
  KVM: VMX: Advertise PMU LBRs if and only if perf supports LBRs
  arm64: booting: Document our requirements for fine grained traps with SME
  KVM: arm64: Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE
  KVM: Check KVM_CAP_DIRTY_LOG_{RING, RING_ACQ_REL} prior to enabling them
  KVM: arm64: Fix bad dereference on MTE-enabled systems
  KVM: arm64: Use correct accessor to parse stage-1 PTEs

Pull xen fixes from Juergen Gross:
 "One fix for silencing a smatch warning, and a small cleanup patch"

* tag 'for-linus-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  x86/xen: simplify sysenter and syscall setup
  x86/xen: silence smatch warning in pmu_msr_chk_emulated()

Pull ext4 fixes from Ted Ts'o:
 "Fix a number of bugs, including some regressions, the most serious of
  which was one which would cause online resizes to fail with file
  systems with metadata checksums enabled.

  Also fix a warning caused by the newly added fortify string checker,
  plus some bugs that were found using fuzzed file systems"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix fortify warning in fs/ext4/fast_commit.c:1551
  ext4: fix wrong return err in ext4_load_and_init_journal()
  ext4: fix warning in 'ext4_da_release_space'
  ext4: fix BUG_ON() when directory entry has invalid rec_len
  ext4: update the backup superblock's at the end of the online resize

Pull cifs fixes from Steve French:
 "One symlink handling fix and two fixes foir multichannel issues with
  iterating channels, including for oplock breaks when leases are
  disabled"

* tag '6.1-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix use-after-free on the link name
  cifs: avoid unnecessary iteration of tcp sessions
  cifs: always iterate smb sessions using primary channel

Pull `lTracing fixes for 6.1-rc3:

 - Fixed NULL pointer dereference in the ring buffer wait-waiters code
   for machines that have less CPUs than what nr_cpu_ids returns.

   The buffer array is of size nr_cpu_ids, but only the online CPUs get
   initialized.

 - Fixed use after free call in ftrace_shutdown.

 - Fix accounting of if a kprobe is enabled

 - Fix NULL pointer dereference on error path of fprobe rethook_alloc().

 - Fix unregistering of fprobe_kprobe_handler

 - Fix memory leak in kprobe test module

* tag 'trace-v6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing: kprobe: Fix memory leak in test_gen_kprobe/kretprobe_cmd()
  tracing/fprobe: Fix to check whether fprobe is registered correctly
  fprobe: Check rethook_alloc() return in rethook initialization
  kprobe: reverse kp->flags when arm_kprobe failed
  ftrace: Fix use-after-free for dynamic ftrace_ops
  ring-buffer: Check for NULL cpu_buffer in ring_buffer_wake_waiters()

Merge tag 'kvmarm-fixes-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

* Fix the pKVM stage-1 walker erronously using the stage-2 accessor

* Correctly convert vcpu->kvm to a hyp pointer when generating
  an exception in a nVHE+MTE configuration

* Check that KVM_CAP_DIRTY_LOG_* are valid before enabling them

* Fix SMPRI_EL1/TPIDR2_EL0 trapping on VHE

* Document the boot requirements for FGT when entering the kernel
  at EL1

x86:
* Use SRCU to protect zap in __kvm_set_or_clear_apicv_inhibit()

* Make argument order consistent for kvcalloc()

* Userspace API fixes for DEBUGCTL and LBRs

With the new fortify string system, rework the memcpy to avoid this
warning:

memcpy: detected field-spanning write (size 60) of single field "&raw_inode->i_generation" at fs/ext4/fast_commit.c:1551 (size 4)

Cc: stable@kernel.org
Fixes: 54d9469b ("fortify: Add run-time WARN for cross-field memcpy()")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

The return value is wrong in ext4_load_and_init_journal(). The local
variable 'err' need to be initialized before goto out. The original code
in __ext4_fill_super() is fine because it has two return values 'ret'
and 'err' and 'ret' is initialized as -EINVAL. After we factor out
ext4_load_and_init_journal(), this code is broken. So fix it by directly
returning -EINVAL in the error handler path.

Cc: stable@kernel.org
Fixes: 9c1dd22d ("ext4: factor out ext4_load_and_init_journal()")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221025040206.3134773-1-yanaijie@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

Syzkaller report issue as follows:
EXT4-fs (loop0): Free/Dirty block details
EXT4-fs (loop0): free_blocks=0
EXT4-fs (loop0): dirty_blocks=0
EXT4-fs (loop0): Block reservation details
EXT4-fs (loop0): i_reserved_data_blocks=0
EXT4-fs warning (device loop0): ext4_da_release_space:1527: ext4_da_release_space: ino 18, to_free 1 with only 0 reserved data blocks
------------[ cut here ]------------
WARNING: CPU: 0 PID: 92 at fs/ext4/inode.c:1528 ext4_da_release_space+0x25e/0x370 fs/ext4/inode.c:1524
Modules linked in:
CPU: 0 PID: 92 Comm: kworker/u4:4 Not tainted 6.0.0-syzkaller-09423-g493ffd66 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Workqueue: writeback wb_workfn (flush-7:0)
RIP: 0010:ext4_da_release_space+0x25e/0x370 fs/ext4/inode.c:1528
RSP: 0018:ffffc900015f6c90 EFLAGS: 00010296
RAX: 42215896cd52ea00 RBX: 0000000000000000 RCX: 42215896cd52ea00
RDX: 0000000000000000 RSI: 0000000080000001 RDI: 0000000000000000
RBP: 1ffff1100e907d96 R08: ffffffff816aa79d R09: fffff520002bece5
R10: fffff520002bece5 R11: 1ffff920002bece4 R12: ffff888021fd2000
R13: ffff88807483ecb0 R14: 0000000000000001 R15: ffff88807483e740
FS:  0000000000000000(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005555569ba628 CR3: 000000000c88e000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 ext4_es_remove_extent+0x1ab/0x260 fs/ext4/extents_status.c:1461
 mpage_release_unused_pages+0x24d/0xef0 fs/ext4/inode.c:1589
 ext4_writepages+0x12eb/0x3be0 fs/ext4/inode.c:2852
 do_writepages+0x3c3/0x680 mm/page-writeback.c:2469
 __writeback_single_inode+0xd1/0x670 fs/fs-writeback.c:1587
 writeback_sb_inodes+0xb3b/0x18f0 fs/fs-writeback.c:1870
 wb_writeback+0x41f/0x7b0 fs/fs-writeback.c:2044
 wb_do_writeback fs/fs-writeback.c:2187 [inline]
 wb_workfn+0x3cb/0xef0 fs/fs-writeback.c:2227
 process_one_work+0x877/0xdb0 kernel/workqueue.c:2289
 worker_thread+0xb14/0x1330 kernel/workqueue.c:2436
 kthread+0x266/0x300 kernel/kthread.c:376
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
 </TASK>

Above issue may happens as follows:
ext4_da_write_begin
  ext4_create_inline_data
    ext4_clear_inode_flag(inode, EXT4_INODE_EXTENTS);
    ext4_set_inode_flag(inode, EXT4_INODE_INLINE_DATA);
__ext4_ioctl
  ext4_ext_migrate -> will lead to eh->eh_entries not zero, and set extent flag
ext4_da_write_begin
  ext4_da_convert_inline_data_to_extent
    ext4_da_write_inline_data_begin
      ext4_da_map_blocks
        ext4_insert_delayed_block
	  if (!ext4_es_scan_clu(inode, &ext4_es_is_delonly, lblk))
	    if (!ext4_es_scan_clu(inode, &ext4_es_is_mapped, lblk))
	      ext4_clu_mapped(inode, EXT4_B2C(sbi, lblk)); -> will return 1
	       allocated = true;
          ext4_es_insert_delayed_block(inode, lblk, allocated);
ext4_writepages
  mpage_map_and_submit_extent(handle, &mpd, &give_up_on_write); -> return -ENOSPC
  mpage_release_unused_pages(&mpd, give_up_on_write); -> give_up_on_write == 1
    ext4_es_remove_extent
      ext4_da_release_space(inode, reserved);
        if (unlikely(to_free > ei->i_reserved_data_blocks))
	  -> to_free == 1  but ei->i_reserved_data_blocks == 0
	  -> then trigger warning as above

To solve above issue, forbid inode do migrate which has inline data.

Cc: stable@kernel.org
Reported-by: syzbot+c740bb18df70ad00952e@syzkaller.appspotmail.com
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221018022701.683489-1-yebin10@huawei.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>

The rec_len field in the directory entry has to be a multiple of 4.  A
corrupted filesystem image can be used to hit a BUG() in
ext4_rec_len_to_disk(), called from make_indexed_dir().

 ------------[ cut here ]------------
 kernel BUG at fs/ext4/ext4.h:2413!
 ...
 RIP: 0010:make_indexed_dir+0x53f/0x5f0
 ...
 Call Trace:
  <TASK>
  ? add_dirent_to_buf+0x1b2/0x200
  ext4_add_entry+0x36e/0x480
  ext4_add_nondir+0x2b/0xc0
  ext4_create+0x163/0x200
  path_openat+0x635/0xe90
  do_filp_open+0xb4/0x160
  ? __create_object.isra.0+0x1de/0x3b0
  ? _raw_spin_unlock+0x12/0x30
  do_sys_openat2+0x91/0x150
  __x64_sys_open+0x6c/0xa0
  do_syscall_64+0x3c/0x80
  entry_SYSCALL_64_after_hwframe+0x46/0xb0

The fix simply adds a call to ext4_check_dir_entry() to validate the
directory entry, returning -EFSCORRUPTED if the entry is invalid.

CC: stable@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216540Signed-off-by: Luís Henriques <lhenriques@suse.de>
Link: https://lore.kernel.org/r/20221012131330.32456-1-lhenriques@suse.deSigned-off-by: Theodore Ts'o <tytso@mit.edu>

Pull ACPI fix from Rafael Wysocki:
 "Add StorageD3Enable quirk for Dell Inspiron 16 5625 (Mario
  Limonciello)"

* tag 'acpi-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: x86: Add another system to quirk list for forcing StorageD3Enable

* acpi-x86:
  ACPI: x86: Add another system to quirk list for forcing StorageD3Enable

Pull block fixes from Jens Axboe:

 - Fixes for the ublk driver (Ming)

 - Fixes for error handling memory leaks (Chen Jun, Chen Zhongjin)

 - Explicitly clear the last request in a chain when the plug is
   flushed, as it may have already been issued (Al)

* tag 'block-6.1-2022-11-05' of git://git.kernel.dk/linux:
  block: blk_add_rq_to_plug(): clear stale 'last' after flush
  blk-mq: Fix kmemleak in blk_mq_init_allocated_queue
  block: Fix possible memory leak for rq_wb on add_disk failure
  ublk_drv: add ublk_queue_cmd() for cleanup
  ublk_drv: avoid to touch io_uring cmd in blk_mq io path
  ublk_drv: comment on ublk_driver entry of Kconfig
  ublk_drv: return flag of UBLK_F_URING_CMD_COMP_IN_TASK in case of module

xfstests generic/011 reported use-after-free bug as follows:

  BUG: KASAN: use-after-free in __d_alloc+0x269/0x859
  Read of size 15 at addr ffff8880078933a0 by task dirstress/952

  CPU: 1 PID: 952 Comm: dirstress Not tainted 6.1.0-rc3+ #77
  Call Trace:
   __dump_stack+0x23/0x29
   dump_stack_lvl+0x51/0x73
   print_address_description+0x67/0x27f
   print_report+0x3e/0x5c
   kasan_report+0x7b/0xa8
   kasan_check_range+0x1b2/0x1c1
   memcpy+0x22/0x5d
   __d_alloc+0x269/0x859
   d_alloc+0x45/0x20c
   d_alloc_parallel+0xb2/0x8b2
   lookup_open+0x3b8/0x9f9
   open_last_lookups+0x63d/0xc26
   path_openat+0x11a/0x261
   do_filp_open+0xcc/0x168
   do_sys_openat2+0x13b/0x3f7
   do_sys_open+0x10f/0x146
   __se_sys_creat+0x27/0x2e
   __x64_sys_creat+0x55/0x6a
   do_syscall_64+0x40/0x96
   entry_SYSCALL_64_after_hwframe+0x63/0xcd

  Allocated by task 952:
   kasan_save_stack+0x1f/0x42
   kasan_set_track+0x21/0x2a
   kasan_save_alloc_info+0x17/0x1d
   __kasan_kmalloc+0x7e/0x87
   __kmalloc_node_track_caller+0x59/0x155
   kstrndup+0x60/0xe6
   parse_mf_symlink+0x215/0x30b
   check_mf_symlink+0x260/0x36a
   cifs_get_inode_info+0x14e1/0x1690
   cifs_revalidate_dentry_attr+0x70d/0x964
   cifs_revalidate_dentry+0x36/0x62
   cifs_d_revalidate+0x162/0x446
   lookup_open+0x36f/0x9f9
   open_last_lookups+0x63d/0xc26
   path_openat+0x11a/0x261
   do_filp_open+0xcc/0x168
   do_sys_openat2+0x13b/0x3f7
   do_sys_open+0x10f/0x146
   __se_sys_creat+0x27/0x2e
   __x64_sys_creat+0x55/0x6a
   do_syscall_64+0x40/0x96
   entry_SYSCALL_64_after_hwframe+0x63/0xcd

  Freed by task 950:
   kasan_save_stack+0x1f/0x42
   kasan_set_track+0x21/0x2a
   kasan_save_free_info+0x1c/0x34
   ____kasan_slab_free+0x1c1/0x1d5
   __kasan_slab_free+0xe/0x13
   __kmem_cache_free+0x29a/0x387
   kfree+0xd3/0x10e
   cifs_fattr_to_inode+0xb6a/0xc8c
   cifs_get_inode_info+0x3cb/0x1690
   cifs_revalidate_dentry_attr+0x70d/0x964
   cifs_revalidate_dentry+0x36/0x62
   cifs_d_revalidate+0x162/0x446
   lookup_open+0x36f/0x9f9
   open_last_lookups+0x63d/0xc26
   path_openat+0x11a/0x261
   do_filp_open+0xcc/0x168
   do_sys_openat2+0x13b/0x3f7
   do_sys_open+0x10f/0x146
   __se_sys_creat+0x27/0x2e
   __x64_sys_creat+0x55/0x6a
   do_syscall_64+0x40/0x96
   entry_SYSCALL_64_after_hwframe+0x63/0xcd

When opened a symlink, link name is from 'inode->i_link', but it may be
reset to a new value when revalidate the dentry. If some processes get the
link name on the race scenario, then UAF will happen on link name.

Fix this by implementing 'get_link' interface to duplicate the link name.

Fixes: 76894f3e ("cifs: improve symlink handling for smb2+")
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>

In a few places, we do unnecessary iterations of
tcp sessions, even when the server struct is provided.

The change avoids it and uses the server struct provided.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>

smb sessions and tcons currently hang off primary channel only.
Secondary channels have the lists as empty. Whenever there's a
need to iterate sessions or tcons, we should use the list in the
corresponding primary channel.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>

Pull arm64 fixes from Catalin Marinas:

 - Avoid kprobe recursion when cortex_a76_erratum_1463225_debug_handler()
   is not inlined (change to __always_inline).

 - Fix the visibility of compat hwcaps, broken by recent changes to
   consolidate the visibility of hwcaps and the user-space view of the
   ID registers.

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: cpufeature: Fix the visibility of compat hwcaps
  arm64: entry: avoid kprobe recursion

Pull i2c fixes from Wolfram Sang:
 "A documentation fix and driver fixes for piix4, tegra, and i801"

* tag 'i2c-for-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Documentation: devres: add missing I2C helper
  i2c: i801: add lis3lv02d's I2C address for Vostro 5568
  i2c: tegra: Allocate DMA memory for DMA engine
  i2c: piix4: Fix adapter not be removed in piix4_remove()

This reverts commit 54cc3dbf.

Zev Weiss reports that the reverted patch may cause a regulator
undercount. Here is his report:

... having regulator-dummy set as a supply on my PMBus regulators
(instead of having them as their own top-level regulators without
an upstream supply) leads to enable-count underflow errors when
disabling them:

    # echo 0 > /sys/bus/platform/devices/efuse01/state
    [  906.094477] regulator-dummy: Underflow of regulator enable count
    [  906.100563] Failed to disable vout: -EINVAL
    [  136.992676] reg-userspace-consumer efuse01: Failed to configure state: -22

Zev reports that reverting the patch fixes the problem. So let's do that
for now.

Fixes: 54cc3dbf ("hwmon: (pmbus) Add regulator supply into macro")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Reported-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Available sensors are enumerated and reported by the SCMI platform server
using a 16bit identification number; not all such sensors are of a type
supported by hwmon subsystem and, among the supported ones, only a subset
could be temperature sensors that have to be registered with the Thermal
Framework.
Potential clashes between hwmon channels indexes and the underlying real
sensors IDs do not play well with the hwmon<-->thermal bridge automatic
registration routines and could need a sensible number of fake dummy
sensors to be made up in order to keep indexes and IDs in sync.

Avoid to use the hwmon<-->thermal bridge dropping the HWMON_C_REGISTER_TZ
attribute and instead explicit register temperature sensors directly with
the Thermal Framework.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20221031114018.59048-1-cristian.marussi@arm.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

At region creation time the next region-id is atomically cached so that
there is predictability of region device names. If that region is
destroyed and then a new one is created the region id increments. That
ends up looking like a memory leak, or is otherwise surprising that
identifiers roll forward even after destroying all previously created
regions.

Try to reuse rather than free old region ids at region release time.

While this fixes a cosmetic issue, the needlessly advancing memory
region-id gives the appearance of a memory leak, hence the "Fixes" tag,
but no "Cc: stable" tag.

Cc: Ben Widawsky <bwidawsk@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 779dd20c ("cxl/region: Add region creation support")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752186062.947915.13200195701224993317.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

When programming port decode targets, the algorithm wants to ensure that
two devices are compatible to be programmed as peers beneath a given
port. A compatible peer is a target that shares the same dport, and
where that target's interleave position also routes it to the same
dport. Compatibility is determined by the device's interleave position
being >= to distance. For example, if a given dport can only map every
Nth position then positions less than N away from the last target
programmed are incompatible.

The @distance for the host-bridge's cxl_port in a simple dual-ported
host-bridge configuration with 2 direct-attached devices is 1, i.e. An
x2 region divided by 2 dports to reach 2 region targets.

An x4 region under an x2 host-bridge would need 2 intervening switches
where the @distance at the host bridge level is 2 (x4 region divided by
2 switches to reach 4 devices).

However, the distance between peers underneath a single ported
host-bridge is always zero because there is no limit to the number of
devices that can be mapped. In other words, there are no decoders to
program in a passthrough, all descendants are mapped and distance only
starts matters for the intervening descendant ports of the passthrough
port.

Add tracking for the number of dports mapped to a port, and use that to
detect the passthrough case for calculating @distance.

Cc: <stable@vger.kernel.org>
Reported-by: Bobo WL <lmw.bobo@gmail.com>
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: http://lore.kernel.org/r/20221010172057.00001559@huawei.com
Fixes: 27b3f8d1 ("cxl/region: Program target lists")
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752185440.947915.6617495912508299445.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Jonathan reports that region creation fails when a single-port
host-bridge connects to a multi-port switch. Mock up that configuration
so a fix can be tested and regression tested going forward.
Reported-by: Bobo WL <lmw.bobo@gmail.com>
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: http://lore.kernel.org/r/20221010172057.00001559@huawei.comReviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752184838.947915.2167957540894293891.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Fix a few typos where 'goto err_port' was used rather than the object
specific cleanup.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752184255.947915.16163477849330181425.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

When a cxl_nvdimm object goes through a ->remove() event (device
physically removed, nvdimm-bridge disabled, or nvdimm device disabled),
then any associated regions must also be disabled. As highlighted by the
cxl-create-region.sh test [1], a single device may host multiple
regions, but the driver was only tracking one region at a time. This
leads to a situation where only the last enabled region per nvdimm
device is cleaned up properly. Other regions are leaked, and this also
causes cxl_memdev reference leaks.

Fix the tracking by allowing cxl_nvdimm objects to track multiple region
associations.

Cc: <stable@vger.kernel.org>
Link: https://github.com/pmem/ndctl/blob/main/test/cxl-create-region.sh [1]
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 04ad63f0 ("cxl/region: Introduce cxl_pmem_region objects")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752183647.947915.2045230911503793901.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

When a region is deleted any targets that have been previously assigned
to that region hold references to it. Trigger those references to
drop by detaching all targets at unregister_region() time.

Otherwise that region object will leak as userspace has lost the ability
to detach targets once region sysfs is torn down.

Cc: <stable@vger.kernel.org>
Fixes: b9686e8c ("cxl/region: Enable the assignment of endpoint decoders to regions")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752183055.947915.17681995648556534844.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Some regions may not have any address space allocated. Skip them when
validating HPA order otherwise a crash like the following may result:

 devm_cxl_add_region: cxl_acpi cxl_acpi.0: decoder3.4: created region9
 BUG: kernel NULL pointer dereference, address: 0000000000000000
 [..]
 RIP: 0010:store_targetN+0x655/0x1740 [cxl_core]
 [..]
 Call Trace:
  <TASK>
  kernfs_fop_write_iter+0x144/0x200
  vfs_write+0x24a/0x4d0
  ksys_write+0x69/0xf0
  do_syscall_64+0x3a/0x90

store_targetN+0x655/0x1740:
alloc_region_ref at drivers/cxl/core/region.c:676
(inlined by) cxl_port_attach_region at drivers/cxl/core/region.c:850
(inlined by) cxl_region_attach at drivers/cxl/core/region.c:1290
(inlined by) attach_target at drivers/cxl/core/region.c:1410
(inlined by) store_targetN at drivers/cxl/core/region.c:1453

Cc: <stable@vger.kernel.org>
Fixes: 384e624b ("cxl/region: Attach endpoint decoders")
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166752182461.947915.497032805239915067.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Pull xfs fixes from Darrick Wong:
 "Dave and I had thought that this would be a very quiet cycle, but we
  thought wrong.

  At first there were the usual trickle of minor bugfixes, but then
  Zorro pulled -rc1 and noticed complaints about the stronger memcpy
  checks w.r.t. flex arrays.

  Analyzing how to fix that revealed a bunch of validation gaps in
  validating ondisk log items during recovery, and then a customer hit
  an infinite loop in the refcounting code on a corrupt filesystem.

  So. This largeish batch of fixes addresses all those problems, I hope.

  Summary:

   - Fix a UAF bug during log recovery

   - Fix memory leaks when mount fails

   - Detect corrupt bestfree information in a directory block

   - Fix incorrect return value type for the dax page fault handlers

   - Fix fortify complaints about memcpy of xfs log item objects

   - Strengthen inadequate validation of recovered log items

   - Fix incorrectly declared flex array in EFI log item structs

   - Log corrupt log items for debugging purposes

   - Fix infinite loop problems in the refcount code if the refcount
     btree node block keys are corrupt

   - Fix infinite loop problems in the refcount code if the refcount
     btree records suffer MSB bitflips

   - Add more sanity checking to continued defer ops to prevent
     overflows from one AG to the next or off EOFS"

* tag 'xfs-6.1-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (28 commits)
  xfs: rename XFS_REFC_COW_START to _COWFLAG
  xfs: fix uninitialized list head in struct xfs_refcount_recovery
  xfs: fix agblocks check in the cow leftover recovery function
  xfs: check record domain when accessing refcount records
  xfs: remove XFS_FIND_RCEXT_SHARED and _COW
  xfs: refactor domain and refcount checking
  xfs: report refcount domain in tracepoints
  xfs: track cow/shared record domains explicitly in xfs_refcount_irec
  xfs: refactor refcount record usage in xchk_refcountbt_rec
  xfs: dump corrupt recovered log intent items to dmesg consistently
  xfs: move _irec structs to xfs_types.h
  xfs: actually abort log recovery on corrupt intent-done log items
  xfs: check deferred refcount op continuation parameters
  xfs: refactor all the EFI/EFD log item sizeof logic
  xfs: create a predicate to verify per-AG extents
  xfs: fix memcpy fortify errors in EFI log format copying
  xfs: make sure aglen never goes negative in xfs_refcount_adjust_extents
  xfs: fix memcpy fortify errors in RUI log format copying
  xfs: fix memcpy fortify errors in CUI log format copying
  xfs: fix memcpy fortify errors in BUI log format copying
  ...

Pull landlock fix from Mickaël Salaün:
 "Fix the test build for some distros"

* tag 'landlock-6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
  selftests/landlock: Build without static libraries

Pull hardening fix from Kees Cook:

 - Correctly report struct member size on memcpy overflow (Kees Cook)

* tag 'hardening-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  fortify: Capture __bos() results in const temp vars

Pull EFI fixes from Ard Biesheuvel:

 - A pair of tweaks to the EFI random seed code so that externally
   provided version of this config table are handled more robustly

 - Another fix for the v6.0 EFI variable refactor that turned out to
   break Apple machines which don't provide QueryVariableInfo()

 - Add some guard rails to the EFI runtime service call wrapper so we
   can recover from synchronous exceptions caused by firmware

* tag 'efi-fixes-for-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  arm64: efi: Recover from synchronous exceptions occurring in firmware
  efi: efivars: Fix variable writes with unsupported query_variable_store()
  efi: random: Use 'ACPI reclaim' memory for random seed
  efi: random: reduce seed size to 32 bytes
  efi/tpm: Pass correct address to memblock_reserve