In a very similar spirit to commit c470bdc1 ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()

  wlan0: invalid CW_min/CW_max: 0/0

and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.

Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().

Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190726224758.210953-1-briannorris@chromium.orgSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Commit 33d915d9 ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.

General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.

Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.

Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9 ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.orgSigned-off-by: Johannes Berg <johannes.berg@intel.com>

We need the same checks introduced by commit cb9f1b78
("ip: validate header length on virtual device xmit") for
ipip tunnel.

Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_flowlabel and ipv6_flowlabel_mgr are missing from
gitignore.  Quentin points out that the original
commit 3fb321fd ("selftests/net: ipv6 flowlabel")
did add ignore entries, they are just missing the "ipv6_"
prefix.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3968d389 ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.

Fixes: 3968d389 ("bnx2x: Fix Multi-Cos.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_kzalloc may fail and return NULL. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_kzalloc may fail and return null. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- v1 -> v2: Move skb_set_owner_w to __tun_build_skb to reduce patch size

Small packets going out of a tap device go through an optimized code
path that uses build_skb() rather than sock_alloc_send_pskb(). The
latter calls skb_set_owner_w(), but the small packet code path does not.

The net effect is that small packets are not owned by the userland
application's socket (e.g. QEMU), while large packets are.
This can be seen with a TCP session, where packets are not owned when
the window size is small enough (around PAGE_SIZE), while they are once
the window grows (note that this requires the host to support virtio
tso for the guest to offload segmentation).
All this leads to inconsistent behaviour in the kernel, especially on
netfilter modules that uses sk->socket (e.g. xt_owner).

Fixes: 66ccbc9c ("tap: use build_skb() for small packet")
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
DIM fixes for 5.3

Those two fixes for recently merged DIM patches, both exposed through
RDMa DIM usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DIM causes to the following warnings during kernel compilation
which indicates that tx_profile and rx_profile are supposed to
be declared in *.c and not in *.h files.

In file included from ./include/rdma/ib_verbs.h:64,
                 from ./include/linux/mlx5/device.h:37,
                 from ./include/linux/mlx5/driver.h:51,
                 from ./include/linux/mlx5/vport.h:36,
                 from drivers/infiniband/hw/mlx5/ib_virt.c:34:
./include/linux/dim.h:326:1: warning: _tx_profile_ defined but not used [-Wunused-const-variable=]
  326 | tx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
      | ^~~~~~~~~~
./include/linux/dim.h:320:1: warning: _rx_profile_ defined but not used [-Wunused-const-variable=]
  320 | rx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
      | ^~~~~~~~~~

Fixes: 4f75da36 ("linux/dim: Move implementation to .c files")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.

[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'

Fixes: 398c2b05 ("linux/dim: Add completions count to dim_sample")
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

act_ife at least requires TCA_IFE_PARMS, so we have to bail out
when there is no attribute passed in.

Reported-by: syzbot+fbb5b288c9cb6a2eeac4@syzkaller.appspotmail.com
Fixes: ef6980b6 ("introduce IFE action")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_efree() releases the sock refcnt, if we don't hold this refcnt
when setting skb->destructor to it, the refcnt would not be balanced.
This leads to several bug reports from syzbot.

I have checked other users of sock_efree(), all of them hold the
sock refcnt.

Fixes: c8c8218e ("netrom: fix a memory leak in nr_rx_frame()")
Reported-and-tested-by: <syzbot+622bdabb128acc33427d@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+6eaef7158b19e3fec3a0@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+9399c158fcc09b21d0d2@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+a34e5f3d0300163f0c87@syzkaller.appspotmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some functions in the datapath code are factored out so that each
one has a stack frame smaller than 1024 bytes with gcc. However,
when compiling with clang, the functions are inlined more aggressively
and combined again so we get

net/openvswitch/datapath.c:1124:12: error: stack frame size of 1528 bytes in function 'ovs_flow_cmd_set' [-Werror,-Wframe-larger-than=]

Marking both get_flow_actions() and ovs_nla_init_match_and_action()
as 'noinline_for_stack' gives us the same behavior that we see with
gcc, and no warning. Note that this does not mean we actually use
less stack, as the functions call each other, and we still get
three copies of the large 'struct sw_flow_key' type on the stack.

The comment tells us that this was previously considered safe,
presumably since the netlink parsing functions are called with
a known backchain that does not also use a lot of stack space.

Fixes: 9cc9a5cb ("datapath: Avoid using stack larger than 1024.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've been spending quite a bit of time fixing and
preventing bit rot in the core TLS code. TLS seems
to only be growing in importance, I'd like to help
ensuring the quality of our implementation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory allocated for the stats array may contain arbitrary data.

Fixes: e4f9ba64 ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.

Since commit ce0aa27f ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:

  % ip link set up dev eth0
  ------------[ cut here ]------------
  called from state UP
  WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
  Modules linked in:
  CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
  NIP:  c0227bf0 LR: c0227bf0 CTR: c004d224
  REGS: df547720 TRAP: 0700   Not tainted  (5.2.0+)
  MSR:  00029000 <CE,EE,ME>  CR: 24002822  XER: 00000000

  GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
  GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
  GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
  GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
  NIP [c0227bf0] phy_start+0x74/0xc0
  LR [c0227bf0] phy_start+0x74/0xc0
  Call Trace:
  [df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
  [df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
  [df547828] [c023cf08] gfar_enet_open+0x364/0x374
  [df547898] [c029d870] __dev_open+0xe4/0x140
  [df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
  [df5478f8] [c029dc28] dev_change_flags+0x20/0x54
  [df547918] [c02ae304] do_setlink+0x310/0x818
  [df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df547c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
  --- interrupt: c01 at 0xfd4e030
      LR = 0xfd4e010
  Instruction dump:
  813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
  3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
  ---[ end trace d4c095aeaf6ea998 ]---

and

  % ip link set down dev eth0
  ------------[ cut here ]------------
  called from state HALTED
  WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88

  <...>

  Call Trace:
  [df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
  [df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
  [df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
  [df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
  [df581858] [c0225608] phylink_stop+0x7c/0xe4
  [df581868] [c023c57c] stop_gfar+0x7c/0x94
  [df581888] [c023c5b8] gfar_close+0x24/0x94
  [df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
  [df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
  [df5818f8] [c029dc28] dev_change_flags+0x20/0x54
  [df581918] [c02ae304] do_setlink+0x310/0x818
  [df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df581c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df581f38] [c000d1d8] ret_from_syscall+0x0/0x38

  <...>

  ---[ end trace d4c095aeaf6ea999 ]---

SFP modules with the 1000Base-X interface are not affected.

Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.

Fixes: 21796261 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.3-20190724' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-07-24

this is a pull reqeust of 7 patches for net/master.

The first patch is by Rasmus Villemoes add a missing netif_carrier_off() to
register_candev() so that generic netdev trigger based LEDs are initially off.

Nikita Yushchenko's patch for the rcar_canfd driver fixes a possible IRQ storm
on high load.

The patch by Weitao Hou for the mcp251x driver add missing error checking to
the work queue allocation.

Both Wen Yang's and Joakim Zhang's patch for the flexcan driver fix a problem
with the stop-mode.

Stephane Grosjean contributes a patch for the peak_usb driver to fix a
potential double kfree_skb().

The last patch is by YueHaibing and fixes the error path in can-gw's
cgw_module_init() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull()
which may change skb->data, so we need to re-load ipv6h at
the right place.

Fixes: 898b2979 ("ip6_gre: Refactor ip6gre xmit codes")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanup testing for error condition.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add error path for cgw_module_init to avoid possible crash if
some error occurs.

Fixes: c1aabdf3 ("can-gw: add netlink based CAN routing")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.

Fixes: bb478555 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

add error check when workqueue alloc failed, and remove redundant code
to make it clear.

Fixes: e0000163 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
  error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
  napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
  thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
  in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
  calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
  NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
  interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
  and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
  returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
  without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
  and again is misprocessed in the same way.

This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.

Fixes: dd3bd23e ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.

Make sure the LED always reflects the state of the CAN device.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Replace the custom implementation with fwnode_get_mac_address,
which works on both DT and ACPI platforms.

While here, replace memcpy() by ether_addr_copy().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem.  Disabling MSI works around it, so
let's add it to the blacklist.

Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496Reported-and-tested-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: forwarding: GRE multipath fixes

Patch #1 ensures IPv4 forwarding is enabled during the test.

Patch #2 fixes the flower filters used to measure the distribution of
the traffic between the two nexthops, so that the test will pass
regardless if traffic is offloaded or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The TC filters used in the test do not work with veth devices because the
outer Ethertype is 802.1Q and not IPv4. The test passes with mlxsw
netdevs since the hardware always looks at "The first Ethertype that
does not point to either: VLAN, CNTAG or configurable Ethertype".

Fix this by matching on the VLAN ID instead, but on the ingress side.
The reason why this is not performed at egress is explained in the
commit cited below.

Fixes: 541ad323 ("selftests: forwarding: gre_multipath: Update next-hop statistics match criteria")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test did not enable IPv4 forwarding during its setup phase, which
causes the test to fail on machines where IPv4 forwarding is disabled.

Fixes: 54818c4c ("selftests: forwarding: Test multipath tunneling")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit f4e5f775.

Andrew Lunn says this should be handled another way.
Signed-off-by: David S. Miller <davem@davemloft.net>

Some glue logic drivers support 1G without having GMAC/GMAC4/XGMAC.

Let's allow this speed by default.
Reported-by: Ondrej Jirman <megi@xff.cz>
Tested-by: Ondrej Jirman <megi@xff.cz>
Fixes: 5b0d7d7d ("net: stmmac: Add the missing speeds that XGMAC supports")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: Two fixes

Two fixes targeting -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need the memory to be zeroed upon allocation so use kcalloc()
instead.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX Descriptors are being cleaned after setting the buffers which may
lead to buffer addresses being wiped out.

Fix this by clearing earlier the RX Descriptors.

Fixes: 2af6106a ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>