- 24 Aug, 2015 3 commits
-
-
ludovic.desroches@atmel.com authored
Add an entry for Atmel SDMMC device. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
ludovic.desroches@atmel.com authored
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci compliant controller. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
ludovic.desroches@atmel.com authored
In programmable mode, if the clock frequency is too high, the divider can be too small to meet the clock frequency requirement especially to init the SD card. In this case, switch to the divided clock mode. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
- 17 Aug, 2015 23 commits
-
-
Addy Ke authored
This patch add a new quirk to add a s/w timer to notify the driver to terminate current transfer and report a data timeout to the core, if DTO interrupt does NOT come within the given time. dw_mmc call mmc_request_done func to finish transfer depends on DTO interrupt. If DTO interrupt does not come in sending data state, the current transfer will be blocked. We got the reply from synopsys: There are two counters but both use the same value of [31:8] bits. Data timeout counter doesn't wait for stop clock and you should get DRTO even when the clock is not stopped. Host Starvation timeout counter is triggered with stop clock condition. This means that host should get DRTO and DTO interrupt. But this case really exists, when driver reads tuning data from card on RK3288-pink2 board. I measured waveforms by oscilloscope and found that card clock was always on and data lines were always holded high level in sending data state. There are two possibility that data over interrupt doesn't come in reading data state on RK3X SoCs: - get command done interrupt, but doesn't get any data-related interrupt. - get data error interrupt, but doesn't get data over interrupt. Signed-off-by: Addy Ke <addy.ke@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Jaehoon Chung authored
supports-highspeed was deprecated. If someone use it, we need to notice information for it. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Jaehoon Chung authored
"blk_setting" doesn't use anywhere. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Jaehoon Chung authored
When num-slots is lower than 1, it's right that should be returned -ENODEV. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Heiko Stuebner authored
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused by things like wrong dma settings in the system. Till now the code dw_mci_init_slot() always assumed that dma is available when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var set during dma init. So when now the dma init failed for whatever reason, the transfer sizes would still be set for dma transfers, especially including the maximum block-count calculated from host->ring_size and resulting in a [ 4.991109] ------------[ cut here ]------------ [ 4.991111] kernel BUG at drivers/mmc/core/core.c:256! [ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM because host->ring_size is 0 in this case and the slot init code uses the wrong code to calculate the values. Fix this by selecting the correct calculations using the host->use_dma variable instead of the CONFIG_MMC_DW_IDMAC config option. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Shawn Lin authored
This patch fixes the following issues reported by checkpatch.pl: - use -EINVAL instead of -ENOSYS, to fix warning message: "ENOSYS means 'invalid syscall nr' and nothing else" - split lines whose length is greater than 80 characters - avoid quoted string split across lines - use min_t instead of min, to fix warning message: "min() should probably be min_t(int, cnt, host->part_buf_count)" - fix missing a blank line after declarations Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Alexey Brodkin authored
As per DW MobileStorage databook "each descriptor can transfer up to 4kB of data in chained mode", moreover buffer size that is put in "des1" is limited to 13 bits, i.e. for example on attempt to IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written will be 0. On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in SG-list of 8kB size and that leads to unpredictable behavior of the SD/MMC controller. In particular on write to FAT partition of SD-card the controller will stuck in the middle of DMA transaction. Solution to the problem is simple - we need to pass large (> 4kB) data buffers to the controller via multiple descriptors. And that's what that change does. What's interesting I did try original driver on same platform but configured with 4kB PAGE_SIZE and may confirm that data blocks passed in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody ever faced a problem I did. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Seungwon Jeon <tgih.jun@samsung.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: arc-linux-dev@synopsys.com Cc: linux-kernel@vger.kernel.org Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
-
Yangbo Lu authored
Some Sandisk cards(such as "SDMB-32" and "SDM032" cards) can't support CMD23, and would generate CMD timeout. So add FIX-UP for these two types Sandisk cards. Error log: mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900 mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900 mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900 end_request: I/O error, dev mmcblk0, sector 0 Buffer I/O error on device mmcblk0, logical block 0 mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900 Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Yangbo Lu authored
eSDHC supports high speed mode, but has no enabling bit for it. Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Yangbo Lu authored
For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt in the process of resume without inserting SD adapter because of some unknown issue. But the driver doesn't assign sdio_irq_thread pointer. This will block the resume of kernel. This patch is used to avoid using NULL sdio_irq_thread pointer. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Andreas Fenkart authored
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Andreas Fenkart authored
If no pdata.set_power was set by the platform code, the driver was updating pdata with its own fallback function. This is a no-no since pdata shall be read-only. This patch pushes the check 'pdata->set_power != NULL' down into the fallback functions. If pdata.set_power is really set, it calls them and exits, otherwise the fallback code is used. Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Andreas Fenkart authored
Before 5b83b223 the driver was hard coding the wakeup irq to be active low. The generic pm wakeirq does not override the active high/low parameter, hence it must be specified correctly in the device tree. Mind that SDIO IRQ is active low as defined in the SDIO specification Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ivan T. Ivanov authored
Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which properly check for BROKEN_CARD_DETECTION quirk. Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ivan T. Ivanov authored
There is no reason to use polling for card detection state change when drivers are using dedicated GPIO for this. Don't poll in this case. Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ivan T. Ivanov authored
Controller could have BROKEN_CARD_DETECTION quirk set, but drivers could use GPIO to detect card present state. Let, when defined, GPIO take precedence, so drivers could properly detect card state and not use polling. Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Ivan T. Ivanov authored
Ensure SDCC is working with maximum clock otherwise card detection could be extremely slow, up to 7 seconds. Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org> Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org> Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Andy Shevchenko authored
It's excessive to use prefix for the parameters when you do modprobe mmc-block mmcblk.perdev_minors=16 Make this available only for built-in case. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Fabian Frederick authored
See Documentation/DMA-API.txt - Part Id Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Suneel Garapati authored
adding SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,SDHCI_QUIRK2_PRESET_VALUE_BROKEN flags for arasan sdhc. Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Suneel Garapati authored
adds quirk for controllers whose clock divider zero is broken, sdhci_set_clock function will incorporate this modification. Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Daniel Mack authored
Switch over pxamci to dmaengine. This prepares the devicetree full support of pxamci. This was successfully tested on a PXA3xx board, as well as PXA27x. Signed-off-by: Daniel Mack <zonque@gmail.com> [adapted to pxa-dma] Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
David Jander authored
In the (not so unlikely) case that the mmc controller timeout budget is enough for exactly one erase-group, the simplification of allowing one sector has an enormous performance penalty. We optimize this special case by introducing a flag that prohibits erase-group boundary crossing, so that we can allow trimming more than one sector at a time. Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
- 16 Aug, 2015 8 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A smallish batch of fixes, a little more than expected this late, but all fixes are contained to their platforms and seem reasonably low risk: - a somewhat large SMP fix for ux500 that still seemed warranted to include here - OMAP DT fixes for pbias regulator specification that broke due to some DT reshuffling - PCIe IRQ routing bugfix for i.MX - networking fixes for keystone - runtime PM for OMAP GPMC - a couple of error path bug fixes for exynos" * tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file ARM: dts: keystone: fix the clock node for mdio memory: omap-gpmc: Don't try to save uninitialized GPMC context ARM: imx6: correct i.MX6 PCIe interrupt routing ARM: ux500: add an SMP enablement type and move cpu nodes ARM: dts: dra7: Fix broken pbias device creation ARM: dts: OMAP5: Fix broken pbias device creation ARM: dts: OMAP4: Fix broken pbias device creation ARM: dts: omap243x: Fix broken pbias device creation ARM: EXYNOS: fix double of_node_put() on error path ARM: EXYNOS: Fix potentian kfree() of ro memory
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS bugfix from Ralf Baechle: "Only a single MIPS fix - the math when invoking syscall_trace_enter was wrong" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: Fix seccomp syscall argument for MIPS64
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Merge x86 fixes from Ingo Molnar: "Two followup fixes related to the previous LDT fix" Also applied a further FPU emulation fix from Andy Lutomirski to the branch before actually merging it. * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip x86/ldt: Further fix FPU emulation x86/ldt: Correct FPU emulation access to LDT x86/ldt: Correct LDT access in single stepping logic
-
Andy Lutomirski authored
The previous fix confused a selector with a segment prefix. Fix it. Compile-tested only. Cc: stable@vger.kernel.org Cc: Juergen Gross <jgross@suse.com> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Fixes: 4809146b ("x86/ldt: Correct FPU emulation access to LDT") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Jann Horn authored
fuse_dev_ioctl() performed fuse_get_dev() on a user-supplied fd, leading to a type confusion issue. Fix it by checking file->f_op. Signed-off-by: Jann Horn <jann@thejh.net> Acked-by: Miklos Szeredi <miklos@szeredi.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Olof Johansson authored
Merge tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+ These are necessary to get the NIC card working on all Keystone EVMs. Couple of boards are broken without these two fixes. * tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file ARM: dts: keystone: fix the clock node for mdio Signed-off-by: Olof Johansson <olof@lixom.net>
-
Markos Chandras authored
Commit 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)") fixed indirect system calls on O32 but it also introduced a bug for MIPS64 where it erroneously modified the v0 (syscall) register with the assumption that the sycall offset hasn't been taken into consideration. This breaks seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition with a move instruction. Fixes: 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)") Cc: <stable@vger.kernel.org> # 3.15+ Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10951/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
- 15 Aug, 2015 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fixes from James Bottomley: "This has two libfc fixes for bugs causing rare crashes, one iscsi fix for a potential hang on shutdown, and a fix for an I/O blocksize issue which caused a regression" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: sd: Fix maximum I/O size for BLOCK_PC requests libfc: Fix fc_fcp_cleanup_each_cmd() libfc: Fix fc_exch_recv_req() error path libiscsi: Fix host busy blocking during connection teardown
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM fixes from Paolo Bonzini: "Just two very small & simple patches" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: Use adjustment in guest cycles when handling MSR_IA32_TSC_ADJUST KVM: x86: zero IDT limit on entry to SMM
-
Linus Torvalds authored
Merge fixes from Andrew Morton: "11 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: Update maintainers for DRM STI driver mm: cma: mark cma_bitmap_maxno() inline in header zram: fix pool name truncation memory-hotplug: fix wrong edge when hot add a new node .mailmap: Andrey Ryabinin has moved ipc/sem.c: update/correct memory barriers mm/hwpoison: fix panic due to split huge zero page ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem() ipc,sem: fix use after free on IPC_RMID after a task using same semaphore set exits mm/hwpoison: fix fail isolate hugetlbfs page w/ refcount held mm/hwpoison: fix page refcount of unknown non LRU page
-
- 14 Aug, 2015 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linuxLinus Torvalds authored
Pull clock fix from Stephen Boyd: "A one-liner for a regression found in the PXA clock driver" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: pxa: pxa3xx: fix CKEN register access
-
Benjamin Gaignard authored
Add Vincent Abriou and myself as maintainers. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Dave Airlie <airlied@linux.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Gregory Fong authored
cma_bitmap_maxno() was marked as static and not static inline, which can cause warnings about this function not being used if this file is included in a file that does not call that function, and violates the conventions used elsewhere. The two options are to move the function implementation back to mm/cma.c or make it inline here, and it's simple enough for the latter to make sense. Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-