- 23 Mar, 2010 3 commits
-
-
Kuninori Morimoto authored
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Kuninori Morimoto authored
Current ak4642 was not able to select pll. This patch add support it. It still expect PLL base input pin is MCKI. see Table 5 "setting of PLL Mode" of datasheet Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Mark Brown authored
This also adds the first DAI operation for AIF3 so fill out the ID and the ops for that too. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
- 22 Mar, 2010 9 commits
-
-
Mark Brown authored
-
Mark Brown authored
Don't force enable the microphone bias on WM8903 when doing jack detection, and don't force enable microphone bias. This allows platforms to only enable microphone detection when a jack has been inserted. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Mark Brown authored
If no report is specified then disable detection. Note that we don't disable the slow clock, though the power consumption from it should be negligable. That should be reference counted, ideally through DAPM. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Mark Brown authored
Allow machines to control exactly when the bias is turned on and off. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Mark Brown authored
Some systems, such as those with mechanical jack detection, may wish to force enable a pin (typically mic bias) only some of the time. Support such systems by having disable_pin() also coveer force enabled pins. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Mark Brown authored
Some systems provide both mechanical and electrical detection of jack status changes. On such systems power savings can be achieved by only enabling the electrical detection methods when physical insertion has been detected. Begin supporting such systems by providing a notifier for jack status changes which can be used to trigger any reconfiguration. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Peter Ujfalusi authored
Gain controls on outputs affect the power consumption when the gain is set to non 0 value. Outputs with amps have one register to configure the routing and the gain: PREDL_CTL (0x25): bit 0: Voice enable bit 1: Audio L1 enable bit 2: Audio L2 enable bit 3: Audio R2 enable bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB) bit 0 - 3: is handled in DAPM domain (DAPM_MIXER) bit 4 - 5: has simple volume control If there is no audio activity (BIAS_STANDBY), and user changes the volume, than the output amplifier will be enabled. If the user changes the routing (but the codec remains in BIAS_STANDBY), than the cached gain value also be written to the register, which enables the amplifier. The existing workaround for this is to have virtual PGAs associated with the outputs, and whit DAPM PMD the gain on the output will be forced to 0 (off) by bypassing the regcache. This failed to disable the amplifiers in several scenario (as mentioned above). Also if the codec is in BIAS_ON state, and user modifies a volume control, which path is actually not enabled, than that amplifier will be enabled as well, but it will be not turned off, since there is no DAPM path, which would make mute it. To prevent amps being enabled, when they are not needed, introduce the following workaround: Track the state of each of this type of output. In twl4030_write only allow actual write, when the given output is enabled, otherwise only update the reg_cache. The PGA event handlers on power up will write the cached value to the chip (restoring gain, routing selection). On power down 0 is written to the register (disabling the amp, and also just in case clearing the routing). Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Mark Brown authored
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Mark Brown authored
-
- 20 Mar, 2010 3 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: serial: sh-sci: remove duplicated #include sh: Export uncached helper symbols. sh: Fix up NUMA build for 29-bit. serial: sh-sci: Fix build failure for non-sh architectures. sh: Fix up uncached offset for legacy 29-bit mode. sh: Support CPU affinity masks for INTC controllers.
-
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwbLinus Torvalds authored
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: uwb: remove duplicate cpu_to_le16() uwb: declare MODULE_FIRMWARE() in i1480 DFU driver uwb: make USB device id table constant uwb: wlp: refactor wlp_get_<attribute>() macros
-
- 19 Mar, 2010 25 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6: alpha: fix compile errors in dma-mapping-common.h alpha: remove trailing spaces in messages alpha: use __ratelimit
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc: Remove IOMMU_VMERGE config option powerpc: Fix swiotlb to respect the boot option powerpc: Do not call prink when CONFIG_PRINTK is not defined powerpc: Use correct ccr bit for syscall error status powerpc/fsl-booke: Get coherent bit from PTE powerpc/85xx: Make sure lwarx hint isn't set on ppc32
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6Linus Torvalds authored
* 'zerolen' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6: Delete zero-length file drivers/mtd/maps/omap_nor.c
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: tty_port,usb-console: Fix usb serial console open/close regression tty: cpm_uart: use resource_size() tty_buffer: Fix distinct type warning hvc_console: Fix race between hvc_close and hvc_remove uartlite: Fix build on sparc. tty: Take a 256 byte padding into account when buffering below sub-page units Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: driver core: numa: fix BUILD_BUG_ON for node_read_distance driver-core: document ERR_PTR() return values kobject: documentation: Update to refer to kset-example.c. sysdev: the cpu probe/release attributes should be sysdev_class_attributes kobject: documentation: Fix erroneous example in kobject doc. driver-core: fix missing kernel-doc in firmware_class Driver core: Early platform kernel-doc update sysfs: fix sysfs lockdep warning in mlx4 code sysfs: fix sysfs lockdep warning in infiniband code sysfs: fix sysfs lockdep warning in ipmi code sysfs: Initialised pci bus legacy_mem field before use sysfs: use sysfs_bin_attr_init in firmware class driver
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (45 commits) USB: gadget/multi: cdc_do_config: remove redundant check usb: r8a66597-hcd: fix removed from an attached hub USB: xhci: Make endpoint interval debugging clearer. USB: Fix usb_fill_int_urb for SuperSpeed devices USB: cp210x: Remove double usb_control_msg from cp210x_set_config USB: Remove last bit of CONFIG_USB_BERRY_CHARGE USB: gadget: add gadget controller number for s3c-hsotg driver USB: ftdi_sio: Fix locking for change_speed() function USB: g_mass_storage: fixed module name in Kconfig USB: gadget: f_mass_storage::fsg_bind(): fix error handling USB: g_mass_storage: fix section mismatch warnings USB: gadget: fix Blackfin builds after gadget cleansing USB: goku_udc: remove potential null dereference USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff USB: serial: Fix module name typo for qcaux Kconfig entry. usb: cdc-wdm: Fix deadlock between write and resume usb: cdc-wdm: Fix order in disconnect and fix locking usb: cdc-wdm:Fix loss of data due to autosuspend usb: cdc-wdm: Fix submission of URB after suspension usb: cdc-wdm: Fix race between disconnect and debug messages ...
-
Mark Brown authored
-
Guennadi Liakhovetski authored
If instantiation of a card failed, we still have to remove it from the card list on unregistration. This fixes an Oops on Migo-R, triggering, when after a failed firmware load attempt the driver modules are removed and re-inserted again. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Daniel Mack authored
This fixes a memory corruption when ASoC devices are used in full-duplex mode. Specifically for pxa-ssp code, where this pointer is dynamically allocated for each direction and destroyed upon each stream start. All other platforms are fixed blindly, I couldn't even compile-test them. Sorry for any breakage I may have caused. Reported-by: Sven Neumann <s.neumann@raumfeld.com> Reported-by: Michael Hirsch <m.hirsch@raumfeld.com> Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Jeff Garzik authored
The content was deleted in cc87edb1, but the file remained as a zero-length file. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-clientLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (205 commits) ceph: update for write_inode API change ceph: reset osd after relevant messages timed out ceph: fix flush_dirty_caps race with caps migration ceph: include migrating caps in issued set ceph: fix osdmap decoding when pools include (removed) snaps ceph: return EBADF if waiting for caps on closed file ceph: set osd request message front length correctly ceph: reset front len on return to msgpool; BUG on mismatched front iov ceph: fix snaptrace decoding on cap migration between mds ceph: use single osd op reply msg ceph: reset bits on connection close ceph: remove bogus mds forward warning ceph: remove fragile __map_osds optimization ceph: fix connection fault STANDBY check ceph: invalidate_authorizer without con->mutex held ceph: don't clobber write return value when using O_SYNC ceph: fix client_request_forward decoding ceph: drop messages on unregistered mds sessions; cleanup ceph: fix comments, locking in destroy_inode ceph: move dereference after NULL test ... Fix trivial conflicts in Documentation/ioctl/ioctl-number.txt
-
git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: cifs: trivial white space [CIFS] checkpatch cleanup cifs: add cifs_revalidate_file cifs: add a CIFSSMBUnixQFileInfo function cifs: add a CIFSSMBQFileInfo function cifs: overhaul cifs_revalidate and rename to cifs_revalidate_dentry
-
Daniel Mack authored
This fixes a warning ("pxa_free_dma: trying to free channel 0 which is already freed") when a device was opened but the hw_params() call failed. Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Peter Korsgaard authored
cdc_do_config() had a double ret check after fsg_add(). Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Yoshihiro Shimoda authored
fix the problem that when a USB hub is attached to the r8a66597-hcd and a device is removed from that hub, it's likely that a kernel panic follows. Reported-by: Markus Pietrek <Markus.Pietrek@emtrion.de> Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Sarah Sharp authored
The xHCI hardware can only handle polling intervals that are a power of two. When we add a new endpoint during a bandwidth allocation, and the polling interval is rounded down to a power of two, print the original polling interval in the endpoint descriptor. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Matthew Wilcox authored
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint interval that matches the USB 2 specification. usb_fill_int_urb() didn't know that and was filling in the interval as if it was USB 1.1. Fix usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case alone, because David Vrabel wants to keep the old encoding. Update the struct urb kernel doc to note that SuperSpeed URBs must have urb->interval specified in microframes. Add a missing break statement in the usb_submit_urb() interrupt URB checking, since wireless USB and SuperSpeed USB encode urb->interval differently. This allows xHCI roothubs to actually register with khubd. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Michael Brunner authored
This patch removes a double usb_control_msg that sets the cp210x configuration registers a second time when calling cp210x_set_config. For data sizes >2 the second write gets corrupted. The patch has been created against 2.6.34-rc1, but all cp210x driver revisions are affected. Signed-off-by: Michael Brunner <mibru@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Christoph Egger authored
One last bit was missed while removing the USB_BERRY_CHARGE config option in a8d4211f which gets dropped by this patch. Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Maurus Cuelenaere authored
This prevents some drivers from complaining that no bcdDevice id was set. Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Alessio Igor Bogani authored
The change_speed() function should be serialized against multiple calls. Use the cfg_lock mutex to do this. Signed-off-by: Alessio Igor Bogani <abogani@texware.it> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Michal Nazarewicz authored
The Kconfig help message for Mass Storage Gadget claimed the module will be named "g_file_storage" whereas it should be "g_mass_storage". Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Peter Korsgaard authored
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors, which decreases refcount and frees the fsg_dev structure, causing trouble when fsg_add does the same. Fix it by simply leaving up cleanup to fsg_add(). Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Mike Frysinger authored
The recent commit (0e530b45) that moved usb_ep_autoconfig from the __devinit section to the __init section missed the mass storage device. Its fsg_bind() function uses the usb_ep_autoconfig() function from non __init context leading to: WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in reference from the function _fsg_bind() to the function .init.text:_usb_ep_autoconfig() So move fsg_bind() into __init as well. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Mike Frysinger authored
The recent change to clean out dead gadget drivers (90f79768) missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This causes Blackfin gadget builds to fail since the function no longer exists anywhere. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-