Now that the ibmvstgt driver as the only user of scsi_tgt is gone, the
scsi_tgt kernel module, the CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and
CONFIG_SCSI_FC_TGT_ATTRS kbuild variable, the scsi_host_template
transfer_response method are no longer needed.

[hch: minor updates to the current tree, changelog update]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>

Remove the libsrp module which was only used by the now removed ibmvstgt
driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>

The IBM virtual SCSI protocol has been obsoleted by ibmvfc, and there
are no reported of the driver left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>

Using dev_printk variants prefixes the logging message with
the originating device, which makes debugging easier.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Update the st driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Update the ch driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Update the sg driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Doug Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Update the sr driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

scsilun_to_int() has an error which prevents it from generating
correct LUN numbers for 64bit values.
Also we should remove the misleading comment about portions of
the LUN being ignored; the initiator should treat the LUN as
an opaque value.
And, finally, the example given should use the correct
prefix (here: extended flat space addressing scheme).

This patch includes the modifications suggested by
Bart van Assche.

Cc: Bart van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Some driver might want to pass in an 64-bit value, so introduce
a module param type 'ullong'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>

The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.

So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Older HBAs are only capable of supporting 16-bit LUNs,
so we need to make sure to adjust max_lun accordingly.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Sequential scan for more than 256 LUNs is very fragile as
LUNs might not be numbered sequentially after that point.

SAM revisions later than SCSI-3 impose a structure on
LUNs larger than 256, making LUN numbers between 256
and 16384 illegal.
SCSI-3, however allows for plain 64-bit numbers with
no internal structure.

So restrict sequential LUN scan to 256 LUNs and add a
new blacklist flag 'BLIST_SCSI3LUN' to scan up to
max_lun devices.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Obsolete; either use 'max_lun' if the host supports only a
limited number of LUNs or BLIST_NOLUN if the target has
problems addressing more than one LUN.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This addresses a problem reported by Vaughan Cao concerning
the correctness of the O_EXCL logic in the sg driver. POSIX
doesn't defined O_EXCL semantics on devices but "allow only
one open file descriptor at a time per sg device" is a rough
definition. The sg driver's semantics have been to wait
on an open() when O_NONBLOCK is not given and there are
O_EXCL headwinds. Nasty things can happen during that wait
such as the device being detached (removed). So multiple
locks are reworked in this patch making it large and hard
to break down into digestible bits.

This patch is against Linus's current git repository which
doesn't include any sg patches sent in the last few weeks.
Hence this patch touches as little as possible that it
doesn't need to and strips out most SCSI_LOG_TIMEOUT()
changes in v3 because Hannes said he was going to rework all
that stuff.

The sg3_utils package has several test programs written to
test this patch. See examples/sg_tst_excl*.cpp .

Not all the locks and flags in sg have been re-worked in
this patch, notably sg_request::done . That can wait for
a follow-up patch if this one meets with approval.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>

When the SG_IO ioctl was copied into the block layer and
later into the bsg driver, subtle differences emerged.

One difference is the way injected commands are queued through
the block layer (i.e. this is not SCSI device queueing nor SATA
NCQ). Summarizing:
   - SG_IO in the block layer: blk_exec*(at_head=false)
   - sg SG_IO: at_head=true
   - bsg SG_IO: at_head=true

Some time ago Boaz Harrosh introduced a sg v4 flag called
BSG_FLAG_Q_AT_TAIL to override the bsg driver default.
This patch does the equivalent for the sg driver.

ChangeLog:
     Introduce SG_FLAG_Q_AT_TAIL flag to cause commands
     to be injected into the block layer with
     at_head=false.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

 - remove the 16 byte CDB (SCSI command) length limit from the sg driver
   by handling longer CDBs the same way as the bsg driver. Remove comment
   from sg.h public interface about the cmd_len field being limited to 16
   bytes.
 - remove some dead code caused by this change
 - cleanup comment block at the top of sg.h, fix urls
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Until now the per-command transfer length has exclusively been gated by
the max_sectors parameter in the scsi_host template. Given that the size
of this parameter has been bumped to an unsigned int we have to be
careful not to exceed the target device's capabilities.

If the if the device specifies a Maximum Transfer Length in the Block
Limits VPD we'll use that value. Otherwise we'll use 0xffffffff for
devices that have use_16_for_rw set and 0xffff for the rest. We then
combine the chosen disk limit with max_sectors in the host template. The
smaller of the two will be used to set the max_hw_sectors queue limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

In init_sd function, if kmem_cache_create or mempool_create_slab_pools
calls fail, the error will not be correclty reported because
class_register previously set the value of err to 0.
Signed-off-by: Clément Calmels <clement.calmels@free.fr>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This is a fix for commit 39c60a09

  "sd: fix array cache flushing bug causing performance problems"

We must notify the block layer via q->flush_flags after a temporary change
of the cache_type to write through.  Without this, a SYNCHRONIZE CACHE
command will still be generated.  This patch factors out a helper that
can be called from sd_revalidate_disk and cache_type_store.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This change enables to test read/write commands with huge transfer
length such as 1GB.  For example:

	# modprobe scsi_debug dev_size_mb=1024 clustering=1 opts=1
	# cat /sys/block/$DEV/queue/max_hw_sectors_kb > \
		/sys/block/$DEV/queue/max_sectors_kb
	# fio --name=test --rw=write --bs=1g --size=1g --filename=/dev/$DEV \
		--mem=mmaphuge  --direct=1

The data type of max_sectors in scsi_host_template has been extended
to unsigned int by the previous change.  So we can increase it from
0xffff to 0xffffffff to allow such huge transfer length.

Also, this increases sg_tablesize and max_segment_size, otherwise the
maximum transfer length is limited to 64MB.
(sg_tablesize * max_segment_size = 256 * 256KB)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

max_sectors in struct Scsi_Host specifies maximum number of sectors
allowed in a single SCSI command.  The data type of max_sectors is
unsigned short, so the maximum transfer length per SCSI command is
limited to less than 256MB in 4096-bytes sector size. (0xffff * 4096)

This commit increases the SCSI mid level's limitation for max_sectors
upto the block layer's limitation for max_hw_sectors by extending the
data type of max_sectors in struct Scsi_Host and scsi_host_template,
so that SCSI lower level drivers can specify more than 0xffff.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This change makes the scsi disk driver handle the requests whose
transfer length is greater than 0xffff with READ_16 or WRITE_16.

However, this is a preparation for extending the data type of
max_sectors in struct Scsi_Host and scsi_host_template.  So, it is
impossible to happen this condition for now, because SCSI low-level
drivers can not specify max_sectors greater than 0xffff due to the
data type limitation.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This prevents integer overflow when converting the request queue's
max_sectors from sectors to bytes.  However, this is a preparation for
extending the data type of max_sectors in struct Scsi_Host and
scsi_host_template.  So, it is impossible to happen this integer
overflow for now, because SCSI low-level drivers can not specify
max_sectors greater than 0xffff due to the data type limitation.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

scsi_put_command() is either invoked before blk_start_request() or
after block layer processing has completed.  scsi_cmnd.abort_work
is scheduled from inside the SCSI timeout handler.  The block layer
guarantees that either the regular completion handler
(softirq_done_fn()) or the timeout handler (rq_timed_out_fn()) is
invoked but not both. This means that scsi_put_command() is never
invoked while abort_work is scheduled.  Hence remove the
cancel_delayed_work() call from scsi_put_command().

Similarly, scsi_abort_command() is only invoked from the SCSI
timeout handler. If scsi_abort_command() is invoked for a SCSI
command with the SCSI_EH_ABORT_SCHEDULED flag set this means that
scmd_eh_abort_handler() has already invoked scsi_queue_insert() and
hence that scsi_cmnd.abort_work is no longer pending. Hence also
remove the cancel_delayed_work() call from scsi_abort_command().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Steven Haber <steven@qumulo.com>
Tested-by: Steven Haber <steven@qumulo.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>

Pull Xen fixes from Konrad Rzeszutek Wilk:
 "Two fixes found during migration of PV guests.  David would be the one
  doing this pull but he is on vacation.

  Fixes:
   - fix console deadlock when resuming PV guests
   - fix regression hit when ballooning and resuming PV guests"

* tag 'stable/for-linus-3.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: set ballooned out pages as invalid in p2m
  xen/manage: fix potential deadlock when resuming the console

Merge tag 'trace-fixes-v3.16-rc5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "A few more fixes for ftrace infrastructure.

  I was cleaning out my INBOX and found two fixes from zhangwei from a
  year ago that were lost in my mail.  These fix an inconsistency
  between trace_puts() and the way trace_printk() works.  The reason
  this is important to fix is because when trace_printk() doesn't have
  any arguments, it turns into a trace_puts().  Not being able to enable
  a stack trace against trace_printk() because it does not have any
  arguments is quite confusing.  Also, the fix is rather trivial and low
  risk.

  While porting some changes to PowerPC I discovered that it still has
  the function graph tracer filter bug that if you also enable stack
  tracing the function graph tracer filter is ignored.  I fixed that up.

  Finally, Martin Lau, fixed a bug that would cause readers of the
  ftrace ring buffer to block forever even though it was suppose to be
  NONBLOCK"

This also includes the fix from an earlier pull request:

 "Oleg Nesterov fixed a memory leak that happens if a user creates a
  tracing instance, sets up a filter in an event, and then removes that
  instance.  The filter allocates memory that is never freed when the
  instance is destroyed"

* tag 'trace-fixes-v3.16-rc5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ring-buffer: Fix polling on trace_pipe
  tracing: Add TRACE_ITER_PRINTK flag check in __trace_puts/__trace_bputs
  tracing: Fix graph tracer with stack tracer on other archs
  tracing: Add ftrace_trace_stack into __trace_puts/__trace_bputs
  tracing: instance_rmdir() leaks ftrace_event_file->filter

Pull MTD fixes from Brian Norris:

 - Fix ELM suspend/resume

 - Reduce warnings if NAND ECC is too weak

 - Add CFI support for Sharp LH28F640BF NOR

   The last fix is coming in because other commits in the 3.16 cycle
   depended on this support.

* tag 'for-linus-20140716' of git://git.infradead.org/linux-mtd:
  mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR
  mtd: nand: reduce the warning noise when the ECC is too weak
  mtd: devices: elm: fix elm_context_save() and elm_context_restore() functions

Pull scheduler fixes from Ingo Molnar:
 "A cpufreq lockup fix and a compiler warning fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix compiler warnings
  x86, tsc: Fix cpufreq lockup

Pull perf fixes from Ingo Molnar:
 "Tooling fixes and an Intel PMU driver fixlet"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Do not allow optimized switch for non-cloned events
  perf/x86/intel: ignore CondChgd bit to avoid false NMI handling
  perf symbols: Get kernel start address by symbol name
  perf tools: Fix segfault in cumulative.callchain report

Pull sound fixes from Takashi Iwai:
 "Things seem to calm down so far, just a small few HD-audio fixes
  (regression fixes and a new codec ID addition) popping up"

* tag 'sound-3.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix broken PM due to incomplete i915 initialization
  ALSA: hda - Revert stream assignment order for Intel controllers
  ALSA: hda - Add new GPU codec ID 0x10de0070 to snd-hda
  ALSA: hda: Fix build warning

Pull quota fix from Jan Kara:
 "Fix locking of dquot shrinker"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  quota: missing lock in dqcache_shrink_scan()

Pull GPIO fix from Linus Walleij:
 "Fix up some merge confusion from the merge window"

* tag 'gpio-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mcp23s08: Eliminates redundant checking.

ring_buffer_poll_wait() should always put the poll_table to its wait_queue
even there is immediate data available.  Otherwise, the following epoll and
read sequence will eventually hang forever:

1. Put some data to make the trace_pipe ring_buffer read ready first
2. epoll_ctl(efd, EPOLL_CTL_ADD, trace_pipe_fd, ee)
3. epoll_wait()
4. read(trace_pipe_fd) till EAGAIN
5. Add some more data to the trace_pipe ring_buffer
6. epoll_wait() -> this epoll_wait() will block forever

~ During the epoll_ctl(efd, EPOLL_CTL_ADD,...) call in step 2,
  ring_buffer_poll_wait() returns immediately without adding poll_table,
  which has poll_table->_qproc pointing to ep_poll_callback(), to its
  wait_queue.
~ During the epoll_wait() call in step 3 and step 6,
  ring_buffer_poll_wait() cannot add ep_poll_callback() to its wait_queue
  because the poll_table->_qproc is NULL and it is how epoll works.
~ When there is new data available in step 6, ring_buffer does not know
  it has to call ep_poll_callback() because it is not in its wait queue.
  Hence, block forever.

Other poll implementation seems to call poll_wait() unconditionally as the very
first thing to do.  For example, tcp_poll() in tcp.c.

Link: http://lkml.kernel.org/p/20140610060637.GA14045@devbig242.prn2.facebook.com

Cc: stable@vger.kernel.org # 2.6.27
Fixes: 2a2cc8f7 "ftrace: allow the event pipe to be polled"
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Martin Lau <kafai@fb.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Commit 1ab6c499 (fs: convert fs shrinkers to new scan/count API)
accidentally removed locking from quota shrinker. Fix it -
dqcache_shrink_scan() should use dq_list_lock to protect the
scan on free_dquots list.

CC: stable@vger.kernel.org
Fixes: 1ab6c499Signed-off-by: Niu Yawei <yawei.niu@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>

The TRACE_ITER_PRINTK check in __trace_puts/__trace_bputs is missing,
so add it, to be consistent with __trace_printk/__trace_bprintk.
Those functions are all called by the same function: trace_printk().

Link: http://lkml.kernel.org/p/51E7A7D6.8090900@huawei.com

Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Pull fuse fixes from Miklos Szeredi:
 "This contains miscellaneous fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: replace count*size kzalloc by kcalloc
  fuse: release temporary page if fuse_writepage_locked() failed
  fuse: restructure ->rename2()
  fuse: avoid scheduling while atomic
  fuse: handle large user and group ID
  fuse: inode: drop cast
  fuse: ignore entry-timeout on LOOKUP_REVAL
  fuse: timeout comparison fix