This patch allows clients to roam multiple times within the same
originator-interval.

To enable this new feature two key aspects that have been introduced:
1) packets are always directed to the node that was originally
serving the roamed client which will then re-route the data
to the correct destination at any point in time;
2) the client flags handling mechanism has been properly modified
in order to allow multiple roamings withinin the same orig-int.
Therefore flags are now set properly even in this scenario.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

batadv_tt_global_del_struct() function is not properly named.
Having a more meaningful name which reflects the current behavior helps other
developers to easily understand what it does.

A parameter has also been renamed in order to let the function header better fit
the 80-chars line-width
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Antonio Quartulli <ordex@autistici.org>

tt_poss_change is a node-wide flag which tells whether the node is in a roaming
state (a client recently moved to/away from it) in order to let it apply special
re-routing rules. However this flag does not give a clear idea of the current
state because it is not possible to understand *which client* is actually
involved in the roaming. For this reason a better approach has been chosen:
instead of using a node-wide variable, the roaming state is now given by a
per-tt_entry ROAM flag which, in case of packet coming through the node, tells
the node whether the real destination is in roaming state or not.

With this flag change, batadv_check_unicast_ttvn() has also been rearranged in
order to better fit the new re-routing logic and to be much more readable.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

For some reasons (bridge forward delay, network device setup order, etc)
the initial bridge loop avoidance announcement packets may be lost. This
may lead to problems in finding other backbone gws, and therfore create
loops in the startup time.

Fix this by extending the waiting periods to 3 (define can be changed)
before allowing broadcast traffic.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

When adding a backbone gateway for the first time, it might not yet
be known in the backbone, and therefore we should not forward
broadcasts yet. This behaviour is the same as when sending a request
to another backbone gw because of a CRC mismatch. The backbone gw
will operate normal after the next periodic bla work.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

To avoid loops in the startup phase until the first announcement is
sent, send an announcement immediately as soon as a backbone gw is
added.

This may happen due to various reasons, e.g. a packet passes the rx
or tx path.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Any virtual device created on top of a batman-adv mesh interface must be
prevented to be used to create a new mesh network (this would lead to an
unwanted batman-over-batman configuration)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Signed-off-by: Antonio Quartulli <ordex@autistici.org>

The hash functions in the bridge loop avoidance code expects the
VLAN vid to be right after the mac address, but this is not guaranteed.

Fix this by explicitly hashing over the right fields of the struct.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

This patch is a follow-up for patch "net: filter: add vlan tag access"
to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is a follow-up for patch "filter: add XOR instruction for use
with X/K" that implements BPF ARM JIT parts for the BPF XOR operation.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds static declaration to several functions in bnx2x. It eliminates
newly introduced sparse warnings reported by Fengguang Wu.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces a new knob ndisc_notify. If enabled, the kernel
will transmit an unsolicited neighbour advertisement on link-layer address
change to update the neighbour tables of the corresponding hosts more quickly.

This is the equivalent to arp_notify in ipv4 world.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows users to enable and disable EEE using Ethtool.
It also allows users to get EEE settings, as supported by the device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change is meant to both improve the performance and reduce the size of
igb_tx_map.  To do this I have expanded the work done in the main loop by
pushing first into tx_buffer.  This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor.  The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change is meant to improve the efficiency of the Tx flags in igb by
aligning them with the values that will later be written into either the
cmd_type or olinfo.  By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.

In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads.  Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
igb_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides ability to enable or disable UDP RSS hashing. It gives
users option of generating RSS hash based on the UDP source and destination
ports numbers. Currently, UDP flow hash is always disabled in igb-driver.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Customers are requesting that the hw prevents PHY from establishing link
until the driver loads.  This patch clears the Go Link Disconnect bit which
provides the requested behavior on parts 82580 and later.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need to support up to 15k buffers since the HW is limited to
9.5k in SR-IOV mode.  Instead, allocate buffers that fit and align inside
of a 32K memory buffer.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_gro_receive shouldn't be called from netpoll context.  Doing
so was causing kernel panics when jumbo frames larger than 2K were set.
Add a flag to check if the Rx ring processing is occurring from interrupt
context or from netpoll context and call netif_rx() if in the polling
context.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves the following warning:

drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function ‘ixgbevf_probe’:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1742:290: warning: ‘err’ may be used uninitialized in this function [-Wuninitialized]
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1717:6: note: ‘err’ was declared here
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver cannot work without MSI-X interrupts
so there is no mechanism to fall back to.
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way the code was previously written it was causing DCA to prefetch the
entire packet into the cache when it was enabled.  That is excessive as we
only really need the headers.

We are now prefetching the headers via software so doing this from DCA would
be redundant anyway.  So clear the bit that was causing us to prefetch the
packet data and instead only use DCA for the descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since eab6d18d (vlan: Don't check for vlan group before
vlan_tx_tag_present.) we don't check tp->vlgrp and thus
tp is not needed in this function.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Signed-off-by: Dayanidhi Sreenivasan <dayanidhi.sreenivasan@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Conflicts:
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c

Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net.  Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>

It is usefull for daemons that monitor link event to have the full parameters of
these interfaces when a rtnl message is sent.
It allows also to dump them via rtnetlink.

It is based on what is done for GRE tunnels.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is usefull for daemons that monitor link event to have the full parameters of
these interfaces when a rtnl message is sent.
It allows also to dump them via rtnetlink.

It is based on what is done for GRE tunnels.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is usefull for daemons that monitor link event to have the full parameters of
these interfaces when a rtnl message is sent.
It allows also to dump them via rtnetlink.

It is based on what is done for GRE tunnels.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spotted after a code review.
Introduced by c12b395a (gre: Support GRE over
IPv6).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct spelling typo in printk within drivers/isdn
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.

For example:

	~# ifconfig eth0 down
	~# echo disk > /sys/power/state

	  <trigger a restore from hibernation>

	~# ifconfig eth0 up
	SIOCSIFFLAGS: No such device

This happens because the restore function bails out early upon
finding devices that were not up at hibernation.  In doing so,
it never gets to the netif_device_attach call at the end of
the restore function.  Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.

Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should gfar_init_bds() return with -ENOMEM inside gfar_alloc_skb_resources(),
free_skb_resources() will be called twice in a row on the "cleanup" path,
leading to duplicate kfree() calls for rx_|tx_queue->rx_|tx_skbuff resulting
in segmentation fault.
This patch prevents the segmentation fault to happen in the future
(rx_|tx_sbkbuff set to NULL), and corrects the error path handling
for gfar_init_bds().

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These can be converted to net_*_ratelimited().

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 6b78f16e (gre: add GSO support) we added GSO support to GRE
tunnels.

This patch does the same for IPIP tunnels.

Performance of single TCP flow over an IPIP tunnel is increased by 40%
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when something goes wrong, a flood of these messages can be
generated by usbnet (thousands per second).  This doesn't
generally *help* the condition so this patch ratelimits the
rate of their generation.

There's an underlying problem in usbnet's kevent deferral
mechanism which needs fixing, specifically that events *can*
get dropped and not handled.  This patch doesn't address this,
but just mitigates fallout caused by the current implemention.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>