- 21 Mar, 2019 4 commits
-
-
Dan Murphy authored
Add the DP83825I ethernet PHY to the DP83822 driver. These devices share the same WoL register bits and addresses. The phy_driver init was made into a macro as there may be future devices appended to this driver that will share the register space. http://www.ti.com/lit/gpn/dp83825iReviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Dan Murphy <dmurphy@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for your net tree: 1) Remove a direct dependency with IPv6 introduced by the sip_external_media feature, from Alin Nastac. 2) Fix bogus ENOENT when removing interval elements from set. 3) Set transport_header from br_netfilter to mimic the stack behaviour, this partially fixes a checksum validation bug from the SCTP connection tracking, from Xin Long. 4) Fix undefined reference to symbol in xt_TEE, due to missing Kconfig dependencies, from Arnd Bergmann. 5) Check for NULL in skb_header_pointer() calls in ip6t_shr, from Kangjie Lu. 6) Fix bogus EBUSY when removing an existing conntrack helper from a transaction. 7) Fix module autoload of the redirect extension. 8) Remove duplicated transition in flowtable diagram in the existing documentation. 9) Missing .release_ops call from error path in newrule() which results module refcount leak, from Taehee Yoo. ==================== Signed-off-by: -
YueHaibing authored
In genl_register_family(), when idr_alloc() fails, we forget to free the memory we possibly allocate for family->attrbuf. Reported-by:
Hulk Robot <hulkci@huawei.com> Fixes: 2ae0f17d ("genetlink: use idr to track families") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Erik Hugne authored
When cancelling a subscription, we have to clear the cancel bit in the request before iterating over any established subscriptions with memcmp. Otherwise no subscription will ever be found, and it will not be possible to explicitly unsubscribe individual subscriptions. Fixes: 8985ecc7 ("tipc: simplify endianness handling in topology subscriber") Signed-off-by:
Erik Hugne <erik.hugne@gmail.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
- 20 Mar, 2019 12 commits
-
-
Ioana Ciocoi Radulescu authored
Make sure we don't try to enqueue XDP_REDIRECT frames to an inexistent FQ. While it is guaranteed not to have more than one queue per core, having fewer queues than CPUs on an interface is a valid configuration. Fixes: d678be1d ("dpaa2-eth: add XDP_REDIRECT support") Reported-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by:
-
David S. Miller authored
Lukas Wunner says: ==================== ks8851 fixes & cleanups Four fixes and two cleanups for the Microchip (formerly Micrel) KSZ8851 SPI Ethernet driver. Some of the fixes might even pass as stable material, but I haven't marked them as such for cautiousness: Doesn't hurt letting them bake in linux-next for a few weeks to raise the confidence, even though we've tested them extensively on our Revolution Pi open source PLCs. ==================== Signed-off-by: -
Lukas Wunner authored
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or with a so-called non-PCI interface (KSZ8851-16MLL). When the driver for the latter was introduced with commit a55c0a0e ("drivers/net: ks8851_mll ethernet network driver"), it duplicated the register macros introduced by the driver for the former with commit 3ba81f3e ("net: Micrel KS8851 SPI network driver"). The chips are almost identical, so the duplication seems unwarranted. There are a handful of bits which are in use on the KSZ8851-16MLL but reserved on the KSZ8851SNL, and vice-versa, but there are no actual collisions. Thus, remove the duplicate definitions from the KSZ8851-16MLL driver. Mark all bits which differ between the two chips. Move the SPI frame opcodes, which are specific to KSZ8851SNL, to its driver. The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used. Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA. Signed-off-by:
Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by:
-
Lukas Wunner authored
In the header file accompanying the ks8851 driver, the P1SCLMD register macros are misnamed, they actually pertain to the P1CR register. The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68 of the spec: http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf The misnomers have no negative consequences so far because the macros aren't used by ks8851.c, but that's about to change. Signed-off-by:
-
Lukas Wunner authored
The ks8851 chip's initial carrier state is down. A Link Change Interrupt is signaled once interrupts are enabled if the carrier is up. The ks8851 driver has it backwards by assuming that the initial carrier state is up. The state is therefore misrepresented if the interface is opened with no cable attached. Fix it. The Link Change interrupt is sometimes not signaled unless the P1MBSR register (which contains the Link Status bit) is read on ->ndo_open(). This might be a hardware erratum. Read the register by calling mii_check_link(), which has the desirable side effect of setting the carrier state to down if the cable was detached while the interface was closed. Signed-off-by:
-
Lukas Wunner authored
The ks8851 driver currently requests the IRQ before registering the net_device. Because the net_device name is used as IRQ name and is still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs apart if multiple ks8851 chips are present. Most other drivers delay requesting the IRQ until the net_device is opened. Do the same. The driver doesn't enable interrupts on the chip before opening the net_device and disables them when closing it, so there doesn't seem to be a need to request the IRQ already on probe. Signed-off-by:
-
Lukas Wunner authored
Commit 73fdeb82 ("net: ks8851: Add optional vdd_io regulator and reset gpio") amended the ks8851 driver to briefly assert the chip's reset pin on probe. It also amended the probe routine's error path to reassert the reset pin if a subsequent initialization step fails. However the commit misplaced reassertion of the reset pin in the error path such that it is not performed if the check of the Chip ID and Enable Register (CIDER) fails. The error path is therefore slightly asymmetrical to the probe routine's body. Fix it. Signed-off-by:
-
Lukas Wunner authored
The ks8851 driver lets the chip auto-dequeue received packets once they have been read in full. It achieves that by setting the ADRFE flag in the RXQCR register ("Auto-Dequeue RXQ Frame Enable"). However if allocation of a packet's socket buffer or retrieval of the packet over the SPI bus fails, the packet will not have been read in full and is not auto-dequeued. Such partial retrieval of a packet confuses the chip's RX queue management: On the next RX interrupt, the first packet read from the queue will be the one left there previously and this one can be retrieved without issues. But for any newly received packets, the frame header status and byte count registers (RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval. The chip allows explicitly dequeueing a packet from the RX queue by setting the RRXEF flag in the RXQCR register ("Release RX Error Frame"). This could be used to dequeue the packet in case of an error, but if that error is a failed SPI transfer, it is unknown if the packet was transferred in full and was auto-dequeued or if it was only transferred in part and requires an explicit dequeue. The safest approach is thus to always dequeue packets explicitly and forgo auto-dequeueing. Without this change, I've witnessed packet retrieval break completely when an SPI DMA transfer fails, requiring a chip reset. Explicit dequeueing magically fixes this and makes packet retrieval absolutely robust for me. The chip's documentation suggests auto-dequeuing and uses the RRXEF flag only to dequeue error frames which the driver doesn't want to retrieve. But that seems to be a fair-weather approach. Signed-off-by: -
Xin Long authored
In sctp_setsockopt_bindx()/__sctp_setsockopt_connectx(), it allocates memory with addrs_size which is passed from userspace. We used flag GFP_USER to put some more restrictions on it in Commit cacc0621 ("sctp: use GFP_USER for user-controlled kmalloc"). However, since Commit c981f254 ("sctp: use vmemdup_user() rather than badly open-coding memdup_user()"), vmemdup_user() has been used, which doesn't check GFP_USER flag when goes to vmalloc_*(). So when addrs_size is a huge value, it could exhaust memory and even trigger oom killer. This patch is to use memdup_user() instead, in which GFP_USER would work to limit the memory allocation with a huge addrs_size. Note we can't fix it by limiting 'addrs_size', as there's no demand for it from RFC. Reported-by: syzbot+ec1b7575afef85a0e5ca@syzkaller.appspotmail.com Fixes: c981f254 ("sctp: use vmemdup_user() rather than badly open-coding memdup_user()") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Xin Long authored
Jianlin reported a crash: [ 381.484332] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068 [ 381.619802] RIP: 0010:fib6_rule_lookup+0xa3/0x160 [ 382.009615] Call Trace: [ 382.020762] <IRQ> [ 382.030174] ip6_route_redirect.isra.52+0xc9/0xf0 [ 382.050984] ip6_redirect+0xb6/0xf0 [ 382.066731] icmpv6_notify+0xca/0x190 [ 382.083185] ndisc_redirect_rcv+0x10f/0x160 [ 382.102569] ndisc_rcv+0xfb/0x100 [ 382.117725] icmpv6_rcv+0x3f2/0x520 [ 382.133637] ip6_input_finish+0xbf/0x460 [ 382.151634] ip6_input+0x3b/0xb0 [ 382.166097] ipv6_rcv+0x378/0x4e0 It was caused by the lookup function __ip6_route_redirect() returns NULL in fib6_rule_lookup() when ip6_create_rt_rcu() returns NULL. So we fix it by simply making ip6_create_rt_rcu() return ip6_null_entry instead of NULL. v1->v2: - move down 'fallback:' to make it more readable. Fixes: e873e4b9 ("ipv6: use fib6_info_hold_safe() when necessary") Reported-by:
Jianlin Shi <jishi@redhat.com> Suggested-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
David Ahern <dsahern@gmail.com> Acked-by:
Wei Wang <weiwan@google.com> Signed-off-by:
-
Christoph Paasch authored
Since commit fc62814d ("net/packet: fix 4gb buffer limit due to overflow check") one can now allocate packet ring buffers >= UINT_MAX. However, syzkaller found that that triggers a warning: [ 21.100000] WARNING: CPU: 2 PID: 2075 at mm/page_alloc.c:4584 __alloc_pages_nod0 [ 21.101490] Modules linked in: [ 21.101921] CPU: 2 PID: 2075 Comm: syz-executor.0 Not tainted 5.0.0 #146 [ 21.102784] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011 [ 21.103887] RIP: 0010:__alloc_pages_nodemask+0x2a0/0x630 [ 21.104640] Code: fe ff ff 65 48 8b 04 25 c0 de 01 00 48 05 90 0f 00 00 41 bd 01 00 00 00 48 89 44 24 48 e9 9c fe 3 [ 21.107121] RSP: 0018:ffff88805e1cf920 EFLAGS: 00010246 [ 21.107819] RAX: 0000000000000000 RBX: ffffffff85a488a0 RCX: 0000000000000000 [ 21.108753] RDX: 0000000000000000 RSI: dffffc0000000000 RDI: 0000000000000000 [ 21.109699] RBP: 1ffff1100bc39f28 R08: ffffed100bcefb67 R09: ffffed100bcefb67 [ 21.110646] R10: 0000000000000001 R11: ffffed100bcefb66 R12: 000000000000000d [ 21.111623] R13: 0000000000000000 R14: ffff88805e77d888 R15: 000000000000000d [ 21.112552] FS: 00007f7c7de05700(0000) GS:ffff88806d100000(0000) knlGS:0000000000000000 [ 21.113612] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 21.114405] CR2: 000000000065c000 CR3: 000000005e58e006 CR4: 00000000001606e0 [ 21.115367] Call Trace: [ 21.115705] ? __alloc_pages_slowpath+0x21c0/0x21c0 [ 21.116362] alloc_pages_current+0xac/0x1e0 [ 21.116923] kmalloc_order+0x18/0x70 [ 21.117393] kmalloc_order_trace+0x18/0x110 [ 21.117949] packet_set_ring+0x9d5/0x1770 [ 21.118524] ? packet_rcv_spkt+0x440/0x440 [ 21.119094] ? lock_downgrade+0x620/0x620 [ 21.119646] ? __might_fault+0x177/0x1b0 [ 21.120177] packet_setsockopt+0x981/0x2940 [ 21.120753] ? __fget+0x2fb/0x4b0 [ 21.121209] ? packet_release+0xab0/0xab0 [ 21.121740] ? sock_has_perm+0x1cd/0x260 [ 21.122297] ? selinux_secmark_relabel_packet+0xd0/0xd0 [ 21.123013] ? __fget+0x324/0x4b0 [ 21.123451] ? selinux_netlbl_socket_setsockopt+0x101/0x320 [ 21.124186] ? selinux_netlbl_sock_rcv_skb+0x3a0/0x3a0 [ 21.124908] ? __lock_acquire+0x529/0x3200 [ 21.125453] ? selinux_socket_setsockopt+0x5d/0x70 [ 21.126075] ? __sys_setsockopt+0x131/0x210 [ 21.126533] ? packet_release+0xab0/0xab0 [ 21.127004] __sys_setsockopt+0x131/0x210 [ 21.127449] ? kernel_accept+0x2f0/0x2f0 [ 21.127911] ? ret_from_fork+0x8/0x50 [ 21.128313] ? do_raw_spin_lock+0x11b/0x280 [ 21.128800] __x64_sys_setsockopt+0xba/0x150 [ 21.129271] ? lockdep_hardirqs_on+0x37f/0x560 [ 21.129769] do_syscall_64+0x9f/0x450 [ 21.130182] entry_SYSCALL_64_after_hwframe+0x49/0xbe We should allocate with __GFP_NOWARN to handle this. Cc: Kal Conley <kal.conley@dectris.com> Cc: Andrey Konovalov <andreyknvl@google.com> Fixes: fc62814d ("net/packet: fix 4gb buffer limit due to overflow check") Signed-off-by:
Christoph Paasch <cpaasch@apple.com> Signed-off-by:
-
Taehee Yoo authored
->release_ops() callback releases resources and this is used in error path. If nf_tables_newrule() fails after ->select_ops(), it should release resources. but it can not call ->destroy() because that should be called after ->init(). At this point, ->release_ops() should be used for releasing resources. Test commands: modprobe -rv xt_tcpudp iptables-nft -I INPUT -m tcp <-- error command lsmod Result: Module Size Used by xt_tcpudp 20480 2 <-- it should be 0 Fixes: b8e20400 ("netfilter: nft_compat: use .release_ops and remove list of extension") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
- 19 Mar, 2019 24 commits
-
-
Vinay K Nallamothu authored
This patch adds support for 6PE (RFC 4798) which uses IPv4-mapped IPv6 nexthop to connect IPv6 islands over IPv4 only MPLS network core. Prior to this fix, to find the link-layer destination mac address, 6PE enabled host/router was sending IPv6 ND requests for IPv4-mapped IPv6 nexthop address over the interface facing the IPv4 only core which wouldn't success as the core is IPv6 free. This fix changes that behavior on 6PE host to treat the nexthop as IPv4 address and send ARP requests whenever the next-hop address is an IPv4-mapped IPv6 address. Below topology illustrates the issue and how the patch addresses it. abcd::1.1.1.1 (lo) abcd::2.2.2.2 (lo) R0 (PE/host)------------------------R1--------------------------------R2 (PE/host) <--- IPv4 MPLS core ---> <------ IPv4 MPLS core --------> eth1 eth2 eth3 eth4 172.18.0.10 172.18.0.11 172.19.0.11 172.19.0.12 ffff::172.18.0.10 ffff::172.19.0.12 <------------------IPv6 MPLS tunnel ----------------------> R0 and R2 act as 6PE routers of IPv6 islands. R1 is IPv4 only with MPLS tunnels between R0,R1 and R1,R2. docker exec r0 ip -f inet6 route add abcd::2.2.2.2/128 nexthop encap mpls 100 via ::ffff:172.18.0.11 dev eth1 docker exec r2 ip -f inet6 route add abcd::1.1.1.1/128 nexthop encap mpls 200 via ::ffff:172.19.0.11 dev eth4 docker exec r1 ip -f mpls route add 100 via inet 172.19.0.12 dev eth3 docker exec r1 ip -f mpls route add 200 via inet 172.18.0.10 dev eth2 With the change, when R0 sends an IPv6 packet over MPLS tunnel to abcd::2.2.2.2, using ::ffff:172.18.0.11 as the nexthop, it does neighbor discovery for 172.18.18.0.11. Signed-off-by:Vinay K Nallamothu <nvinay@juniper.net> Tested-by:
Avinash Lingala <ar977m@att.com> Tested-by:
Aravind Srinivas Srinivasa Prabhakar <aprabh@juniper.net> Signed-off-by:
-
Arnd Bergmann authored
clang points out a harmless signed integer overflow: drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion] new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm; ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~ drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion] new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast; ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~ drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion] new_mode = SetRxFilter | RxStation | RxBroadcast; ~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~ Make the variable unsigned to avoid the overflow. Fixes: Linux-2.1.128pre1 Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Eric Dumazet authored
When a dual stack dccp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or inet6_iif() helper. Fixes: 3df80d93 ("[DCCP]: Introduce DCCPv6") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
When a dual stack tcp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or tcp_v6_iif() helper. Fixes: 1397ed35 ("ipv6: add flowinfo for tcp6 pkt_options for all cases") Fixes: df3687ff ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET") Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Aditya Pakki authored
In case of kmemdup failure while setting the service name the patch returns -ENOMEM upstream for processing. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Signed-off-by:
-
YueHaibing authored
In netdev_queue_add_kobject and rx_queue_add_kobject, if sysfs_create_group failed, kobject_put will call netdev_queue_release to decrease dev refcont, however dev_hold has not be called. So we will see this while unregistering dev: unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1 Reported-by:
-
Aaro Koskinen authored
When using 16K DMA buffers and ring mode, the DES3 refill is not working correctly as the function is using a bogus pointer for checking the private data. As a result stale pointers will remain in the RX descriptor ring, so DMA will now likely overwrite/corrupt some already freed memory. As simple reproducer, just receive some UDP traffic: # ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up # iperf3 -c 192.168.253.40 -u -b 0 -R If you didn't crash by now check the RX descriptors to find non-contiguous RX buffers: cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status [...] 1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e ^^^^^^^^^^^^^^^^^^^^^ 2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e ^^^^^^^^^^^^^^^^^^^^^ A simple ping test will now report bad data: # ping -s 8200 192.168.253.40 PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data. 8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms wrong data byte #8144 should be 0xd0 but was 0x88 Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer size is 16K. Fixes: 54139cf3 ("net: stmmac: adding multiple buffers for rx") Signed-off-by:
Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by:
Jose Abreu <joabreu@synopsys.com> Signed-off-by:
-
Arnd Bergmann authored
A recently added function in mlxsw triggers a harmless compiler warning: In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17, from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7: drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get': drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context] #define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125) ~~~~~^~~~~~ drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC' if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) { ^~~~~~~~~~~~~~~~~~~~~~~~~ The warning is normally disabled, but it would be nice to enable it to find real bugs, and there are no other known instances at the moment. Replace the negation with a zero-comparison, which also matches the comment above it. Fixes: d93c19a1 ("mlxsw: core: Add API for QSFP module temperature thresholds reading") Signed-off-by:Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-for-davem-2019-03-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 5.1 First set of fixes for 5.1. Lots of fixes for mt76 this time. iwlwifi * fix warning with do_div() mt7601u * avoid using hardware which is supported by mt76 mt76 * more fixes for hweight8() usage * fix hardware restart for mt76x2 * fix writing txwi on USB devices * fix (and disable by default) ED/CCA support on 76x2 * fix powersave issues on 7603 * fix return value check for ioremap on 7603 * fix duplicate USB device IDs ==================== Signed-off-by:
-
David S. Miller authored
Merge branch 'ieee802154-for-davem-2019-03-19' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan Stefan Schmidt says: ==================== pull-request: ieee802154 for net 2019-03-19 An update from ieee802154 for your *net* tree. Kangjie Lu fixed a potential NULL pointer deref in the adf7242 driver and Li RongQing make sure we propagate a netlink return code to the caller. ==================== Signed-off-by:
-
Stanislaw Gruszka authored
My commit 26a7b547 ("mt76x02: set protection according to ht operation element") enabled by default RTS/CTS protection for OFDM and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non 0xffff by initvals and .set_rts_threshold callback is not called by mac80211 on initialization, only on user request or during ieee80211_reconfig() (suspend/resuem or restart_hw). Enabling RTS/CTS cause some problems when sending probe request frames by hcxdumptool penetration tool, but I expect it can cause other issues on different scenarios. Restore previous setting of RTS/CTS being disabled by default for OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff. Fixes: 26a7b547 ("mt76x02: set protection according to ht operation element") Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Lorenzo Bianconi authored
Fix following schedule while atomic in mt76x02_reset_state since synchronize_rcu is run inside a RCU section [44036.944222] mt76x2e 0000:06:00.0: MCU message 31 (seq 3) timed out [44036.944281] BUG: sleeping function called from invalid context at kernel/rcu/tree_exp.h:818 [44036.944284] in_atomic(): 1, irqs_disabled(): 0, pid: 28066, name: kworker/u4:1 [44036.944287] INFO: lockdep is turned off. [44036.944292] CPU: 1 PID: 28066 Comm: kworker/u4:1 Tainted: G W 5.0.0-rc7-wdn-t1+ #7 [44036.944294] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009 [44036.944305] Workqueue: phy1 mt76x02_wdt_work [mt76x02_lib] [44036.944308] Call Trace: [44036.944317] dump_stack+0x67/0x90 [44036.944322] ___might_sleep.cold.88+0x9f/0xaf [44036.944327] rcu_blocking_is_gp+0x13/0x50 [44036.944330] synchronize_rcu+0x17/0x80 [44036.944337] mt76_sta_state+0x138/0x1d0 [mt76] [44036.944349] mt76x02_wdt_work+0x1c9/0x610 [mt76x02_lib] [44036.944355] process_one_work+0x2a5/0x620 [44036.944361] worker_thread+0x35/0x3e0 [44036.944368] kthread+0x11c/0x140 [44036.944376] ret_from_fork+0x3a/0x50 [44036.944384] BUG: scheduling while atomic: kworker/u4:1/28066/0x00000002 [44036.944387] INFO: lockdep is turned off. [44036.944389] Modules linked in: cmac ctr ccm af_packet snd_hda_codec_hdmi Introduce __mt76_sta_remove in order to run sta_remove without holding dev->mutex. Move __mt76_sta_remove outside of RCU section in mt76x02_reset_state Fixes: e4ebb8b403d1 ("mt76: mt76x2: implement full device restart on watchdog reset") Signed-off-by:Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Felix Fietkau authored
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled. The function that works on all architectures is hweight8(). Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
-
Stanislaw Gruszka authored
Since some USB device IDs are duplicated between mt76x0u, mt7601u and mt76x2u device, check chip version on probe and return error if not match the driver. Don't think this is serious issue, probe most likely will fail at some other point for wrong device, but we do not have to configure it if we know is not our device. Reported-by:
Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by:
-
Stanislaw Gruszka authored
Since some USB device IDs are duplicated between mt7601u and mt76x0u devices, check chip version on probe and return error if not match 0x7601. Don't think this is serious issue, probe most likely will fail at some other point for wrong device, but we do not have to configure it if we know is not mt7601u device. Reported-by:
Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
-
Stefan Schmidt authored
-
Pablo Neira Ayuso authored
No direct transition from prerouting to forward hook, routing lookup needs to happen first. Fixes: 19b351f1 ("netfilter: add flowtable documentation") Signed-off-by:
-
Florian Fainelli authored
Provide an explanation of what is expected with respect to sending new versions of specific patches within a patch series, as well as what happens if an earlier patch series accidentally gets merged). Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: fixes 2019-03-18 please apply the following three patches to -net. The first two are fixes for minor race conditions in the probe code, while the third one gets dropwatch working (again). ==================== Signed-off-by: -
Julian Wiedmann authored
As part of the TX completion path, qeth_release_skbs() frees the completed skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every completed skb as dropped. On the other hand when dropping an skb in .ndo_start_xmit, we end up calling consume_skb()... where we should be using kfree_skb() so that drop monitors get notified. Switch the drop/consume logic around, and also don't accumulate dropped packets in the tx_errors statistics. Fixes: dc149e37 ("s390/qeth: replace open-coded skb_queue_walk()") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
The ucast IP table is utilized by some of the L3-specific sysfs attributes that qeth_l3_create_device_attributes() provides. So initialize the table _before_ registering the attributes. Fixes: ebccc739 ("s390/qeth: add missing hash table initializations") Signed-off-by:
-
Julian Wiedmann authored
The HW trap and VNICC configuration is exposed via sysfs, and may have already been modified when qeth_l?_probe_device() attempts to initialize them. So (1) initialize the VNICC values a little earlier, and (2) don't bother about the HW trap mode, it was already initialized before. Signed-off-by:
-
Bjorn Helgaas authored
The device ID alone does not uniquely identify a device. Test both the vendor and device ID to make sure we don't mistakenly think some other vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device ID table. No functional change intended. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
David S. Miller authored
Xin Long says: ==================== sctp: fix ignoring asoc_id for tcp-style sockets on some setsockopts This is a patchset to fix ignoring asoc_id for tcp-style sockets on some setsockopts, introduced by SCTP_CURRENT_ASSOC of the patchset: [net-next,00/24] sctp: support SCTP_FUTURE/CURRENT/ALL_ASSOC (https://patchwork.ozlabs.org/cover/1031706/) As Marcelo suggested, we fix it on each setsockopt that is using SCTP_CURRENT_ASSOC one by one by adding the check: if (sctp_style(sk, TCP)) xxx.xxx_assoc_id = SCTP_FUTURE_ASSOC; so that assoc_id will be completely ingored for tcp-style socket on setsockopts, and works as SCTP_FUTURE_ASSOC. ==================== Signed-off-by:
-
