sdhci uses CONFIG_MMC_DEBUG for showing ADMA descriptor
when occurring ADMA error. And it's also used to  dump the
registers whenever calling sdhci_add_host.

On one hand, I don't see any burden to always print the state
ADMA descriptor as it's rare and will help folks better understand
what was happening when seeing ADMA error.

On the other, folks may be interested in checking some registers
at probe time. So we remove the sdhci_dumpregs from __sdhci_add_host
and print some really useful registers in sdhci_setup_host.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

wbsd only use this to print some unsupported command.
However the pr_warn should be enough for dynamic log
control and CONFIG_MMC_DEBUG seems bogus here. Remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We have removed all code depending on CONFIG_MMC_DEBUG
from mmc core now. So it's safe to make CONFIG_MMC_DEBUG
just for host drivers only and we expect to kill this option
in the future.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There are lots of debug message in core.c which use pr_debug
for better dynamic log level control. So it doesn't make sense
for those print to still keep working only under CONFIG_MMC_DEBUG.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

All the check within mmc_mrq_prep seems to be all-or-none
proposition, so it doesn't make sense to only check the
length of sglist only under the CONFIG_MMC_DEBUG context.
I'd prefer to always keep the check there unconditionally.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It was never used and introduce a warning

drivers/mmc/host/sdhci-acpi.c: In function 'sdhci_acpi_sdio_probe_slot':
drivers/mmc/host/sdhci-acpi.c:297:21: warning: variable 'host' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This increases consistency of the code across the sdhci family.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Acked-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

for_each_child_of_node performs an of_node_get on each iteration, so a
break out the loop requires an of_node_put.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
local idexpression n;
expression e,e1;
iterator name for_each_child_of_node;
@@

 for_each_child_of_node(e1,n) {
   ...
(
   of_node_put(n);
|
   e = n
|
+  of_node_put(n);
?  break;
)
   ...
 }
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This adds deepest (Backup+Self-Refresh) PM support to the ATMEL SAMA5D2
SoC's SDHCI controller.

When resuming from deepest state, it is required to restore preset
registers as the registers are lost since VDD core has been shut down
when entering deepest state on the SAMA5D2. The clocks need to be
reconfigured as well.

The other registers and init process are taken care of by the SDHCI
core.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The setting of clocks and presets is currently done in probe only but
once deep PM support is added, it'll be needed in the resume function.

Let's create a function for this setting.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We got a warning:

drivers/mmc/host/atmel-mci.c:1086:15: warning: variable 'sg_len' set but
not used [-Wunused-but-set-variable]

Ideally we should check to see if sg_len is zero but looking
into the code closely, I didn't find any possible to do that as
atmci_start_request didn't even deploy any error handling for
its host->prepare_data hook. So even we return error value for iflags
like what other host drivers did, for instance, sdhci and dwmmc, it still
need some extra work to improve the code.

Just remove it to silent the warning, although it isn't perfect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It was never used and leave a long standing compile warning:

drivers/mmc/host/sdhci-xenon.c: In function 'xenon_probe':
drivers/mmc/host/sdhci-xenon.c:447:21: warning: variable 'priv' set but
not used [-Wunused-but-set-variable]

Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It was never used and introduced a long standing compile
warning:

drivers/mmc/core/block.c: In function 'power_ro_lock_store':
drivers/mmc/core/block.c:191:19: warning: variable 'card' set but not
used [-Wunused-but-set-variable]

Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We got a compile warning for mxcmmc,

drivers/mmc/host/mxcmmc.c: In function 'mxcmci_data_done':
drivers/mmc/host/mxcmmc.c:661:6: warning: variable 'data_error' set but
not used [-Wunused-but-set-variable]

The easiest method is to remove the data_error. But looking into
the code closely, I think we should check the return value of
mxcmci_finish_data as if it got data->error(the same as data_error),
we shouldn't try to read the response.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Just a trivial fix for that found by reading the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

if user plug out sd card slowly, finally card is plugged out but
cat /proc/partitions can find that card is still exist in kernel.
that's because alougth get card detect interrupt but CMD13 still
can get correct response(all other pins are connected expect card
detect pin).
add ops->get_cd() can avoid this issue.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

array width is on-stack and not modified and should be
made static const.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Most registers need to wait until the command is completed, not
necessarily until the bus is free. At least, R-Car 2+ SoCs can signal
that via the CBSY bit, so let's use it there instead of SCLKDIVEN to
save a little bit of delay.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Our hardware engineers confirmed that it is unnecessary to wait when
turning the clock on/off. The documentation was a tad vague, so we
used to play safe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use a proper define.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When defining bits, make sure we always have a reference to the register
they belong to. For now, renaming all bits properly seems too intrusive,
so at least make sure we have proper documentation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Since commit 10c7fcbd ("ARM: shmobile: sh7372: Remove ZBOOT
MMC/SDHI support"), this define is not needed anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

I always anticipated this code to be not correct, but now I had a test
case to prove it. According to all documentation I have, setting the
TMIO_STOP_STP bit ever only worked during block transfers. This bit is
like manually enforcing an autocmd12 during a so far seamless transfer.
It does NOT work when the block transfer had errors. It also does NOT
work with any other cmd except block commands. For all those, CMD12 has
to be treated like any other command. So, basically, we could use this
bit only for mrq->data->stop cmds. But for these, we happily use the
autocmd12 feature using the TMIO_STOP_SEC bit. As a result, the above
bit is not useful for us and we need to treat CMD12 as a regular cmd
always. Just remove the special handling code. Note that the BSP
recognized this issue as well yet had a more cautious solution to the
problem [1]. Which is understandable but makes CMD12 handling even more
complicated.

Checked with a Renesas Salvator-X/M3-W which needed to send CMD12 when
retuning one of my SD cards.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas-bsp.git/commit/?id=2838a2ff8ca776f6d18b7fbbe75f3df8dd64183aSigned-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jan Klötzke <jan.kloetzke@preh.de>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

platform_get_irq() returns an error code, but the mxcmmc driver
ignores it and always returns -EINVAL. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.

Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Local variable transfer_error is assigned to a constant value and
it is never updated again.

Remove this variable and the dead code it guards.

Addresses-Coverity-ID: 1222110
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

shdci-st driver can be used for ppc476 fsp2 soc.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Reduce max_segs to 64, a value that allows allocation of an entire
EDMA descriptor list within a single page - EDMA descriptors
are 40 bytes and the header is much larger. This avoids doing a
higher order GFP_ATOMIC allocation in edma_prep_slave_sg
when setting up a transfer which can potentially fail due to
fragmentation under heavy I/O load.

The current value of 1024 is unusually high in comparison to
other mmc host drivers which mostly use values of between 1
and 256. The EDMA driver at present splits lists above 20
segments in any case so reducing the size of lists we pass to
it shouldn't add much overhead.
Signed-off-by: Will Newton <willn@resin.io>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add "rockchip,rk3228-dw-mshc", "rockchip,rk3288-dw-mshc" for
dwmmc on rk322x platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a new variant of the SDHI driver to support R-Car Gen3 with DMA via
on-chip bus mastering.  Since the DMAC is in a part of the SDHI module it
is not suitable to be used via DMA Engine.

Clearing of DM_CM_INFO1 after DMA thanks to Dirk Behme

Cc: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add dataend to DMA ops to allow DMAC implementation dependent
handling of DMA data end.

Also implement the operation for SDHI.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Allow TMIO and SDHI driver implementations to provide values for
max_segs and max_blk_count.

A follow-up patch will set these values for Renesas Gen3 SoCs
the using an SDHI driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  11586	    624	      0	  12210	   2fb2	drivers/mmc/host/omap_hsmmc.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  11778	    432	      0	  12210	   2fb2	drivers/mmc/host/omap_hsmmc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull IOMMU fix from Joerg Roedel:
 "Another fix, this time in common IOMMU sysfs code.

  In the conversion from the old iommu sysfs-code to the
  iommu_device_register interface, I missed to update the release path
  for the struct device associated with an IOMMU. It freed the 'struct
  device', which was a pointer before, but is now embedded in another
  struct.

  Freeing from the middle of allocated memory had all kinds of nasty
  side effects when an IOMMU was unplugged. Unfortunatly nobody
  unplugged and IOMMU until now, so this was not discovered earlier. The
  fix is to make the 'struct device' a pointer again"

* tag 'iommu-fixes-v4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu: Fix wrong freeing of iommu_device->dev

Pull char/misc fix from Greg KH:
 "Here is a single misc driver fix for 4.13-rc7. It resolves a reported
  problem in the Android binder driver due to previous patches in
  4.13-rc.

  It's been in linux-next with no reported issues"

* tag 'char-misc-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  ANDROID: binder: fix proc->tsk check.

Pull staging/iio fixes from Greg KH:
 "Here are few small staging driver fixes, and some more IIO driver
  fixes for 4.13-rc7. Nothing major, just resolutions for some reported
  problems.

  All of these have been in linux-next with no reported problems"

* tag 'staging-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: magnetometer: st_magn: remove ihl property for LSM303AGR
  iio: magnetometer: st_magn: fix status register address for LSM303AGR
  iio: hid-sensor-trigger: Fix the race with user space powering up sensors
  iio: trigger: stm32-timer: fix get trigger mode
  iio: imu: adis16480: Fix acceleration scale factor for adis16480
  PATCH] iio: Fix some documentation warnings
  staging: rtl8188eu: add RNX-N150NUB support
  Revert "staging: fsl-mc: be consistent when checking strcmp() return"
  iio: adc: stm32: fix common clock rate
  iio: adc: ina219: Avoid underflow for sleeping time
  iio: trigger: stm32-timer: add enable attribute
  iio: trigger: stm32-timer: fix get/set down count direction
  iio: trigger: stm32-timer: fix write_raw return value
  iio: trigger: stm32-timer: fix quadrature mode get routine
  iio: bmp280: properly initialize device for humidity reading