Currently DMA address width is either read from a RO device register
or force set from the platform data. This breaks DMA when the host DMA
address width is <=32it but the device is >32bit.

Right now the driver may decide to use a 2nd DMA descriptor for
another buffer (happens in case of TSO xmit) assuming that 32bit
addressing is used due to platform configuration but the device will
still use both descriptor addresses as one address.

This can be observed with the Intel EHL platform driver that sets
32bit for addr64 but the MAC reports 40bit. The TX queue gets stuck in
case of TCP with iptables NAT configuration on TSO packets.

The logic should be like this: Whatever we do on the host side (memory
allocation GFP flags) should happen with the host DMA width, whenever
we decide how to set addresses on the device registers we must use the
device DMA address width.

This patch renames the platform address width field from addr64 (term
used in device datasheet) to host_addr and uses this value exclusively
for host side operations while all chip operations consider the device
DMA width as read from the device register.

Fixes: 7cfc4486 ("stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing")
Signed-off-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
ACPI/DT mdiobus module owner fixes

This patch series fixes wrong mdiobus module ownership for MDIO buses
registered from DT or ACPI.

Thanks Maxime for providing the first patch and making me see that ACPI
also had the same issue.

Changes in v2:

- fixed missing kdoc in the first patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Bus ownership is wrong when using acpi_mdiobus_register() to register an
mdio bus. That function is not inline, so when it calls
mdiobus_register() the wrong THIS_MODULE value is captured.

CC: Maxime Bizon <mbizon@freebox.fr>
Fixes: 803ca24d ("net: mdio: Add ACPI support code for mdio")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bus ownership is wrong when using of_mdiobus_register() to register an mdio
bus. That function is not inline, so when it calls mdiobus_register() the wrong
THIS_MODULE value is captured.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
[florian: fix kdoc, added Fixes tag]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the phy_disconnect() -> phy_stop() path, we will be forcibly setting
the PHY state machine to PHY_HALTED. This invalidates the old_state !=
phydev->state condition in phy_state_machine() such that we will neither
display the state change for debugging, nor will we invoke the
link_change_notify() callback.

Factor the code by introducing phy_process_state_change(), and ensure
that we process the state change from phy_stop() as well.

Fixes: 5c5f626b ("net: phy: improve handling link_change_notify callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-03-16 (igb, igbvf, igc)

This series contains updates to igb, igbvf, and igc drivers.

Lin Ma removes rtnl_lock() when disabling SRIOV on remove which was
causing deadlock on igb.

Akihiko Odaki delays enabling of SRIOV on igb to prevent early messages
that could get ignored and clears MAC address when PF returns nack on
reset; indicating no MAC address was assigned for igbvf.

Gaosheng Cui frees IRQs in error path for igbvf.

Akashi Takahiro fixes logic on checking TAPRIO gate support for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In xirc2ps_probe, the local->tx_timeout_task was bounded
with xirc2ps_tx_timeout_task. When timeout occurs,
it will call xirc_tx_timeout->schedule_work to start the
work.

When we call xirc2ps_detach to remove the driver, there
may be a sequence as follows:

Stop responding to timeout tasks and complete scheduled
tasks before cleanup in xirc2ps_detach, which will fix
the problem.

CPU0                  CPU1

                    |xirc2ps_tx_timeout_task
xirc2ps_detach      |
  free_netdev       |
    kfree(dev);     |
                    |
                    | do_reset
                    |   //use dev

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have to make sure that the info returned by the helper is valid
before using it.

Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.

Fixes: f990c82c ("qed*: Add support for ndo_set_vf_trust")
Fixes: 733def6a ("qed*: IOV link control")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-03-16 (iavf)

This series contains updates to iavf driver only.

Alex fixes incorrect check against Rx hash feature and corrects payload
value for IPv6 UDP packet.

Ahmed removes bookkeeping of VLAN 0 filter as it always exists and can
cause a false max filter error message.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  iavf: do not track VLAN 0 filters
  iavf: fix non-tunneled IPv6 UDP packet type and hashing
  iavf: fix inverted Rx hash condition leading to disabled hash
====================

Link: https://lore.kernel.org/r/20230316155316.1554931-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The CPTS PPS GENf adjustment settings are invalid after it has been
disabled for a while, so reset them.

Fixes: eb9233ce ("net: ethernet: ti: am65-cpts: adjust pps following ptp changes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20230316095232.2002680-1-s-vadapalli@ti.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.

Fixes: 2f7ca802 ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230316101954.75836-1-szymon.heidrich@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

CPU port should also be enabled in order to get a working switch.

Fixes: a5538a77 ("net: dsa: b53: mmap: Add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230316172807.460146-1-noltari@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from netfilter, wifi and ipsec.

  A little more changes than usual, but it's pretty normal for us that
  the rc3/rc4 PRs are oversized as people start testing in earnest.

  Possibly an extra boost from people deploying the 6.1 LTS but that's
  more of an unscientific hunch.

  Current release - regressions:

   - phy: mscc: fix deadlock in phy_ethtool_{get,set}_wol()

   - virtio: vsock: don't use skbuff state to account credit

   - virtio: vsock: don't drop skbuff on copy failure

   - virtio_net: fix page_to_skb() miscalculating the memory size

  Current release - new code bugs:

   - eth: correct xdp_features after device reconfig

   - wifi: nl80211: fix the puncturing bitmap policy

   - net/mlx5e: flower:
      - fix raw counter initialization
      - fix missing error code
      - fix cloned flow attribute

   - ipa:
      - fix some register validity checks
      - fix a surprising number of bad offsets
      - kill FILT_ROUT_CACHE_CFG IPA register

  Previous releases - regressions:

   - tcp: fix bind() conflict check for dual-stack wildcard address

   - veth: fix use after free in XDP_REDIRECT when skb headroom is small

   - ipv4: fix incorrect table ID in IOCTL path

   - ipvlan: make skb->skb_iif track skb->dev for l3s mode

   - mptcp:
      - fix possible deadlock in subflow_error_report
      - fix UaFs when destroying unaccepted and listening sockets

   - dsa: mv88e6xxx: fix max_mtu of 1492 on 6165, 6191, 6220, 6250, 6290

  Previous releases - always broken:

   - tcp: tcp_make_synack() can be called from process context, don't
     assume preemption is disabled when updating stats

   - netfilter: correct length for loading protocol registers

   - virtio_net: add checking sq is full inside xdp xmit

   - bonding: restore IFF_MASTER/SLAVE flags on bond enslave Ethertype
     change

   - phy: nxp-c45-tja11xx: fix MII_BASIC_CONFIG_REV bit number

   - eth: i40e: fix crash during reboot when adapter is in recovery mode

   - eth: ice: avoid deadlock on rtnl lock when auxiliary device
     plug/unplug meets bonding

   - dsa: mt7530:
      - remove now incorrect comment regarding port 5
      - set PLL frequency and trgmii only when trgmii is used

   - eth: mtk_eth_soc: reset PCS state when changing interface types

  Misc:

   - ynl: another license adjustment

   - move the TCA_EXT_WARN_MSG attribute for tc action"

* tag 'net-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
  selftests: bonding: add tests for ether type changes
  bonding: restore bond's IFF_SLAVE flag if a non-eth dev enslave fails
  bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change
  net: renesas: rswitch: Fix GWTSDIE register handling
  net: renesas: rswitch: Fix the output value of quote from rswitch_rx()
  ethernet: sun: add check for the mdesc_grab()
  net: ipa: fix some register validity checks
  net: ipa: kill FILT_ROUT_CACHE_CFG IPA register
  net: ipa: add two missing declarations
  net: ipa: reg: include <linux/bug.h>
  net: xdp: don't call notifiers during driver init
  net/sched: act_api: add specific EXT_WARN_MSG for tc action
  Revert "net/sched: act_api: move TCA_EXT_WARN_MSG to the correct hierarchy"
  net: dsa: microchip: fix RGMII delay configuration on KSZ8765/KSZ8794/KSZ8795
  ynl: make the tooling check the license
  ynl: broaden the license even more
  tools: ynl: make definitions optional again
  hsr: ratelimit only when errors are printed
  qed/qed_mng_tlv: correctly zero out ->min instead of ->hour
  selftests: net: devlink_port_split.py: skip test if no suitable device available
  ...

Pull block fixes from Jens Axboe:
 "A bit bigger than usual, as the NVMe pull request missed last weeks
  submission. In detail:

   - NVMe pull request via Christoph:
        - Avoid potential UAF in nvmet_req_complete (Damien Le Moal)
        - More quirks (Elmer Miroslav Mosher Golovin, Philipp Geulen)
        - Fix a memory leak in the nvme-pci probe teardown path
          (Irvin Cote)
        - Repair the MAINTAINERS entry (Lukas Bulwahn)
        - Fix handling single range discard request (Ming Lei)
        - Show more opcode names in trace events (Minwoo Im)
        - Fix nvme-tcp timeout reporting (Sagi Grimberg)

   - MD pull request via Song:
        - Two fixes for old issues (Neil)
        - Resource leak in device stopping (Xiao)

   - Bio based device stats fix (Yu)

   - Kill unused CONFIG_BLOCK_COMPAT (Lukas)

   - sunvdc missing mdesc_grab() failure check (Liang)

   - Fix for reversal of request ordering upon issue for certain cases
     (Jan)

   - null_blk timeout fixes (Damien)

   - Loop use-after-free fix (Bart)

   - blk-mq SRCU fix for BLK_MQ_F_BLOCKING devices (Chris)"

* tag 'block-6.3-2023-03-16' of git://git.kernel.dk/linux:
  block: remove obsolete config BLOCK_COMPAT
  md: select BLOCK_LEGACY_AUTOLOAD
  block: count 'ios' and 'sectors' when io is done for bio-based device
  block: sunvdc: add check for mdesc_grab() returning NULL
  nvmet: avoid potential UAF in nvmet_req_complete()
  nvme-trace: show more opcode names
  nvme-tcp: add nvme-tcp pdu size build protection
  nvme-tcp: fix opcode reporting in the timeout handler
  nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM620
  nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV3000
  nvme-pci: fixing memory leak in probe teardown path
  nvme: fix handling single range discard request
  MAINTAINERS: repair malformed T: entries in NVM EXPRESS DRIVERS
  block: null_blk: cleanup null_queue_rq()
  block: null_blk: Fix handling of fake timeout request
  blk-mq: fix "bad unlock balance detected" on q->srcu in __blk_mq_run_dispatch_ops
  loop: Fix use-after-free issues
  block: do not reverse request order when flushing plug list
  md: avoid signed overflow in slot_store()
  md: Free resources in __md_stop

Pull io_uring fixes from Jens Axboe:

 - When PF_NO_SETAFFINITY was removed for io-wq threads, we kind of
   forgot about the SQPOLL thread. Remove it there as well, there's even
   less of a reason to set it there (Michal)

 - Fixup a confusing 'ret' setting (Li)

 - When MSG_RING is used to send a direct descriptor to another ring,
   it's possible to have it allocate it on the target ring rather than
   provide a specific index for it. If this is done, return the chosen
   value in the CQE, like we would've done locally (Pavel)

 - Fix a regression in this series on huge page bvec collapsing (Pavel)

* tag 'io_uring-6.3-2023-03-16' of git://git.kernel.dk/linux:
  io_uring/rsrc: fix folio accounting
  io_uring/msg_ring: let target know allocated index
  io_uring: rsrc: Optimize return value variable 'ret'
  io_uring/sqpoll: Do not set PF_NO_SETAFFINITY on sqpoll threads

Pull power management fixes from Rafael Wysocki:
 "These fix an error code path issue in a cpuidle driver and make the
  sleepgraph utility more robust against unexpected input.

  Specifics:

   - Fix the psci_pd_init_topology() failure path in the PSCI cpuidle
     driver (Shawn Guo)

   - Modify the sleepgraph utility so it does not crash on binary data
     in device names (Todd Brandt)"

* tag 'pm-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  pm-graph: sleepgraph: Avoid crashing on binary data in device names
  cpuidle: psci: Iterate backwards over list in psci_pd_remove()

Pull ACPI fixes from Rafael Wysocki:
 "These add some new quirks, fix PPTT handling, fix an ACPI utility and
  correct a mistake in the ACPI documentation.

  Specifics:

   - Fix ACPI PPTT handling to avoid sleep in the atomic context when it
     is not present (Sudeep Holla)

   - Add 'backlight=native' DMI quirk for Dell Vostro 15 3535 to the
     ACPI video driver (Chia-Lin Kao)

   - Add ACPI quirks for I2C device enumeration on Lenovo Yoga Book X90
     and Acer Iconia One 7 B1-750 (Hans de Goede)

   - Fix handling of invalid command line option values in the ACPI
     pfrut utility (Chen Yu)

   - Fix references to I2C device data type in the ACPI documentation
     for device enumeration (Andy Shevchenko)"

* tag 'acpi-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: tools: pfrut: Check if the input of level and type is in the right numeric range
  ACPI: PPTT: Fix to avoid sleep in the atomic context when PPTT is absent
  ACPI: x86: Add skip i2c clients quirk for Lenovo Yoga Book X90
  ACPI: x86: Add skip i2c clients quirk for Acer Iconia One 7 B1-750
  ACPI: x86: Introduce an acpi_quirk_skip_gpio_event_handlers() helper
  ACPI: video: Add backlight=native DMI quirk for Dell Vostro 15 3535
  ACPI: docs: enumeration: Correct reference to the I²C device data type

Pull turbostat fweaks and fixes from Len Brown:
 "Leprechaun sized fixes and tweaks touching only turbostat.

  'Keeping happy users happy since 2010'"

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: version 2023.03.17
  tools/power turbostat: fix decoding of HWP_STATUS
  tools/power turbostat: Introduce support for EMR
  tools/power turbostat: remove stray newlines from warn/warnx strings
  tools/power turbostat: Fix /dev/cpu_dma_latency warnings
  tools/power turbostat: Provide better debug messages for failed capabilities accesses
  tools/power turbostat: update dump of SECONDARY_TURBO_RATIO_LIMIT

Pull xen fixes from Juergen Gross:

 - cleanup for xen time handling

 - enable the VGA console in a Xen PVH dom0

 - cleanup in the xenfs driver

* tag 'for-linus-6.3-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen: remove unnecessary (void*) conversions
  x86/PVH: obtain VGA console info in Dom0
  x86/xen/time: cleanup xen_tsc_safe_clocksource
  xen: update arch/x86/include/asm/xen/cpuid.h

Pull RISC-V fixes from Palmer Dabbelt:

 - fixes to the ASID allocator to avoid leaking stale mappings between
   tasks

 - fix the vmalloc fault handler to tolerate huge pages

* tag 'riscv-for-linus-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: mm: Support huge page in vmalloc_fault()
  riscv: asid: Fixup stale TLB entry cause application crash
  Revert "riscv: mm: notify remote harts about mmu cache updates"

Pull s390 fixes from Vasily Gorbik:

 - Update defconfigs

 - Fix early boot code by adding missing intersection check to prevent
   potential overwriting of the ipl report

 - Fix a use-after-free issue in s390-specific code related to PCI
   resources being retained after hot-unplugging individual functions,
   by removing the resources from the PCI bus's resource list and using
   the zpci_bar_struct's resource pointer directly

* tag 's390-6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: update defconfigs
  PCI: s390: Fix use-after-free of PCI resources with per-function hotplug
  s390/ipl: add missing intersection check to ipl_report handling

Pull powerpc fixes from Michael Ellerman:

 - Fix false detection of read faults, introduced by execute-only
   support

 - Fix a build failure when GENERIC_ALLOCATOR is not selected

Thanks to Russell Currey, Randy Dunlap, Michal Suchánek, Nathan Lynch,
and Benjamin Gray.

* tag 'powerpc-6.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Fix false detection of read faults
  powerpc/pseries: RTAS work area requires GENERIC_ALLOCATOR

Pull MMC host fixes from Ulf Hansson:

 - dw_mmc-starfive: Fix initialization of the prev_err variable

 - sdhci_am654: Lower power-on failed message severity

* tag 'mmc-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: dw_mmc-starfive: Fix initialization of prev_err
  mmc: sdhci_am654: lower power-on failed message severity

Pull sound fixes from Takashi Iwai:
 "Nothing surprising, a collection of small device-specific fixes.

  The majority of changes are for ASoC Intel stuff, while a few other
  ASoC and HD-audio fixes are found"

* tag 'sound-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
  ALSA: hda/ca0132: fixup buffer overrun at tuning_ctl_set()
  ALSA: asihpi: check pao in control_message()
  ASoC: hdmi-codec: only startup/shutdown on supported streams
  ASoC: da7219: Initialize jack_det_mutex
  ALSA: hda: Match only Intel devices with CONTROLLER_IN_GPU()
  ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book2 Pro
  ALSA: hda/realtek: fix speaker, mute/micmute LEDs not work on a HP platform
  ALSA: hda: intel-dsp-config: add MTL PCI id
  ASoC: SOF: IPC4: update gain ipc msg definition to align with fw
  ASoC: SOF: sof-audio: don't squelch errors in WIDGET_SETUP phase
  ASoC: SOF: Intel: hda-ctrl: re-add sleep after entering and exiting reset
  ASoC: SOF: Intel: hda-dsp: harden D0i3 programming sequence
  ASoC: SOF: ipc4-topology: set dmic dai index from copier
  ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP
  ASoC: SOF: Intel: pci-tng: revert invalid bar size setting
  ASoC: SOF: topology: Fix error handling in sof_widget_ready()
  ASoC: Intel: soc-acpi: fix copy-paste issue in topology names
  ASoC: SOF: ipc4-topology: Fix incorrect sample rate print unit
  ASoC: SOF: ipc3: Check for upper size limit for the received message
  ASOC: SOF: Intel: pci-tgl: Fix device description
  ...

Pull drm fixes from Dave Airlie:
 "Seems like a pretty regular rc3, i915 and amdgpu with the usual
  selection of fixes, then a scattering of fixes across misc drivers and
  other areas:

  accel:
   - build fix for accel

  edid:
   - fix info leak in edid

  ttm:
   - fix NULL ptr deref
   - reference counting fix

  i915:
   - Fix hwmon PL1 power limit enabling
   - Fix audio ELD handling for DP MST
   - Fix PSR io and wake line calculations
   - Fix DG2 HDMI modes with 267.30 and 319.89 MHz pixel clocks
   - Fix SSEU subslice out-of-bounds access
   - Fix misuse of non-idle barriers as fence trackers

  amdgpu:
   - SMU 13 update
   - RDNA2 suspend/resume fix when overclocking is enabled
   - SRIOV VCN fixes
   - HDCP suspend/resume fix
   - Fix drm polling splat regression
   - Fix dirty rectangle tracking for PSR
   - Fix vangogh regression on certain BIOSes
   - Misc display fixes
   - Suspend/resume IOMMU regression fix

  amdkfd:
   - Fix BO offset for multi-VMA page migration
   - Fix a possible double free
   - Fix potential use after free
   - Fix process cleanup on module exit

  bridge:
   - fix returned array size name documentation

  fbdev:
   - ref-counting fix for fbdev deferred I/O

  virtio:
   - dma sync fix

  shmem-helper:
   - error path fix

  msm:
   - shrinker blocking fix

  panfrost:
   - shrinker rpm fix

  chipsfb:
   - fix error code

  meson:
   - fix 1px pink line
   - fix regulator interaction

  sun4i:
   - fix missing component unbind"

* tag 'drm-fixes-2023-03-17' of git://anongit.freedesktop.org/drm/drm: (38 commits)
  drm/ttm: drop extra ttm_bo_put in ttm_bo_cleanup_refs
  drm/amdgpu: Don't resume IOMMU after incomplete init
  drm/amdkfd: Fixed kfd_process cleanup on module exit.
  drm/amd/display: disconnect MPCC only on OTG change
  drm/amd/display: Fix DP MST sinks removal issue
  drm/amd/display: Do not set DRR on pipe Commit
  drm/amd/display: Remove OTG DIV register write for Virtual signals.
  drm/meson: dw-hdmi: Fix devm_regulator_*get_enable*() conversion again
  drm/bridge: Fix returned array size name for atomic_get_input_bus_fmts kdoc
  drm/amdgpu/vcn: Disable indirect SRAM on Vangogh broken BIOSes
  drm/amdgpu/nv: fix codec array for SR_IOV
  drm/amd/display: Write to correct dirty_rect
  drm/amdgpu: move poll enabled/disable into non DC path
  drm/amd/display: Fix HDCP failing to enable after suspend
  drm/amdkfd: fix potential kgd_mem UAFs
  drm/amdgpu/vcn: custom video info caps for sriov
  drm/amd/pm: Fix sienna cichlid incorrect OD volage after resume
  drm/amd/pm: bump SMU 13.0.4 driver_if header version
  drm/amdkfd: fix a potential double free in pqm_create_queue
  drm/amdkfd: Get prange->offset after svm_range_vram_node_new
  ...

Pull SCSI fixes from James Bottomley:
 "Ten patches, eight in drivers and two in the core, which correct a
  regression from directory removal and add a no VPD size quirk also to
  fix a regression. All pretty small"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: mcq: Use active_reqs to check busy in clock scaling
  scsi: core: Fix a procfs host directory removal regression
  scsi: core: Add BLIST_NO_VPD_SIZE for some VDASD
  scsi: mpi3mr: Fix expander node leak in mpi3mr_remove()
  scsi: mpi3mr: Fix memory leaks in mpi3mr_init_ioc()
  scsi: mpi3mr: Fix sas_hba.phy memory leak in mpi3mr_remove()
  scsi: mpi3mr: Fix mpi3mr_hba_port memory leak in mpi3mr_remove()
  scsi: mpi3mr: Fix config page DMA memory leak
  scsi: mpi3mr: Fix throttle_groups memory leak
  scsi: mpt3sas: Fix NULL pointer access in mpt3sas_transport_port_add()

Merge a PSCI cpuidle driver fix for 6.3-rc1:

 - Fix the psci_pd_init_topology() failure path in the PSCI cpuidle
   driver (Shawn Guo).

* pm-cpuidle:
  cpuidle: psci: Iterate backwards over list in psci_pd_remove()

Merge a new ACPI backlight quirk, new ACPI quirks for I2C device
enumeration on some platforms, a pfrut utility fix and an ACPI
documentation fix for 6.3-rc3:

 - Add backlight=native DMI quirk for Dell Vostro 15 3535 to the ACPI
   video driver (Chia-Lin Kao).

 - Add ACPI quirks for I2C devices enumeration on Lenovo Yoga Book X90
   and Acer Iconia One 7 B1-750 (Hans de Goede).

 - Fix handling of invalid command line option values in the ACPI pfrut
   utility (Chen Yu).

 - Fix references to I2C device data type in the ACPI documentation for
   device enumeration (Andy Shevchenko).

* acpi-video:
  ACPI: video: Add backlight=native DMI quirk for Dell Vostro 15 3535

* acpi-x86:
  ACPI: x86: Add skip i2c clients quirk for Lenovo Yoga Book X90
  ACPI: x86: Add skip i2c clients quirk for Acer Iconia One 7 B1-750
  ACPI: x86: Introduce an acpi_quirk_skip_gpio_event_handlers() helper

* acpi-tools:
  ACPI: tools: pfrut: Check if the input of level and type is in the right numeric range

* acpi-docs:
  ACPI: docs: enumeration: Correct reference to the I²C device data type

Happy St. Patrick's Day!
Signed-off-by: Len Brown <len.brown@intel.com>

The "excursion to minimum" information is in bit2
in HWP_STATUS MSR. Fix the bitmask used for
decoding the register.
Signed-off-by: Antti Laakso <antti.laakso@intel.com>
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Introduce support for EMR.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

warn(3) terminates strings with newlines
Signed-off-by: Len Brown <len.brown@intel.com>

When running as non-root the following error is seen in turbostat:

turbostat: fopen /dev/cpu_dma_latency
: Permission denied

turbostat and the man page have information on how to avoid other
permission errors, so these can be fixed the same way.

Provide better /dev/cpu_dma_latency warnings that provide instructions on
how to avoid the error, and update the man page.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>

turbostat reports some capabilities access errors and not others.  Provide
the same debug message for all errors.

[lenb: remove extra quotes]

Cc: David Arcari <darcari@redhat.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>

cosmetic only (but useful if you copy/paste)
Signed-off-by: Len Brown <len.brown@intel.com>

Nikolay Aleksandrov says:

====================
bonding: properly restore flags when bond changes ether type

A bug was reported by syzbot[1] that causes a warning and a myriad of
other potential issues if a bond, that is also a slave, fails to enslave a
non-eth device. While fixing that bug I found that we have the same
issues when such enslave passes and after that the bond changes back to
ARPHRD_ETHER (again due to ether_setup). This set fixes all issues by
extracting the ether_setup() sequence in a helper which does the right
thing about bond flags when it needs to change back to ARPHRD_ETHER. It
also adds selftests for these cases.

Patch 01 adds the new bond_ether_setup helper and fixes the issues when a
bond device changes its ether type due to successful enslave. Patch 02
fixes the issues when it changes its ether type due to an unsuccessful
enslave. Note we need two patches because the bugs were introduced by
different commits. Patch 03 adds the new selftests.

Due to the comment adjustment and squash, could you please review
patch 01 again? I've kept the other acks since there were no code
changes.

v3: squash the helper patch and the first fix, adjust the comment above
    it to be explicit about the bond device, no code changes
v2: new set, all patches are new due to new approach of fixing these bugs

[1] https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3ef
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new network selftests for the bonding device which exercise the ether
type changing call paths. They also test for the recent syzbot bug[1] which
causes a warning and results in wrong device flags (IFF_SLAVE missing).
The test adds three bond devices and a nlmon device, enslaves one of the
bond devices to the other and then uses the nlmon device for successful
and unsuccesful enslaves both of which change the bond ether type. Thus
we can test for both MASTER and SLAVE flags at the same time.

If the flags are properly restored we get:
TEST: Change ether type of an enslaved bond device with unsuccessful enslave   [ OK ]
TEST: Change ether type of an enslaved bond device with successful enslave   [ OK ]

[1] https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3efSigned-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported a warning[1] where the bond device itself is a slave and
we try to enslave a non-ethernet device as the first slave which fails
but then in the error path when ether_setup() restores the bond device
it also clears all flags. In my previous fix[2] I restored the
IFF_MASTER flag, but I didn't consider the case that the bond device
itself might also be a slave with IFF_SLAVE set, so we need to restore
that flag as well. Use the bond_ether_setup helper which does the right
thing and restores the bond's flags properly.

Steps to reproduce using a nlmon dev:
 $ ip l add nlmon0 type nlmon
 $ ip l add bond1 type bond
 $ ip l add bond2 type bond
 $ ip l set bond1 master bond2
 $ ip l set dev nlmon0 master bond1
 $ ip -d l sh dev bond1
 22: bond1: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noqueue master bond2 state DOWN mode DEFAULT group default qlen 1000
 (now bond1's IFF_SLAVE flag is gone and we'll hit a warning[3] if we
  try to delete it)

[1] https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3ef
[2] commit 7d5cd2ce ("bonding: correctly handle bonding type change on enslave failure")
[3] example warning:
 [   27.008664] bond1: (slave nlmon0): The slave device specified does not support setting the MAC address
 [   27.008692] bond1: (slave nlmon0): Error -95 calling set_mac_address
 [   32.464639] bond1 (unregistering): Released all slaves
 [   32.464685] ------------[ cut here ]------------
 [   32.464686] WARNING: CPU: 1 PID: 2004 at net/core/dev.c:10829 unregister_netdevice_many+0x72a/0x780
 [   32.464694] Modules linked in: br_netfilter bridge bonding virtio_net
 [   32.464699] CPU: 1 PID: 2004 Comm: ip Kdump: loaded Not tainted 5.18.0-rc3+ #47
 [   32.464703] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.1-2.fc37 04/01/2014
 [   32.464704] RIP: 0010:unregister_netdevice_many+0x72a/0x780
 [   32.464707] Code: 99 fd ff ff ba 90 1a 00 00 48 c7 c6 f4 02 66 96 48 c7 c7 20 4d 35 96 c6 05 fa c7 2b 02 01 e8 be 6f 4a 00 0f 0b e9 73 fd ff ff <0f> 0b e9 5f fd ff ff 80 3d e3 c7 2b 02 00 0f 85 3b fd ff ff ba 59
 [   32.464710] RSP: 0018:ffffa006422d7820 EFLAGS: 00010206
 [   32.464712] RAX: ffff8f6e077140a0 RBX: ffffa006422d7888 RCX: 0000000000000000
 [   32.464714] RDX: ffff8f6e12edbe58 RSI: 0000000000000296 RDI: ffffffff96d4a520
 [   32.464716] RBP: ffff8f6e07714000 R08: ffffffff96d63600 R09: ffffa006422d7728
 [   32.464717] R10: 0000000000000ec0 R11: ffffffff9698c988 R12: ffff8f6e12edb140
 [   32.464719] R13: dead000000000122 R14: dead000000000100 R15: ffff8f6e12edb140
 [   32.464723] FS:  00007f297c2f1740(0000) GS:ffff8f6e5d900000(0000) knlGS:0000000000000000
 [   32.464725] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 [   32.464726] CR2: 00007f297bf1c800 CR3: 00000000115e8000 CR4: 0000000000350ee0
 [   32.464730] Call Trace:
 [   32.464763]  <TASK>
 [   32.464767]  rtnl_dellink+0x13e/0x380
 [   32.464776]  ? cred_has_capability.isra.0+0x68/0x100
 [   32.464780]  ? __rtnl_unlock+0x33/0x60
 [   32.464783]  ? bpf_lsm_capset+0x10/0x10
 [   32.464786]  ? security_capable+0x36/0x50
 [   32.464790]  rtnetlink_rcv_msg+0x14e/0x3b0
 [   32.464792]  ? _copy_to_iter+0xb1/0x790
 [   32.464796]  ? post_alloc_hook+0xa0/0x160
 [   32.464799]  ? rtnl_calcit.isra.0+0x110/0x110
 [   32.464802]  netlink_rcv_skb+0x50/0xf0
 [   32.464806]  netlink_unicast+0x216/0x340
 [   32.464809]  netlink_sendmsg+0x23f/0x480
 [   32.464812]  sock_sendmsg+0x5e/0x60
 [   32.464815]  ____sys_sendmsg+0x22c/0x270
 [   32.464818]  ? import_iovec+0x17/0x20
 [   32.464821]  ? sendmsg_copy_msghdr+0x59/0x90
 [   32.464823]  ? do_set_pte+0xa0/0xe0
 [   32.464828]  ___sys_sendmsg+0x81/0xc0
 [   32.464832]  ? mod_objcg_state+0xc6/0x300
 [   32.464835]  ? refill_obj_stock+0xa9/0x160
 [   32.464838]  ? memcg_slab_free_hook+0x1a5/0x1f0
 [   32.464842]  __sys_sendmsg+0x49/0x80
 [   32.464847]  do_syscall_64+0x3b/0x90
 [   32.464851]  entry_SYSCALL_64_after_hwframe+0x44/0xae
 [   32.464865] RIP: 0033:0x7f297bf2e5e7
 [   32.464868] Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
 [   32.464869] RSP: 002b:00007ffd96c824c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 [   32.464872] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f297bf2e5e7
 [   32.464874] RDX: 0000000000000000 RSI: 00007ffd96c82540 RDI: 0000000000000003
 [   32.464875] RBP: 00000000640f19de R08: 0000000000000001 R09: 000000000000007c
 [   32.464876] R10: 00007f297bffabe0 R11: 0000000000000246 R12: 0000000000000001
 [   32.464877] R13: 00007ffd96c82d20 R14: 00007ffd96c82610 R15: 000055bfe38a7020
 [   32.464881]  </TASK>
 [   32.464882] ---[ end trace 0000000000000000 ]---

Fixes: 7d5cd2ce ("bonding: correctly handle bonding type change on enslave failure")
Reported-by: syzbot+9dfc3f3348729cc82277@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3efSigned-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add bond_ether_setup helper which is used to fix ether_setup() calls in the
bonding driver. It takes care of both IFF_MASTER and IFF_SLAVE flags, the
former is always restored and the latter only if it was set.
If the bond enslaves non-ARPHRD_ETHER device (changes its type), then
releases it and enslaves ARPHRD_ETHER device (changes back) then we
use ether_setup() to restore the bond device type but it also resets its
flags and removes IFF_MASTER and IFF_SLAVE[1]. Use the bond_ether_setup
helper to restore both after such transition.

[1] reproduce (nlmon is non-ARPHRD_ETHER):
 $ ip l add nlmon0 type nlmon
 $ ip l add bond2 type bond mode active-backup
 $ ip l set nlmon0 master bond2
 $ ip l set nlmon0 nomaster
 $ ip l add bond1 type bond
 (we use bond1 as ARPHRD_ETHER device to restore bond2's mode)
 $ ip l set bond1 master bond2
 $ ip l sh dev bond2
 37: bond2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether be:d7:c5:40:5b:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500
 (notice bond2's IFF_MASTER is missing)

Fixes: e36b9d16 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yoshihiro Shimoda says:

====================
net: renesas: rswitch: Fix rx and timestamp

I got reports locally about issues on the rswitch driver.
So, fix the issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>