This revises and enhances the bnx2x register dump facilities,
adding support for `ethtool -w' on top of `ethtool -d'.
Signed-off-by: Miriam Shitrit <miris@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On rare occasions, self test link may fail since the link is
being sampled while it's still being stabilized.
To correct this behaviour, try to sample the link for 2 seconds
prior to declaring a failure.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current logic causes chips running in switch dependent multi-function
FCoE mode not to configure their MAC, leading to an all 0s MAC.

This patch configures the interface with the SAN Mac instead.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Self-tests following boot from SAN have failed as the
UNDI driver might leave some NIG interrupt indications.

This patch does the clean-up, clearing those indications
and allowing the test to pass.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	Documentation/networking/ip-sysctl.txt
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c

Both conflicts were simply overlapping context.

A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>

TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit a5e371f6 ("drivers/net: delete
all code/drivers depending on CONFIG_MCA") most of the MCA drivers went,
including the Kconfig/Makefile hooks for ibmlana, but it seems that I
missed the "git rm" on these actual driver files, and with the namespace
overlap with machine check architecture, it got missed by various git
grep type checking done at that time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains netfilter fixes for 3.8-rc3,
they are:

* fix possible BUG_ON if several netns are in use and the nf_conntrack
  module is removed, initial patch from Gao feng, final patch from myself.

* fix unset return value if conntrack zone are disabled at
  compile-time, reported by Borislav Petkov, fix from myself.

* fix display error message via dmesg for arp_tables, from Jan Engelhardt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset.  The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open).  For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.

We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device.  In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.

The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls.  This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation.  On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Tested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new permission to align with the new TUN multiqueue support,
"tun_socket:attach_queue".

The corresponding SELinux reference policy patch is show below:

 diff --git a/policy/flask/access_vectors b/policy/flask/access_vectors
 index 28802c5..a0664a1 100644
 --- a/policy/flask/access_vectors
 +++ b/policy/flask/access_vectors
 @@ -827,6 +827,9 @@ class kernel_service

  class tun_socket
  inherits socket
 +{
 +       attach_queue
 +}

  class x_pointer
  inherits x_device
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Tested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

spin_is_locked() on a non !SMP build is kind of useless.

BUG_ON(!spin_is_locked(xx)) is guaranteed to crash.

Just remove this check in reqsk_fastopen_remove() as
the callers do hold the socket lock.
Reported-by: Ketan Kulkarni <ketkulka@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Dave Taht <dave.taht@gmail.com>
Acked-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull devicetree fixes from Rob Herring:
 "Two fixes to prevent unconditional re-compile of dts files on arm and
  arm64."

* tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
  ARM: dts: prevent *.dtb from always being rebuilt
  arm64: dts: prevent *.dtb from always being rebuilt

Andrew Morton pointed this out a month ago, and then I completely forgot
about it.

If we read a partial last page of a block device, we will zero out the
end of the page, but since that page can then be mapped into user space,
we should also make sure to flush the cache on architectures that have
virtual caches.  We have the flush_dcache_page() function for this, so
use it.

Now, in practice this really never matters, because nobody sane uses
virtual caches to begin with, and they largely exist on old broken RISC
arhitectures.

And even if you did run on one of those obsolete CPU's, the whole "mmap
and access the last partial page of a block device" behavior probably
doesn't actually exist.  The normal IO functions (read/write) will never
see the zeroed-out part of the page that migth not be coherent in the
cache, because they honor the size of the device.

So I'm marking this for stable (3.7 only), but I'm not sure anybody will
ever care.
Pointed-out-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org  # 3.7
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ifb should lookup devices in the appropriate namespace.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet pointed out that act_mirred needs to find the current net_ns,
and struct net pointer is not provided in the call chain.  His original
patch made use of current->nsproxy->net_ns to find the network namespace,
but this fails to work correctly for userspace code that makes use of
netlink sockets in different network namespaces.  Instead, pass the
"struct net *" down along the call chain to where it is needed.

This version removes the ifb changes as Eric has submitted that patch
separately, but is otherwise identical to the previous version.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only user is cxgb3 driver.

old_neigh is used to check device change, but it must not happen
on redirect.  In this sense, we can remove old_neigh argument.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull sound fixes from Takashi Iwai:
 "Most of commits found here are for ASoC device specific fixes,
  arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
  memory leak fixes in ASoC core.

  Other than that, regression fixes in HD-audio and USB-audio, and a fix
  for new Realtek codecs."

* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
  ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
  ALSA: hda - Add support of new codec ALC284
  ALSA: usb-audio: Make ebox44_table static
  ALSA: hdspm - Fix wordclock status on AES32
  Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
  ALSA: hda - Disable runtime D3 for Intel CPT & co
  ALSA: pxa27x: fix ac97 warm reset
  ALSA: pxa27x: fix ac97 cold reset
  ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
  ASoC: wm2000: Fix sense of speech clarity enable
  ASoC: wm5100: Remove DSP B and left justified formats
  ASoC: arizona: Remove DSP B and left justified AIF modes
  ASoC: wm2200: Remove DSP B and left justified AIF modes
  ASoC: wm5102: Improve speaker enable performance
  ASoC: core: fix the memory leak in case of remove_aux_dev()
  ASoC: core: fix the memory leak in case of device_add() failure
  ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
  ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
  ASoC: lm49453: Fix adc, mic and sidetone volume ranges
  ASoC: arizona: Correct FLL source definitions
  ...

The removal of the 8390 EISA drivers actually comprises the
complete content of the EISA probe block, so we can now remove
that block, and its hook into the unified probe.  Note that
the deleted comment mentions PCI probes, but they long since
moved elsewhere, so no PCI probes are touched here.

We get rid of the orphaned EISA probe prototypes, and a couple
of left over MCA probe prototypes at the same time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_prefix_equal() just casts its arguments and it is the only
user of __ipv6_prefix_equal().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce __ipv6_addr_diff64() to to find the first different
bit between two addresses on 64bit architectures.

32bit version is still available as __ipv6_addr_diff32(),
and __ipv6_addr_diff() automatically selects appropriate
version.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull staging fixes from Greg Kroah-Hartman:
 "Here are a number of small fixes to staging drivers for your 3.8-rc3
  tree.

  Well, the omapdrm fixes aren't really "small" but they were waiting on
  a number of other drm patches to go in through the drm tree, and got
  delayed by my vacation over the holidays.  They are totally
  self-contained, everyone involved have acked them, and they fix issues
  that people have been having with the driver.

  Other than that one, it's a bunch of tiny bugfixes for a number of
  reported issues.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (36 commits)
  staging: zram: fix invalid memory references during disk write
  staging: tidspbridge: use prepare/unprepare on dsp clocks
  staging: tidspbridge: Fix build breakage due to splitting CM functions.
  staging: comedi: comedi_test: fix race when cancelling command
  staging: comedi: Kconfig: COMEDI_NI_AT_A2150 should select COMEDI_FC
  staging: comedi: prevent auto-unconfig of manually configured devices
  staging: comedi: fix minimum AO period for NI 625x and NI 628x
  staging: vme_pio2: fix oops on module unloading
  staging: speakup: avoid out-of-range access in synth_add()
  staging: speakup: avoid out-of-range access in synth_init()
  staging: rtl8192e: Fix failure to check pci_map_single()
  staging: rtl8187se: Fix failure to check pci_map_single()
  staging: drm/imx: fix double free bug in error path
  staging: drm/imx: several bug fixes
  staging: drm/imx: check return value of ipu_reset()
  staging: drm/omap: fix flags in dma buf exporting
  staging: drm/omap: use omapdss low level API
  staging/fwserial: Update TODO file per reviewer comments
  staging/fwserial: Limit tx/rx to 1394-2008 spec maximum
  staging/fwserial: Refine Kconfig help text
  ...

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a bunch of USB fixes for your 3.8-rc3 tree.  They all either
  fix problems that have been reported (like the xhci/hub changes) or
  add new device ids to existing drivers.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
  usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
  usb: host: ohci-tmio: fix compile warning
  USB: Add device quirk for Microsoft VX700 webcam
  USB: ehci-fsl: fix regression on mpc5121e
  usb: chipidea: Allow disabling streaming not only in udc mode
  USB: fsl-mph-dr-of: fix regression on mpc5121e
  USB: select USB_ARCH_HAS_EHCI for MXS
  USB: hub: handle claim of enabled remote wakeup after reset
  USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
  USB: option: add Nexpring NP10T terminal id
  USB: option: add Telekom Speedstick LTE II
  USB: option: blacklist network interface on ZTE MF880
  usb: imx21-hcd: Include missing linux/module.h
  USB: option: Add new MEDIATEK PID support
  USB: ehci: make debug port in-use detection functional again
  USB: usbtest: fix test number in log message
  xhci: Avoid "dead ports", add roothub port polling.
  USB: Handle warm reset failure on empty port.
  USB: Ignore port state until reset completes.
  USB: Increase reset timeout.
  ...

Pull driver core fixes from Greg Kroah-Hartman:
 "Here are two patches for 3.8-rc3.

  One removes the __dev* defines from init.h now that all usages of it
  are gone from your tree.  The other fix is for debugfs's paramater
  that was using the wrong base for the option.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  debugfs: convert gid= argument from decimal, not octal
  Remove __dev* markings from init.h

Pull char/misc fix from Greg Kroah-Hartman:
 "Here is a single fix for the mei driver that resolves a reported
  issue.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'char-misc-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: fix mismatch in mutex unlock-lock in mei_amthif_read()

Pull drm fixes from Dave Airlie:
 "Nothing too astounding

   - nouveau: bunch of regression fixes and oops fixes
   - radeon: UMS fixes, rn50 fix, dma fix
   - udl: fix EDID retrieval for large EDIDs."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  udldrmfb: udl_get_edid: drop unneeded i--
  udldrmfb: udl_get_edid: usb_control_msg buffer must not be on the stack
  udldrmfb: Fix EDID not working with monitors with EDID extension blocks
  drm/nvc0/fb: fix crash when different mutex is used to protect same list
  drm/nouveau/clock: fix support for more than 2 monitors on nve0
  drm/nv50/disp: fix selection of bios script for analog outputs
  drm/nv17-50: restore fence buffer on resume
  drm/nouveau: fix blank LVDS screen regression on pre-nv50 cards
  drm/nouveau: fix nouveau_client allocation failure path
  drm/nouveau: don't return freed object from nouveau_handle_create
  drm/nouveau/vm: fix memory corruption when pgt allocation fails
  drm/nouveau: add locking around instobj list operations
  drm/nouveau: do not forcibly power on lvds panels
  drm/nouveau/devinit: ensure legacy vga control is enabled during post
  radeon/kms: fix dma relocation checking
  radeon/kms: force rn50 chip to always report connected on analog output
  drm/radeon: fix error path in kpage allocation
  drm/radeon: fix a bogus kfree
  drm/radeon: fix NULL pointer dereference in UMS mode

Pull networking fixes from David Miller:

 1) Fix regression allowing IP_TTL setting of zero, fix from Cong Wang.

 2) Fix leak regressions in tunap, from Jason Wang.

 3) be2net driver always returns IRQ_HANDLED in INTx handler, fix from
    Sathya Perla.

 4) qlge doesn't really support NETIF_F_TSO6, don't set that flag.  Fix
    from Amerigo Wang.

 5) Add 802.11ad Atheros wil6210 driver, from Vladimir Kondratiev.

 6) Fix MTU calculations in mac80211 layer, from T Krishna Chaitanya.

 7) Station info layer of mac80211 needs to use del_timer_sync(), from
    Johannes Berg.

 8) tcp_read_sock() can loop forever, because we don't immediately stop
    when recv_actor() returns zero.  Fix from Eric Dumazet.

 9) Fix WARN_ON() in tcp_cleanup_rbuf().  We have to use sk_eat_skb() in
    tcp_recv_skb() to handle the case where a large GRO packet is split
    up while it is use by a splice() operation.  Fix also from Eric
    Dumazet.

10) addrconf_get_prefix_route() in ipv6 tests flags incorrectly, it
    does:

        if (X && (p->flags & Y) != 0)

    when it really meant to go:

        if (X && (p->flags & X) != 0)

    fix from Romain Kuntz.

11) Fix lost Kconfig dependency for bfin_mac driver hardware
    timestamping.  From Lars-Peter Clausen.

12) Fix regression in handling of RST without ACK in TCP, from Eric
    Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  be2net: fix unconditionally returning IRQ_HANDLED in INTx
  tuntap: fix leaking reference count
  tuntap: forbid calling TUNSETIFF when detached
  tuntap: switch to use rtnl_dereference()
  net, wireless: overwrite default_ethtool_ops
  qlge: remove NETIF_F_TSO6 flag
  tcp: accept RST without ACK flag
  net: ethernet: xilinx: Do not use NO_IRQ in axienet
  net: ethernet: xilinx: Do not use axienet on PPC
  bnx2x: Allow management traffic after boot from SAN
  bnx2x: Fix fastpath structures when memory allocation fails
  bfin_mac: Restore hardware time-stamping dependency on BF518
  tun: avoid owner checks on IFF_ATTACH_QUEUE
  bnx2x: move debugging code before the return
  tuntap: refuse to re-attach to different tun_struct
  ipv6: use addrconf_get_prefix_route for prefix route lookup [v2]
  ipv6: fix the noflags test in addrconf_get_prefix_route
  tcp: fix splice() and tcp collapsing interaction
  tcp: splice: fix an infinite loop in tcp_read_sock()
  net: prevent setting ttl=0 via IP_TTL
  ...

Pull sparc updates from David Miller:

 1) Add finit_module syscall entry.

 2) Remove stray __dev{init,exit} references, from Sam Ravnborg.

Fix up conflicts in the sparc PCI code due to whitespace differences in
the __dev{init,exit} removal (which also came in through Greg).

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: remove __devinit, __devexit annotations
  sparc: Hook up finit_module syscall.

if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt.

This fixes a regression introduced by the .dtb rule rework in 499cd829
"ARM: dt: change .dtb build rules to build in dts directory".
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt. Note

This fixes a regression introduced by the .dtb rule rework in da4cbc6
"arm64: use new common dtc rule", although since arm64 doesn't actually
have any *.dts yet, this isn't a critical issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Fixes a bug introduced by commit c8f2f0db ("zram: Fix handling
of incompressible pages") which caused invalid memory references
during disk write. Invalid references could occur in two cases:
 - Incoming data expands on compression: In this case, reference was
made to kunmap()'ed bio page.
 - Partial (non PAGE_SIZE) write with incompressible data: In this
case, reference was made to a kfree()'ed buffer.

Fixes bug 50081:
https://bugzilla.kernel.org/show_bug.cgi?id=50081Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Mihail Kasadjikov <hamer.mk@gmail.com>
Reported-by: Tomas M <tomas@slax.org>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IN6ADDR_* and in6addr_* are not exported to userspace, and are defined
in include/linux/in6.h.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- use per_cpu_add when possible
- prevent the TT component to add multicast address as "mesh clients"
- some debug output improvements
- proper lockdeps class initializations
- new style fixes (space before/after brackets)
- other minor fixes and refactoring
Signed-off-by: David S. Miller <davem@davemloft.net>