[ Upstream commit 59c816c1 ]

This code in vhost_scsi_make_tpg() is confusing because we limit "tpgt"
to UINT_MAX but the data type of "tpg->tport_tpgt" and that is a u16.

I looked at the context and it turns out that in
vhost_scsi_set_endpoint(), "tpg->tport_tpgt" is used as an offset into
the vs_tpg[] array which has VHOST_SCSI_MAX_TARGET (256) elements so
anything higher than 255 then it is invalid.  I have made that the limit
now.

In vhost_scsi_send_evt() we mask away values higher than 255, but now
that the limit has changed, we don't need the mask.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit be32c0cf ]

The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 96a5d18b ]

The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).

Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.

See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit b8a9d66d ]

After commit 566c09c5 ("raid5: relieve lock contention in get_active_stripe()")
__find_stripe() is called under conf->hash_locks + hash.
But handle_stripe_clean_event() calls remove_hash() under
conf->device_lock.

Under some cirscumstances the hash chain can be circuited,
and we get an infinite loop with disabled interrupts and locked hash
lock in __find_stripe(). This leads to hard lockup on multiple CPUs
and following system crash.

I was able to reproduce this behavior on raid6 over 6 ssd disks.
The devices_handle_discard_safely option should be set to enable trim
support. The following script was used:

for i in `seq 1 32`; do
    dd if=/dev/zero of=large$i bs=10M count=100 &
done

neilb: original was against a 3.x kernel.  I forward-ported
  to 4.3-rc.  This verison is suitable for any kernel since
  Commit: 59fc630b ("RAID5: batch adjacent full stripe write")
  (v4.1+).  I'll post a version for earlier kernels to stable.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Fixes: 566c09c5 ("raid5: relieve lock contention in get_active_stripe()")
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org> # 3.13 - 4.2
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 0ca81a28 ]

ib_send_cm_sidr_rep could sometimes erase the node from the sidr
(depending on errors in the process). Since ib_send_cm_sidr_rep is
called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv
could be either erased from the rb_tree twice or not erased at all.
Fixing that by making sure it's erased only once before freeing
cm_id_priv.

Fixes: a977049d ('[PATCH] IB: Add the kernel CM implementation')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 22805217 ]

When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays
NULL but it's later used in mvs_abort_task as slot which is passed
to mvs_slot_task_free causing NULL pointer dereference.

Just return from mvs_slot_task_free when passed with NULL slot.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit d01552a7 ]

This reverts commit 7eb41885.

This commit is poorly justified, I can find not discusison in email,
and it clearly causes a problem.

If a device which is being recovered fails and is subsequently
re-added to an array, there could easily have been changes to the
array *before* the point where the recovery was up to.  So the
recovery must start again from the beginning.

If a spare is being recovered and fails, then when it is re-added we
really should do a bitmap-based recovery up to the recovery-offset,
and then a full recovery from there.  Before this reversion, we only
did the "full recovery from there" which is not corect.  After this
reversion with will do a full recovery from the start, which is safer
but not ideal.

It will be left to a future patch to arrange the two different styles
of recovery.
Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: stable@vger.kernel.org (3.14+)
Fixes: 7eb41885 ("md: allow a partially recovered device to be hot-added to an array.")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 681ab469 ]

This was introduced with 9e882242
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.

Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 203d27b0 ]

This was introduced with 9e882242
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.

Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3fc89adb ]

Currently a number of Crypto API operations may fail when a signal
occurs.  This causes nasty problems as the caller of those operations
are often not in a good position to restart the operation.

In fact there is currently no need for those operations to be
interrupted by user signals at all.  All we need is for them to
be killable.

This patch replaces the relevant calls of signal_pending with
fatal_signal_pending, and wait_for_completion_interruptible with
wait_for_completion_killable, respectively.

Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 275d7d44 ]

Poma (on the way to another bug) reported an assertion triggering:

  [<ffffffff81150529>] module_assert_mutex_or_preempt+0x49/0x90
  [<ffffffff81150822>] __module_address+0x32/0x150
  [<ffffffff81150956>] __module_text_address+0x16/0x70
  [<ffffffff81150f19>] symbol_put_addr+0x29/0x40
  [<ffffffffa04b77ad>] dvb_frontend_detach+0x7d/0x90 [dvb_core]

Laura Abbott <labbott@redhat.com> produced a patch which lead us to
inspect symbol_put_addr(). This function has a comment claiming it
doesn't need to disable preemption around the module lookup
because it holds a reference to the module it wants to find, which
therefore cannot go away.

This is wrong (and a false optimization too, preempt_disable() is really
rather cheap, and I doubt any of this is on uber critical paths,
otherwise it would've retained a pointer to the actual module anyway and
avoided the second lookup).

While its true that the module cannot go away while we hold a reference
on it, the data structure we do the lookup in very much _CAN_ change
while we do the lookup. Therefore fix the comment and add the
required preempt_disable().
Reported-by: poma <pomidorabelisima@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fixes: a6e6abd5 ("module: remove module_text_address()")
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit a54c8f0f ]

xen-blkfront will crash if the check to talk_to_blkback()
in blkback_changed()(XenbusStateInitWait) returns an error.
The driver data is freed and info is set to NULL. Later during
the close process via talk_to_blkback's call to xenbus_dev_fatal()
the null pointer is passed to and dereference in blkfront_closing.

CC: stable@vger.kernel.org
Signed-off-by: Cathy Avery <cathy.avery@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit fd7cd061 ]

We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.

Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:

commit 638298dc ("xhci: Fix spurious wakeups after S5 on Haswell")

It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914 ("xhci: Limit the spurious wakeup fix only to HP machines")

Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.

commit b45abacd ("xhci: no switching back on non-ULT Haswell")

Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3b4739b8 ]

If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.

Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 4dcb8b57 ]

btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.

Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 2871c69e ]

Commit 4c7e3093 ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().

The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them.  If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.

Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.

Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.cSigned-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 9702970c ]

This reverts commit e306dfd0.

With this patch applied, we were the only architecture making this sort
of adjustment to the PC calculation in the unwinder. This causes
problems for ftrace, where the PC values are matched against the
contents of the stack frames in the callchain and fail to match any
records after the address adjustment.

Whilst there has been some effort to change ftrace to workaround this,
those patches are not yet ready for mainline and, since we're the odd
architecture in this regard, let's just step in line with other
architectures (like arch/arm/) for now.

Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit bae818ee ]

rbd requires stable pages, as it performs a crc of the page data before
they are send to the OSDs.

But since kernel 3.9 (patch 1d1d1a76
"mm: only enforce stable page writes if the backing device requires
it") it is not assumed anymore that block devices require stable pages.

This patch sets the necessary flag to get stable pages back for rbd.

In a ceph installation that provides multiple ext4 formatted rbd
devices "bad crc" messages appeared regularly (ca 1 message every 1-2
minutes on every OSD that provided the data for the rbd) in the
OSD-logs before this patch. After this patch this messages are pretty
much gone (only ca 1-2 / month / OSD).

Cc: stable@vger.kernel.org # 3.9+, needs backporting
Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de>
[idryomov@gmail.com: require stable pages only in crc case, changelog]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit b94e2280 ]

0° Kelvin is actually −273.15°C, not -272.15°C. Fix the temperature offset.
Also improve the comment explaining the calculation.
Reported-by: Janusz Użycki <j.uzycki@elpromaelectronics.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 49abb266 ]

Fixes a harmless error message caused by:
51a4726bSigned-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8e7a65aa ]

We accidentally lost the initial DPLL register write in
1c4e0274 drm/i915: Fix DVO 2x clock enable on 830M

The "three times for luck" hack probably saved us from a total
disaster. But anyway, bring the initial write back so that the
code actually makes some sense.
Reported-and-tested-by: Nick Bowler <nbowler@draconx.ca>
References: http://mid.gmane.org/CAN_QmVyMaArxYgEcVVsGvsMo7-6ohZr8HmF5VhkkL4i9KOmrhw@mail.gmail.com
Cc: stable@vger.kernel.org
Cc: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 2a6c521b ]

On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.

This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 31f50e48 ]

This patch fixes following build warning:

In file included from include/linux/printk.h:261:0,
                 from include/linux/kernel.h:13,
                 from include/linux/list.h:8,
                 from include/linux/module.h:9,
                 from drivers/power/bq24190_charger.c:11:
drivers/power/bq24190_charger.c: In function ‘bq24190_irq_handler_thread’:
include/linux/dynamic_debug.h:86:20: warning: ‘ss_reg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   __dynamic_dev_dbg(&descriptor, dev, fmt, \
                    ^
drivers/power/bq24190_charger.c:1211:5: note: ‘ss_reg’ was declared here
  u8 ss_reg, f_reg;
     ^
In file included from include/linux/printk.h:261:0,
                 from include/linux/kernel.h:13,
                 from include/linux/list.h:8,
                 from include/linux/module.h:9,
                 from drivers/power/bq24190_charger.c:11:
include/linux/dynamic_debug.h:86:20: warning: ‘f_reg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   __dynamic_dev_dbg(&descriptor, dev, fmt, \
                    ^
drivers/power/bq24190_charger.c:1211:13: note: ‘f_reg’ was declared here
  u8 ss_reg, f_reg;
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 1d20a160 ]

drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]

This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'.  Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 296291cd ]

Currently a simple program below issues a sendfile(2) system call which
takes about 62 days to complete in my test KVM instance.

        int fd;
        off_t off = 0;

        fd = open("file", O_RDWR | O_TRUNC | O_SYNC | O_CREAT, 0644);
        ftruncate(fd, 2);
        lseek(fd, 0, SEEK_END);
        sendfile(fd, fd, &off, 0xfffffff);

Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.

We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.

Fix the problem by doing the signal check before writing anything.  That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: Jan Kara <jack@suse.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 97aff2c0 ]

There are 24 EQ registers not 25, I suspect this bug came about because
the registers start at EQ1 not zero. The bug is relatively harmless as
the extra register written is an unused one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 8832317f ]

Currently we do not validate rtas.entry before calling enter_rtas(). This
leads to a kernel oops when user space calls rtas system call on a powernv
platform (see below). This patch adds code to validate rtas.entry before
making enter_rtas() call.

  Oops: Exception in kernel mode, sig: 4 [#1]
  SMP NR_CPUS=1024 NUMA PowerNV
  task: c000000004294b80 ti: c0000007e1a78000 task.ti: c0000007e1a78000
  NIP: 0000000000000000 LR: 0000000000009c14 CTR: c000000000423140
  REGS: c0000007e1a7b920 TRAP: 0e40   Not tainted  (3.18.17-340.el7_1.pkvm3_1_0.2400.1.ppc64le)
  MSR: 1000000000081000 <HV,ME>  CR: 00000000  XER: 00000000
  CFAR: c000000000009c0c SOFTE: 0
  NIP [0000000000000000]           (null)
  LR [0000000000009c14] 0x9c14
  Call Trace:
  [c0000007e1a7bba0] [c00000000041a7f4] avc_has_perm_noaudit+0x54/0x110 (unreliable)
  [c0000007e1a7bd80] [c00000000002ddc0] ppc_rtas+0x150/0x2d0
  [c0000007e1a7be30] [c000000000009358] syscall_exit+0x0/0x98

Cc: stable@vger.kernel.org # v3.2+
Fixes: 55190f88 ("powerpc: Add skeleton PowerNV platform")
Reported-by: NAGESWARA R. SASTRY <nasastry@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Reword change log, trim oops, and add stable + fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit cbf3ccd0 ]

During device assignment/deassignment the flags in the DTE
get lost, which might cause spurious faults, for example
when the device tries to access the system management range.
Fix this by not clearing the flags with the rest of the DTE.
Reported-by: G. Richard Bellamy <rbellamy@pteradigm.com>
Tested-by: G. Richard Bellamy <rbellamy@pteradigm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f08f6258 ]

Add 3 new subdevice IDs for the 0x095A device ID and 2 for the 0x095B
device ID.

Cc: <stable@vger.kernerl.org> [3.13+]
Reported-by: Jeremy <jeremy.bomkamp@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 2cf5eb3a ]

The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.

Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3fd0d3c1 ]

Identify 7265-D devices using the hardware revision (they have the
same PCI IDs as 7265) and change the configuration for them taking
the differences (currently only the firmware image) into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit b5a48134 ]

The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.

Cc: <stable@vger.kernel.org> [3.8+]
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 5bd16687 ]

The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.

Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 029cd037 ]

ath9k inserts padding between the 802.11 header and the data area (to
align it). Since it didn't declare this extra required headroom, this
led to some nasty issues like randomly dropped packets in some setups.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 886d3dfa ]

The comment helpfully explains why hardirq.h is included, but since
commit 2d4b8473 ("hardirq: Split preempt count mask definitions")
in_interrupt() has been provided by preempt_mask.h.  Use that instead,
saving around 40 lines in the generated dependency file.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 3ebe138a ]

If rbd_dev_image_probe() in rbd_dev_probe_parent() fails, header_name
is freed twice: once in rbd_dev_probe_parent() and then in its caller
rbd_dev_image_probe() (rbd_dev_image_probe() is called recursively to
handle parent images).

rbd_dev_probe_parent() is responsible for probing the parent, so it
shouldn't muck with clone's fields.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit ba30670f ]

Fixes: ac8c3f3d ("dm thin: generate event when metadata threshold passed")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 51a4726b ]

They were added relatively early in the driver init process
which meant that in some cases the driver was not finished
initializing before external tools tried to use them which
could result in a crash depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit f231976c ]

We need to do this in order to prevent accesses to the device while it's
powered down.  Userspace may have an mmap of the fb, and there's no good
way (that I know of) to prevent it from touching the device otherwise.

This fixes some nasty races between runpm and plymouth on some systems,
which result in the GPU getting very upset and hanging the boot.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 874bbfe6 ]

My system keeps crashing with below message. vmstat_update() schedules a delayed
work in current cpu and expects the work runs in the cpu.
schedule_delayed_work() is expected to make delayed work run in local cpu. The
problem is timer can be migrated with NO_HZ. __queue_work() queues work in
timer handler, which could run in a different cpu other than where the delayed
work is scheduled. The end result is the delayed work runs in different cpu.
The patch makes __queue_delayed_work records local cpu earlier. Where the timer
runs doesn't change where the work runs with the change.

[   28.010131] ------------[ cut here ]------------
[   28.010609] kernel BUG at ../mm/vmstat.c:1392!
[   28.011099] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN
[   28.011860] Modules linked in:
[   28.012245] CPU: 0 PID: 289 Comm: kworker/0:3 Tainted: G        W4.3.0-rc3+ #634
[   28.013065] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153802- 04/01/2014
[   28.014160] Workqueue: events vmstat_update
[   28.014571] task: ffff880117682580 ti: ffff8800ba428000 task.ti: ffff8800ba428000
[   28.015445] RIP: 0010:[<ffffffff8115f921>]  [<ffffffff8115f921>]vmstat_update+0x31/0x80
[   28.016282] RSP: 0018:ffff8800ba42fd80  EFLAGS: 00010297
[   28.016812] RAX: 0000000000000000 RBX: ffff88011a858dc0 RCX:0000000000000000
[   28.017585] RDX: ffff880117682580 RSI: ffffffff81f14d8c RDI:ffffffff81f4df8d
[   28.018366] RBP: ffff8800ba42fd90 R08: 0000000000000001 R09:0000000000000000
[   28.019169] R10: 0000000000000000 R11: 0000000000000121 R12:ffff8800baa9f640
[   28.019947] R13: ffff88011a81e340 R14: ffff88011a823700 R15:0000000000000000
[   28.020071] FS:  0000000000000000(0000) GS:ffff88011a800000(0000)knlGS:0000000000000000
[   28.020071] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   28.020071] CR2: 00007ff6144b01d0 CR3: 00000000b8e93000 CR4:00000000000006f0
[   28.020071] Stack:
[   28.020071]  ffff88011a858dc0 ffff8800baa9f640 ffff8800ba42fe00ffffffff8106bd88
[   28.020071]  ffffffff8106bd0b 0000000000000096 0000000000000000ffffffff82f9b1e8
[   28.020071]  ffffffff829f0b10 0000000000000000 ffffffff81f18460ffff88011a81e340
[   28.020071] Call Trace:
[   28.020071]  [<ffffffff8106bd88>] process_one_work+0x1c8/0x540
[   28.020071]  [<ffffffff8106bd0b>] ? process_one_work+0x14b/0x540
[   28.020071]  [<ffffffff8106c214>] worker_thread+0x114/0x460
[   28.020071]  [<ffffffff8106c100>] ? process_one_work+0x540/0x540
[   28.020071]  [<ffffffff81071bf8>] kthread+0xf8/0x110
[   28.020071]  [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200
[   28.020071]  [<ffffffff81a6522f>] ret_from_fork+0x3f/0x70
[   28.020071]  [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v2.6.31+
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>