Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch attempts to ensure that ath9k's built-in rate control algorithm
does not rely on the value of the ampdu_len and ampdu_ack_len tx status
fields unless the IEEE80211_TX_STAT_AMPDU flag is set.

This patch has not been tested.

Cc: <stable@kernel.org>
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the following problems with the rate control feedback
generated by ath9k for A-MPDU frames:

1. Rate control feedback is carried on the first frame of an aggregate
that is either ACKed, or has execeeded the software retry count and is
considered failed. However, ath9k would incorrectly assume the aggregate
had the length 1 if one of these conditions did not apply to the first
frame of the aggregate, but instead a later frame. This fix therefor
copies the bf_nframes field of the buffer in the same manner as the rates
field of the tx status.

2. Sometimes the ampdu_len and ampdu_ack_len fields of the tx status was
left uninitialized eventhough the IEEE80211_TX_STAT_AMPDU flag was set.
This is now avoid by setting flag and fields in the same place.

3. Even if a frame has been selected for aggregation by mac80211 and
marked with the IEEE80211_TX_CTL_AMPDU flag it can sometimes happen that
ath9k transmits the frame without aggregation. In these cases the
ampdu_ack_len field could be incorrectly computed because the nbad
parameter to ath_tx_rc_status was incorrect.

Cc: <stable@kernel.org>
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes two problems with the minstrel_ht rate control
algorithms handling of A-MPDU frames:

1. The ampdu_len field of the tx status is not always initialized for
non-HT frames (and it would probably be unreasonable to require all
drivers to do so). This could cause rate control statistics to be
corrupted. We now trust the ampdu_len and ampdu_ack_len fields only when
the frame is marked with the IEEE80211_TX_STAT_AMPDU flag.

2. Successful transmission attempts where only recognized when the A-MPDU
subframe carrying the rate control status information was marked with the
IEEE80211_TX_STAT_ACK flag. If this information happed to be carried on a
frame that failed to be ACKed then the other subframes (which may have
succeeded) where not correctly registered. We now update rate control
statistics regardless of whether the subframe carrying the information was
ACKed or not.

Cc: <stable@kernel.org>
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since this small buffer isn't used for DMA,
we can simply allocate it on the stack, it
just needs to be 16 bytes of which only 8
will be used for WEP40 keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251 is grown up now and can have its own room^H^H^H^Hdirectory.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1271 driver is under heavy development but on the other hand the older
wl1251 driver is currently considered more as a legacy driver. To make it
easier to develop wl1271 features move wl1251 to it's own directory,
drivers/net/wireless/wl1251.

There are no functional changes, only moving of files. One regression
is that Kconfig won't be updated automatically and user needs to enable
wl1251 manually with an older config file.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In preparation of moving wl1251 out from drivers/net/wireless/wl12xx
create a separate copy of wl12xx_80211.h.

This file should not even exist, we should instead use generic ieee80211
definitions. This will be fixed in the future so that the file can
be removed.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the past, carl9170 has been plagued by mysterious
ghosts.

e.g.:
 wlan4: deauthenticated from 02:04:d8:3c:ac:c1 (Reason: 0)

Apparently, the AP sent us a bogus deauthentication
notification. But upon closer inspection the
"management frame" turned out to be a corrupted
scrap of an unsuccessful A-MPDU.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The total/fatal error bit was erroneously prefixed
with AR9170_RX_ERROR instead of AR9170_RX_STATUS.
Luckily, the hardware specification confirmed that
the 0x80 flag will never be set for mac->error.
So, it was always just a dead branch.

This patch also imports the latest version of
shared wlan.h header from the firmware git.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch replaces several identical frame drop
paths with a single shared rx frame error handler.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patches "rt2x00: Improve TX status entry validation" and "rt2x00: rework tx
status handling in rt2800pci" together were causing problems with tx status
processing in rt2800pci:

phy1 -> rt2800pci_txdone: Warning - Got TX status for an empty queue 3, dropping
phy1 -> rt2800pci_txdone: Warning - Got TX status for an unavailable queue 7, dropping

Fix this by using the correct field definition for getting the QID out of the
tx status report.
Reported-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is no need to initialize qidx to zero as it will ever be
overwritten by the correct value.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is an error condition that is not supposed to happen. Hence, it is
safe to add unlikely to this check.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since no skb will be mapped for RX and TX at the same time we can
simply shortcut the check for SKBDESC_DMA_MAPPED_TX.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates IEEE802.11 mesh constants to be consistent with newly
approved values. It modifies some values, as well as adds many new constants
in preparation for updating mesh code to the current 802.11s drafts. ANA
numbers were taken from:
https://mentor.ieee.org/802.11/dcn/09/11-09-0031-12-0000-ana-database-assigned-number-authority.xls

A few notes are in order:
1. This will break backwards compatibility with existing Linux kernels as
over-the-air constants have changed.
2. Some old and obsolete constants have been retained for now as the mesh code
itself hasn't been updated yet to the new 802.11s draft. This was desired to
keep the existing mesh scheme working until it can be updated. Adding the
approved values is the first step in updating the mesh code.
3. Obsolete constants have been clearly marked.
4. All ANA approved 802.11s constants have been added.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Results for the active channel are updated whenever a new survey dump
is requested, the old data is kept to allow multiple processes to
make their own channel utilization averages.
All other channels only contain the data for the last time that the
hardware was on the channel, i.e. the last scan result or other
off-channel activity.
Running a background scan does not clear the data for the active
channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This prevents random memory corruption if the number of channels ever gets
changed without an update to the internal channel array size.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using these, user space can calculate a relative channel utilization
with arbitrary intervals by regularly taking snapshots of the survey
results.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Several serve threading problems in the current
release reorder timer implementation have been
discovered.

A lengthy discussion - which lists some of the
pitfalls and possible solutions - can be found at:
 http://marc.info/?t=128635927000001

But due to the complicated nature of the subject and
the imminent advent of a new -rc cycle, it was
decided to disable the feature for the time being.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch not only fixes a null-pointer de-reference
that would be triggered by a PLINK_OPEN frame with mis-
matching/incompatible mesh configuration, but also
responds correctly to non-compatible PLINK_OPEN frames
by generating a PLINK_CLOSE with the right reason code.

The original bug was detected by smatch.
( http://repo.or.cz/w/smatch.git )

net/mac80211/mesh_plink.c +574 mesh_rx_plink_frame(168)
error: we previously assumed 'sta' could be null.

Cc: <stable@kernel.org>
Reviewed-and-Tested-by: Steve deRosier <steve@cozybit.com>
Reviewed-and-Tested-by: Javier Cardona <javier@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of keeping track of wraparound, clear the counters on every
access and keep separate deltas for ANI and later survey use.
Also moves the function for calculating the 'listen time' for ANI
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Otherwise, if there is an AP and a STATION, and AP
is removed, the NIC will not revert back to STATION mode.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Helps debug multi-VIF scenarios.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some stats for /proc/net/wireless (and wext in general) are not
being set.  This patch addresses a few of those with values easily
obtained from mac80211 core.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Old messages didn't mention the device in question.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 5a254ffe.

The commit failed to take into account that allocated wireless devices
(wiphys) are not added into the device list upon allocation, but only
when they are registered. Therefore, it opened up a race between
allocating and registering a name, so that if two processes allocate and
register concurrently ("alloc, alloc, register, register" rather than
"alloc, register, alloc, register") the code will attempt to use the
same name twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add required suspend/resume support to prevent the SDIO
core from removing our card completely during system suspend.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

Enable runtime PM for the wl1271 SDIO device.

We request power whenever the WLAN interface is brought up,
and release it after the WLAN interface is taken down.

As a result, power is released immediately after probe returns,
since at that point power has not been explicitly requested yet
(i.e. the WLAN interface is still down).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

6000g2 devices need to have temperature offset calibration. The runtime
uCode needs to receive the calibration results just like BB and LO
calibration. To do this, driver reads the offset value from NVM and send
it to uCode after runtime uCode is alive.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn driver uses the IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE
as the chain noise reset calibration index and
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE+1 as the chain noise gain
calibration index, if not specified by the TLV value in the new
firmware format.

However, this is broken if we need to add more calibrations like
the temperature offset calibration because we increased
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE by 1.

To fix this issue, define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE
and use it as the calibration index instead. We still keep the
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE as a sanity check for
the TLV value given by ucode.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For experimental uCode, it should work with the driver
if driver has experimental uCode support option enabled;
remove the API version checking.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>