dev_info() is more appropriate for printing messages when driver
initialization done, so switch to dev_info().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware supports 0.5K, 1K, 2K, 4K RX buffer size, the
RX buffer can not be reused because the hns3_page_order
return 0 when page size and RX buffer size are both 4096.

So this patch changes the hns3_page_order to return 1 when
RX buffer is greater than half of the page size and page size
is less the 8192, and dev_alloc_pages has already been used
to allocate the compound page for RX buffer.

This patch also changes hnae3_* to hns3_* for page order
and RX buffer size calculation because they are used in
hns3 module.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.

This patch sets the above three subtask's affinity using the
misc interrupt' affinity.

Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use delayed work instead of using timers to trigger the
hclge_serive.

Simplify the code with one less middle function and in order
to support misc irq affinity.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some times just see the eth interface have been down/up via
dmesg, but can not know why the eth down. So adds some debug
messages to identify the cause for this.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch modifies firmware version display format in
hclge(vf)_cmd_init() and hns3_get_drvinfo(). Also, adds
some optimizations for firmware version display format.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When allocating memory, the GFP_KERNEL cannot be used during the
spin_lock period. This is because it may cause scheduling when holding
spin_lock. This patch changes GFP flag to GFP_ATOMIC in this case.

Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: lipeng 00277521 <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, hclge_reset_err_handle() will assert a global reset
when the failing count is smaller than MAX_RESET_FAIL_CNT, which
will affect other running functions.

So this patch removes this upgrading, and uses re-scheduling reset
task to do it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some cases, ops->get_reset_level may not be implemented, so we
should check whether it is NULL before calling get_reset_level.
Signed-off-by: Guangbin Huang <huangguangbin@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hns3_set_channels() should check the resetting status firstly,
since the device will reinitialize when resetting. If the
reset has not completed, the hns3_set_channels() may access
invalid memory.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum_acl: Forbid unsupported filters

Patches #1-#2 make mlxsw reject unsupported egress filters. These
include filters that match on VLAN and filters associated with a
redirect action. Patch #1 rejects such filters when they are configured
on egress and patch #2 rejects such filters when they are configured in
a shared block that user tries to bind to egress.

Patch #3 forbids matching on reserved TCP flags as this is not supported
by the current keys that mlxsw uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Matching on reserved TCP flags bits is only supported using custom
parser. Since the usecase for that is not known now, just forbid to
offload rules that match on these bits.
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some matches and actions are not supported on egress. Track such rules
and forbid a bind of block which contains them to egress.

With this patch, the kernel tells the user he cannot do that:
$ tc qdisc add dev ens16np1 ingress_block 22 clsact
$ tc filter add block 22 protocol 802.1q pref 2 handle 101 flower vlan_id 100 skip_sw action pass
$ tc qdisc add dev ens16np2 egress_block 22 clsact
Error: mlxsw_spectrum: Block cannot be bound to egress because it contains unsupported rules.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum ASIC does not support redirection on egress, so refuse to
insert such flows:

$ tc qdisc add dev ens16np1 clsact
$ tc filter add dev ens16np1 egress protocol all pref 1 handle 101 flower skip_sw action mirred egress redirect dev ens16np2
Error: mlxsw_spectrum: Redirect action is not supported on egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: improve HW csum and TSO handling

This series:
- delegates more tasks from the driver to the core
- enables HW csum and TSO per default
- copies quirks for buggy chip versions from vendor driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable HW csum and TSO per default except on known buggy chip versions.
Realtek confirmed that RTL8168evl has a HW issue with TSO.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The loop in r8169_csum_workaround is called only if in
msdn_giant_send_check a copy of the skb header needs to be made and
we don't have enough memory. Let's simply drop the packet in that case
so that we can remove r8169_csum_workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement callback ndo_features_check and move all feature checks there.
This will allow us to get rid of r8169_csum_workaround() completely in
a subsequent step. Like in the vendor driver disable HW csum for short
packets on RTL8168b.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set GSO max size and max segment number as in the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_find_hdr() prints a non-rate limited error message
when it cannot find an ipv6 header at a specific offset.
This could be used as a DoS, so just remove it.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Align setting PME with the vendor driver. PMEnable is writable on
RTL8169 only, on later chip versions it's read-only. PME_SIGNAL is
used on chip versions from RTL8168evl with the exception of the
RTL8168f family.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ConnectX-3 Pro can offload transmission of VLAN packets with VXLAN inside:
enable tunnel offloads in dev->vlan_features, like it's done with other
NIC drivers (e.g. be2net and ixgbe).

It's no more necessary to change dev->hw_enc_features when VXLAN are added
or removed, since .ndo_features_check() already checks for VXLAN packet
where the UDP destination port matches the configured value. Just set
dev->hw_enc_features when the NIC is initialized, so that overlying VLAN
can correctly inherit the tunnel offload capabilities.

Changes since v1:
- avoid flipping hw_enc_features, instead of calling netdev notifiers,
  thanks to Saeed Mahameed
- squash two patches into a single one

CC: Paolo Abeni <pabeni@redhat.com>
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_ACPI is unset (arm allyesconfig), status is unused.

drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c:383:14: warning:
unused variable 'status' [-Wunused-variable]
        acpi_status status;
                    ^
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:440:14: warning:
unused variable 'status' [-Wunused-variable]
        acpi_status status;
                    ^
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:697:14: warning: unused
variable 'status' [-Wunused-variable]
        acpi_status status;
                    ^

Move the declaration into the CONFIG_ACPI block so that there are no
compiler warnings.

Fixes: 570d785b ("drivers: net: xgene: Remove acpi_has_method() calls")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stmmaceth clock is specified by the slave_bus and apb_pclk clocks in
the device tree bindings for snps,dwc-qos-ethernet-4.10 compatible nodes
of this IP.

The subdrivers for these bindings will be requesting the stmmac clock
correctly at a later point, so there is no need to request it here and
cause an error message to be printed to the kernel log.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Tegra EQOS driver already resets the MDIO bus at probe time via the
reset GPIO specified in the phy-reset-gpios device tree property. There
is no need to reset the bus again later on.

This avoids the need to query the device tree for the snps,reset GPIO,
which is not part of the Tegra EQOS device tree bindings. This quiesces
an error message from the generic bus reset code if it doesn't find the
snps,reset related delays.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable bucket is being initialized with a value that is never
read and it is being updated later with a new value in a following
for-loop. The initialization is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement ethtool's EEPROM dump command (ethtool -e|--eeprom-dump).

Thx to Andrew Lunn for comments.
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/staging/octeon/ethernet-tx.c:287:23: error: implicit declaration of function 'skb_drag_size'; did you mean 'skb_frag_size'? [-Werror=implicit-function-declaration]

From kernelci report:

	https://kernelci.org/build/id/5d3943f859b514103f688918/logs/

Fixes: 92493a2f ("Build fixes for skb_frag_size conversion")
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_platform_ioremap_resource() wraps platform_get_resource() and
devm_ioremap_resource() in a single helper, let's use that helper to
simplify the code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tuong Lien says:

====================
tipc: link changeover issues

This patch series is to resolve some issues found with the current link
changeover mechanism, it also includes an optimization for the link
synching.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In conjunction with changing the interfaces' MTU (e.g. especially in
the case of a bonding) where the TIPC links are brought up and down
in a short time, a couple of issues were detected with the current link
changeover mechanism:

1) When one link is up but immediately forced down again, the failover
procedure will be carried out in order to failover all the messages in
the link's transmq queue onto the other working link. The link and node
state is also set to FAILINGOVER as part of the process. The message
will be transmited in form of a FAILOVER_MSG, so its size is plus of 40
bytes (= the message header size). There is no problem if the original
message size is not larger than the link's MTU - 40, and indeed this is
the max size of a normal payload messages. However, in the situation
above, because the link has just been up, the messages in the link's
transmq are almost SYNCH_MSGs which had been generated by the link
synching procedure, then their size might reach the max value already!
When the FAILOVER_MSG is built on the top of such a SYNCH_MSG, its size
will exceed the link's MTU. As a result, the messages are dropped
silently and the failover procedure will never end up, the link will
not be able to exit the FAILINGOVER state, so cannot be re-established.

2) The same scenario above can happen more easily in case the MTU of
the links is set differently or when changing. In that case, as long as
a large message in the failure link's transmq queue was built and
fragmented with its link's MTU > the other link's one, the issue will
happen (there is no need of a link synching in advance).

3) The link synching procedure also faces with the same issue but since
the link synching is only started upon receipt of a SYNCH_MSG, dropping
the message will not result in a state deadlock, but it is not expected
as design.

The 1) & 3) issues are resolved by the last commit that only a dummy
SYNCH_MSG (i.e. without data) is generated at the link synching, so the
size of a FAILOVER_MSG if any then will never exceed the link's MTU.

For the 2) issue, the only solution is trying to fragment the messages
in the failure link's transmq queue according to the working link's MTU
so they can be failovered then. A new function is made to accomplish
this, it will still be a TUNNEL PROTOCOL/FAILOVER MSG but if the
original message size is too large, it will be fragmented & reassembled
at the receiving side.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit along with the next one are to resolve the issues with the
link changeover mechanism. See that commit for details.

Basically, for the link synching, from now on, we will send only one
single ("dummy") SYNCH message to peer. The SYNCH message does not
contain any data, just a header conveying the synch point to the peer.

A new node capability flag ("TIPC_TUNNEL_ENHANCED") is introduced for
backward compatible!
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_ioremap_resource already contains error message, so remove
the redundant dev_err message
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Two small updates

Patch #1, from Amit, exposes the size of the key-value database (KVD)
where different entries (e.g., routes, neighbours) are stored in the
device. This allows users to understand how many entries can be
offloaded and is also useful for writing scale tests.

Patch #2 increases the number of IPv6 nexthop groups mlxsw can offload.
The problem and solution are explained in detail in the commit message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike IPv4, the kernel does not consolidate IPv6 nexthop groups. To
avoid exhausting the device's adjacency table - where nexthops are
stored - the driver does this consolidation instead.

Each nexthop group is hashed by XOR-ing the interface indexes of all the
member nexthop devices. However, the ifindex itself is not hashed, which
can result in identical keys used for different groups and finally an
-EBUSY error from rhashtable due to too long objects list.

Improve the situation by hashing the ifindex itself.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike Spectrum-1, the KVD (Key-value database) of Spectrum-2 is not
partitioned, so only expose the entire KVD size. This enables users to
query the total size of the KVD.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move from i2c_new_dummy() to i2c_new_dummy_device(). So, we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mlx4_dev_cap and mlx4_init_hca_param are really too large
to be put on the kernel stack, as shown by this clang warning:

drivers/net/ethernet/mellanox/mlx4/main.c:3304:12: error: stack frame size of 1088 bytes in function 'mlx4_load_one' [-Werror,-Wframe-larger-than=]

With gcc, the problem is the same, but it does not warn because
it does not inline this function, and therefore stays just below
the warning limit, while clang is just above it.

Use kzalloc for dynamic allocation instead of putting them
on stack. This gets the combined stack frame down to 424 bytes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clang warns about an overly large stack frame in one function
when it decides to inline all __qed_get_vport_*() functions into
__qed_get_vport_stats():

drivers/net/ethernet/qlogic/qed/qed_l2.c:1889:13: error: stack frame size of 1128 bytes in function '_qed_get_vport_stats' [-Werror,-Wframe-larger-than=]

Use a noinline_for_stack annotation to prevent clang from inlining
these, which keeps the maximum stack usage at around half of that
in the worst case, similar to what we get with gcc.

Fixes: 86622ee7 ("qed: Move statistics to L2 code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch improves and simplifies rtl_set_rx_mode a little.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>