- 20 Nov, 2016 40 commits
-
-
Peter Wu authored
commit a12e78dd upstream. Return the set of supported functions to the caller. No functional changes. Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Peter Wu <peter@lekensteyn.nl> Acked-by: Dave Airlie <airlied@redhat.com Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Peter Wu authored
commit df42194a upstream. Ensure that the returned set of supported DSM functions (MUX, Optimus) match the ACPI handle that is set in nouveau_dsm_pci_probe. As there are no machines with a MUX function on just one PCI device and an Optimus on another, there should not be a functional impact. This change however makes this implicit assumption more obvious. Convert int to bool and rename has_dsm to has_mux while at it. Let the caller set nouveau_dsm_priv.dhandle as needed. v2: pass dhandle to the caller. Reviewed-by:
-
Mikulas Patocka authored
commit 28668f43 upstream. The patch f045f459 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses") tries to fix some out of memory accesses. Unfortunatelly, the patch breaks the display when using fonts with width that is not divisiable by 8. The monochrome bitmap for each character is stored in memory by lines from top to bottom. Each line is padded to a full byte. For example, for 22x11 font, each line is padded to 16 bits, so each character is consuming 44 bytes total, that is 11 32-bit words. The patch f045f459 changed the logic to "dsize = ALIGN(image->width * image->height, 32) >> 5", that is just 8 words - this is incorrect and it causes display corruption. This patch adds the necesary padding of lines to 8 bytes. This patch should be backported to stable kernels where f045f459 was backported. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Fixes: f045f459 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses") Signed-off-by:
-
Richard Weinberger authored
commit 74f2c6e9 upstream. Since PEB erasure is asynchornous it can happen that there is more than one Fastmap on the MTD. This is fine because the attach logic will pick the Fastmap data structure with the highest sequence number. On a not so well configured MTD stack spurious ECC errors are common. Causes can be different, bad hardware, wrong operating modes, etc... If the most current Fastmap renders bad due to ECC errors UBI might pick an older Fastmap to attach from. While this can only happen on an anyway broken setup it will show completely different sympthoms and makes finding the root cause much more difficult. So, be debug friendly and fall back to scanning mode of we're facing an ECC error while scanning for Fastmap. Signed-off-by:
Richard Weinberger <richard@nod.at> [bwh: Backported to 3.16: - In scan_fast(), use 'ai' instead of 'scan_ai' - Adjust context] Signed-off-by:
-
Richard Weinberger authored
commit 4946784b upstream. When the volume resize operation shrinks a volume, LEBs will be unmapped. Since unmapping will not erase these LEBs immediately we have to wait for that operation to finish. Otherwise in case of a power cut right after writing the new volume table the UBI attach process can find more LEBs than the volume table knows. This will render the UBI image unattachable. Fix this issue by waiting for erase to complete and write the new volume table afterward. Reported-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by:
-
Iosif Harutyunov authored
commit 714fb87e upstream. Install the UBI device object before we arm sysfs. Otherwise udev tries to read sysfs attributes before UBI is ready and udev rules will not match. Signed-off-by:
Iosif Harutyunov <iharutyunov@sonicwall.com> [rw: massaged commit message] Signed-off-by:
-
Wei Fang authored
commit 9446385f upstream. FUSE_HAS_IOCTL_DIR should be assigned to ->flags, it may be a typo. Signed-off-by:
Wei Fang <fangwei1@huawei.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Fixes: 69fe05c9 ("fuse: add missing INIT flags") Signed-off-by:
-
Maxim Patlasov authored
commit 9ebce595 upstream. fuse_flush() calls write_inode_now() that triggers writeback, but actual writeback will happen later, on fuse_sync_writes(). If an error happens, fuse_writepage_end() will set error bit in mapping->flags. So, we have to check mapping->flags after fuse_sync_writes(). Signed-off-by:
Maxim Patlasov <mpatlasov@virtuozzo.com> Signed-off-by:
-
Alexey Kuznetsov authored
commit ac7f052b upstream. Due to implementation of fuse writeback filemap_write_and_wait_range() does not catch errors. We have to do this directly after fuse_sync_writes() Signed-off-by:
Alexey Kuznetsov <kuznet@virtuozzo.com> Signed-off-by:
-
Dan Carpenter authored
commit 55f1cf83 upstream. The pio_dev[] array has MAX_NR_PIO_DEVICES elements so the > should be >=. Fixes: 5f97f7f9 ('[PATCH] avr32 architecture') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
James Hogan authored
commit 3146bc64 upstream. AT_VECTOR_SIZE_ARCH should be defined with the maximum number of NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined for arm64 at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for the VDSO address. This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for AT_BASE_PLATFORM which arm64 doesn't use, but lets define it now and add the comment above ARCH_DLINFO as found in several other architectures to remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to date. Fixes: f668cd16 ("arm64: ELF definitions") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
James Hogan authored
commit 0758b116 upstream. The protected_writeback_scache_line() function is used by local_r4k_flush_cache_sigtramp() to flush an FPU delay slot emulation trampoline on the userland stack from the caches so it is visible to subsequent instruction fetches. Commit de8974e3 ("MIPS: asm: r4kcache: Add EVA cache flushing functions") updated some protected_ cache flush functions to use EVA CACHEE instructions via protected_cachee_op(), and commit 83fd4344 ("MIPS: r4kcache: Add EVA case for protected_writeback_dcache_line") did the same thing for protected_writeback_dcache_line(), but protected_writeback_scache_line() never got updated. Lets fix that now to flush the right user address from the secondary cache rather than some arbitrary kernel unmapped address. This issue was spotted through code inspection, and it seems unlikely to be possible to hit this in practice. It theoretically affect EVA kernels on EVA capable cores with an L2 cache, where the icache fetches straight from RAM (cpu_icache_snoops_remote_store == 0), running a hard float userland with FPU disabled (nofpu). That both Malta and Boston platforms override cpu_icache_snoops_remote_store to 1 suggests that all MIPS cores fetch instructions into icache straight from L2 rather than RAM. Fixes: de8974e3 ("MIPS: asm: r4kcache: Add EVA cache flushing functions") Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Alex Deucher authored
commit 3edc38a0 upstream. Some of the checks didn't handle frev 2 tables properly. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
David Howells authored
commit 20f06ed9 upstream. MIPS64 needs to use compat_sys_keyctl for 32-bit userspace rather than calling sys_keyctl. The latter will work in a lot of cases, thereby hiding the issue. Reported-by:
Stephan Mueller <smueller@chronox.de> Signed-off-by:
David Howells <dhowells@redhat.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: linux-security-module@vger.kernel.org Cc: keyrings@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13832/Signed-off-by:
-
Dan Carpenter authored
commit 344e3c77 upstream. We accidentally take the "port->lock" twice in a row. This old code was supposed to be deleted. Fixes: e58e241c ('sparc: serial: Clean up the locking for -rt') Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Pavel Shilovsky authored
commit 7893242e upstream. During following a symbolic link we received err_buf from SMB2_open(). While the validity of SMB2 error response is checked previously in smb2_check_message() a symbolic link payload is not checked at all. Fix it by adding such checks. Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Phil Turnbull authored
commit 955818cd upstream. ceph_llseek does not correctly return NXIO errors because the 'out' path always returns 'offset'. Fixes: 06222e49 ("fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek") Signed-off-by:
Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by:
Yan, Zheng <zyan@redhat.com> [bwh: Backported to 3.16; adjust context] Signed-off-by:
-
Dmitry Torokhov authored
commit 40974618 upstream. As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we have a hard load dependency between i8042 and atkbd which prevents keyboard from working on Gen2 Hyper-V VMs. > hyperv_keyboard invokes serio_interrupt(), which needs a valid serio > driver like atkbd.c. atkbd.c depends on libps2.c because it invokes > ps2_command(). libps2.c depends on i8042.c because it invokes > i8042_check_port_owner(). As a result, hyperv_keyboard actually > depends on i8042.c. > > For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a > Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m > rather than =y, atkbd.ko can't load because i8042.ko can't load(due to > no i8042 device emulated) and finally hyperv_keyboard can't work and > the user can't input: https://bugs.archlinux.org/task/39820 > (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y) To break the dependency we move away from using i8042_check_port_owner() and instead allow serio port owner specify a mutex that clients should use to serialize PS/2 command stream. Reported-by:
Mark Laws <mdl@60hz.org> Tested-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Ben Hutchings authored
commit b8612e51 upstream. Signing a module should only make it trusted by the specific kernel it was built for, not anything else. If a module signing key is used for multiple ABI-incompatible kernels, the modules need to include enough version information to distinguish them. Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au>
-
Ben Hutchings authored
commit bca014ca upstream. Signing a module should only make it trusted by the specific kernel it was built for, not anything else. Loading a signed module meant for a kernel with a different ABI could have interesting effects. Therefore, treat all signatures as invalid when a module is force-loaded. Signed-off-by:
-
phil.turnbull@oracle.com authored
commit 4ac36a4a upstream. If 'tunnel' is NULL we should return -EBADF but the 'end_put_sess' path unconditionally sets 'error' back to zero. Rework the error path so it more closely matches pppol2tp_sendmsg. Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
-
Vegard Nossum authored
commit d3e6952c upstream. I ran into this: kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 2 PID: 2012 Comm: trinity-c3 Not tainted 4.7.0-rc7+ #19 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014 task: ffff8800b745f2c0 ti: ffff880111740000 task.ti: ffff880111740000 RIP: 0010:[<ffffffff82bbf066>] [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710 RSP: 0018:ffff880111747bb8 EFLAGS: 00010286 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000069dd8358 RDX: 0000000000000009 RSI: 0000000000000027 RDI: 0000000000000048 RBP: ffff880111747c00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000069dd8358 R11: 1ffffffff0759723 R12: 0000000000000000 R13: ffff88011a7e4780 R14: 0000000000000027 R15: 0000000000000000 FS: 00007fc738404700(0000) GS:ffff88011af00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc737fdfb10 CR3: 0000000118087000 CR4: 00000000000006e0 Stack: 0000000000000200 ffff880111747bd8 ffffffff810ee611 ffff880119f1f220 ffff880119f1f4f8 ffff880119f1f4f0 ffff88011a7e4780 ffff880119f1f232 ffff880119f1f220 ffff880111747d58 ffffffff82bca542 0000000000000000 Call Trace: [<ffffffff82bca542>] irda_connect+0x562/0x1190 [<ffffffff825ae582>] SYSC_connect+0x202/0x2a0 [<ffffffff825b4489>] SyS_connect+0x9/0x10 [<ffffffff8100334c>] do_syscall_64+0x19c/0x410 [<ffffffff83295ca5>] entry_SYSCALL64_slow_path+0x25/0x25 Code: 41 89 ca 48 89 e5 41 57 41 56 41 55 41 54 41 89 d7 53 48 89 fb 48 83 c7 48 48 89 fa 41 89 f6 48 c1 ea 03 48 83 ec 20 4c 8b 65 10 <0f> b6 04 02 84 c0 74 08 84 c0 0f 8e 4c 04 00 00 80 7b 48 00 74 RIP [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710 RSP <ffff880111747bb8> ---[ end trace 4cda2588bc055b30 ]--- The problem is that irda_open_tsap() can fail and leave self->tsap = NULL, and then irttp_connect_request() almost immediately dereferences it. Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
-
James Hogan authored
commit cdf8b463 upstream. AT_VECTOR_SIZE_ARCH should be defined with the maximum number of NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined for tile at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for the VDSO address. This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for AT_BASE_PLATFORM which tile doesn't use, but lets define it now and add the comment above ARCH_DLINFO as found in several other architectures to remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to date. Fixes: 4a556f4f ("tile: implement gettimeofday() via vDSO") Signed-off-by:
Chris Metcalf <cmetcalf@mellanox.com> Signed-off-by:
-
Sebastian Reichel authored
commit b46211d6 upstream. Add missing sysconfig/sysstatus information to OMAP3 hwmod. The information has been checked against OMAP34xx and OMAP36xx TRM. Without this change DSI block is not reset during boot, which is required for working Nokia N950 display. Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Jiri Slaby authored
commit 368301f2 upstream. With this command sequence: modprobe plip modprobe pps_parport rmmod pps_parport the partport_pps modules causes this crash: BUG: unable to handle kernel NULL pointer dereference at (null) IP: parport_detach+0x1d/0x60 [pps_parport] Oops: 0000 [#1] SMP ... Call Trace: parport_unregister_driver+0x65/0xc0 [parport] SyS_delete_module+0x187/0x210 The sequence that builds up to this is: 1) plip is loaded and takes the parport device for exclusive use: plip0: Parallel port at 0x378, using IRQ 7. 2) pps_parport then fails to grab the device: pps_parport: parallel port PPS client parport0: cannot grant exclusive access for device pps_parport pps_parport: couldn't register with parport0 3) rmmod of pps_parport is then killed because it tries to access pardev->name, but pardev (taken from port->cad) is NULL. So add a check for NULL in the test there too. Link: http://lkml.kernel.org/r/20160714115245.12651-1-jslaby@suse.czSigned-off-by:
Jiri Slaby <jslaby@suse.cz> Acked-by:
Rodolfo Giometti <giometti@enneenne.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Dan Carpenter authored
commit 2d6a4d64 upstream. The curly braces are missing here so we print stuff unintentionally. Fixes: 9da4714a ('slub: slabinfo update for cmpxchg handling') Link: http://lkml.kernel.org/r/20160715211243.GE19522@mwandaSigned-off-by:
Christoph Lameter <cl@linux.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Laura Abbott <labbott@fedoraproject.org> Signed-off-by:
-
Andrey Ryabinin authored
commit 3cb9185c upstream. radix_tree_iter_retry() resets slot to NULL, but it doesn't reset tags. Then NULL slot and non-zero iter.tags passed to radix_tree_next_slot() leading to crash: RIP: radix_tree_next_slot include/linux/radix-tree.h:473 find_get_pages_tag+0x334/0x930 mm/filemap.c:1452 .... Call Trace: pagevec_lookup_tag+0x3a/0x80 mm/swap.c:960 mpage_prepare_extent_to_map+0x321/0xa90 fs/ext4/inode.c:2516 ext4_writepages+0x10be/0x2b20 fs/ext4/inode.c:2736 do_writepages+0x97/0x100 mm/page-writeback.c:2364 __filemap_fdatawrite_range+0x248/0x2e0 mm/filemap.c:300 filemap_write_and_wait_range+0x121/0x1b0 mm/filemap.c:490 ext4_sync_file+0x34d/0xdb0 fs/ext4/fsync.c:115 vfs_fsync_range+0x10a/0x250 fs/sync.c:195 vfs_fsync fs/sync.c:209 do_fsync+0x42/0x70 fs/sync.c:219 SYSC_fdatasync fs/sync.c:232 SyS_fdatasync+0x19/0x20 fs/sync.c:230 entry_SYSCALL_64_fastpath+0x23/0xc1 arch/x86/entry/entry_64.S:207 We must reset iterator's tags to bail out from radix_tree_next_slot() and go to the slow-path in radix_tree_next_chunk(). Fixes: 46437f9a ("radix-tree: fix race in gang lookup") Link: http://lkml.kernel.org/r/1468495196-10604-1-git-send-email-aryabinin@virtuozzo.comSigned-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Acked-by:
Konstantin Khlebnikov <koct9i@gmail.com> Cc: Matthew Wilcox <willy@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
-
Benjamin Coddington authored
commit 149a4fdd upstream. NFS doesn't expect requests with wb_bytes set to zero and may make unexpected decisions about how to handle that request at the page IO layer. Skip request creation if we won't have any wb_bytes in the request. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Reviewed-by:
Weston Andros Adamson <dros@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Andy Shevchenko authored
commit 3dbd3212 upstream. The commit d56d6b3d ("gpio: langwell: add Intel Merrifield support") doesn't look at all as a proper support for Intel Merrifield and I dare to say that it distorts the behaviour of the hardware. The register map is different on Intel Merrifield, i.e. only 6 out of 8 register have the same purpose but none of them has same location in the address space. The current case potentially harmful to existing hardware since it's poking registers on wrong offsets and may set some pin to be GPIO output when connected hardware doesn't expect such. Besides the above GPIO and pinctrl on Intel Merrifield have been located in different IP blocks. The functionality has been extended as well, i.e. added support of level interrupts, special registers for wake capable sources and thus, in my opinion, requires a completele separate driver. If someone wondering the existing gpio-intel-mid.c would be converted to actual pinctrl (which by the fact it is now), though I wouldn't be a volunteer to do that. Fixes: d56d6b3d ("gpio: langwell: add Intel Merrifield support") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Ilya Dryomov authored
commit 930c5328 upstream. Currently, osd_weight and osd_state fields are updated in the encoding order. This is wrong, because an incremental map may look like e.g. new_up_client: { osd=6, addr=... } # set osd_state and addr new_state: { osd=6, xorstate=EXISTS } # clear osd_state Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After applying new_up_client, osd_state is changed to EXISTS | UP. Carrying on with the new_state update, we flip EXISTS and leave osd6 in a weird "!EXISTS but UP" state. A non-existent OSD is considered down by the mapping code 2087 for (i = 0; i < pg->pg_temp.len; i++) { 2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) { 2089 if (ceph_can_shift_osds(pi)) 2090 continue; 2091 2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE; and so requests get directed to the second OSD in the set instead of the first, resulting in OSD-side errors like: [WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680 and hung rbds on the client: [ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0) [ 493.566805] rbd: rbd0: result -6 xferred 400000 [ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688 The fix is to decouple application from the decoding and: - apply new_weight first - apply new_state before new_up_client - twiddle osd_state flags if marking in - clear out some of the state if osd is destroyed Fixes: http://tracker.ceph.com/issues/14901Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Josh Durgin <jdurgin@redhat.com> Signed-off-by:
-
Yan, Zheng authored
commit 6dd74e44 upstream. Signed-off-by:
Sage Weil <sage@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
commit b4e76f7e upstream. Dan Carpenter reported [1] a static checker warning that ctx->offsets[] may be accessed off by one from build_body(), since it's allocated with fp->len * sizeof(*ctx.offsets) as length. The cBPF arm and ppc code doesn't have this issue as claimed, so only mips seems to be affected and should like most other JITs allocate with fp->len + 1. A few number of JITs (x86, sparc, arm64) handle this differently, where they only require fp->len array elements. [1] http://www.spinics.net/lists/mips/msg64193.html Fixes: c6610de3 ("MIPS: net: Add BPF JIT") Reported-by:
Daniel Borkmann <daniel@iogearbox.net> Cc: Alexei Starovoitov <ast@kernel.org> Cc: ast@kernel.org Cc: linux-mips@linux-mips.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13814/Signed-off-by:
-
Dan Carpenter authored
commit 58a7e1c1 upstream. We obviously intended to enable IRQs again at the end. Fixes: 745aef5d ('MIPS: RM7000: Add support for tertiary cache') Signed-off-by:
-
Dmitry Torokhov authored
commit 510cccb5 upstream. The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS, which is currently 256, whereas number of keys/buttons in input device (and therefor in key_down) is much larger - KEY_CNT - 768, and that can cause out-of-bound access when we do sym = U(key_maps[0][k]); with large 'k'. To fix it we should not attempt iterating beyond smaller of NR_KEYS and KEY_CNT. Also while at it let's switch to for_each_set_bit() instead of open-coding it. Reported-by:
Sasha Levin <sasha.levin@oracle.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Feng Li authored
commit 8abc718d upstream. In MC/S scenario, the conn->sess has been set NULL in iscsi_login_non_zero_tsih_s1 when the second connection comes here, then kernel panic. The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So we should check whether it's NULL before calling. Signed-off-by:
Feng Li <lifeng1519@gmail.com> Tested-by:
Sumit Rai <sumit.rai@calsoftinc.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Michael Walle authored
commit b53893aa upstream. According to the datasheet you should only write 1 to this bit. If it is not set, at least AIN3 will return bad values on newer silicon revisions. Fixes: d84ca5b3 ("hwmon: Add driver for ADT7411 voltage and temperature sensor") Signed-off-by:
Michael Walle <michael@walle.cc> Signed-off-by:
-
Rabin Vincent authored
commit bd975d1e upstream. The secmech hmac(md5) structures are present in the TCP_Server_Info struct and can be shared among multiple CIFS sessions. However, the server mutex is not currently held when these structures are allocated and used, which can lead to a kernel crashes, as in the scenario below: mount.cifs(8) #1 mount.cifs(8) #2 Is secmech.sdeschmaccmd5 allocated? // false Is secmech.sdeschmaccmd5 allocated? // false secmech.hmacmd = crypto_alloc_shash.. secmech.sdeschmaccmd5 = kzalloc.. sdeschmaccmd5->shash.tfm = &secmec.hmacmd; secmech.sdeschmaccmd5 = kzalloc // sdeschmaccmd5->shash.tfm // not yet assigned crypto_shash_update() deref NULL sdeschmaccmd5->shash.tfm Unable to handle kernel paging request at virtual address 00000030 epc : 8027ba34 crypto_shash_update+0x38/0x158 ra : 8020f2e8 setup_ntlmv2_rsp+0x4bc/0xa84 Call Trace: crypto_shash_update+0x38/0x158 setup_ntlmv2_rsp+0x4bc/0xa84 build_ntlmssp_auth_blob+0xbc/0x34c sess_auth_rawntlmssp_authenticate+0xac/0x248 CIFS_SessSetup+0xf0/0x178 cifs_setup_session+0x4c/0x84 cifs_get_smb_ses+0x2c8/0x314 cifs_mount+0x38c/0x76c cifs_do_mount+0x98/0x440 mount_fs+0x20/0xc0 vfs_kern_mount+0x58/0x138 do_mount+0x1e8/0xccc SyS_mount+0x88/0xd4 syscall_common+0x30/0x54 Fix this by locking the srv_mutex around the code which uses these hmac(md5) structures. All the other secmech algos already have similar locking. Fixes: 95dc8dd1 ("Limit allocation of crypto mechanisms to dialect which requires") Signed-off-by:
Rabin Vincent <rabinv@axis.com> Acked-by:
Sachin Prabhu <sprabhu@redhat.com> Signed-off-by:
-
Mike Christie authored
commit ea263c7f upstream. max_discard_sectors only 32bits, and some non scsi backend devices will set this to the max 0xffffffff, so we can end up overflowing during the max_unmap_lba_count calculation. This fixes a regression caused by my patch: commit 8a9ebe71 Author: Mike Christie <mchristi@redhat.com> Date: Mon Jan 18 14:09:27 2016 -0600 target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors which can result in extra discards being sent to due the overflow causing max_unmap_lba_count to be smaller than what the backing device can actually support. Signed-off-by:
Mike Christie <mchristi@redhat.com> Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 064cdd2d upstream. This patch fixes a race in iscsit_release_commands_from_conn() -> iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1, where CMD_T_FABRIC_STOP could end up being set after the final kref_put() is called from core_tmr_abort_task() context. This results in transport_generic_free_cmd() blocking indefinately on se_cmd->cmd_wait_comp, because the target_release_cmd_kref() check for CMD_T_FABRIC_STOP returns false. To address this bug, make iscsit_release_commands_from_conn() do list_splice and set CMD_T_FABRIC_STOP early while holding iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been set. Finally in target_release_cmd_kref(), only honor fabric_stop if CMD_T_ABORTED has been set. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by:
-
Nicholas Bellinger authored
commit 5e2c956b upstream. During transport_generic_free_cmd() with a concurrent TMR ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the caller will be blocked on se_cmd->cmd_wait_stop completion until the final kref_put() -> target_release_cmd_kref() has been invoked to call complete(). However, when ABORT_TASK is completed with FUNCTION_COMPLETE in core_tmr_abort_task(), the aborted se_cmd will have already been removed from se_sess->sess_cmd_list via list_del_init(). This results in target_release_cmd_kref() hitting the legacy list_empty() == true check, invoking ->release_cmd() but skipping complete() to wakeup se_cmd->cmd_wait_stop blocked earlier in transport_generic_free_cmd() code. To address this bug, it's safe to go ahead and drop the original list_empty() check so that fabric_stop invokes the complete() as expected, since list_del_init() can safely be used on a empty list. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by:
-
