- 05 Jul, 2017 16 commits
-
-
Serhey Popovych authored
[ Upstream commit db833d40 ] Network interface groups support added while ago, however there is no IFLA_GROUP attribute description in policy and netlink message size calculations until now. Add IFLA_GROUP attribute to the policy. Fixes: cbda10fa ("net_device: add support for network device groups") Signed-off-by:
Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Serhey Popovych authored
[ Upstream commit 07f61557 ] While commit 73ba57bf ("ipv6: fix backtracking for throw routes") does good job on error propagation to the fib_rules_lookup() in fib rules core framework that also corrects throw routes handling, it does not solve route reference leakage problem happened when we return -EAGAIN to the fib_rules_lookup() and leave routing table entry referenced in arg->result. If rule with matched throw route isn't last matched in the list we overwrite arg->result losing reference on throw route stored previously forever. We also partially revert commit ab997ad4 ("ipv6: fix the incorrect return value of throw route") since we never return routing table entry with dst.error == -EAGAIN when CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point to check for RTF_REJECT flag since it is always set throw route. Fixes: 73ba57bf ("ipv6: fix backtracking for throw routes") Signed-off-by:
-
Bert Kenward authored
efx_probe_all() calls efx->type->vswitching_probe during probe. For SFC4000 (Falcon) NICs this function is not defined, leading to a BUG with the top of the call stack similar to: ? efx_pci_probe_main+0x29a/0x830 efx_pci_probe+0x7d3/0xe70 vswitching_restore and vswitching_remove also need to be defined. Fixed in mainline by: commit 5a6681e2 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver") Fixes: 6d8aaaf6 ("sfc: create VEB vswitch and vport above default firmware setup") Signed-off-by:
Bert Kenward <bkenward@solarflare.com> Signed-off-by:
-
Gao Feng authored
[ Upstream commit 9745e362 ] The register_vlan_device would invoke free_netdev directly, when register_vlan_dev failed. It would trigger the BUG_ON in free_netdev if the dev was already registered. In this case, the netdev would be freed in netdev_run_todo later. So add one condition check now. Only when dev is not registered, then free it directly. The following is the part coredump when netdev_upper_dev_link failed in register_vlan_dev. I removed the lines which are too long. [ 411.237457] ------------[ cut here ]------------ [ 411.237458] kernel BUG at net/core/dev.c:7998! [ 411.237484] invalid opcode: 0000 [#1] SMP [ 411.237705] [last unloaded: 8021q] [ 411.237718] CPU: 1 PID: 12845 Comm: vconfig Tainted: G E 4.12.0-rc5+ #6 [ 411.237737] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015 [ 411.237764] task: ffff9cbeb6685580 task.stack: ffffa7d2807d8000 [ 411.237782] RIP: 0010:free_netdev+0x116/0x120 [ 411.237794] RSP: 0018:ffffa7d2807dbdb0 EFLAGS: 00010297 [ 411.237808] RAX: 0000000000000002 RBX: ffff9cbeb6ba8fd8 RCX: 0000000000001878 [ 411.237826] RDX: 0000000000000001 RSI: 0000000000000282 RDI: 0000000000000000 [ 411.237844] RBP: ffffa7d2807dbdc8 R08: 0002986100029841 R09: 0002982100029801 [ 411.237861] R10: 0004000100029980 R11: 0004000100029980 R12: ffff9cbeb6ba9000 [ 411.238761] R13: ffff9cbeb6ba9060 R14: ffff9cbe60f1a000 R15: ffff9cbeb6ba9000 [ 411.239518] FS: 00007fb690d81700(0000) GS:ffff9cbebb640000(0000) knlGS:0000000000000000 [ 411.239949] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 411.240454] CR2: 00007f7115624000 CR3: 0000000077cdf000 CR4: 00000000003406e0 [ 411.240936] Call Trace: [ 411.241462] vlan_ioctl_handler+0x3f1/0x400 [8021q] [ 411.241910] sock_ioctl+0x18b/0x2c0 [ 411.242394] do_vfs_ioctl+0xa1/0x5d0 [ 411.242853] ? sock_alloc_file+0xa6/0x130 [ 411.243465] SyS_ioctl+0x79/0x90 [ 411.243900] entry_SYSCALL_64_fastpath+0x1e/0xa9 [ 411.244425] RIP: 0033:0x7fb69089a357 [ 411.244863] RSP: 002b:00007ffcd04e0fc8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 [ 411.245445] RAX: ffffffffffffffda RBX: 00007ffcd04e2884 RCX: 00007fb69089a357 [ 411.245903] RDX: 00007ffcd04e0fd0 RSI: 0000000000008983 RDI: 0000000000000003 [ 411.246527] RBP: 00007ffcd04e0fd0 R08: 0000000000000000 R09: 1999999999999999 [ 411.246976] R10: 000000000000053f R11: 0000000000000202 R12: 0000000000000004 [ 411.247414] R13: 00007ffcd04e1128 R14: 00007ffcd04e2888 R15: 0000000000000001 [ 411.249129] RIP: free_netdev+0x116/0x120 RSP: ffffa7d2807dbdb0 Signed-off-by:
Gao Feng <gfree.wind@vip.163.com> Signed-off-by:
-
Wei Wang authored
[ Upstream commit 76371d2e ] In the existing dn_route.c code, dn_route_output_slow() takes dst->__refcnt before calling dn_insert_route() while dn_route_input_slow() does not take dst->__refcnt before calling dn_insert_route(). This makes the whole routing code very buggy. In dn_dst_check_expire(), dnrt_free() is called when rt expires. This makes the routes inserted by dn_route_output_slow() not able to be freed as the refcnt is not released. In dn_dst_gc(), dnrt_drop() is called to release rt which could potentially cause the dst->__refcnt to be dropped to -1. In dn_run_flush(), dst_free() is called to release all the dst. Again, it makes the dst inserted by dn_route_output_slow() not able to be released and also, it does not wait on the rcu and could potentially cause crash in the path where other users still refer to this dst. This patch makes sure both input and output path do not take dst->__refcnt before calling dn_insert_route() and also makes sure dnrt_free()/dst_free() is called when removing dst from the hash table. The only difference between those 2 calls is that dnrt_free() waits on the rcu while dst_free() does not. Signed-off-by:
Wei Wang <weiwan@google.com> Acked-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Eli Cohen authored
[ Upstream commit 6c780a02 ] Before attempting to initialize the command interface we must wait till the fw_initializing bit is clear. If we fail to meet this condition the hardware will drop our configuration, specifically the descriptors page address. This scenario can happen when the firmware is still executing an FLR flow and did not finish yet so the driver needs to wait for that to finish. Fixes: e3297246 ('net/mlx5_core: Wait for FW readiness on startup') Signed-off-by:
Eli Cohen <eli@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit f8a894b2 ] Now when starting the dad work in addrconf_mod_dad_work, if the dad work is idle and queued, it needs to hold ifa. The problem is there's one gap in [1], during which if the pending dad work is removed elsewhere. It will miss to hold ifa, but the dad word is still idea and queue. if (!delayed_work_pending(&ifp->dad_work)) in6_ifa_hold(ifp); <--------------[1] mod_delayed_work(addrconf_wq, &ifp->dad_work, delay); An use-after-free issue can be caused by this. Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in net6_ifa_finish_destroy was hit because of it. As Hannes' suggestion, this patch is to fix it by holding ifa first in addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if the dad_work is already in queue. Note that this patch did not choose to fix it with: if (!mod_delayed_work(delay)) in6_ifa_hold(ifp); As with it, when delay == 0, dad_work would be scheduled immediately, all addrconf_mod_dad_work(0) callings had to be moved under ifp->lock. Reported-by:
Wei Chen <weichen@redhat.com> Suggested-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit b4846fc3 ] Andrey reported a lockdep warning on non-initialized spinlock: INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 1 PID: 4099 Comm: a.out Not tainted 4.12.0-rc6+ #9 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x292/0x395 lib/dump_stack.c:52 register_lock_class+0x717/0x1aa0 kernel/locking/lockdep.c:755 ? 0xffffffffa0000000 __lock_acquire+0x269/0x3690 kernel/locking/lockdep.c:3255 lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855 __raw_spin_lock_bh ./include/linux/spinlock_api_smp.h:135 _raw_spin_lock_bh+0x36/0x50 kernel/locking/spinlock.c:175 spin_lock_bh ./include/linux/spinlock.h:304 ip_mc_clear_src+0x27/0x1e0 net/ipv4/igmp.c:2076 igmpv3_clear_delrec+0xee/0x4f0 net/ipv4/igmp.c:1194 ip_mc_destroy_dev+0x4e/0x190 net/ipv4/igmp.c:1736 We miss a spin_lock_init() in igmpv3_add_delrec(), probably because previously we never use it on this code path. Since we already unlink it from the global mc_tomb list, it is probably safe not to acquire this spinlock here. It does not harm to have it although, to avoid conditional locking. Fixes: c38b7d32 ("igmp: acquire pmc lock for ip_mc_clear_src()") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit c38b7d32 ] Andrey reported a use-after-free in add_grec(): for (psf = *psf_list; psf; psf = psf_next) { ... psf_next = psf->sf_next; where the struct ip_sf_list's were already freed by: kfree+0xe8/0x2b0 mm/slub.c:3882 ip_mc_clear_src+0x69/0x1c0 net/ipv4/igmp.c:2078 ip_mc_dec_group+0x19a/0x470 net/ipv4/igmp.c:1618 ip_mc_drop_socket+0x145/0x230 net/ipv4/igmp.c:2609 inet_release+0x4e/0x1c0 net/ipv4/af_inet.c:411 sock_release+0x8d/0x1e0 net/socket.c:597 sock_close+0x16/0x20 net/socket.c:1072 This happens because we don't hold pmc->lock in ip_mc_clear_src() and a parallel mr_ifc_timer timer could jump in and access them. The RCU lock is there but it is merely for pmc itself, this spinlock could actually ensure we don't access them in parallel. Thanks to Eric and Long for discussion on this bug. Reported-by:
-
Jia-Ju Bai authored
[ Upstream commit f146e872 ] The kernel may sleep under a rcu read lock in cfpkt_create_pfx, and the function call path is: cfcnfg_linkup_rsp (acquire the lock by rcu_read_lock) cfctrl_linkdown_req cfpkt_create cfpkt_create_pfx alloc_skb(GFP_KERNEL) --> may sleep cfserl_receive (acquire the lock by rcu_read_lock) cfpkt_split cfpkt_create_pfx alloc_skb(GFP_KERNEL) --> may sleep There is "in_interrupt" in cfpkt_create_pfx to decide use "GFP_KERNEL" or "GFP_ATOMIC". In this situation, "GFP_KERNEL" is used because the function is called under a rcu read lock, instead in interrupt. To fix it, only "GFP_ATOMIC" is used in cfpkt_create_pfx. Signed-off-by:
Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by:
-
Krister Johansen authored
[ Upstream commit f186ce61 ] It looks like this: Message from syslogd@flamingo at Apr 26 00:45:00 ... kernel:unregister_netdevice: waiting for lo to become free. Usage count = 4 They seem to coincide with net namespace teardown. The message is emitted by netdev_wait_allrefs(). Forced a kdump in netdev_run_todo, but found that the refcount on the lo device was already 0 at the time we got to the panic. Used bcc to check the blocking in netdev_run_todo. The only places where we're off cpu there are in the rcu_barrier() and msleep() calls. That behavior is expected. The msleep time coincides with the amount of time we spend waiting for the refcount to reach zero; the rcu_barrier() wait times are not excessive. After looking through the list of callbacks that the netdevice notifiers invoke in this path, it appears that the dst_dev_event is the most interesting. The dst_ifdown path places a hold on the loopback_dev as part of releasing the dev associated with the original dst cache entry. Most of our notifier callbacks are straight-forward, but this one a) looks complex, and b) places a hold on the network interface in question. I constructed a new bcc script that watches various events in the liftime of a dst cache entry. Note that dst_ifdown will take a hold on the loopback device until the invalidated dst entry gets freed. [ __dst_free] on DST: ffff883ccabb7900 IF tap1008300eth0 invoked at 1282115677036183 __dst_free rcu_nocb_kthread kthread ret_from_fork Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Mateusz Jurczyk authored
[ Upstream commit defbcf2d ] Verify that the caller-provided sockaddr structure is large enough to contain the sa_family field, before accessing it in bind() and connect() handlers of the AF_UNIX socket. Since neither syscall enforces a minimum size of the corresponding memory region, very short sockaddrs (zero or one byte long) result in operating on uninitialized memory while referencing .sa_family. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by:
-
Mintz, Yuval authored
[ Upstream commit 0eed9cf5 ] Some of the structure's fields are not initialized by the rtnetlink. If driver doesn't set those in ndo_get_vf_config(), they'd leak memory to user. Signed-off-by:
Yuval Mintz <Yuval.Mintz@cavium.com> CC: Michal Schmidt <mschmidt@redhat.com> Reviewed-by:
Greg Rose <gvrose8192@gmail.com> Signed-off-by:
-
Mateusz Jurczyk authored
[ Upstream commit dd0da17b ] Verify that the length of the socket buffer is sufficient to cover the nlmsghdr structure before accessing the nlh->nlmsg_len field for further input sanitization. If the client only supplies 1-3 bytes of data in sk_buff, then nlh->nlmsg_len remains partially uninitialized and contains leftover memory from the corresponding kernel allocation. Operating on such data may result in indeterminate evaluation of the nlmsg_len < sizeof(*nlh) expression. The bug was discovered by a runtime instrumentation designed to detect use of uninitialized memory in the kernel. The patch prevents this and other similar tools (e.g. KMSAN) from flagging this behavior in the future. Signed-off-by:
-
Alexander Potapenko authored
[ Upstream commit c28294b9 ] KMSAN reported a use of uninitialized memory in dev_set_alias(), which was caused by calling strlcpy() (which in turn called strlen()) on the user-supplied non-terminated string. Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Willem de Bruijn authored
commit 00ea1cee upstream. If ip6_dst_lookup_tail has acquired a dst and fails the IPv4-mapped check, release the dst before returning an error. Fixes: ec5e3b0a ("ipv6: Inhibit IPv4-mapped src address on the wire.") Signed-off-by:
Willem de Bruijn <willemb@google.com> Acked-by:
-
- 29 Jun, 2017 24 commits
-
-
Greg Kroah-Hartman authored
-
Guilherme G. Piccoli authored
commit b5a10c5f upstream. Commit 54adc010 ("nvme/quirk: Add a delay before checking for adapter readiness") introduced a quirk to adapters that cannot read the bit NVME_CSTS_RDY right after register NVME_REG_CC is set; these adapters need a delay or else the action of reading the bit NVME_CSTS_RDY could somehow corrupt adapter's registers state and it never recovers. When this quirk was added, we checked ctrl->tagset in order to avoid quirking in probe time, supposing we would never require such delay during probe. Well, it was too optimistic; we in fact need this quirk at probe time in some cases, like after a kexec. In some experiments, after abnormal shutdown of machine (aka power cord unplug), we booted into our bootloader in Power, which is a Linux kernel, and kexec'ed into another distro. If this kexec is too quick, we end up reaching the probe of NVMe adapter in that distro when adapter is in bad state (not fully initialized on our bootloader). What happens next is that nvme_wait_ready() is unable to complete, except if the quirk is enabled. So, this patch removes the original ctrl->tagset verification in order to enable the quirk even on probe time. Fixes: 54adc010 ("nvme/quirk: Add a delay before checking for adapter readiness") Reported-by:
Andrew Byrne <byrneadw@ie.ibm.com> Reported-by:
Jaime A. H. Gomez <jahgomez@mx1.ibm.com> Reported-by:
Zachary D. Myers <zdmyers@us.ibm.com> Signed-off-by:
Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by:
Jeffrey Lien <Jeff.Lien@wdc.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> [mauricfo: backport to v4.4.70 without nvme quirk handling & nvme_ctrl] Signed-off-by:
Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by:
Narasimhan Vaidyanathan <vnarasimhan@in.ibm.com> Signed-off-by:
-
Guilherme G. Piccoli authored
commit 54adc010 upstream. When disabling the controller, the specification says the register NVME_REG_CC should be written and then driver needs to wait the adapter to be ready, which is checked by reading another register bit (NVME_CSTS_RDY). There's a timeout validation in this checking, so in case this timeout is reached the driver gives up and removes the adapter from the system. After a firmware activation procedure, the PCI_DEVICE(0x1c58, 0x0003) (HGST adapter) end up being removed if we issue a reset_controller, because driver keeps verifying the NVME_REG_CSTS until the timeout is reached. This patch adds a necessary quirk for this adapter, by introducing a delay before nvme_wait_ready(), so the reset procedure is able to be completed. This quirk is needed because just increasing the timeout is not enough in case of this adapter - the driver must wait before start reading NVME_REG_CSTS register on this specific device. Signed-off-by:
Jens Axboe <axboe@fb.com> [mauricfo: backport to v4.4.70 without nvme quirk handling & nvme_ctrl] Signed-off-by:
-
Russell King authored
commit 898805e0 upstream. The Marvell driver incorrectly provides phydev->lp_advertising as the logical and of the link partner's advert and our advert. This is incorrect - this field is supposed to store the link parter's unmodified advertisment. This allows ethtool to report the correct link partner auto-negotiation status. Fixes: be937f1f ("Marvell PHY m88e1111 driver fix") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Yendapally Reddy Dhananjaya Reddy authored
commit bb1a6197 upstream. USB PHYs need the MDIO clock divisor enabled earlier to work. Initialize mdio clock divisor in probe function. The ext bus bit available in the same register will be used by mdio mux to enable external mdio. Signed-off-by:
Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver") Reviewed-by:
Jon Mason <jon.mason@broadcom.com> Signed-off-by:
-
William Wu authored
commit b7f73850 upstream. Companion descriptor is only used for SuperSpeed endpoints, if the endpoints are HighSpeed or FullSpeed, the Companion descriptor will not allocated, so we can only access it if gadget is SuperSpeed. I can reproduce this issue on Rockchip platform rk3368 SoC which supports USB 2.0, and use functionfs for ADB. Kernel build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report the following BUG: ================================================================== BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509 Read of size 1 by task swapper/0/0 ============================================================================ BUG kmalloc-256 (Not tainted): kasan: bad access detected ---------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1 alloc_debug_processing+0x128/0x17c ___slab_alloc.constprop.58+0x50c/0x610 __slab_alloc.isra.55.constprop.57+0x24/0x34 __kmalloc+0xe0/0x250 ffs_func_bind+0x52c/0x99c usb_add_function+0xd8/0x1d4 configfs_composite_bind+0x48c/0x570 udc_bind_to_driver+0x6c/0x170 usb_udc_attach_driver+0xa4/0xd0 gadget_dev_desc_UDC_store+0xcc/0x118 configfs_write_file+0x1a0/0x1f8 __vfs_write+0x64/0x174 vfs_write+0xe4/0x200 SyS_write+0x68/0xc8 el0_svc_naked+0x24/0x28 INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247 ... Call trace: [<ffffff900808aab4>] dump_backtrace+0x0/0x230 [<ffffff900808acf8>] show_stack+0x14/0x1c [<ffffff90084ad420>] dump_stack+0xa0/0xc8 [<ffffff90082157cc>] print_trailer+0x188/0x198 [<ffffff9008215948>] object_err+0x3c/0x4c [<ffffff900821b5ac>] kasan_report+0x324/0x4dc [<ffffff900821aa38>] __asan_load1+0x24/0x50 [<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0 [<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8 [<ffffff90089d7394>] android_setup+0x124/0x1a0 [<ffffff90089acd18>] _setup+0x54/0x74 [<ffffff90089b6b98>] handle_ep0+0x3288/0x4390 [<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4 [<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298 [<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20 [<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac [<ffffff9008116610>] handle_irq_event+0x60/0xa0 [<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4 [<ffffff9008115568>] generic_handle_irq+0x30/0x40 [<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc [<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4 ... Memory state around the buggy address: ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc >ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00 ================================================================== Signed-off-by:
William Wu <william.wu@rock-chips.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by:
-
Michael Ellerman authored
[Note this patch is not upstream. The bug fix was fixed differently in upstream prior to the bug being identified.] The SLB miss handler calls slb_allocate_realmode() in order to create an SLB entry for the faulting address. At the very start of that function we check that the faulting Effective Address (EA) is less than PGTABLE_RANGE (ignoring the region), ie. is it an address which could possibly fit in the virtual address space. For an EA which fails that test, we branch out of line (to label 8), but we still go on to create an SLB entry for the address. The SLB entry we create has a VSID of 0, which means it will never match anything in the hash table and so can't actually translate to a physical address. However that SLB entry will be inserted in the SLB, and so needs to be managed properly like any other SLB entry. In particular we need to insert the SLB entry in the SLB cache, so that it will be flushed when the process is descheduled. And that is where the bugs begin. The first bug is that slb_finish_load() uses cr7 to decide if it should insert the SLB entry into the SLB cache. When we come from the invalid EA case we don't set cr7, it just has some junk value from userspace. So we may or may not insert the SLB entry in the SLB cache. If we fail to insert it, we may then incorrectly leave it in the SLB when the process is descheduled. The second bug is that even if we do happen to add the entry to the SLB cache, we do not have enough bits in the SLB cache to remember the full ESID value for very large EAs. For example if a process branches to 0x788c545a18000000, that results in a 256MB SLB entry with an ESID of 0x788c545a1. But each entry in the SLB cache is only 32-bits, meaning we truncate the ESID to 0x88c545a1. This has the same effect as the first bug, we incorrectly leave the SLB entry in the SLB when the process is descheduled. When a process accesses an invalid EA it results in a SEGV signal being sent to the process, which typically results in the process being killed. Process death isn't instantaneous however, the process may catch the SEGV signal and continue somehow, or the kernel may start writing a core dump for the process, either of which means it's possible for the process to be preempted while its processing the SEGV but before it's been killed. If that happens, when the process is scheduled back onto the CPU we will allocate a new SLB entry for the NIP, which will insert a second entry into the SLB for the bad EA. Because we never flushed the original entry, due to either bug one or two, we now have two SLB entries that match the same EA. If another access is made to that EA, either by the process continuing after catching the SEGV, or by a second process accessing the same bad EA on the same CPU, we will trigger an SLB multi-hit machine check exception. This has been observed happening in the wild. The fix is when we hit the invalid EA case, we mark the SLB cache as being full. This causes us to not insert the truncated ESID into the SLB cache, and means when the process is switched out we will flush the entire SLB. Note that this works both for the original fault and for a subsequent call to slb_allocate_realmode() from switch_slb(). Because we mark the SLB cache as full, it doesn't really matter what value is in cr7, but rather than leaving it as something random we set it to indicate the address was a kernel address. That also skips the attempt to insert it in the SLB cache which is a nice side effect. Another way to fix the bug would be to make the entries in the SLB cache wider, so that we don't truncate the ESID. However this would be a more intrusive change as it alters the size and layout of the paca. This bug was fixed in upstream by commit f0f558b1 ("powerpc/mm: Preserve CFAR value on SLB miss caused by access to bogus address"), which changed the way we handle a bad EA entirely removing this bug in the process. Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Reviewed-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Joël Esponde authored
commit 807c1625 upstream. With the S25FL127S nor flash part, each writing to the configuration register takes hundreds of ms. During that time, no more accesses to the flash should be done (even reads). This commit adds a wait loop after the register writing until the flash finishes its work. This issue could make rootfs mounting fail when the latter was done too much closely to this quad enable bit setting step. And in this case, a driver as UBIFS may try to recover the filesystem and may broke it completely. Signed-off-by:
Joël Esponde <joel.esponde@honeywell.com> Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by:
-
Tobias Wolf authored
commit 3ec75441 upstream. An empty __dtb_start to __dtb_end section might result in initial_boot_params being null for arch/mips/ralink. This showed that the boot process hangs indefinitely in of_scan_flat_dt(). Signed-off-by:
Tobias Wolf <dev-NTEO@vplace.de> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14605/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
David Howells authored
commit 5f2f9765 upstream. This fixes CVE-2017-7482. When a kerberos 5 ticket is being decoded so that it can be loaded into an rxrpc-type key, there are several places in which the length of a variable-length field is checked to make sure that it's not going to overrun the available data - but the data is padded to the nearest four-byte boundary and the code doesn't check for this extra. This could lead to the size-remaining variable wrapping and the data pointer going over the end of the buffer. Fix this by making the various variable-length data checks use the padded length. Reported-by:
石磊 <shilei-c@360.cn> Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Marc Dionne <marc.c.dionne@auristor.com> Reviewed-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Johan Hovold authored
commit ec963b41 upstream. Fix up the root-hub descriptor to accommodate the variable-length DeviceRemovable and PortPwrCtrlMask fields, while marking all ports as removable (and leaving the reserved bit zero unset). Also add a build-time constraint on VHCI_HC_PORTS which must never be greater than USB_MAXCHILDREN (but this was only enforced through a KConfig constant). This specifically fixes the descriptor layout whenever VHCI_HC_PORTS is greater than seven (default is 8). Fixes: 04679b34 ("Staging: USB/IP: add client driver") Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net> Cc: Valentina Manea <valentina.manea.m@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Acked-by:
Shuah Khan <shuahkh@osg.samsung.com> [ johan: backport to v4.4, which uses VHCI_NPORTS ] Signed-off-by:
-
Alex Deucher authored
commit 52b482b0 upstream. Increase the default display clock on newer asics to accomodate some high res modes with really high refresh rates. bug: https://bugs.freedesktop.org/show_bug.cgi?id=93826Acked-by:
Chunming Zhou <david1.zhou@amd.com> Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 05b4017b upstream. We were using the wrong structure which lead to an overflow on some boards. bug: https://bugs.freedesktop.org/show_bug.cgi?id=101387Acked-by:
-
Alex Deucher authored
commit acfd6ee4 upstream. Fixes resume from suspend. bug: https://bugzilla.kernel.org/show_bug.cgi?id=196121Reported-by:
Przemek <soprwa@gmail.com> Signed-off-by:
-
Alex Deucher authored
commit 4eb59793 upstream. Disable PX on these systems. bug: https://bugs.freedesktop.org/show_bug.cgi?id=101491Signed-off-by:
-
Nicholas Bellinger authored
commit abb85a9b upstream. When iscsi WRITE underflow occurs there are two different scenarios that can happen. Normally in practice, when an EDTL vs. SCSI CDB TRANSFER LENGTH underflow is detected, the iscsi immediate data payload is the smaller SCSI CDB TRANSFER LENGTH. That is, when a host fabric LLD is using a fixed size EDTL for a specific control CDB, the SCSI CDB TRANSFER LENGTH and actual SCSI payload ends up being smaller than EDTL. In iscsi, this means the received iscsi immediate data payload matches the smaller SCSI CDB TRANSFER LENGTH, because there is no more SCSI payload to accept beyond SCSI CDB TRANSFER LENGTH. However, it's possible for a malicous host to send a WRITE underflow where EDTL is larger than SCSI CDB TRANSFER LENGTH, but incoming iscsi immediate data actually matches EDTL. In the wild, we've never had a iscsi host environment actually try to do this. For this special case, it's wrong to truncate part of the control CDB payload and continue to process the command during underflow when immediate data payload received was larger than SCSI CDB TRANSFER LENGTH, so go ahead and reject and drop the bogus payload as a defensive action. Note this potential bug was originally relaxed by the following for allowing WRITE underflow in MSFT FCP host environments: commit c72c5250 Author: Roland Dreier <roland@purestorage.com> Date: Wed Jul 22 15:08:18 2015 -0700 target: allow underflow/overflow for PR OUT etc. commands Cc: Roland Dreier <roland@purestorage.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 73d4e580 upstream. This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED when a fabric driver drops it's second reference from below the target_core_tmr.c based callers of transport_cmd_finish_abort(). Recently with the conversion of kref to refcount_t, this bug was manifesting itself as: [705519.601034] refcount_t: underflow; use-after-free. [705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs [705539.719111] ------------[ cut here ]------------ [705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51 Since the original kref atomic_t based kref_put() didn't check for underflow and only invoked the final callback when zero was reached, this bug did not manifest in practice since all se_cmd memory is using preallocated tags. To address this, go ahead and propigate the existing return from transport_put_cmd() up via transport_cmd_finish_abort(), and change transport_cmd_finish_abort() + core_tmr_handle_tas_abort() callers to only do their local target_put_sess_cmd() if necessary. Reported-by:
Bart Van Assche <bart.vanassche@sandisk.com> Tested-by:
Gary Guo <ghg@datera.io> Tested-by:
Chu Yuan Lin <cyl@datera.io> Signed-off-by:
-
John Stultz authored
commit ceea5e37 upstream. In tests, which excercise switching of clocksources, a NULL pointer dereference can be observed on AMR64 platforms in the clocksource read() function: u64 clocksource_mmio_readl_down(struct clocksource *c) { return ~(u64)readl_relaxed(to_mmio_clksrc(c)->reg) & c->mask; } This is called from the core timekeeping code via: cycle_now = tkr->read(tkr->clock); tkr->read is the cached tkr->clock->read() function pointer. When the clocksource is changed then tkr->clock and tkr->read are updated sequentially. The code above results in a sequential load operation of tkr->read and tkr->clock as well. If the store to tkr->clock hits between the loads of tkr->read and tkr->clock, then the old read() function is called with the new clock pointer. As a consequence the read() function dereferences a different data structure and the resulting 'reg' pointer can point anywhere including NULL. This problem was introduced when the timekeeping code was switched over to use struct tk_read_base. Before that, it was theoretically possible as well when the compiler decided to reload clock in the code sequence: now = tk->clock->read(tk->clock); Add a helper function which avoids the issue by reading tk_read_base->clock once into a local variable clk and then issue the read function via clk->read(clk). This guarantees that the read() function always gets the proper clocksource pointer handed in. Since there is now no use for the tkr.read pointer, this patch also removes it, and to address stopping the fast timekeeper during suspend/resume, it introduces a dummy clocksource to use rather then just a dummy read function. Signed-off-by:
John Stultz <john.stultz@linaro.org> Acked-by:
Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Daniel Mentz <danielmentz@google.com> Link: http://lkml.kernel.org/r/1496965462-20003-2-git-send-email-john.stultz@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Daniel Drake authored
commit 817ae460 upstream. Without this quirk, the touchpad is not responsive on this product, with the following message repeated in the logs: psmouse serio1: bad data from KBC - timeout Add it to the notimeout list alongside other similar Fujitsu laptops. Signed-off-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Naveen N. Rao authored
commit a9f8553e upstream. This fixes a crash when function_graph and jprobes are used together. This is essentially commit 237d28db ("ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing"), but for powerpc. Jprobes breaks function_graph tracing since the jprobe hook needs to use jprobe_return(), which never returns back to the hook, but instead to the original jprobe'd function. The solution is to momentarily pause function_graph tracing before invoking the jprobe hook and re-enable it when returning back to the original jprobe'd function. Fixes: 6794c782 ("powerpc64: port of the function graph tracer") Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Eric W. Biederman authored
commit 57db7e4a upstream. Thomas Gleixner wrote: > The CRIU support added a 'feature' which allows a user space task to send > arbitrary (kernel) signals to itself. The changelog says: > > The kernel prevents sending of siginfo with positive si_code, because > these codes are reserved for kernel. I think we can allow a task to > send such a siginfo to itself. This operation should not be dangerous. > > Quite contrary to that claim, it turns out that it is outright dangerous > for signals with info->si_code == SI_TIMER. The following code sequence in > a user space task allows to crash the kernel: > > id = timer_create(CLOCK_XXX, ..... signo = SIGX); > timer_set(id, ....); > info->si_signo = SIGX; > info->si_code = SI_TIMER: > info->_sifields._timer._tid = id; > info->_sifields._timer._sys_private = 2; > rt_[tg]sigqueueinfo(..., SIGX, info); > sigemptyset(&sigset); > sigaddset(&sigset, SIGX); > rt_sigtimedwait(sigset, info); > > For timers based on CLOCK_PROCESS_CPUTIME_ID, CLOCK_THREAD_CPUTIME_ID this > results in a kernel crash because sigwait() dequeues the signal and the > dequeue code observes: > > info->si_code == SI_TIMER && info->_sifields._timer._sys_private != 0 > > which triggers the following callchain: > > do_schedule_next_timer() -> posix_cpu_timer_schedule() -> arm_timer() > > arm_timer() executes a list_add() on the timer, which is already armed via > the timer_set() syscall. That's a double list add which corrupts the posix > cpu timer list. As a consequence the kernel crashes on the next operation > touching the posix cpu timer list. > > Posix clocks which are internally implemented based on hrtimers are not > affected by this because hrtimer_start() can handle already armed timers > nicely, but it's a reliable way to trigger the WARN_ON() in > hrtimer_forward(), which complains about calling that function on an > already armed timer. This problem has existed since the posix timer code was merged into 2.5.63. A few releases earlier in 2.5.60 ptrace gained the ability to inject not just a signal (which linux has supported since 1.0) but the full siginfo of a signal. The core problem is that the code will reschedule in response to signals getting dequeued not just for signals the timers sent but for other signals that happen to a si_code of SI_TIMER. Avoid this confusion by testing to see if the queued signal was preallocated as all timer signals are preallocated, and so far only the timer code preallocates signals. Move the check for if a timer needs to be rescheduled up into collect_signal where the preallocation check must be performed, and pass the result back to dequeue_signal where the code reschedules timers. This makes it clear why the code cares about preallocated timers. Reported-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Sebastian Parschauer authored
commit 3db28271 upstream. This mouse is also known under other IDs. It needs the quirk ALWAYS_POLL or will disconnect in runlevel 1 or 3. Signed-off-by:
Sebastian Parschauer <sparschauer@suse.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Pavel Shilovsky authored
commit dcd87838 upstream. Downgrade the loglevel for SMB2 to prevent filling the log with messages if e.g. readdir was interrupted. Also make SMB2 and SMB1 codepaths do the same logging during readdir. Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Paul Mackerras authored
commit 46a704f8 upstream. If userspace attempts to call the KVM_RUN ioctl when it has hardware transactional memory (HTM) enabled, the values that it has put in the HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by guest values. To fix this, we detect this condition and save those SPR values in the thread struct, and disable HTM for the task. If userspace goes to access those SPRs or the HTM facility in future, a TM-unavailable interrupt will occur and the handler will reload those SPRs and re-enable HTM. If userspace has started a transaction and suspended it, we would currently lose the transactional state in the guest entry path and would almost certainly get a "TM Bad Thing" interrupt, which would cause the host to crash. To avoid this, we detect this case and return from the KVM_RUN ioctl with an EINVAL error, with the KVM exit reason set to KVM_EXIT_FAIL_ENTRY. Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by:
-
