- 02 May, 2010 13 commits
-
-
Vikas Chaudhary authored
* Handles SCSI command aborts. * Serialization srb between error handler and command completion path. Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
Ravi Anand <ravi.anand@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Vikas Chaudhary authored
used cmd->host_scribble to store iocb command handle. Signed-off-by:
-
Vikas Chaudhary authored
Per RFC 3720, Login Response Status Code 0x02 should not be retried. Condensed connection error checking code to a single routine, and added check for status class 0x02. Signed-off-by:
Karen Higgins <karen.higgins@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Updated firmware ready timeout algorithm to prevent long delays and use jiffies to time out instead of counter. Also use msleep_interruptible instead of msleep. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Link Down -> Mark all devices missing Previously, the driver took no action on a Link Down, and waited for the I/O on a dead connection to timeout in the firmware before marking the DDB missing. Link Up -> Mark all devices online F/W will do auto login to all the devices only once. After that its the responsibility of the driver to relogin to devices whenever there is : * Any sort of connection failure or * KATO expires indicating target has logged out or * I/O times out etc. Signed-off-by: -
Vikas Chaudhary authored
Signed-off-by:
-
Roland Dreier authored
If cxgb3i_pdu_init() fails, then it appears that cxgb3i_iscsi_init() will not be cleaned up, leading to the iscsi transport being left registered. Fix this by adding a call to cxgb3i_iscsi_cleanup() on the error path. Signed-off-by:
Roland Dreier <rolandd@cisco.com> Reviewed-by:
-
Tom Rini authored
The scsi/scsi.h header is normally provided by the libc (and was not exported by the kernel since 2.6.24) and has been until it was re-exported with 2.6.31. The kernel version is not userspace clean and does not appear to provide anything useable in userland over the (e)glibc version. Signed-off-by:
Tom Rini <tom_rini@mentor.com> Signed-off-by:
-
Dan Carpenter authored
In the original code we dereferenced "pm8001_dev" before checking if it was null. This patch moves the dereference inside the condition. This was found by a static checker (smatch). I looked, but I couldn't tell if "pm8001_dev" dev was ever actually null. The approach in this patch seemed like the safest response. Signed-off-by:
Dan Carpenter <error27@gmail.com> Acked-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
-
Brian King authored
If a command times out resulting in EH getting invoked, we wait for the aborted commands to come back after sending the abort. Shorten the amount of time we wait for these responses, to ensure we don't get stuck in EH for several minutes. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
Commands which are completed by the VIOS are placed on a CRQ in kernel memory for the ibmvfc driver to process. Each CRQ entry is 16 bytes. The ibmvfc driver reads the first 8 bytes to check if the entry is valid, then reads the next 8 bytes to get the handle, which is a pointer the completed command. This fixes an issue seen on Power 7 where the processor reordered the loads from memory, resulting in processing command completion with a stale handle. This could result in command timeouts, and also early completion of commands. Signed-off-by:
-
Mike Miller authored
This patch removes unnecessary #define's from hpsa. The SCSI midlayer handles all this for us. Signed-off-by:
Mike Miller <mike.miller@hp.com> Signed-off-by:
-
- 01 May, 2010 3 commits
-
-
Tomohiro Kusumi authored
This patch fixes sdev_rw_attr() macro for scsi device sysfs entries. It seems there is no such function snscanf in the current linux kernel, so it fails to compile scsi driver when someone try to add a new rw entry. This has been unfixed for a long time probably because current scsi device has no rw entries. # grep snscanf . -rn ./drivers/scsi/scsi_sysfs.c:489: snscanf (buf, 20, format_string, &sdev->field); \ Signed-off-by:
Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com> Signed-off-by:
-
Jing Huang authored
Fix the compilation warning in powerpc. The same change also fixes endian issue we found in powerpc test. This patch has been tested in x86 and powerpc platform. it is created using scsi-misc-2.6. Signed-off-by:
Jing Huang <huangj@brocade.com> Signed-off-by:
-
Giridhar Malavali authored
Enhanced the driver to support new FCoE host bus adapter. Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
- 30 Apr, 2010 5 commits
-
-
Martin K. Petersen authored
Various SCSI trace enhancements: - Display data and protection information scatterlist lengths in the trace output - Add support for VERIFY and WRITE SAME commands and decode the UNMAP bit if applicable - Add decoding of the PROTECT field for READ/VERIFY/WRITE/WRITE SAME commands as well as the EXPECTED INITIAL REFERENCE TAG field for their 32-byte variants - Decode READ CAPACITY(16), GET LBA STATUS, and UNMAP Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Kei Tokunaga authored
Signed-off-by:
Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by:
Kei Tokunaga <tokunaga.keiich@jp.fujitsu.com> Signed-off-by:
-
Kei Tokunaga authored
__print_hex() prints values in an array in hex (w/o '0x') (space separated) EX) 92 33 32 f3 ee 4d Signed-off-by:
Li Zefan <lizf@cn.fujitsu.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Martin K. Petersen authored
Add definitions for VERIFY(12) and VERIFY(32). Signed-off-by:
-
Martin K. Petersen authored
Add a few clarifying comments in the B0 page function and allow the optimal transfer length field to be specified on the command line using opt_blks=N. Signed-off-by:
-
- 11 Apr, 2010 19 commits
-
-
Srinivas authored
This patch adds a bunch of fixes 1. Reduce sg table size to 64 (SG_MX) instead of default SG_ALL 2. clear task lists on phy down events 3. release all tasks on port deformation 4. release current task for device gone notification 5. Add sata abort handing 6. Add 10ms delay to each port reset (currently done serially and with interrupts disabled) [jejb: whitespace fixes and clean ups plus added description added dummy 94xx_clear_srs_irq function just to prevent the mismatch in the mvs_dispatch structure killing 94xx cards] Signed-off-by:Srinivas <satyasrinivasp@hcl.in> Cc: Andy Yan <ayan@marvell.com> Cc: qswang@marvell.com Cc: jfeng@marvell.com Signed-off-by:
-
Avi Kaplan authored
iscsi_conn is not used so remove it from iscsi_sw_tcp_conn. Signed-off-by:
Avi Kaplan <savik751@gmail.com> Signed-off-by:
-
Avi Kaplan authored
This patch changes the arguments to iscsi_sw_tcp_conn_restore_callbacks, so that it works like the function to set the callbacks and because in upcoming patches we need a iscsi_conn. Signed-off-by:
-
Mike Christie authored
blk_get_request sets the cmd_flags, so we should not and do not need to set them. If we did set them to a different value then it can cause a oops in the elevator code. Signed-off-by:
-
Dan Carpenter authored
This change is basically a clean up. datadgst_en is an int which comes from the user. I didn't see anything limiting it to 1 and 0 although obviously that's what it's supposed to be. If the user passed in 2 this test would fail. This same if condition is repeated in another function and it uses && there. Signed-off-by:
-
Chris Leech authored
Print all world wide node names (node, port and fabric) with the same format specifier of "%16.16llx". That makes sure they all print as a 16 character hex string, with lower case letters, no 0x prefix, and without stripping off any leading 0s. Signed-off-by:
Chris Leech <christopher.leech@intel.com> Signed-off-by:
Robert Love <robert.w.love@intel.com> Signed-off-by:
-
Chris Leech authored
Most of the prints of fabric IDs were specified as %6x, which will not print any leading 0s. It's nice to see leading 0s for identifiers like this, which are a fixed length. This patch sets the precision modifier as well, making the specifier %6.6x, which forces the printing of leading 0s. Signed-off-by:
-
Yi Zou authored
fc_fcp_resp is assuming when FCP_SNS_LEN_VAL is set, the FCP_RSP_LEN_VAL is not, which is not true. This leads to not copying the sense data and error out a valid FCP_RSP. Signed-off-by:
Yi Zou <yi.zou@intel.com> Signed-off-by:
-
Vasu Dev authored
No reason to restrict CDB size to 12 bytes in fcoe, so increased to 16 so that 16 bytes SCSI CDB doesn't fail. Uses common define to set max_cmd_len for fcoe and fnic, fnic is already setting max_cmd_len to 16. sg_readcap -l fails without this fix. Signed-off-by:
Vasu Dev <vasu.dev@intel.com> Signed-off-by:
-
Vasu Dev authored
Signed-off-by:
-
Brian Uchino authored
fnic_flush_tx() is used to send frames held while fabric login is in progress. The frames are held in tx_queue, but fnic_flush_tx() was incorrectly flushing from recv_queue which is used for received frames. Signed-off-by:
Brian Uchino <buchino@cisco.com> Signed-off-by:
Abhijeet Joglekar <abjoglek@cisco.com> Signed-off-by:
-
Brian Uchino authored
New fnic version to mark inclusion of tx_flush bugfix. Signed-off-by:
-
Joe Eykholt authored
hton24(p + 3, value) would fail to compile because p + 3[0] is not a valid expression. Went ahead and converted hton24 and ntoh24 to inline functions, which is better because the parameters are evalutated only once. Signed-off-by:
Joe Eykholt <jeykholt@cisco.com> Signed-off-by:
-
Joe Eykholt authored
fc_exch_recv_req has variables eof, sof, and f_ctl, which are set but never used. Delete them. Signed-off-by:
-
Chris Leech authored
Allow for dormant states while link configuration completes. In the default link mode, this is equivalent to the old check. Signed-off-by:
-
Chris Leech authored
The FIP controler state wasn't being reset on a disable. A disable/enable sequence should be treated as a link event. Otherwise, when using disable to mask a time when the link is up but unusable, FCF discovery would attempt to continue and login would jump directly to the non-FIP fallback on enable. Signed-off-by:
-
Robert Love authored
FPMA indicates that the Fabric will provide the host's N_Port's MAC address. When sending a FLOGI/FDISC frame and FPMA was negotiated through FIP discovery we still need to provide the MAC descriptor, as per the specification, but the MAC should be zero'd out since the FCF will be providing it in the FLOGI/FDISC ACC. In FC-BB-5 section 7.8.7.4.2 (Fabric login) it states: The MAC address field in the MAC address descriptor of a FIP FLOGI Request operation or a FIP NPIV FDISC Request operation shall contain: a) the proposed MAC address to use as VN_Port MAC address if the ENode is requesting to use SPMA (see table 27); b) all zeroes to indicate no MAC address is proposed if the ENode is requesting to use FPMA (see table 27); or c) the proposed MAC address to use as VN_Port MAC address if the ENode supports both SPMA and FPMA and leaves the decision of which addressing scheme to use to the FCF (i.e., if both the FP and SP bits are set to one, see table 27). This patch fixes case B. This patch also adds debug statements to illustrate whether a FPMA or SPMA MAC is added to a FLOGI/FDISC frame. Signed-off-by:
-
Kashyap, Desai authored
Upgrade version to 05.100.00.02 Signed-off-by:
Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by:
-
Kashyap, Desai authored
Fix a oops in _scsih_sas_device_remove. The driver was attempting to delete a object from the sas_device link list when the object was not present. Added sanity check for sas_device NULL dereference. before deleting sas_device now driver will search device in list then only it will follow device removal. Signed-off-by:
-
