sk->sk_rx_queue_mapping can be modified locklessly,
add a couple of READ_ONCE()/WRITE_ONCE() to document this fact.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sk_rx_queue_mapping is located in a cache line that should be kept read mostly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sk_napi_id is located in a cache line that can be kept read mostly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Increase cache locality by moving rx_dst_coookie next to sk->sk_rx_dst

This removes one or two cache line misses in IPv6 early demux (TCP/UDP)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Increase cache locality by moving rx_dst_ifindex next to sk->sk_rx_dst

This is part of an effort to reduce cache line misses in TCP fast path.

This removes one cache line miss in early demux.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

rx_dropped, tx_dropped, rx_frame_errors and rx_crc_errors are being
wrongly fetched from the target container rather than source percpu
ones.
No idea if that goes from the vendor driver or was brainoed during
the refactoring, but fix it either way.

Fixes: a97c69ba ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20211023121148.113466-1-alobakin@pm.meSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
bluetooth: don't write directly to netdev->dev_addr

The usual conversions.
====================

Link: https://lore.kernel.org/r/20211022231834.2710245-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.

Convert bluetooth from memcpy(... ETH_ADDR) to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, ETH_ALEN)
  + eth_hw_addr_set(dev, np)
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

hw_addr is a uint AKA unsigned int. dev_addr_set() takes
a u8 *.

  drivers/net/fddi/defza.c:1383:27: error: passing argument 2 of 'dev_addr_set' from incompatible pointer type [-Werror=incompatible-pointer-types]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1e9258c3 ("fddi: defxx,defza: use dev_addr_set()")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/20211025160000.2803818-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

AES_CCM_128 and CHACHA20_POLY1305 are already supported by tls,
similar to setsockopt, getsockopt also needs to support these
two algorithms.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tls already supports the SM4 GCM/CCM algorithms. It is also necessary
to add support for these two algorithms in tls_crypto_context to avoid
potential issues caused by forced type conversion.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid
some open-coded arithmetic in allocator arguments.

Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

In the case of catc we need a new temporary buffer to conform
to the rules for DMA coherency. That in turn necessitates
a reworking of error handling in probe().
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2021-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.16

Third set of patches for v5.16. This time we have a small one to
quickly fix two mt76 build failures I had missed in my previous pull
request.

Major changes:

mt76

* fix linking when CONFIG_MMC is disabled

* fix dev_err() format warning

* mt7615: mt7622: fix ibss and meshpoint
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeroen de Borst says:

====================
gve: Add jumbo-frame support for GQ

This patchset introduces jumbo-frame support for the GQ queue format.
The device already supports jumbo-frames on TX. This introduces
multi-descriptor RX packets using a packet continuation bit.

A widely deployed driver has a bug with causes it to fail to load
when a MTU greater than 2048 bytes is configured. A jumbo-frame device
option is introduced to pass a jumbo-frame MTU only to drivers that
support it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A widely deployed driver has a bug that will cause the driver not
to load when a max_mtu > 2048 is present in the device descriptor.

To avoid this bug while still enabling jumbo frames, we present a lower
max_mtu in the device descriptor and pass the actual max_mtu in
a separate device option.

The driver supports 2 different queue formats. To enable features
on one queue format, but not the other, a supported_features mask
was added to the device options in the device descriptor.
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This enables the driver to receive RX packets spread across multiple
buffers:

For a given multi-fragment packet the "packet continuation" bit is set
on all descriptors except the last one. These descriptors' payloads are
combined into a single SKB before the SKB is handed to the
networking stack.

This change adds a "packet buffer size" notion for RX queues. The
CreateRxQueue AdminQueue command sent to the device now includes the
packet_buffer_size.

We opt for a packet_buffer_size of PAGE_SIZE / 2 to give the
driver the opportunity to flip pages where we can instead of copying.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This refactor moves the skb_head and skb_tail fields into a new
gve_rx_ctx struct. This new struct will contain information about the
current packet being processed. This is in preparation for
multi-descriptor RX packets.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: mlxsw: Various updates

This patchset contains various updates to mlxsw selftests.

Patch #1 replaces open-coded compatibility checks with dedicated
helpers. These helpers are used to skip tests when run on incompatible
machines.

Patch #2 avoids spurious failures in some tests by using permanent
neighbours instead of reachable ones.

Patch #3 reduces the run time of a test by not iterating over all the
available trap policers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of iterating over all the available trap policers, only perform
the tests with three policers: The first, the last and the one in the
middle of the range. On a Spectrum-3 system, this reduces the run time
from almost an hour to a few minutes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The nexthop objects tests configure dummy reachable neighbours so that
the nexthops will have a MAC address and be programmed to the device.

Since these are dummy reachable neighbours, they can be transitioned by
the kernel to a failed state if they are around for too long. This can
happen, for example, if the "TIMEOUT" variable is configured with a too
high value.

Make the tests more robust by configuring the neighbours as permanent,
so that the tests do not depend on the configured timeout value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of mlxsw-specific selftests currently detect whether they are run
on a compatible machine, and bail out silently when not. These tests are
however done in a somewhat impenetrable manner by directly comparing PCI
IDs against a blacklist or a whitelist, and bailing out silently if the
machine is not compatible.

Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying
the supported machines in a human-readable manner. If the current machine
is incompatible, the helper emits a SKIP message and returns an error code,
based on which the caller can gracefully bail out in a suitable way. This
allows a more readable conditions such as:

	mlxsw_only_on_spectrum 2+ || return

Convert all existing open-coded guards to the new helper. Also add two new
guards to do_mark_test() and do_drop_test(), which are supported only on
Spectrum-2+, but the corresponding check was not there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luo Jie says:

====================
net: phy: Add qca8081 ethernet phy driver

This patch series add the qca8081 ethernet phy driver support, which
improve the wol feature, leverage at803x phy driver and add the fast
retrain, master/slave seed and CDT feature.

Changes in v7:
	* update Reviewed-by tags.

Changes in v6:
	* add Reviewed-by tags on the applicable patches.

Changes in v5:
	* rebase the patches on net-next/master.

Changes in v4:
	* handle other interrupts in set_wol.
	* add genphy_c45_fast_retrain.

Changes in v3:
	* correct a typo "excpet".
	* remove the suffix "PHY" from phy name.

Changes in v2:
	* add definitions of fast retrain related registers in mdio.h.
	* break up the patch into small patches.
	* improve the at803x legacy code.

Changes in v1:
	* merge qca8081 phy driver into at803x.
	* add cdt feature.
	* leverage at803x phy driver helpers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To perform CDT of qca8081 phy:
1. disable hibernation.
2. force phy working in MDI mode.
3. force phy working in 1000BASE-T mode.
4. configure the related thresholds.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. The master/slave seed needs to be updated when the link can't
be created.

2. The case where two qca8081 PHYs are connected each other and
master/slave seed is generated as the same value also needs
to be considered, so adding this code change into read_status
instead of link_change_notify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

qca8081 phy is a single port phy, configure
phy the lower seed value to make it linked as slave
mode easier.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the qca8081 phy driver config_init function, which includes:
1. Enable fast restrain.
2. Add 802.3az configurations.
3. Initialize ADC threshold as 100mv.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add generic fast retrain auto-negotiation function for C45 PHYs.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the constants for 2.5G fast retrain capability
in 10G AN control register, fast retrain status and
control register and THP bypass register into mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reuse at803x phy driver config_aneg excepting
adding 2500M auto-negotiation.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reuse the at803x phy driver get_features excepting
adding 2500M capability.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Separate the function at803x_read_specific_status from
the at803x_read_status, since it can be reused by the
read_status of qca8081 phy driver excepting adding the
2500M speed.

2. Add the qca8081 read_status function qca808x_read_status.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

qca8081 is a single port ethernet phy chip that supports
10/100/1000/2500 Mbps mode.

Add the basic phy driver features, and reuse the at803x
phy driver functions.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use GENMASK() for the current speed value.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wol feature is controlled by the MMD3.8012 bit5,
need to set this bit when the wol function is enabled.

The reg18 bit0 is for enabling WOL interrupt, when wol
occurs, the wol interrupt status reg19 bit0 is set to 1.

Call phy_trigger_machine if there are any other interrupt
pending in the function set_wol.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert at803x_set_wol to use phy_modify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guangbin Huang says:

====================
net: hns3: updates for -next

This series includes some updates for the HNS3 ethernet driver.

      for it.
      off.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds himac error recovery module, link_error type and
ptp_error type for himac.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>