- 17 Jun, 2009 40 commits
-
-
Philipp Zabel authored
This enables the ASIC3's SD/SDIO MFD cell, supported by the tmio_mmc driver. Signed-off-by:
Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com>
-
Philipp Zabel authored
This enables the ASIC3's DS1WM MFD cell, supported by the ds1wm driver. Signed-off-by:
-
Philipp Zabel authored
Only the base addresses remain, as they are needed to set up the IOMEM resources. Signed-off-by:
-
Philipp Zabel authored
This should make the code a little bit easier to read. Signed-off-by:
-
Philipp Zabel authored
IRQ number definitions for PWM, LED, SPI and OWM (ds1wm). Signed-off-by:
-
Philipp Zabel authored
Since ASIC3 has to work on both PXA and S3C and since their struct clk implementations differ, we can't register out clocks with the clkdev mechanism (yet?). For now we have to keep clock handling internal to this driver and enable/disable the clocks via the mfd_cell->enable/disable functions. Signed-off-by:
-
Philipp Zabel authored
Used to configure single bits of the SDHWCTRL_SDCONF and EXTCF_RESET/SELECT registers needed for DS1WM, MMC/SDIO and PCMCIA functionality. Signed-off-by:
-
Mark Brown authored
More with the grammar. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Daniel Ribeiro authored
The PCAP Asic as present on EZX phones is a multi function device with voltage regulators, ADC, touch screen controller, RTC, USB transceiver, leds controller, and audio codec. It has two SPI ports, typically one is connected to the application processor and another to the baseband, this driver provides read/write functions to its registers, irq demultiplexer and ADC queueing/abstraction. This chip is used on a lot of Motorola phones, it was manufactured by TI as a custom product with the name PTWL93017, later this design evolved into the ATLAS PMIC from Freescale (MC13783). Signed-off-by:
Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by:
-
Linus Walleij authored
This adds a core driver for the AB3100 mixed-signal circuit found in the ST-Ericsson U300 series platforms. This driver is a singleton proxy for all accesses to the AB3100 sub-drivers which will be merged on top of this one, RTC, regulators, battery and system power control, vibrator, LEDs, and an ALSA codec. Signed-off-by:
Linus Walleij <linus.walleij@stericsson.com> Reviewed-by:
Mike Rapoport <mike@compulab.co.il> Reviewed-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
Thomas Gleixner authored
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have been kept around for migration reasons. After more than two years it's time to remove them finally. This patch cleans up one of the remaining users. When all such patches hit mainline we can remove the defines and typedefs finally. Impact: cleanup Convert the last remaining users and remove the typedef. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Adrian Bunk authored
Add the missing MODULE_LICENSE("GPL"). Signed-off-by:Adrian Bunk <bunk@kernel.org> Cc: Balaji Rao <balajirrao@openmoko.org> Cc: Andy Green <andy@openmoko.com> Signed-off-by:
-
Mark Brown authored
No impact unless someone has written additional kernel code. Signed-off-by:
-
Rakib Mullick authored
Impact: Fix section mismatch. clocks_init() has been called from twl4030_probe() which is a non-init function. Since probing can be done anytime so clocks_init will be called anytime too. So we mark clock_init() as non-init. LD drivers/mfd/built-in.o WARNING: drivers/mfd/built-in.o(.text+0x8dd9): Section mismatch in reference from the function twl4030_probe() to the function .init.text:clocks_init() The function twl4030_probe() references the function __init clocks_init(). This is often because twl4030_probe lacks a __init annotation or the annotation of clocks_init is wrong. Signed-off-by:
Rakib Mullick <rakib.mullick@gmail.com> Signed-off-by:
-
Mark Brown authored
This includes the USB current limit status override which is used in the power management driver. Signed-off-by:
-
git://aeryn.fluff.org.uk/bjdooks/linuxLinus Torvalds authored
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux: i2c-stu300: Make driver depend on MACH_U300 i2c-s3c2410: use resource_size() i2c: Use resource_size macro i2c: ST DDC I2C U300 bus driver v3 i2c-bfin-twi: pull in io.h for ioremap()
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/radeon: switch to using late_initcall radeon legacy chips: tv dac bg/dac adj updates drm/radeon: introduce kernel modesetting for radeon hardware drm: Add the TTM GPU memory manager subsystem. drm: Memory fragmentation from lost alignment blocks drm/radeon: fix mobility flags on new PCI IDs.
-
David Howells authored
Authentication error abort codes should be translated to appropriate Linux error codes, rather than all being translated to EREMOTEIO - which indicates that the server had internal problems. Additionally, a server shouldn't be marked unavailable and the next server tried if an authentication error occurs. This will quickly make all the servers unavailable to the client. Instead the error should be returned straight to the user. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
David Howells authored
Connections that have seen a connection-level abort should not be reused as the far end will just abort them again; instead a new connection should be made. Connection-level aborts occur due to such things as authentication failures. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6Linus Torvalds authored
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (425 commits) V4L/DVB (11870): gspca - main: VIDIOC_ENUM_FRAMESIZES ioctl added. V4L/DVB (12004): poll method lose race condition V4L/DVB (11894): flexcop-pci: dmesg visible names broken V4L/DVB (11892): Siano: smsendian - declare function as extern V4L/DVB (11891): Siano: smscore - bind the GPIO SMS protocol V4L/DVB (11890): Siano: smscore - remove redundant code V4L/DVB (11889): Siano: smsdvb - add DVB v3 events V4L/DVB (11888): Siano: smsusb - remove redundant ifdef V4L/DVB (11887): Siano: smscards - add board (target) events V4L/DVB (11886): Siano: smscore - fix some new GPIO definitions names V4L/DVB (11885): Siano: Add new GPIO management interface V4L/DVB (11884): Siano: smssdio - revert to stand alone module V4L/DVB (11883): Siano: cards - add two additional (USB) devices V4L/DVB (11824): Siano: smsusb - change exit func debug msg V4L/DVB (11823): Siano: smsusb - fix typo in module description V4L/DVB (11822): Siano: smscore - bug fix at get_device_mode V4L/DVB (11821): Siano: smscore - fix isdb-t firmware name V4L/DVB (11820): Siano: smscore - fix byte ordering bug V4L/DVB (11819): Siano: smscore - fix get_common_buffer bug V4L/DVB (11818): Siano: smscards - assign gpio to HPG targets ...
-
Benjamin Herrenschmidt authored
Some architectures need to initialize SLAB caches to be able to allocate page tables. They do that from pgtable_cache_init() so the later should be called earlier now, best is before vmalloc_init(). Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Linus Torvalds authored
* akpm: (182 commits) fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset fbdev: *bfin*: fix __dev{init,exit} markings fbdev: *bfin*: drop unnecessary calls to memset fbdev: bfin-t350mcqb-fb: drop unused local variables fbdev: blackfin has __raw I/O accessors, so use them in fb.h fbdev: s1d13xxxfb: add accelerated bitblt functions tcx: use standard fields for framebuffer physical address and length fbdev: add support for handoff from firmware to hw framebuffers intelfb: fix a bug when changing video timing fbdev: use framebuffer_release() for freeing fb_info structures radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb? s3c-fb: CPUFREQ frequency scaling support s3c-fb: fix resource releasing on error during probing carminefb: fix possible access beyond end of carmine_modedb[] acornfb: remove fb_mmap function mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF mb862xxfb: restrict compliation of platform driver to PPC Samsung SoC Framebuffer driver: add Alpha Channel support atmel-lcdc: fix pixclock upper bound detection offb: use framebuffer_alloc() to allocate fb_info struct ... Manually fix up conflicts due to kmemcheck in mm/slab.c -
Mike Frysinger authored
Signed-off-by:
Mike Frysinger <vapier@gentoo.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by:
-
Mike Frysinger authored
The remove member of the platform_driver bfin_t350mcqb_driver should use __devexit_p() to refer to the remove function, and that function should get __devexit markings. Likewise, the probe function should be marked with __devinit and not __init. Also, module_init() functions should be marked with __init rather than __devinit. Signed-off-by:
-
Vivek Kutal authored
The dma_alloc_* functions sets the memory to 0 before returning so there is no need to call memset after the allocation. Also no point in clearing the memory when disabling the buffer. Signed-off-by:
Vivek Kutal <vivek.kutal@azingo.com> Signed-off-by:
-
Mike Frysinger authored
The local fbinfo/info vars in the suspend functions don't actually get used which cause ugly gcc warnings, so drop them. Signed-off-by:
-
Mike Frysinger authored
Signed-off-by:
-
Kristoffer Ericson authored
Add accelerated bitblt functions to s1d13xxx based video chipsets, more specificly functions copyarea and fillrect. It has only been tested and activated for 13506 chipsets but is expected to work for the majority of s1d13xxx based chips. This patch also cleans up the driver with respect of whitespaces and other formatting issues. We update the current status comments. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
Kristoffer Ericson <kristoffer.ericson@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by:
-
Krzysztof Helt authored
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len for physical address and length of framebuffer. This also fixes output of the 'fbset -i' command - address and length of the framebuffer are displayed correctly. Signed-off-by:
Krzysztof Helt <krzysztof.h1@wp.pl> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dave Airlie authored
With KMS we have ran into an issue where we really want the KMS fb driver to be the one running the console, so panics etc can be shown by switching out of X etc. However with vesafb/efifb built-in, we end up with those on fb0 and the KMS fb driver on fb1, driving the same piece of hw, so this adds an fb info flag to denote a firmware fbdev, and adds a new aperture base/size range which can be compared when the hw drivers are installed to see if there is a conflict with a firmware driver, and if there is the firmware driver is unregistered and the hw driver takes over. It uses new aperture_base/size members instead of comparing on the fix smem_start/length, as smem_start/length might for example only cover the first 1MB of the PCI aperture, and we could allocate the kms fb from 8MB into the aperture, thus they would never overlap. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
Dave Airlie <airlied@redhat.com> Acked-by:
Peter Jones <pjones@redhat.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by:
-
Paul Menzel authored
When changing video timing dynamically via fbset the screen sporadically is rendered black. With the attached fix which disables VCO prior to timing register change the problem disappears. I had a look at the Xserver register setup code. Here the VCO is disabled in the same way [1]. This patch is taken from vga-sync-field version 0.0.11 [2][3]. [1] http://cgit.freedesktop.org/xorg/driver/xf86-video-intel/tree/src/i830_= driver.c [2] http://lowbyte.de/vga-sync-fields/vga-sync-fields-0.0.11.tgz [3] http://easy-vdr.de/git?p=frc.git/.git;a=commit;h=dcc3b863e5a663652587619c357bd20075af6896 2587619c357bd20075af6896 Signed-off-by:
Thomas Hilber <sparkie@lowbyte.de> Signed-off-by:
Paul Menzel <paulepanter@users.sourceforge.net> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by:
-
Krzysztof Helt authored
Use the framebuffer_release() for freeing fb_info structures allocated with framebuffer_alloc(). Signed-off-by:
-
Roel Kluin authored
P2G2CLK_ALWAYS_ONb is tested twice, 2nd should be P2G2CLK_DAC_ALWAYS_ONb. [akpm@linux-foundation.org: remove duplicated bitwise-OR of PIXCLKS_CNTL__R300_P2G2CLK_ALWAYS_ONb too] Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Acked-by:
-
Ben Dooks authored
Add support for CPU frequency scaling in the S3C24XX video driver. Signed-off-by:
Simtec Linux Team <linux@simtec.co.uk> Signed-off-by:
Ben Dooks <ben@simtec.co.uk> Cc: Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
-
Krzysztof Helt authored
All resources are released in s3c_fb_win_release so remove other places of resources releasing. Add releasing of an allocated fb_info structure as well. Signed-off-by:
-
Roel Kluin authored
This check is off-by-one. Signed-off-by:
-
Krzysztof Helt authored
The driver's fb_mmap function is essentially the same as a generic fb_mmap function. Delete driver's function and use the generic one. A difference is that generic function marks frame buffer memory as VM_IO | VM_RESERVED. The driver's function marks it as VM_IO only. Signed-off-by:
-
Arnd Bergmann authored
With this change, the driver builds fine on Microblaze, which helps allyesconfig compile tests. I did not test sparc, but the change should have the same effect there. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Anatolij Gustschin <agust@denx.de> Tested-by:
-
Julian Calaby authored
The OpenFirmware part of this driver is uncompilable on SPARC due to it's dependance on several PPC specific functions. Restricting this to PPC to prevent these build errors: CC drivers/video/mb862xx/mb862xxfb.o drivers/video/mb862xx/mb862xxfb.c: In function 'of_platform_mb862xx_probe': drivers/video/mb862xx/mb862xxfb.c:559: error: implicit declaration of function 'of_address_to_resource' drivers/video/mb862xx/mb862xxfb.c:575: error: 'NO_IRQ' undeclared (first use in this function) drivers/video/mb862xx/mb862xxfb.c:575: error: (Each undeclared identifier is reported only once drivers/video/mb862xx/mb862xxfb.c:575: error: for each function it appears in.) This was found using randconfig builds. Signed-off-by:
Julian Calaby <julian.calaby@gmail.com> Signed-off-by:
-
InKi Dae authored
Add support for the ARGB1888 and ARGB4888 hardware to the Samsung SoC Framebuffer driver (s3c-fb.c). ARGB1888 and ARGB4888 is decided by var->transp.length and this variable is set by s3c_fb_check_var(). In s3c_fb_check_var(), if var->vits_per_pixel is 25 or 28, then var->transp.length would be 1 or 3. Therefore alpha mode(ARGB1888 or ARGB4888) could be decided through that variable. For using alpha mode, you need to set the following: This code should be added to your machine code as platform data. static struct s3c_fb_pd_win xxx_fb_win0 = { /* this is to ensure we use win0 */ .win_mode = { .pixclock = (8+8+8+240)*(38+4+38+400), .left_margin = 8, .right_margin = 8, .upper_margin = 38, .lower_margin = 38, .hsync_len = 8, .vsync_len = 4, .xres = 240, .yres = 400, }, .max_bpp = 32, .default_bpp = 24, }; static struct s3c_fb_pd_win xxx_fb_win1 = { .win_mode = { .pixclock = (8+8+8+240)*(38+4+38+400), .left_margin = 8, .right_margin = 8, .upper_margin = 38, .lower_margin = 38, .hsync_len = 8, .vsync_len = 4, .xres = 240, .yres = 400, }, .max_bpp = 32, .default_bpp = 28, }; static struct s3c_fb_platdata xxx_lcd_pdata __initdata = { .win[0] = &ncp_fb_win0, .win[1] = &ncp_fb_win1, .vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB, .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC, .setup_gpio = xxx_fb_gpio_setup, }; s3c_fb_set_platdata(&xxx_lcd_pdata); The above code sets pixelformat for window0 layer to RGB888 and window1 layer to ARGB4888. Signed-off-by:InKi Dae <inki.dae@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kyungmin Park <kmpark@infradead.org> Signed-off-by:
-
