- 07 Dec, 2006 40 commits
-
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (43 commits) [wireless] zd1211rw: workqueue-related build fixes [netdrvr] netxen: workqueue-related build fixes [PATCH] sky2: sparse warnings [PATCH] skge: fix sparse warnings [PATCH] myri10ge: write as 2 32-byte blocks in myri10ge_submit_8rx [PATCH] sky2: receive queue watermark tweak [PATCH] sky2: beter ram buffer partitioning [PATCH] sky2: add comments to PCI ids [PATCH] sky2: add PCI for 88ec033 [PATCH] AT91RM9200 Ethernet: Use dev_alloc_skb() [PATCH] AT91RM9200 Ethernet: Add netpoll / netconsole support [PATCH] AT91RM9200 Ethernet: Move check_timer variable and use mod_timer() [PATCH] AT91RM9200 Ethernet: Remove 'at91_dev' and use netdev_priv() [PATCH] ipw2200: Fix debug output endian issue [PATCH] ipw2200: Fix a typo [PATCH] ipw2200: Update version stamp to 1.2.0 [PATCH] ipw2200: Add IEEE80211_RADIOTAP_TSFT for promiscuous mode [PATCH] softmac: fix unbalanced mutex_lock/unlock in ieee80211softmac_wx_set_mlme [PATCH] softmac: Fixed handling of deassociation from AP [PATCH] ipw2200: replace kmalloc+memset with kcalloc ...
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (48 commits) [NETFILTER]: Fix non-ANSI func. decl. [TG3]: Identify Serdes devices more clearly. [TG3]: Use msleep. [TG3]: Use netif_msg_*. [TG3]: Allow partial speed advertisement. [TG3]: Add TG3_FLG2_IS_NIC flag. [TG3]: Add 5787F device ID. [TG3]: Fix Phy loopback. [WANROUTER]: Kill kmalloc debugging code. [TCP] inet_twdr_hangman: Delete unnecessary memory barrier(). [NET]: Memory barrier cleanups [IPSEC]: Fix inetpeer leak in ipv4 xfrm dst entries. audit: disable ipsec auditing when CONFIG_AUDITSYSCALL=n audit: Add auditing to ipsec [IRDA] irlan: Fix compile warning when CONFIG_PROC_FS=n [IrDA]: Incorrect TTP header reservation [IrDA]: PXA FIR code device model conversion [GENETLINK]: Fix misplaced command flags. [NETLIK]: Add a pointer to the Generic Netlink wiki page. [IPV6] RAW: Don't release unlocked sock. ...
-
git://one.firstfloor.org/home/andi/git/linux-2.6Linus Torvalds authored
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (156 commits) [PATCH] x86-64: Export smp_call_function_single [PATCH] i386: Clean up smp_tune_scheduling() [PATCH] unwinder: move .eh_frame to RODATA [PATCH] unwinder: fully support linker generated .eh_frame_hdr section [PATCH] x86-64: don't use set_irq_regs() [PATCH] x86-64: check vector in setup_ioapic_dest to verify if need setup_IO_APIC_irq [PATCH] x86-64: Make ix86 default to HIGHMEM4G instead of NOHIGHMEM [PATCH] i386: replace kmalloc+memset with kzalloc [PATCH] x86-64: remove remaining pc98 code [PATCH] x86-64: remove unused variable [PATCH] x86-64: Fix constraints in atomic_add_return() [PATCH] x86-64: fix asm constraints in i386 atomic_add_return [PATCH] x86-64: Correct documentation for bzImage protocol v2.05 [PATCH] x86-64: replace kmalloc+memset with kzalloc in MTRR code [PATCH] x86-64: Fix numaq build error [PATCH] x86-64: include/asm-x86_64/cpufeature.h isn't a userspace header [PATCH] unwinder: Add debugging output to the Dwarf2 unwinder [PATCH] x86-64: Clarify error message in GART code [PATCH] x86-64: Fix interrupt race in idle callback (3rd try) [PATCH] x86-64: Remove unwind stack pointer alignment forcing again ... Fixed conflict in include/linux/uaccess.h manually Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Andrew Morton authored
In file included from include/asm/patch.h:14, from arch/ia64/kernel/patch.c:10: include/linux/elf.h:375: warning: "struct file" declared inside parameter list include/linux/elf.h:375: warning: its scope is only this definition or declaration, which is probably not what you want Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Paul Menage authored
When using fake NUMA setup, the number of memory nodes can greatly exceed the number of CPUs. So the current limit in cpuset_common_file_write() is insufficient. Signed-off-by:
Paul Menage <menage@google.com> Acked-by:
Paul Jackson <pj@sgi.com> Signed-off-by:
-
Avantika Mathur authored
Removes all inline keywords, since the compiler will make static functions inline when it is appropriate. Signed-off-by:
Avantika Mathur <mathur@us.ibm.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by:
-
Avantika Mathur authored
Performs kmalloc to kzalloc conversion Signed-off-by:
-
Avantika Mathur authored
changes instances of if ((lhs = expression)) { to the preferred coding style lhs=expression; if (lhs) { Signed-off-by: -
Hugh Dickins authored
Port fix to the off-by-one in find_next_usable_block's memscan from ext2 to ext3; but it didn't cause a serious problem for ext3 because the additional ext3_test_allocatable check rescued it from the error. Signed-off-by:
Mingming Cao <cmm@us.ibm.com> Signed-off-by:
Hugh Dickins <hugh@veritas.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by:
-
Hugh Dickins authored
ext3_new_blocks has a nice io_error label for setting -EIO, so goto that in the one place that doesn't already use it. Signed-off-by:
-
Hugh Dickins authored
The reservations tree is an rb_tree not a list, so it's less confusing to use rb_entry() than list_entry() - though they're both just container_of(). Signed-off-by:
-
Hugh Dickins authored
rsv_end is the last block within the reservation, so alloc_new_reservation should accept start_block == rsv_end as success. Signed-off-by:
-
Hugh Dickins authored
grp_goal 0 is a genuine goal (unlike -1), so ext3_try_to_allocate_with_rsv should treat it as such. Signed-off-by:
-
Hugh Dickins authored
ext3_new_blocks should reset the reservation window size to 0 when squeezing the last blocks out of an almost full filesystem, so the retry doesn't skip any groups with less than half that free, reporting ENOSPC too soon. Signed-off-by:
-
Randy Dunlap authored
Fix build warnings for PROC_FS=n. drivers/char/ipmi/ipmi_poweroff.c:707: warning: label 'out_err' defined but not used drivers/char/ipmi/ipmi_msghandler.c:1774: warning: 'ipmb_file_read_proc' defined but not used drivers/char/ipmi/ipmi_msghandler.c:1790: warning: 'version_file_read_proc' defined but not used drivers/char/ipmi/ipmi_msghandler.c:1801: warning: 'stat_file_read_proc' defined but not used Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Cc: Corey Minyard <minyard@acm.org> Signed-off-by:
-
Corey Minyard authored
Increase the maximum message size a KCS interface supports to the maximum message size the rest of the driver supports. Some systems really support messages this big. Signed-off-by:
Corey Minyard <cminyard@mvista.com> Cc: Patrick Schoeller <Patrick.Schoeller@hp.com> Signed-off-by:
-
Corey Minyard authored
The IPMI BT subdriver has been patched to survive "long busy" timeouts seen during firmware upgrades and resets. The patch never returns the HOSED state, synthesizes response messages with meaningful completion codes, and recovers gracefully when the hardware finishes the long busy. The subdriver now issues a "Get BT Capabilities" command and properly uses those results. More informative completion codes are returned on error from transaction starts; this logic was propogated to the KCS and SMIC subdrivers. Finally, indent and other style quirks were normalized. Signed-off-by:
Rocky Craig <rocky.craig@hp.com> Signed-off-by:
Corey Minyard <minyard@acm.org> Signed-off-by:
-
Corey Minyard authored
Change pci_module_init() to the new interface, and check the return code to avoid warnings and give the user useful information if this fails. Signed-off-by:
-
Corey Minyard authored
X86 boards generally use ACPI for the power management interactions with the BMC. However, non-x86 boards need some help. This patch adds the help for the Motorola PigeonPoint-based IPMCs. Signed-off-by:
Joseph Barnett <jbarnett@motorola.com> Signed-off-by:
-
Corey Minyard authored
Add the ability to hot add and remove interfaces in the ipmi_si driver. Any users who have the device open will get errors if they try to send a message. Signed-off-by:
-
Corey Minyard authored
Make sure to delay a little in the IPMI poll routine so we can pass in a timeout time and thus time things out. Signed-off-by:
-
Corey Minyard authored
When the IPMI message handler requested that the interface look for events, the ipmi_si driver would request flags, see if the event buffer full flag was set, then request events. It's better to just send the request for events, as it cuts one message out of the transaction if there happens to be events, and it will fetch events even if the event buffer was not full. Signed-off-by:
-
Corey Minyard authored
Some commands and operations on a BMC can cause the BMC to "go away" for a while. This can cause the automatic flag processing and other things of that nature to timeout and generate annoying logs, or possibly cause other bad things to happen when in firmware update mode. Add detection of those commands (cold reset, warm reset, and any firmware command) and turns off automatic processing for 30 seconds. It also add a manual override either way. Signed-off-by:
-
Corey Minyard authored
This modifies the IPMI driver so that a lower-level interface can be dynamically removed while in use so it can support hot-removal of hardware. It also adds the ability to specify and dynamically change the IPMI interface the watchdog timer and the poweroff code use. Signed-off-by:
-
Corey Minyard authored
Pass in the sysfs name from the lower-level IPMI driver, as the coming IPMI serial driver will need that to link properly from the serial device sysfs directory. Signed-off-by:
-
Corey Minyard authored
Remove the arbitrary limit of number of IPMI interfaces. This has been tested with 8 interfaces. Signed-off-by:
-
Corey Minyard authored
Add the product id to the driver model platform device name, in addition to the device id. The IPMI spec does not require that individual BMCs in a system have unique devices IDs, but it does require that the product id/device id combination be unique. This also removes a redundant check and cleans up error handling when the sysfs registration fails. Signed-off-by:
-
Paul Clements authored
Allow nbd to expose the nbd-client daemon's PID in /sys/block/nbd<x>/pid. This is helpful for tracking connection status of a device and for determining which nbd devices are currently in use. Signed-off-by:
Paul Clements <paul.clements@steeleye.com> Signed-off-by:
-
Ingo Molnar authored
Sometimes the kernel prints something interesting while userspace bootup keeps messages turned off via loglevel. Enable the printing of /all/ kernel messages via the "ignore_loglevel" boot option. Off by default. Signed-off-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Ingo Molnar authored
The hash_lock must only ever be taken with irqs disabled. This happens in all the important places, except one codepath: register_lock_class(). The race should trigger rarely because register_lock_class() is quite rare and single-threaded (happens during init most of the time). The fix is to disable irqs. ( bug found live in -rt: there preemption is alot more agressive and preempting with the hash-lock held caused a lockup.) Signed-off-by:
-
Erik Mouw authored
The ext[23] mailing list moved from sf.net to vger.kernel.org so update the MAINTAINERS file. Signed-off-by:
Erik Mouw <erik@harddisk-recovery.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by:
-
Johann Lombardi authored
Fix a nit in ext4_ext_calc_credits_for_insert(). Besides, credits for the new root are already added in the index split accounting. Signed-off-by:
Johann Lombardi <johann.lombardi@bull.net> Signed-off-by:
Alex Tomas <alex@clusterfs.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by:
-
Benjamin LaHaise authored
Remove the ki_retried member from struct kiocb. I think the idea was bounced around a while back, but Arnaldo pointed out another reason that we should dig it up when he pointed out that the last cacheline of struct kiocb only contains 4 bytes. By removing the debugging member, we save more than the 8 byte on 64 bit machines. Signed-off-by:
Benjamin LaHaise <bcrl@kvack.org> Acked-by:
Ken Chen <kenneth.w.chen@intel.com> Acked-by:
Zach Brown <zach.brown@oracle.com> Signed-off-by:
-
Chen, Kenneth W authored
io_submit_one assigns ki_left = ki_nbytes = iocb->aio_nbytes, then calls down to aio_setup_iocb, then to aio_setup_single_vector. In there, ki_nbytes is reassigned to the same value it got two call stack above it. There is no need to do so. Signed-off-by:
-
Magnus Damm authored
The elf note saving code is currently duplicated over several architectures. This cleanup patch simply adds code to a common file and then replaces the arch-specific code with calls to the newly added code. The only drawback with this approach is that s390 doesn't fully support kexec-on-panic which for that arch leads to introduction of unused code. Signed-off-by:
Magnus Damm <magnus@valinux.co.jp> Cc: Vivek Goyal <vgoyal@in.ibm.com> Cc: Andi Kleen <ak@suse.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Alexey Dobriyan authored
On Sat, Dec 02, 2006 at 11:47:44PM +0300, Alexey Dobriyan wrote: > David Binderman compiled 2.6.19 with icc and grepped for "was set but never > used". Many warnings are on > http://coderock.org/kj/unused-2.6.19-fs Heh, the very first line: fs/exec.c(1465): remark #593: variable "flag" was set but never used fs/exec.c: 1477 /* 1478 * We cannot trust fsuid as being the "true" uid of the 1479 * process nor do we know its entire history. We only know it 1480 * was tainted so we dump it as root in mode 2. 1481 */ 1482 if (mm->dumpable == 2) { /* Setuid core dump mode */ 1483 flag = O_EXCL; /* Stop rewrite attacks */ 1484 current->fsuid = 0; /* Dump root private */ 1485 } And then filp_open follows with "flag" totally ignored. (akpm: this restores the code to Alan's original version. Andi's "Support piping into commands in /proc/sys/kernel/core_pattern" (cset d025c9db) broke it). Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@kerenl.org> Cc: Andi Kleen <ak@suse.de> Signed-off-by:
-
Adrian Bunk authored
Make the contents of the userspace asm/setup.h header consistent on all architectures: - export setup.h to userspace on all architectures - export only COMMAND_LINE_SIZE to userspace - frv: move COMMAND_LINE_SIZE from param.h - i386: remove duplicate COMMAND_LINE_SIZE from param.h - arm: - export ATAGs to userspace - change u8/u16/u32 to __u8/__u16/__u32 Signed-off-by:
Adrian Bunk <bunk@stusta.de> Acked-by:
Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Jun Chen authored
Twenty characters in cp936 are not correctly handled. They're all in the U00 plane. nls_cp936 converts all U00XY to XY but this is not correct for some characters.(e.g. U00B7 -> A1A4, U00A8 -> A1A7). This problem is fixed by generating u2c_00 based on all c2u_xx and changing uni2char() to give U00 plane a special handling. The "â¬"(U20AC,80 in cp936) is also be handled properly. Acked-by:
Gang Chen <cgdlut@gmail.com> Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
-
Helge Deller authored
- move some file_operations structs into the .rodata section - move static strings from policy_types[] array into the .rodata section - fix generic seq_operations usages, so that those structs may be defined as "const" as well [akpm@osdl.org: couple of fixes] Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Yan Burman authored
Replace kmalloc+memset with kzalloc Signed-off-by:
Yan Burman <burman.yan@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
