- 10 Oct, 2023 10 commits
-
-
Fabio Estevam authored
Pass 'fsl,imx8dl-scu-pd' to fix the following schema warning: system-controller: power-controller:compatible:0: 'fsl,scu-pd' is not one of ['fsl,imx8qm-scu-pd', 'fsl,imx8qxp-scu-pd'] from schema $id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#Signed-off-by:
Fabio Estevam <festevam@denx.de> Signed-off-by:
Shawn Guo <shawnguo@kernel.org>
-
Frank Li authored
Enable uart2 and uart3 for imx8qm-mek board. Signed-off-by:
Frank Li <Frank.Li@nxp.com> Signed-off-by:
-
Frank Li authored
Enable uart2 and uart3 for imx8qxp-mek board. Signed-off-by:
-
Frank Li authored
Original irq number combined UART irq and DMA irq. These doesn't match uart driver and dma engine's expection. Update to the irq numbers, which just uart can trigger. Signed-off-by:
-
Frank Li authored
imx8qm have difference dma channel number for uart[0..3]. Signed-off-by:
-
Frank Li authored
Add dma support uart[0..3]. Signed-off-by:
-
Frank Li authored
edma<n> is missed, add them. Signed-off-by:
-
Laurentiu Tudor authored
Wrap the usb controllers in an intermediate simple-bus and use it to constrain the dma address size of these usb controllers to the 40b that they generate toward the interconnect. This is required because the SoC uses 48b address sizes and this mismatch would lead to smmu context faults [1] because the usb generates 40b addresses while the smmu page tables are populated with 48b wide addresses. [1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002000010 xhci-hcd xhci-hcd.0.auto: irq 108, io mem 0x03100000 xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xffffffb000, fsynr=0x0, cbfrsynra=0xc01, cb=3 Signed-off-by:
Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by:
-
Yannic Moog authored
phyGATE-Tauri uses a phyCORE-i.MX8MM SoM. Add device tree for the board. Signed-off-by:
Yannic Moog <y.moog@phytec.de> Signed-off-by:
-
Shawn Guo authored
i.MX fixes for 6.6: - A couple of i.MX8MP device tree changes from Adam Ford to fix clock configuration regressions caused by 16c98452 ("arm64: dts: imx8mp: don't initialize audio clocks from CCM node"). - Fix pmic-irq-hog GPIO line in imx93-tqma9352 device tree. - Fix a mmemory leak with error handling path of imx_dsp_setup_channels() in imx-dsp driver. - Fix HDMI node in imx8mm-evk device tree. - Add missing clock enable functionality for imx8mm_soc_uid() function in soc-imx8m driver. - Add missing imx8mm-prt8mm.dtb build target.
-
- 25 Sep, 2023 30 commits
-
-
Fabio Estevam authored
The Thermal Monitoring Unit (TMU) interrupt is number 83. Describe it in the devicetree to fix the following schema warning: imx93-11x11-evk.dtb: tmu@44482000: 'oneOf' conditional failed, one must be fixed: 'interrupts' is a required property 'interrupts-extended' is a required property from schema $id: http://devicetree.org/schemas/thermal/qoriq-thermal.yaml#Signed-off-by:
-
Fabio Estevam authored
Per i2c-imx-lpi2c.yaml, the imx8dxl lpi2c compatible should be: compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c"; Change it accordingly to fix the following schema warning: imx8dxl-evk.dtb: i2c@5a800000: compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,imx8dxl-lpi2c', 'fsl,imx8qxp-lpi2c', 'fsl,imx7ulp-lpi2c'] is too long 'fsl,imx8dxl-lpi2c' is not one of ['fsl,imx7ulp-lpi2c'] 'fsl,imx7ulp-lpi2c' was expected from schema $id: http://devicetree.org/schemas/i2c/i2c-imx-lpi2c.yaml#Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Fabio Estevam authored
Per fsl,scu-pinctrl.yaml, the pinctrl node names should end with 'grp'. Change them to fix the following schema warning: imx8qxp-colibri-iris-v2.dtb: pinctrl: 'enable_3v3_vmmc', 'lcd-lvds' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/pinctrl/fsl,scu-pinctrl.yaml#Signed-off-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by:
-
Fabio Estevam authored
Use the full compatible list for the imx8dl FEC as per fsl,fec.yaml. This fixes the following schema warning: imx8dxl-evk.dtb: ethernet@5b040000: compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,imx8qm-fec'] is too short 'fsl,imx8qm-fec' is not one of ['fsl,imx25-fec', 'fsl,imx27-fec', 'fsl,imx28-fec', 'fsl,imx6q-fec', 'fsl,mvf600-fec', 'fsl,s32v234-fec'] 'fsl,imx8qm-fec' is not one of ['fsl,imx53-fec', 'fsl,imx6sl-fec'] 'fsl,imx8qm-fec' is not one of ['fsl,imx35-fec', 'fsl,imx51-fec'] 'fsl,imx8qm-fec' is not one of ['fsl,imx6ul-fec', 'fsl,imx6sx-fec'] 'fsl,imx8qm-fec' is not one of ['fsl,imx7d-fec'] 'fsl,imx8mq-fec' was expected 'fsl,imx8qm-fec' is not one of ['fsl,imx8mm-fec', 'fsl,imx8mn-fec', 'fsl,imx8mp-fec', 'fsl,imx93-fec'] 'fsl,imx8qm-fec' is not one of ['fsl,imx8dxl-fec', 'fsl,imx8qxp-fec'] 'fsl,imx8qm-fec' is not one of ['fsl,imx8ulp-fec'] from schema $id: http://devicetree.org/schemas/net/fsl,fec.yaml#Signed-off-by:
-
Fabio Estevam authored
The 'nand-on-flash-bbt' property is a property for the NAND device, not for the GPMI nand controller. Remove it to fix the following schema warnings: imx8mm-ddr4-evk.dtb: nand-controller@33002000: Unevaluated properties are not allowed ('nand-on-flash-bbt' was unexpected) from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml# imx8mn-bsh-smm-s2.dtb: nand-controller@33002000: Unevaluated properties are not allowed ('nand-on-flash-bbt' was unexpected) from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#Signed-off-by: -
Fabio Estevam authored
The mac-address is passed as a subnode of the eeprom and its 'reg' property describe a range of addresses in the eeprom. Therefore, #size-cells should be set to 1 instead of 0. This fixes the following schema warnings: imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: #size-cells:0:0: 1 was expected from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml# imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: mac-address@0:reg: [[0], [12]] is too long from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml# imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: mac-address@c:reg: [[12], [12]] is too long from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml# imx8mp-debix-som-a-bmb-08.dtb: eeprom@52: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'mac-address@0', 'mac-address@c' were unexpected) from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
-
Fabio Estevam authored
The PWM interrupt is mandatory per imx-pwm.yaml. Add them. This also fixes the followig schema warning: imx8qm-apalis-v1.1-ixora-v1.2.dtb: pwm@5d000000: 'oneOf' conditional failed, one must be fixed: 'interrupts' is a required property 'interrupts-extended' is a required property from schema $id: http://devicetree.org/schemas/pwm/imx-pwm.yaml#Signed-off-by:
-
Rob Herring authored
imx8mm-prt8mm.dts was not getting built. Add it to the build. Fixes: 58497d7a ("arm64: dts: imx: add Protonic PRT8MM board") Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Fabio Estevam authored
Per bq25890.yaml, 'phys', 'ti,use-vinmin-threshold', 'ti,vinmin-threshold' are not valid properties. Remove them to fix the following schema warning: imx8mq-librem5-r2.dtb: charger@6a: Unevaluated properties are not allowed ('phys', 'ti,use-vinmin-threshold', 'ti,vinmin-threshold' were unexpected) from schema $id: http://devicetree.org/schemas/power/supply/bq25890.yaml#Signed-off-by: -
Fabio Estevam authored
Per fsl-imx-gpio.yaml, 'pad-wakeup' and 'pad-wakeup-num' are not valid properties/ Remove them to fix the following schema warning: imx8qm-apalis-ixora-v1.1.dtb: gpio@5d0a0000: 'pad-wakeup', 'pad-wakeup-num' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml#Signed-off-by:
-
Fabio Estevam authored
Per fsl-imx-gpio.yaml, 'ngpios' is not a valid property. Remove it to fix the following schema warning: imx8qm-apalis-v1.1-ixora-v1.2.dtb: gpio@5d0d0000: 'ngpios' does not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/gpio/fsl-imx-gpio.yaml#Signed-off-by:
-
Fabio Estevam authored
Per mdio-gpio.yaml, the node name should be 'mdio'. Change it accordingly to fix the following schema warning: imx8mq-zii-ultra-zest.dtb: bitbang-mdio: $nodename:0: 'bitbang-mdio' does not match '^mdio(@.*)?' from schema $id: http://devicetree.org/schemas/net/mdio-gpio.yaml#Signed-off-by:
-
Fabio Estevam authored
Per i2c-mux-pca954x.yaml, the PCA9546 I2C subnodes should be in the 'i2c@' format. Change it accordingly to fix the following schema warning: imx8mm-nitrogen-r2.dtb: i2c-mux@70: Unevaluated properties are not allowed ('i2c3@0' was unexpected) Signed-off-by: -
Fabio Estevam authored
According to st,st-sensors.yaml, the 'interrupt-names' property is not a valid one. Remove it to fix the following schema warnings: imx8mp-venice-gw73xx-2x.dtb: accelerometer@19: 'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/iio/st,st-sensors.yaml#Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
-
Fabio Estevam authored
spi-nxp-fspi.yaml expects the clock-names entries to be in the following order: "fspi_en", "fspi". Change it accordingly to fix the following schema warnings: imx8ulp-evk.dtb: spi@29810000: clock-names:0: 'fspi_en' was expected from schema $id: http://devicetree.org/schemas/spi/spi-nxp-fspi.yaml# imx8ulp-evk.dtb: spi@29810000: clock-names:1: 'fspi' was expected from schema $id: http://devicetree.org/schemas/spi/spi-nxp-fspi.yaml#Signed-off-by:
-
Fabio Estevam authored
nxp,fspi-dll-slvdly is not documented nor used anywhere. Drop this invalid property. Signed-off-by:
-
Fabio Estevam authored
The conn_enet0_root_clk node does not have any register associated with it, so it should be moved outside of soc to fix schema warning from simple-bus.yaml. Signed-off-by:
-
Fabio Estevam authored
The audio_ipg_clk node does not have any register associated with it, so it should be moved outside of soc to fix schema warning from simple-bus.yaml. Signed-off-by:
-
Fabio Estevam authored
The img_ipg_clk node does not have any register associated with it, so it should be moved outside of soc to fix schema warning from simple-bus.yaml. Signed-off-by:
-
Fabio Estevam authored
The conn clock nodes do not have any register associated with it, so they should be moved outside of soc to fix schema warning from simple-bus.yaml. Signed-off-by:
-
Fabio Estevam authored
The dma_ipg_clk node does not have any register associated with it, so it should be moved outside of soc to fix schema warning from simple-bus.yaml. Signed-off-by:
-
Fabio Estevam authored
The lsio_bus_clk node does not have any register associated with it, so it should be moved outside of soc to fix schema warning from simple-bus.yaml. Signed-off-by:
-
Fabio Estevam authored
The lsio_mem_clk is not used anywhere, so simply remove it. Signed-off-by:
-
Fabio Estevam authored
The 'funnel' node does not contain a register range, so it should be placed outside of the soc node to fix schema warnings from simple-bus.yaml. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by:
-
Fabio Estevam authored
The 'funnel' node does not contain a register range, so it should be placed outside of the soc node to fix schema warnings from simple-bus.yaml. Signed-off-by:
-
Teresa Remmet authored
Add UART2 for RS232/RS485 support. Signed-off-by:
Teresa Remmet <t.remmet@phytec.de> (Updated the node by not setting the reserved bits(BIT 0 and BIT 3) and enabled internal pullup for RX and TX.) Signed-off-by:
Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by:
Cem Tenruh <c.tenruh@phytec.de> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Signed-off-by:
-
Cem Tenruh authored
Add gpio-line-names to the imx8mp-phyboard-pollux devicetree. Signed-off-by:
-
Cem Tenruh authored
Add gpio-line-names to the imx8mp-phycore-som devicetree. Signed-off-by:
-
Teresa Remmet authored
Enable USB support for both interfaces in host mode. USB1 is directly conncted to a type-A connector and USB2 is attached to a 4-Port USB Hub. Signed-off-by:
-
Teresa Remmet authored
Add flexcan1 and flexcan2 support for CAN FD on phyBOARD-Pollux. Signed-off-by:
-
