ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly.  This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached

2. The current rt->dst._metrics init code is incorrect:
   - 'rt->dst._metrics = ort->dst._metris' is not always safe
   - Not sure what dst_copy_metrics() is trying to do here
     considering ip6_rt_blackhole_cow_metrics() always returns
     NULL

   Fix:
   - Always do dst_copy_metrics()
   - Replace ip6_rt_blackhole_cow_metrics() with
     dst_cow_metrics_generic()

3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
   This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
   It is because RTF_PCPU is set while rt->dst.from is NULL.

Fixes: d52d3997 ("ipv6: Create percpu rt6_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Phil Sutter <phil@nwl.cc>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).

It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under certain conditions EMAD responses can be returned from the device
even before setting trans_active. This will cause the EMAD Rx listener
to drop the EMAD response - as there are no active transactions - and
timeouts will be generated.

Fix this by setting trans_active before transmitting the EMAD skb.

Fixes: 4ec14b76 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit e3eea1eb ("tipc: clean up handling of message priorities")
we introduced a field in the packet header for keeping track of the
priority of fragments, since this value is not present in the specified
protocol header. Since the value so far only is used at the transmitting
end of the link, we have not yet officially defined it as part of the
protocol.

Unfortunately, the field we use for keeping this value, bits 13-15 in
in word 5, has turned out to be a poor choice; it is already used by the
broadcast protocol for carrying the 'network id' field of the sending
node. Since packet fragments also need to be transported across the
broadcast protocol, the risk of conflict is obvious, and we see this
happen when we use network identities larger than 2^13-1. This has
escaped our testing because we have so far only been using small network
id values.

We now move this field to bits 0-2 in word 9, a field that is guaranteed
to be unused by all involved protocols.

Fixes: e3eea1eb ("tipc: clean up handling of message priorities")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems that kernel memory can leak into userspace by a
kmalloc, ethtool_get_strings, then copy_to_user sequence.

Avoid this by using kcalloc to zero fill the copied buffer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2015-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Like last time, we have two small fixes:
 * fast-xmit was not doing powersave filter clearing correctly,
   disable fast-xmit while any such operations are still pending
 * a debugfs file was broken due to some infrastructure changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 6e498158 ("tipc: move link synch and failover to link aggregation level")
we introduced a new mechanism for performing link failover and
synchronization. We have now detected a bug in this mechanism.

During link synchronization we use the arrival of any packet on
the tunnel link to trig a check for whether it has reached the
synchronization point or not. This has turned out to be too
permissive, since it may cause an arriving non-last SYNCH packet to
end the synch state, just to see the next SYNCH packet initiate a
new synch state with a new, higher synch point. This is not fatal,
but should be avoided, because it may significantly extend the
synchronization period, while at the same time we are not allowed
to send NACKs if packets are lost. In the worst case, a low-traffic
user may see its traffic stall until a LINK_PROTOCOL state message
trigs the link to leave synchronization state.

At the same time, LINK_PROTOCOL packets which happen to have a (non-
valid) sequence number lower than the tunnel link's rcv_nxt value will
be consistently dropped, and will never be able to resolve the situation
described above.

We fix this by exempting LINK_PROTOCOL packets from the sequence number
check, as they should be. We also reduce (but don't completely
eliminate) the risk of entering multiple synchronization states by only
allowing the (logically) first SYNCH packet to initiate a synchronization
state. This works independently of actual packet arrival order.

Fixes: commit 6e498158 ("tipc: move link synch and failover to link aggregation level")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As originally written rt6_uncached_list_flush_dev makes no sense when
called with dev == NULL as it attempts to flush all uncached routes
regardless of network namespace when dev == NULL.  Which is simply
incorrect behavior.

Furthermore at the point rt6_ifdown is called with dev == NULL no more
network devices exist in the network namespace so even if the code in
rt6_uncached_list_flush_dev were to attempt something sensible it
would be meaningless.

Therefore remove support in rt6_uncached_list_flush_dev for handling
network devices where dev == NULL, and only call rt6_uncached_list_flush_dev
 when rt6_ifdown is called with a network device.

Fixes: 8d0b94af ("ipv6: Keep track of DST_NOCACHE routes in case of iface down/unregister")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLANs 0 and 4095 are reserved and shouldn't be used, add checks to
switchdev similar to the bridge. Also make sure ids above 4095 cannot
be passed either.

Fixes: 47f8328b ("switchdev: add new switchdev bridge setlink")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

Patch 1 fixes a FW image compatibility check in the driver that
prevents certain FW images from being flashed on BE3 (not BE3-R)
adapters.

Patch 2 fixes a spin_lock not being released in a failure case in
be_cmd_notify_wait().

Patch 3 includes a workaround to pad packets that are only 32b long or less
to be applicabe to BE3 too. This workaround was currently applied only to
Skyhawk and Lancer chips. Such packets are causing BE3's TX path to stall
on a SR-IOV config.

Patch 4 fixes the be_cmd_get_profile_config() routine to set the pf_num
field in the cmd request. The FW requires this field to be set for it to
return the specific function's descriptors. If not set, the FW returns
the descriptors of all the functions on the device. If the first descriptor
is not what is being queried for, the driver will read wrong data.
This patch fixes this issue by using the GET_CNTL_ATTRIB cmd to query the
real pci_func_num of a function and then uses it in the GET_PROFILE_CONFIG
cmd.

Patch 5 completes an earlier fix that removed the vlan promisc capability
for VFs. The earlier fix did not update the removal of this capability from
the profile descriptor of the VF. This causes the VF driver to request this
capability when it tries to create it's interface at probe time. This could
potentailly cause the VF probe to fail if the FW enforces strict checking of
the flags based on what was provisoned by the PF.  This strict checking is
not being done by FW currently but will be fixed in a future version. This
patch fixes this issue by updating the VF's profile descriptor so that they
match the interface capability flags provisioned by the PF.

Pls consider adding these patches to the net tree. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 435452aa ("Prevent VFs from enabling VLAN promiscuous mode")
fixed the PF driver to not include the VLAN promisc capability while
provisioning the interface for a VF. But the fix did not remove this
capability from the profile descriptor of the VF. This causes the VF
driver to request this capability when it tries to create it's interface
at probe time.  This could potentailly cause the VF probe to fail if the
FW enforces strict checking of the flags based on what was provisoned
by the PF.  This strict checking is not being done by FW currently but
will be fixed in a future version. This patch fixes this issue by updating
the VF's profile descriptor so that they match the interface capability
flags provisioned by the PF.

Fixes: 435452aa ("Prevent VFs from enabling VLAN promiscuous mode")
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The FW requires the pf_num field in the cmd hdr to be set for it to return
the specific function's descriptors in the GET_PROFILE_CONFIG cmd. If not
set, the FW returns the descriptors of all the functions on the device.
If the first descriptor is not what is being queried for, the driver will
read wrong data. This patch fixes this issue by using the GET_CNTL_ATTRIB
cmd to query the real pci_func_num of a function and then uses it in the
GET_PROFILE_CONFIG cmd.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On BE3 chips in SRIOV configs, the TX path stalls when a packet less
than 32B is received from the host. A workaround to pad such packets
already exists for the Skyhawk and Lancer chips. Use the same workaround
for BE3 chips too.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mcc/mbox lock is not being released when be_cmd_copy() returns
an error.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the BE3 FW image, unlike Skyhawk's, the "asic_type_rev" field doesn't
track the asic_rev of chip it is compatible with. When asic_type_rev
is 0 the image is compatible only with pre-BE3-R chips (asic_rev < 0x10).
Fix the current compatibility check to take care of this.
We hit this issue when we try to flash old BE3 images (used prior to the
release of BE3-R) on pre-BE3-R adapters.

Fixes: a6e6ff6e ("be2net: simplify UFI compatibility checking")
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit afae5ad7
  "net/fsl_pq_mdio: streamline probing of MDIO nodes"

added support for different types of MDIO devices:
1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)

However, the implementation for types 1 and 4 would mistakenly assume
a mapping of the full MDIO register set, thereby computing the address
for the TBI register starting from the containing structure.
The TBI register would therefore be accessed at a wrong (much bigger)
address, not giving the expected result at all.
This patch restores the correct behavior we had prior to the above one.

The consequences of this bug are apparent when trying to access a PHY
with the same address as the value contained in the initial value of
the TBI register (normally 0); in that case you'll get answers from the
internal TBI device (even though MDIO/MDC pins are actually *also*
toggling on the physical bus!).
Beware that you also need to add a fake tbi node to your device tree
with an unused address.

Notice how this fix is related to commit
22066949
  "powerpc: Add TBI PHY node to first MDIO bus"

which fixed the behavior in kernel 3.3, which was later broken by the
above commit on kernel 3.7.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configuring the MDIO subsystem it is also necessary to configure
the TBI register. Make sure the TBI is contained within the mapped
register range in order to:
a) make sure the address is computed correctly
b) make users aware that we're actually accessing that register

In case of error, print a message but continue anyway.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 30686bf7 ("mac80211: convert HW flags to unsigned long
bitmap") accidentally removed the newline delimiter from the hwflags
debugfs file. Fix this by adding back the newline between the HW flags.

Cc: stable@vger.kernel.org [4.2]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[fix commit log]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

RTA_ALIGNTO is currently define as 4. It has to be 4U to prevent warning
for RTA_ALIGN and RTA_DATA expansions when -Wconversion gcc option is
enabled.
This follows NLMSG_ALIGNTO definition in <include/uapi/linux/netlink.h>.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a clone of commit 2ab95749 ("ip_forward: Drop frames with
attached skb->sk") for ipv6.

This commit has exactly the same reasons as the above mentioned commit,
namely to prevent panics during netfilter reload or a misconfigured stack.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRE point-to-point interfaces should also support ipv6 multicast. Setting
up default multicast routes on interface creation was forgotten. Add it.

Bugzilla: <https://bugzilla.kernel.org/show_bug.cgi?id=103231>
Cc: Julien Muchembled <jm@jmuchemb.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dumazet <ndumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: couple of fixes

Just a couple of small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When calculating the shift needed in order to access a bit array element
in a byte, we should multiply the index by the element size and not
assume it is fixed at 2-bits.

Fixes: 93c1edb2 ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 31557f0f ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit c0afd9ce ("fq_codel: fix return value of fq_codel_drop()")
->drop() is supposed to return the number of bytes it dropped,
but hhf_drop () returns the id of the bucket where it drops
a packet from.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Terry Lam <vtlam@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Mellanox driver update to 4.3-rc4

Small set of fixes for net, which includes Carol's patches, a fix
from Achiad to have the right behaviour for mlx5 Eth devices w.r.t
VLANs in promiscuous mode, a good-bye patch from Ido who left Mellanox
and the 1st patch from Jiri to our NIC drivers (I love one-liners)...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove Ido Shamay as co-maintainer for the mlx4 Ethernet driver,
as he no longer works for Mellanox.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device was set to promiscuous mode, we didn't disable
VLAN filtering, which is wrong behaviour, fix that.

Now when the device is set to promiscuous mode RX packets
sent over any VLAN (or no VLAN tag at all) will be accepted.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We used the wrong register name for querying the PVLC register

Fixes: a124d13e ('net/mlx5_core: Add more query port helpers')
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test interrupts fails if not all completion vectors called
request_irq. This case happens if only mlx4_en is loaded and
we have more completion vectors than rx rings.

Fixes: c66fa19c ('net/mlx4: Add EQ pool')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we get MAX_MSIX interrupts would like to have each receive ring
with his own msix interrupt line. Do not need the shared_ports
variable at mlx4_enable_msix

Fixes: 9293267a ('net/mlx4_core: Capping number of requested MSIXs to MAX_MSIX')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"Y" was the right answer for MDIO_OCTEON when this option was only
available on CAVIUM_OCTEON_SOC. But now that the option is visible on
all (64-bit) systems, this piece of advice no longer makes sense. This
helper module is selected automatically by drivers which need it
anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a6d67864 ("net: mdio-octeon: Modify driver to work on both ThunderX and Octeon")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recently added mlxsw driver produces warnings in ARM
allmodconfig:

drivers/net/ethernet/mellanox/mlxsw/pci.c: In function 'mlxsw_pci_cmd_exec':
drivers/net/ethernet/mellanox/mlxsw/pci.c:1585:59: warning: right shift count >= width of type [-Wshift-count-overflow]
linux/byteorder/big_endian.h:38:51: note: in definition of macro '__cpu_to_be32'
drivers/net/ethernet/mellanox/mlxsw/pci.c:76:2: note: in expansion of macro 'iowrite32be'

This uses upper_32_bits() to extract the bits while avoiding that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Fixes: eda6500a "mlxsw: Add PCI bus implementation"
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit c29390c6 ("xps: must clear sender_cpu before forwarding")
the skb->sender_cpu needs to be cleared before xmit.

Fixes: 3896d655 ("bpf: introduce bpf_clone_redirect() helper")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit c29390c6 ("xps: must clear sender_cpu before forwarding")
the skb->sender_cpu needs to be cleared when moving from Rx
Tx, otherwise kernel could crash.

Fixes: 2bd82484 ("xps: fix xps for stacked devices")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make unix_sk() just like inet[6]_sk() by constify'ing the sock
parameter.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joe Stringer says:

====================
OVS conntrack fixes for net

The userspace side of the Open vSwitch conntrack changes is currently
undergoing review, which has highlighted some minor bugs in the existing
conntrack implementation in the kernel, as well as pointing out some
future-proofing that can be done on the interface to reduce the need for
additional compatibility code in future.

The biggest changes here are to the userspace API for the ct_state match
field and the CT action. This series proposes to firstly extend the ct_state
match field to 32 bits, ensuring to reject any currently unsupported bits.
Secondly, rather than representing CT action flags within a 32-bit field,
simply use a netlink attribute as presence of the single flag that is
defined today. This also serves to reject unsupported ct action flag bits.

v4: Use 12-character abbreviated hashes in commit messages.
v3: Fully acked.
v2: Address minor style feedback, add acks.
v1: Initial post.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, the CT_ATTR_FLAGS attribute, when nested under the
OVS_ACTION_ATTR_CT, encoded a 32-bit bitmask of flags that modify the
semantics of the ct action. It's more extensible to just represent each
flag as a nested attribute, and this requires no additional error
checking to reject flags that aren't currently supported.
Suggested-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ct_state field was initially added as an 8-bit field, however six of
the bits are already being used and use cases are already starting to
appear that may push the limits of this field. This patch extends the
field to 32 bits while retaining the internal representation of 8 bits.
This should cover forward compatibility of the ABI for the foreseeable
future.

This patch also reorders the OVS_CS_F_* bits to be sequential.
Suggested-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>