- 22 Oct, 2010 40 commits
-
-
Michal Nazarewicz authored
This commit changes storage_common.h, file_storage.c and f_mass_storage.c to use definitions of SCSI commands from scsi/scsi.h file instead of redefining the commands in storage_common.c. scsi/scsi.h header file was missing READ_FORMAT_CAPACITIES and READ_HEADER so this commit also add those to the header. Signed-off-by:
Michal Nazarewicz <mina86@mina86.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: James Bottomley <James.Bottomley@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
matt mooney authored
For all modules, change <module>-objs to <module>-y; remove if-statements and replace with lists using the kbuild idiom; move flags to the top of the file; and fix alignment while trying to maintain the original scheme in each file. None of the dependencies are modified. Signed-off-by:
matt mooney <mfm@muteddisk.com> Acked-by:
Sam Ravnborg <sam@ravnborg.org> Acked-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Rahul Ruikar authored
In function dummy_udc_probe() call put_device() when device_register() fails. also usb_get_hcd() put before device_register() after review comment from Alan Stern. Signed-off-by:
Rahul Ruikar <rahul.ruikar@gmail.com> Signed-off-by:
-
Rahul Ruikar authored
In function usb_create_ep_devs() call put_device() when device_register() fails. Signed-off-by:
-
Anders Larsen authored
The WAGO 750-923 USB Service Cable is used for configuration and firmware updates of several industrial automation products from WAGO Kontakttechnik GmbH. Bus 004 Device 002: ID 1be3:07a6 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1be3 idProduct 0x07a6 bcdDevice 1.00 iManufacturer 1 Silicon Labs iProduct 2 WAGO USB Service Cable iSerial 3 1277796751 . . . Signed-off-by:
Anders Larsen <al@alarsen.net> Cc: stable <stable@kernel.org> Signed-off-by:
-
Peter Chen authored
At otg device mode, the otg host resume should do no-op during system resume, otherwise, the otg device will be treated as a host for enumeration. So, the otg host driver returns -ESHUTDOWN if it detects the current usb mode is device mode. The host driver has to return -ESHUTDOWN, otherwise, the usb_hc_died will be called. Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
Hans de Goede authored
Some Rockbox based mp4 players will crash when ever they see a read_capacity_16 scsi command. So add a new US_FL which tells the scsi sd driver to not issue any read_capacity_16 scsi commands. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Hans de Goede authored
I seem to have a knack for digging up buggy usb devices which don't work with Linux, and I'm crazy enough to try to make them work. So this time a friend of mine asked me to get an mp4 player (an mp3 player which can play videos on a small screen) to work with Linux. It is based on the well known rockbox chipset for which we already have an unusual devs entries to work around some of its bugs. But this model comes with an additional twist. This model chokes on read_capacity_16 calls. Now normally we don't make those calls, but this model comes with an sdcard slot and when there is no card in there (and shipped from the factory there is none), it reports a size of 0. However this time the programmers actually got the read_capacity_10 response right! So they substract one from the size as stored internally in the mp3 player before reporting it back, resulting in an answer of ... 0xffffffff sectors, causing sd.c to try a read_capacity_16, on which the device crashes. This patch adds a flag to scsi_device to indicate that a a device cannot handle read_capacity_16, and when this flag is set if a device reports an lba of 0xffffffff as answer to a read_capacity_10, assumes it tries to report a size of 0. Signed-off-by:
-
Hans de Goede authored
Appotech ax3003 (the larger brother of the ax203) based devices are even more buggy then the ax203. They will go of into lala land when ever they see a READ_DISC_INFO scsi command. So add a new US_FL which tells the scsi sr driver to not issue any READ_DISC_INFO scsi commands. [akpm@linux-foundation.org: fix build] Signed-off-by:
-
Hans de Goede authored
Some USB devices emulate a usb-mass-storage attached (scsi) cdrom device, usually this fake cdrom contains the windows software for the device. While working on supporting Appotech ax3003 based photoframes, which do this I discovered that they will go of into lala land when ever they see a READ_DISC_INFO scsi command. Thus this patch adds a scsi_device flag (which can then be set by the usb-storage driver through an unsual-devs entry), to indicate this, and makes the sr driver honor this flag. I know this sucks, but as discussed on linux-scsi list there is no other way to make this device work properly. Looking at usb traces made under windows, windows never sends a READ_DISC_INFO during normal interactions with a usb cdrom device. So as this cdrom emulation thingie becomes more common we might see more of this problem. Signed-off-by:
-
Dan Carpenter authored
This is based on an initial patch by Rahul Ruikar. The goku_remove() function can be called before device_register() so it can call device_unregister() improperly. Also if the call to device_register() fails we need to call put_device(). As I was changing the error handling in goku_probe(), I noticed that the label was "done" but actually if the function succeeds we return earlier. I renamed the error path to "err" instead of "done." Reported-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
-
Martin Fuzzey authored
The hardware can only do DMA to 4 byte aligned addresses. When this requirement is not met use PIO or a bounce buffer. PIO is used when the buffer is small enough to directly use the hardware data memory (2*maxpacket). A bounce buffer is used for larger transfers. Signed-off-by:
Martin Fuzzey <mfuzzey@gmail.com> Signed-off-by:
-
Martin Fuzzey authored
Split unmap_urb_for_dma() to allow just the setup buffer to be unmapped. This allows HCDs to use PIO for the setup buffer if it is not suitable for DMA. Signed-off-by:
-
Martin Fuzzey authored
Release the hardware resources and reset the internal HCD state associated with an isochronous endpoint when the last URB queued for it completes. Previously this was only done in then endpoint_disable() method causing usbtest 15 and 16 to hang when run twice in succession without a disconnect. Signed-off-by:
-
Martin Fuzzey authored
We already have fields describing the hardware data memory (dmem_size and dmem_offset) in the HCD private data, use them rather than the rather obscure read from the hardware descriptor. Signed-off-by:
-
Martin Fuzzey authored
Remove a local variable left over from some debugging code. Signed-off-by:
-
Martin Fuzzey authored
Check the data length of isochronous transfers is as expected. With this test #16 will now fail if the device side sends no data. Signed-off-by:
-
Martin Fuzzey authored
Signed-off-by:
-
Alan Stern authored
This patch (as1430) fixes a bug in usbcore. When a device configuration change occurs or a device is removed, the endpoints for the old config should be completely disabled. However it turns out they aren't; this is because usb_unbind_interface() calls usb_enable_interface() or usb_set_interface() to put interfaces back in altsetting 0, which re-enables the interfaces' endpoints. As a result, when a device goes through a config change or is unconfigured, the ep_in[] and ep_out[] arrays may be left holding old pointers to usb_host_endpoint structures. If the device is deauthorized these structures get freed, and the stale pointers cause errors when the the device is eventually unplugged. The solution is to disable the endpoints after unbinding the interfaces instead of before. This isn't as large a change as it sounds, since usb_unbind_interface() disables all the interface's endpoints anyway before calling the driver's disconnect routine, unless the driver claims to support "soft" unbind. This fixes Bugzilla #19192. Thanks to "Tom" Lei Ming for diagnosing the underlying cause of the problem. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
Carsten Sommer <carsten_sommer@ymail.com> CC: stable <stable@kernel.org> Signed-off-by:
-
Philippe Skowronski authored
It is safer to cancel pending requests before free dTD and dQH when controller enters suspend state. Signed-off-by:
Philippe Skowronski <philippe.skowronski@intel.com> Signed-off-by:
Hao Wu <hao.wu@intel.com> [Switch to spin_lock_irq as suggested by Alan Stern] Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Christophe Lebouc authored
This patch fixing the problem with large file transfers failing. Swap the read order to avoid unexpected RX status. Signed-off-by:
Christophe Lebouc <christophex.lebouc@intel.com> Signed-off-by:
-
Ming Lei authored
This patch adds native scatter-gather support to uhci-hcd. Reviewed-by:
Ming Lei <tom.leiming@gmail.com> Acked-by:
-
Sergei Shtylyov authored
Blackfin's musb_platform_init() needs to call gpio_free() for error cleanup iff otg_get_transceiver() call returns NULL. Signed-off-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by:
Mike Frysinger <vapier@gentoo.org> Signed-off-by:
-
Sergei Shtylyov authored
Blackfin's musb_platform_exit() forgets to call usb_nop_xceiv_unregister(). While fixing this, also remove the unneeded blank line there. Signed-off-by:
-
Sergei Shtylyov authored
Since commit 461972d8 (musb_core: don't call musb_platform_exit() twice), unloading the driver module results in a WARNING "kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode. There exists dubious and unbalanced put_device() call in musb_free() which takes place only in the OTG mode. As this commit caused musb_platform_exit() to be called (and so unregister the NOP transceiver) before this put_device() call, this function references already freed memory. On the other hand, all the glue layers miss the otg_put_transceiver() call, complementary to the otg_get_transceiver() call that they do. So, I think the solution is to get rid of the strange put_device() call, and instead call otg_put_transceiver() in the glue layers... Signed-off-by:
-
Anatolij Gustschin authored
Extends FSL EHCI platform driver glue layer to support MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI registers are in big endian format. The appropriate flags are set using the information in the platform data structure. MPC83xx system interface registers are not available on MPC512x, so the access to these registers is isolated in MPC512x case. Furthermore the USB controller clocks must be enabled before 512x register accesses which is done by providing platform specific init callback. The MPC512x internal USB PHY doesn't provide supply voltage. For boards using different power switches allow specifying DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault" properties in the device tree USB nodes. Adds documentation for this new device tree bindings. Signed-off-by:
Anatolij Gustschin <agust@denx.de> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by:
-
Anatolij Gustschin authored
Replace FSL USB platform code by simple platform driver for creation of FSL USB platform devices. The driver creates platform devices based on the information from USB nodes in the flat device tree. This is the replacement for old arch fsl_soc usb code removed by this patch. The driver uses usual of-style binding, available EHCI-HCD and UDC drivers can be bound to the created devices. The new of-style driver additionaly instantiates USB OTG platform device, as the appropriate USB OTG driver will be added soon. Signed-off-by:
-
Rainer Keller authored
The OpenDCC project is developing a new hardware. This patch adds its PID to the list of known FTDI devices. The PID can be found at http://www.opendcc.de/elektronik/usb/opendcc_usb.htmlSigned-off-by:
Rainer Keller <mail@rainerkeller.de> Cc: stable <stable@kernel.org> Signed-off-by:
-
Grazvydas Ignotas authored
Add empty functions for get/put transceiver functions too, so that drivers that optionally use them can call them without worrying that they might not exist, eliminating ifdefs. Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Acked-by:
-
Otavio Salvador authored
Signed-off-by:
Otavio Salvador <otavio@ossystems.com.br> Signed-off-by:
-
matt mooney authored
Replace EXTRA_CFLAGS with ccflags-y. Signed-off-by:
WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by:
-
Felipe Balbi authored
commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85 broke g_file_storage functionality by enabling AUTOCLEAR on all cases without caring for all gadget drivers. This patch will only enable AUTOCLEAR if our endpoint's FIFO was configured with double buffering support. Note this is not a complete fix, double buffered case still doesn't work always, but that hasn't been working for quite some time. Other than reverting the entire commit and breaking testusb with double buffered case again, I decided it was better to fix the single buffered case and spend more time fixing double buffered case properly. Signed-off-by:
-
Ming Lei authored
This patch fixes the problem reported by Sergei: >how come? we need to send ZLP before giving back the request. >Well, look at the code ionce again. We need to send ZLP *after* >request->actual == request->length, but as the check is inserted >after the ZLP send, ZLP *may* be sent once the first DMA completes, >not the last. The patch also has been discussed on the link below: http://marc.info/?t=128454814900001&r=1&w=2Signed-off-by:
Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by:
-
Heikki Krogerus authored
This will ignore any SESSREQ interrupt if musb is B state. Charger detection may cause spurious SESSREQ interrupts. Signed-off-by:
Heikki Krogerus <ext-heikki.krogerus@nokia.com> Signed-off-by:
-
Sergei Shtylyov authored
musb_g_rx() always returns if next_request() call yields NULL, so the DBG() near the function's end can never be invoked. Remove it along with unneeded 'return'; also remove the duplicate 'request' check... Signed-off-by:
-
Jon Povey authored
Wrap flags with uninitialized_var() to suppress this: drivers/usb/musb/cppi_dma.c:1158: warning: 'flags' may be used uninitialized in this function Signed-off-by:
Jon Povey <jon.povey@racelogic.co.uk> Signed-off-by:
-
T. S., Anil Kumar authored
Add support for MUSB Host DMA transfers greater than max channel length, so that such transfers won't be truncated. Signed-off-by:
Anil Shetty <anil@ti.com> Signed-off-by:
-
Bob Liu authored
Since not all platforms are using the same offset 0x10 in musb_save/restore_context() eg Blackfin the offset is 0x40, Change the indexed address to direct. Signed-off-by:
Bob Liu <lliubbo@gmail.com> Signed-off-by:
-
Maulik Mankad authored
The USB stack maps the buffer for DMA if the controller supports DMA. MUSB controller can perform DMA as well as PIO transfers. The buffer needs to be unmapped before CPU can perform PIO data transfers. Export unmap_urb_for_dma() so that drivers can perform the DMA unmapping in a sane way. Signed-off-by:
Maulik Mankad <x0082077@ti.com> Acked-by:
-
Anil Shetty authored
MUSB's DMA controller max channel length was set to 64k. Transfer length greater than this max value is being truncated. Signed-off-by:
-
