Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.

This patch calls usleep_range() only if retry is to be done.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org (linux-4.8)
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.

Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma.  This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.

The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data.  Attempting to get data before
the probe() caused the problem.

This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.

fixes: 9e0d39d8 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.

Cc: stable@vger.kernel.org
Fixes: 30fc8d13 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Sessions are different from transient objects in that their handles
may not be virtualized (because they're used for some hmac
calculations).  Additionally when a session is context saved, a
vestigial memory remains in the TPM and if it is also flushed, that
will be lost and the session context will refuse to load next time, so
the code is updated to flush only transient objects after a context
save.  Add a separate array (chip->session_tbl) to save and restore
sessions by handle.  Use the failure of a context save or load to
signal that the session has been flushed from the TPM and we can
remove its memory from chip->session_tbl.

Sessions are also isolated during each instance of a tpm space.  This
means that spaces shouldn't be able to see each other's sessions and
is enforced by ensuring that a space user may only refer to sessions
handles that are present in their own chip->session_tbl.  Finally when
a space is closed, all the sessions belonging to it should be flushed
so the handles may be re-used by other spaces.

Note that if we get a session save or load error, all sessions are
effectively flushed.  Even though we restore the session buffer, all
the old sessions will refuse to load after the flush and they'll be
purged from our session memory.  This means that while transient
context handling is still soft in the face of errors, session handling
is hard (any failure of the model means all sessions are lost).

Fixes-from: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Currently the tpm spaces are not exposed to userspace.  Make this
exposure via a separate device, which can now be opened multiple times
because each read/write transaction goes separately via the space.

Concurrency is protected by the chip->tpm_mutex for each read/write
transaction separately.  The TPM is cleared of all transient objects
by the time the mutex is dropped, so there should be no interference
between the kernel and userspace.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Added an ability to virtualize TPM commands into an isolated context
that we call a TPM space because the word context is already heavily
used in the TPM specification. Both the handle areas and bodies (where
necessary) are virtualized.

The mechanism works by adding a new parameter struct tpm_space to the
tpm_transmit() function. This new structure contains the list of virtual
handles and a buffer of page size (currently) for backing storage.

When tpm_transmit() is called with a struct tpm_space instance it will
execute the following sequence:

1. Take locks.
2. Load transient objects from the backing storage by using ContextLoad
   and map virtual handles to physical handles.
3. Perform the transaction.
4. Save transient objects to backing storage by using ContextSave and
   map resulting physical handle to virtual handle if there is such.

This commit does not implement virtualization support for hmac and
policy sessions.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Check for every TPM 2.0 command that the command code is supported and
the command buffer has at least the length that can contain the header
and the handle area.

For ContextSave and FlushContext we mark the body to be part of the
handle area. This gives validation for these commands at zero
cost, including the body of the command.

The more important reason for this is that we can virtualize these
commands in the same way as you would virtualize the handle area of a
command.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Check that the length matches the length reported by the response
header already in tpm_transmit() to improve validation.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Encapsulated crb_wait_for_reg32() so that state changes in other CRB
registers than TPM_CRB_CTRL_REQ_x can be waited.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>

In order to provide access to locality registers, this commits adds
mapping of the head of the CRB registers, which are located right
before the control area.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>

Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.

As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.

Cc: <stable@vger.kernel.org>
Fixes: 0edbfea5 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.

v2: Moved scope of spi_message to the top as requested by Jarkko
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea5 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Wait states are signaled in the last byte received from the TPM in
response to the header, not the first byte. Check rx_buf[3] instead of
rx_buf[0].

Cc: <stable@vger.kernel.org>
Fixes: 0edbfea5 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.

Cc: <stable@vger.kernel.org>
Fixes: 0edbfea5 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.

This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)

v2: u16 instead of u8 for the length.
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea5 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This fix enables a platform to enter the idle state (suspend-to-idle)

The driver needs to request explicitly go_idle upon completion
from the pm suspend handler.
The runtime pm is disabled on suspend during prepare state by calling
pm_runtime_get_noresume, hence we cannot relay on runtime pm to leave
the device in low power state. Symmetrically cmdReady is called
upon resume.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Siged-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

We get a newly introduced harmless warning when CONFIG_CRYPTO is disabled:

warning: (TCG_TPM && TRUSTED_KEYS && IMA) selects CRYPTO_HASH_INFO which has unmet direct dependencies (CRYPTO)

This adds another select to avoid the warning, consistent with other users
of the crypto code.

Fixes: c1f92b4b ("tpm: enhance TPM 2.0 PCR extend to support multiple banks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Commit 500462a9 "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers.  Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration.  The only exception noted to this were
networking timers with a small expiry time.

Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay.  The
non-cascading wheel delay is based on CONFIG_HZ.  For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.

Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.

* HZ 1000 steps
 * Level Offset  Granularity            Range
 *  0      0         1 ms                0 ms - 63 ms
 *  1     64         8 ms               64 ms - 511 ms
 *  2    128        64 ms              512 ms - 4095 ms (512ms - ~4s)

* HZ  250
 * Level Offset  Granularity            Range
 *  0      0         4 ms                0 ms - 255 ms
 *  1     64        32 ms              256 ms - 2047 ms (256ms - ~2s)
 *  2    128       256 ms             2048 ms - 16383 ms (~2s - ~16s)

Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9.

linux-4.7 | msleep() usleep_range()
1000 hz: 0m44.628s | 1m34.497s 29.243s
250 hz: 1m28.510s | 4m49.269s 32.386s

linux-4.7  | min-max (msleep)  min-max (usleep_range)
1000 hz: 0:017 - 2:760s | 0:015 - 3:967s    0:014 - 0:418s
250 hz: 0:028 - 1:954s | 0:040 - 4:096s    0:016 - 0:816s

This patch replaces the msleep() with usleep_range() calls in the
i2c nuvoton driver with a consistent max range value.
Signed-of-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org (linux-4.8)
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The expectation is that the if the CRB cmd/rsp buffer falls within the
ACPI region that the entire buffer will be within the reason. Otherwise
resource reservation will fail when it crosses regions.

Work around this BIOS bug by limiting the cmd/rsp buffer to the length
of the declared ACPI region. BIOS vendors should fix this by making
the ACPI and register length declarations consistent.
Reported-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.

This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.

During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.

Cc: stable@vger.kernel.org
Fixes: aec04cbd ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <james.l.morris@oracle.com>

We switched from "struct task_struct"->security to "struct cred"->security
in Linux 2.6.29. But not all LSM modules were happy with that change.
TOMOYO LSM module is an example which want to use per "struct task_struct"
security blob, for TOMOYO's security context is defined based on "struct
task_struct" rather than "struct cred". AppArmor LSM module is another
example which want to use it, for AppArmor is currently abusing the cred
a little bit to store the change_hat and setexeccon info. Although
security_task_free() hook was revived in Linux 3.4 because Yama LSM module
wanted to release per "struct task_struct" security blob,
security_task_alloc() hook and "struct task_struct"->security field were
not revived. Nowadays, we are getting proposals of lightweight LSM modules
which want to use per "struct task_struct" security blob.

We are already allowing multiple concurrent LSM modules (up to one fully
armored module which uses "struct cred"->security field or exclusive hooks
like security_xfrm_state_pol_flow_match(), plus unlimited number of
lightweight modules which do not use "struct cred"->security nor exclusive
hooks) as long as they are built into the kernel. But this patch does not
implement variable length "struct task_struct"->security field which will
become needed when multiple LSM modules want to use "struct task_struct"->
security field. Although it won't be difficult to implement variable length
"struct task_struct"->security field, let's think about it after we merged
this patch.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: John Johansen <john.johansen@canonical.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Tested-by: Djalal Harouni <tixxdz@gmail.com>
Acked-by: José Bollo <jobol@nonadev.net>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: James Morris <james.l.morris@oracle.com>
Cc: José Bollo <jobol@nonadev.net>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Pull char/misc driver fixes from Greg KH:
 "A smattering of different small fixes for some random driver
  subsystems. Nothing all that major, just resolutions for reported
  issues and bugs.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  extcon: int3496: Set the id pin to direction-input if necessary
  extcon: int3496: Use gpiod_get instead of gpiod_get_index
  extcon: int3496: Add dependency on X86 as it's Intel specific
  extcon: int3496: Add GPIO ACPI mapping table
  extcon: int3496: Rename GPIO pins in accordance with binding
  vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
  ppdev: fix registering same device name
  parport: fix attempt to write duplicate procfiles
  auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
  Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
  Drivers: hv: vmbus: Don't leak channel ids
  Drivers: hv: util: don't forget to init host_ts.lock
  Drivers: hv: util: move waiting for release to hv_utils_transport itself
  vmbus: remove hv_event_tasklet_disable/enable
  vmbus: use rcu for per-cpu channel list
  mei: don't wait for os version message reply
  mei: fix deadlock on mei reset
  intel_th: pci: Add Gemini Lake support
  intel_th: pci: Add Denverton SOC support
  intel_th: Don't leak module refcount on failure to activate
  ...

Merge tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single kernfs fix for 4.11-rc4 that resolves a reported
  issue.

  It has been in linux-next with no reported issues"

* tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: Check KERNFS_HAS_RELEASE before calling kernfs_release_file()

Pull tty/serial driver fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.11-rc4.

  One of these fix a long-standing issue in the ldisc code that was
  found by Dmitry Vyukov with his great fuzzing work. The other fixes
  resolve other reported issues, and there is one revert of a patch in
  4.11-rc1 that wasn't correct.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: fix data race in tty_ldisc_ref_wait()
  tty: don't panic on OOM in tty_set_ldisc()
  Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
  tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
  serial: 8250_dw: Fix breakage when HAVE_CLK=n
  serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios

Pull IIO driver fixes from Greg KH:
 "Here are some small IIO driver fixes for 4.11-rc4 that resolve a
  number of tiny reported issues. All of these have been in linux-next
  for a while with no reported issues"

* tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: imu: st_lsm6dsx: fix FIFO_CTRL2 overwrite during watermark configuration
  iio: adc: ti_am335x_adc: fix fifo overrun recovery
  iio: sw-device: Fix config group initialization
  iio: magnetometer: ak8974: remove incorrect __exit markups
  iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3

Pull USB/PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.11-rc4.

  Nothing major here, just an bunch of small fixes, and a handfull of
  good fixes from Johan for devices with crazy descriptors. There are a
  few new device ids in here as well.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  usb: gadget: f_hid: fix: Don't access hidg->req without spinlock held
  usb: gadget: udc: remove pointer dereference after free
  usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed
  usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval
  usb: gadget: acm: fix endianness in notifications
  usb: dwc3: gadget: delay unmap of bounced requests
  USB: serial: qcserial: add Dell DW5811e
  usb: hub: Fix crash after failure to read BOS descriptor
  ACM gadget: fix endianness in notifications
  USB: usbtmc: fix probe error path
  USB: usbtmc: add missing endpoint sanity check
  USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems
  usb: musb: fix possible spinlock deadlock
  usb: musb: dsps: fix iounmap in error and exit paths
  usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer
  usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk
  uwb: i1480-dfu: fix NULL-deref at probe
  uwb: hwa-rc: fix NULL-deref at probe
  USB: wusbcore: fix NULL-deref at probe
  USB: uss720: fix NULL-deref at probe
  ...

Pull more powerpc fixes from Michael Ellerman:
 "These are all pretty minor. The fix for idle wakeup would be a bad bug
  but has not been observed in practice.

  The update to the gcc-plugins docs was Cc'ed to Kees and Jon, Kees
  OK'ed it going via powerpc and I didn't hear from Jon.

   - cxl: Route eeh events to all slices for pci_channel_io_perm_failure state

   - powerpc/64s: Fix idle wakeup potential to clobber registers

   - Revert "powerpc/64: Disable use of radix under a hypervisor"

   - gcc-plugins: update architecture list in documentation

  Thanks to: Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav
  Jain"

* tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  gcc-plugins: update architecture list in documentation
  Revert "powerpc/64: Disable use of radix under a hypervisor"
  powerpc/64s: Fix idle wakeup potential to clobber registers
  cxl: Route eeh events to all slices for pci_channel_io_perm_failure state

Pull ext4 fixes from Ted Ts'o:
 "Fix a memory leak on an error path, and two races when modifying
  inodes relating to the inline_data and metadata checksum features"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix two spelling nits
  ext4: lock the xattr block before checksuming it
  jbd2: don't leak memory if setting up journal fails
  ext4: mark inode dirty after converting inline directory

Pull fscrypto fixes from Ted Ts'o:
 "A code cleanup and bugfix for fs/crypto"

* tag 'fscrypt-for-linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
  fscrypt: eliminate ->prepare_context() operation
  fscrypt: remove broken support for detecting keyring key revocation

Merge tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - bug fixes in asus_atk0110, it87 and max31790 drivers

 - added missing API definition to hwmon core

* tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (asus_atk0110) fix uninitialized data access
  hwmon: Add missing HWMON_T_ALARM
  hwmon: (it87) Avoid registering the same chip on both SIO addresses
  hwmon: (max31790) Set correct PWM value

Pull rdma fixes from Doug Ledford:
 "This has been a slow -rc cycle for the RDMA subsystem. We really
  haven't had a lot of rc fixes come in. This pull request is the first
  of this entire rc cycle and it has all of the suitable fixes so far
  and it's still only about 20 patches. The fix for the minor breakage
  cause by the dma mapping patchset is in here, as well as a couple
  other potential oops fixes, but the rest is more minor.

  Summary:

   - fix for dma_ops change in this kernel, resolving the s390, powerpc,
     and IOMMU operation

   - a few other oops fixes

   - the rest are all minor fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/qib: fix false-postive maybe-uninitialized warning
  RDMA/iser: Fix possible mr leak on device removal event
  IB/device: Convert ib-comp-wq to be CPU-bound
  IB/cq: Don't process more than the given budget
  IB/rxe: increment msn only when completing a request
  uapi: fix rdma/mlx5-abi.h userspace compilation errors
  IB/core: Restore I/O MMU, s390 and powerpc support
  IB/rxe: Update documentation link
  RDMA/ocrdma: fix a type issue in ocrdma_put_pd_num()
  IB/rxe: double free on error
  RDMA/vmw_pvrdma: Activate device on ethernet link up
  RDMA/vmw_pvrdma: Dont hardcode QP header page
  RDMA/vmw_pvrdma: Cleanup unused variables
  infiniband: Fix alignment of mmap cookies to support VIPT caching
  IB/core: Protect against self-requeue of a cq work item
  i40iw: Receive netdev events post INET_NOTIFIER state

Pull audit fix from Paul Moore:
 "We've got an audit fix, and unfortunately it is big.

  While I'm not excited that we need to be sending you something this
  large during the -rcX phase, it does fix some very real, and very
  tangled, problems relating to locking, backlog queues, and the audit
  daemon connection.

  This code has passed our testsuite without problem and it has held up
  to my ad-hoc stress tests (arguably better than the existing code),
  please consider pulling this as fix for the next v4.11-rcX tag"

* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
  audit: fix auditd/kernel connection state tracking