The Gateworks Ventana GW5904 is a single-board computer based on the NXP
IMX6 SoC with the following features:
 * IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
 * 2048MB DDR3 DRAM (4x64bit) (options up to 4GiB)
 * 8GB eMMC
 * Gateworks System Controller:
  - hardware watchdog
  - hardware monitor
  - pushbutton controller
  - EEPROM storage
  - power control
 * JTAG programmable
 * 1x miniPCIe socket (with PCIe, USB)
 * 1x miniPCIe socket (USB)
 * 1x M.2 socket (USB, 2x SIM)
 * Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
 * GPS (optional uBlox EVA-M8M)
 * Application headers:
  - 2x RS232 UART (TX/RX/CTS/RTS)
  - 8x TTL GPIO (3x configurable as PWM)
  - 1x LVDS display 3D+C with i2c touch and PWM backlight
 * MV88E6176 GbE Switch (uplink to IMX FEC)
 * Front panel connectors:
  - 1x user programmable LED
  - 1x configurable user pushbutton
  - 1x USB OTG
  - 4x GbE LAN
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

System Reset Controller in i.MX7 doesn't have any commonality with IP
block found in i.MX5 and i.MX6 SoC families. Given that and the new
upstream driver for i.MX7 variant (see
https://lkml.org/lkml/2017/2/21/466) remove "fsl,imx51-src" from
compatibility string.

Cc: yurovsky@gmail.com
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add LVDS display support for OpenFrame Capacitive touch 7 inc
display which is supported by Engicam i.CoreM6 QDL Starter Kit.

Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.

General features:
CPU           NXP i.MX6Q rev1.2 at 792 MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
LVDS Display  TFT 12.3" industrial, 1280x480 resolution
Backlight     LED backlight, brightness 350 Cd/m2
Power supply  15 to 30 Vdc

Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.

General features:
CPU           NXP i.MX6Q rev1.2 at 792 MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
LVDS Display  TFT 10.1" industrial, 1280x800 resolution
Backlight     LED backlight, brightness 350 Cd/m2
Power supply  15 to 30 Vdc

Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch add support for lvds backlight on i.CoreM6 QDL
variant boards.

Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Configures the megachips-stdpxxxx-ge-b850v3-fw bridges on the GE
B850v3 dts file.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx7d-sdb has a mickro bus connector that can be connected to a
Sensirion SHT11 click board (temperature and humidity sensor):

https://shop.mikroe.com/click/sensors/sht1x

Add a new device tree file to describe such hardware.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PHYs embedded in the switch direct there interrupts through the
switch interrupt controllers. Now that devel C has its switch
interrupts connected to the SoC, the PHY interrupts can be used by
phylib. Explicitly include MDIO nodes in the switch device tree nodes,
and link the PHY interrupts back to the switch interrupt
controller. Also, link the ports to the PHYs on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The devel B and devel C board use the same GPIO lines for interrupts
from the two switches. Move the pinmux nodes from devel B into the
shared .dtsi file, and wire up the interrupts on devel C.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

UART on i.MX6SX (like all other i.MX6 SoC variants) has the same
programming model as the 'imx6q-uart' type, so add it to the compatible
UART string.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change the maxium spi clock frequency from 20MHz to 10MHz to meet the
operation voltage range requirement recommended in AT25 datasheet.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the reference manuals, both imx50/imx53 SOC seem to share
the same eSDHC controller, especially the section on "Multi-block Read"
mentioned in commit 361b8482 ("mmc: sdhci-esdhc-imx: fix multiblock
reads on i.MX53") is identical for both SOC.
Hence, let imx50 use imx53-esdhc.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable ocotp for i.mx7D/S.
Correct the clock entry and compatible string.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reference them by handle and remove the changed clocks that are copied
from the downstream DT and are not part of the mainline binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Referencing the node by handle make the QP DT more resilent against
changes of the base DT. Also remove the duplicated reg property, it's
not needed as it the same as in the base DT, just the compatible is
actually different.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

By using the handle, we can avoid some duplication of the base DT
and so avoid any maintenance overhead in the QP DT if the referenced
node changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All currently supported i.MX25-based machines use phy_type = "utmi" and
dr_mode = "otg".  So this seems to be a sensible default.

This also doesn't hurt out-of-tree machines because up to now they had
to specify these two properties in the machine.dts which still takes
precedence by just overwriting the defaults added here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This machine is based on I2SE's Duckbill 2 board and is sold as part
of I2SE's PLC Bundle for IoT. This is a development kit for Homeplug
Green PHY based powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the missing devicetree binding documentation for I2SE's
Duckbill and Duckbill 2 series boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
  According to phy datasheet, 25ms are sufficient. This also reduces
  the time to boot the system.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch renames mmc2_sck_cfg in order to prepare for an alternative
muxing setup.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Quoting Philipp Zabel:
"Since this regulator is used as the TVDAC analog power supply, this
range should at least be limited to the analog power supply range of the
TVDAC, listed in Table 74-9. of the i.MX53 reference manual (2.5-2.75V).

But since the nominal voltage is 2.75V, which was used to determine the
analog gain that is supposed to result in the necessary 0.7V
peak-to-peak amplitude on the VGA output, I'd say we should just fix the
voltage to 2750000 here."

, so limit the TVDAC analog power supply as suggested.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul.dtsi already contains:

cpu0: cpu@0 {
	....
	arm-supply = <&reg_arm>;
	soc-supply = <&reg_soc>;
};

, so remove the duplication.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The cm-fx6 module has an onboard Wolfson wm8731 codec which is muxed
to the ssi2 controller. Unlike most (all?) supported i.MX6 board/codec
combinations the wm8731 is operated in slave mode and the clock setup
is static.

Add support for it.
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhanced commit message, ported
  to upstream and some cleanup]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Leave pca953x P06,P07 pins on b850v3 platform and P06 pin on
b450v3/b650v3 unconfigured in the kernel space since they could be
configured as DP1_RST and DP2_RST by the applications for the DP FW
update support.
Signed-off-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...

Pull more KVM updates from Radim Krčmář:
 "Second batch of KVM changes for the 4.11 merge window:

  PPC:
   - correct assumption about ASDR on POWER9
   - fix MMIO emulation on POWER9

  x86:
   - add a simple test for ioperm
   - cleanup TSS (going through KVM tree as the whole undertaking was
     caused by VMX's use of TSS)
   - fix nVMX interrupt delivery
   - fix some performance counters in the guest

  ... and two cleanup patches"

* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Fix pending events injection
  x86/kvm/vmx: remove unused variable in segment_base()
  selftests/x86: Add a basic selftest for ioperm
  x86/asm: Tidy up TSS limit code
  kvm: convert kvm.users_count from atomic_t to refcount_t
  KVM: x86: never specify a sample period for virtualized in_tx_cp counters
  KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
  KVM: PPC: Book3S HV: Fix software walk of guest process page tables

Pull documentation fixes from Jonathan Corbet:
 "A few fixes for the docs tree, including one for a 4.11 build
  regression"

* tag 'docs-4.11-fixes' of git://git.lwn.net/linux:
  Documentation/sphinx: fix primary_domain configuration
  docs: Fix htmldocs build failure
  doc/ko_KR/memory-barriers: Update control-dependencies section
  pcieaer doc: update the link
  Documentation: Update path to sysrq.txt

Pull staging/IIO driver fixes from Greg KH:
 "Here are a few small staging and IIO driver fixes for issues that
  showed up after the big set if changes you merged last week.

  Nothing major, just small bugs resolved in some IIO drivers, a lustre
  allocation fix, and some RaspberryPi driver fixes for reported
  problems, as well as a MAINTAINERS entry update.

  All of these have been in linux-next for a week with no reported
  issues"

* tag 'staging-4.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: fsl-mc: fix warning in DT ranges parser
  MAINTAINERS: Remove Noralf Trønnes as fbtft maintainer
  staging: vchiq_2835_arm: Make cache-line-size a required DT property
  staging: bcm2835/mmal-vchiq: unlock on error in buffer_from_host()
  staging/lustre/lnet: Fix allocation size for sv_cpt_data
  iio: adc: xilinx: Fix error handling
  iio: 104-quad-8: Fix off-by-one error when addressing flag register
  iio: adc: handle unknow of_device_id data

Pull crypto fixes from Herbert Xu:

 - vmalloc stack regression in CCM

 - Build problem in CRC32 on ARM

 - Memory leak in cavium

 - Missing Kconfig dependencies in atmel and mediatek

 - XTS Regression on some platforms (s390 and ppc)

 - Memory overrun in CCM test vector

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: vmx - Use skcipher for xts fallback
  crypto: vmx - Use skcipher for cbc fallback
  crypto: testmgr - Pad aes_ccm_enc_tv_template vector
  crypto: arm/crc32 - add build time test for CRC instruction support
  crypto: arm/crc32 - fix build error with outdated binutils
  crypto: ccm - move cbcmac input off the stack
  crypto: xts - Propagate NEED_FALLBACK bit
  crypto: api - Add crypto_requires_off helper
  crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
  crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
  crypto: cavium - fix leak on curr if curr->head fails to be allocated
  crypto: cavium - Fix couple of static checker errors

Pull misc final vfs updates from Al Viro:
 "A few unrelated patches that got beating in -next.

  Everything else will have to go into the next window ;-/"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  hfs: fix hfs_readdir()
  selftest for default_file_splice_read() infoleak
  9p: constify ->d_name handling

Pull more SCSI updates from James Bottomley:
 "This is the set of stuff that didn't quite make the initial pull and a
  set of fixes for stuff which did.

  The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
  cover a lot of previously submitted stuff, the most important of which
  probably covers some of the failing irq vectors allocation and other
  fallout from having the SCSI command allocated as part of the block
  allocation functions"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
  scsi: qedi: Fix memory leak in tmf response processing.
  scsi: aacraid: remove redundant zero check on ret
  scsi: lpfc: use proper format string for dma_addr_t
  scsi: lpfc: use div_u64 for 64-bit division
  scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
  scsi: cciss: correct check map error.
  scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
  scsi: aacraid: Fixed expander hotplug for SMART family
  scsi: mpt3sas: switch to pci_alloc_irq_vectors
  scsi: qedf: fixup compilation warning about atomic_t usage
  scsi: remove scsi_execute_req_flags
  scsi: merge __scsi_execute into scsi_execute
  scsi: simplify scsi_execute_req_flags
  scsi: make the sense header argument to scsi_test_unit_ready mandatory
  scsi: sd: improve TUR handling in sd_check_events
  scsi: always zero sshdr in scsi_normalize_sense
  scsi: scsi_dh_emc: return success in clariion_std_inquiry()
  scsi: fix memory leak of sdpk on when gd fails to allocate
  scsi: sd: make sd_devt_release() static
  scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
  ...

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>