- 01 Dec, 2022 38 commits
-
-
Ryder Lee authored
Correct mac timiing settings for different hardware generations. This improves 40-60Mbps performance. Fixes: 9aac2969 ("mt76: mt7915: update mac timing settings") Reported-By:
Carson Vandegriffe <carson.vandegriffe@candelatech.com> Tested-by:
Chad Monroe <chad.monroe@smartrg.com> Signed-off-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
Felix Fietkau <nbd@nbd.name>
-
Shayne Chen authored
For MT7915D, correct antenna index should be set to let DFS radar detection work on the 5 GHz band. Signed-off-by:
Shayne Chen <shayne.chen@mediatek.com> Signed-off-by:
-
Shayne Chen authored
In previous, we only allow user to configure tx antenna mask contiguously (e.g. 0x3, 0xf). This patch allows user to configure tx antenna mask interleavingly (e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can prioritized the signal of different antennas, which helps to test their performance in normal mode. Signed-off-by:
-
Shayne Chen authored
Add mt76_connac_spe_idx() for antenna mask to spatial extension index conversion. This is used to support flexible control of tx antenna. Signed-off-by:
-
Shayne Chen authored
Let the configuration of testmode antenna mask on both band0 and band1 become antenna_mask rather than chainmask. This could simplify the settings for user and get rid of the conversion when sending fw command. Signed-off-by:
-
Peter Chiu authored
A variant of mt7916 supports up to 3 tx/rx paths but with only 2 spatial streams. An example usage of the 3rd path is to server as an auxiliary for beamforming. In order to deal with this case, this patch reworks some parts to correctly use paths or streams. Signed-off-by:
Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by:
-
Shayne Chen authored
Rework tx paths and streams init part to improve readability, and make sure that the available tx streams should be smaller than or equal to the available tx paths. Signed-off-by:
-
Evelyn Tsai authored
The value of regidx of rf registers is combined with WF selection and offset. Extend the WF selection field from 4 to 8 bits since the adie index should also be specified. Signed-off-by:
Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by:
-
Ben Greear authored
According to the tx-free-done documentation, the DW4 can be repeated, so have to be more careful about how we test for walking off the end of the array. Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Gaosheng Cui authored
All uses of mt76_wcid_mask_test() have been removed since commit 8950a62f ("mt76: get rid of mt76_wcid_hw routine"), so remove it. Signed-off-by:
Gaosheng Cui <cuigaosheng1@huawei.com> Signed-off-by:
-
Sean Wang authored
Group 3 in RxD is disabled in monitor mode. We should use the group 5 in RxD instead to fix antenna signal way off issue, e.g we would see the incorrect antenna signal value in wireshark. On the other hand, Group 5 wouldn't be used in STA or AP mode, so the patch shouldn't cause any harm to those modes. Fixes: cbaa0a40 ("mt76: mt7921: fix up the monitor mode") Reported-by:
Adrian Granados <agranados@gmail.com> Co-developed-by:
Deren Wu <deren.wu@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Felix Fietkau authored
- remove stbc, because mt76x0 doesn't support it and mt76x2 uses the same values as HT/VHT - reduce vht array to 2 elements, because VHT MCS0-7 are the same as HT Signed-off-by: -
Felix Fietkau authored
Its layout and code is mt76x02 specific Signed-off-by: -
Felix Fietkau authored
ieee80211_drop_unencrypted is called from ieee80211_rx_h_mesh_fwding and ieee80211_frame_allowed. Since ieee80211_rx_h_mesh_fwding can forward packets for other mesh nodes and is called earlier, it needs to check the decryptions status and if the packet is using the control protocol on its own, instead of deferring to the later call from ieee80211_frame_allowed. Because of that, ieee80211_drop_unencrypted has a mesh specific check that skips over the mesh header in order to check the payload protocol. This code is invalid when called from ieee80211_frame_allowed, since that happens after the 802.11->802.3 conversion. Fix this by moving the mesh specific check directly into ieee80211_rx_h_mesh_fwding. Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Felix Fietkau authored
This can be used to selectively disable feature flags for checksum offload, scatter/gather or GSO by changing vif->netdev_features. Removing features from vif->netdev_features does not affect the netdev features themselves, but instead fixes up skbs in the tx path so that the offloads are not needed in the driver. Aside from making it easier to deal with vif type based hardware limitations, this also makes it possible to optimize performance on hardware without native GSO support by declaring GSO support in hw->netdev_features and removing it from vif->netdev_features. This allows mac80211 to handle GSO segmentation after the sta lookup, but before itxq enqueue, thus reducing the number of unnecessary sta lookups, as well as some other per-packet processing. Signed-off-by:
-
Kieran Frewen authored
Updates to the TIM information element to match changes made in the IEEE Std 802.11ah-2020. Signed-off-by:
Kieran Frewen <kieran.frewen@morsemicro.com> Co-developed-by:
Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com> Signed-off-by:
-
Johannes Berg authored
It's not valid to have the multiple BSSID element in the association response (per 802.11 REVme D1.0), so don't try to parse it there, but only in the fallback beacon elements if needed. The other case that was parsing association requests was already changed in a previous commit. Change-Id: I659d2ef1253e079cc71c46a017044e116e31c024 Signed-off-by: -
Johannes Berg authored
There's no need to open-code container_of() when we have bss_from_pub(). Use it. Change-Id: I074723717909ba211a40e6499f0c36df0e2ba4be Signed-off-by: -
Johannes Berg authored
The call to ieee80211_do_stop() right after will also do synchronize_rcu() to ensure the SDATA_STATE_RUNNING bit is cleared, so we don't need to synchronize_net() here. Change-Id: Id9f9ffcf195002013e5d9fde288877d219780864 Signed-off-by: -
Alexander Wetzel authored
ieee80211_get_txq() can only be called with vif != NULL. Remove not needed NULL test in function. Signed-off-by:
Alexander Wetzel <alexander@wetzel-home.de> Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/20221107161328.2883-1-alexander@wetzel-home.deSigned-off-by:
-
Chen Zhongjin authored
In regulatory_init_db(), when it's going to return a error, reg_pdev should be unregistered. When load_builtin_regdb_keys() fails it doesn't do it and makes cfg80211 can't be reload with report: sysfs: cannot create duplicate filename '/devices/platform/regulatory.0' ... <TASK> dump_stack_lvl+0x79/0x9b sysfs_warn_dup.cold+0x1c/0x29 sysfs_create_dir_ns+0x22d/0x290 kobject_add_internal+0x247/0x800 kobject_add+0x135/0x1b0 device_add+0x389/0x1be0 platform_device_add+0x28f/0x790 platform_device_register_full+0x376/0x4b0 regulatory_init+0x9a/0x4b2 [cfg80211] cfg80211_init+0x84/0x113 [cfg80211] ... Fixes: 90a53e44 ("cfg80211: implement regdb signature checking") Signed-off-by:
Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221109090237.214127-1-chenzhongjin@huawei.comSigned-off-by:
-
JUN-KYU SHIN authored
If the "channel->freq_offset" comparison is omitted in cmp_bss(), BSS with different kHz units cannot be distinguished in the S1G Band. So "freq_offset" should also be included in the comparison. Signed-off-by:
JUN-KYU SHIN <jk.shin@newratek.com> Link: https://lore.kernel.org/r/20221111023301.6395-1-jk.shin@newratek.comSigned-off-by:
-
Íñigo Huguet authored
In ieee80211_lookup_key, the variable named `local` is unused if compiled without lockdep, getting this warning: net/mac80211/cfg.c: In function ‘ieee80211_lookup_key’: net/mac80211/cfg.c:542:26: error: unused variable ‘local’ [-Werror=unused-variable] struct ieee80211_local *local = sdata->local; ^~~~~ Fix it with __maybe_unused. Fixes: 8cbf0c2a ("wifi: mac80211: refactor some key code") Signed-off-by:Íñigo Huguet <ihuguet@redhat.com> Link: https://lore.kernel.org/r/20221111153622.29016-1-ihuguet@redhat.comSigned-off-by:
-
Philipp Hortmann authored
Correct wrong closing bracket. Signed-off-by:
Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/20221114200135.GA100176@matrix-ESPRIMO-P710Signed-off-by:
-
Zhengchao Shao authored
When register_netdevice() failed in ieee80211_if_add(), ndev->tstats isn't released. Fix it. Fixes: 5a490510 ("mac80211: use per-CPU TX/RX statistics") Signed-off-by:
Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221117064500.319983-1-shaozhengchao@huawei.comSigned-off-by:
-
Yuan Can authored
As the nla_nest_start() may fail with NULL returned, the return value needs to be checked. Fixes: ce08cd34 ("wifi: nl80211: expose link information for interfaces") Signed-off-by:
Yuan Can <yuancan@huawei.com> Link: https://lore.kernel.org/r/20221129014211.56558-1-yuancan@huawei.comSigned-off-by:
-
Kees Cook authored
When building with -Wstringop-overflow, GCC's KASAN implementation does not correctly perform bounds checking within some complex structures when faced with literal offsets, and can get very confused. For example, this warning is seen due to literal offsets into sturct ieee80211_hdr that may or may not be large enough: drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c: In function 'iwl_mvm_rx_mpdu_mq': drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c:2022:29: warning: writing 1 byte into a region of size 0 [-Wstringop-overflow=] 2022 | *qc &= ~IEEE80211_QOS_CTL_A_MSDU_PRESENT; In file included from drivers/net/wireless/intel/iwlwifi/mvm/fw-api.h:32, from drivers/net/wireless/intel/iwlwifi/mvm/sta.h:15, from drivers/net/wireless/intel/iwlwifi/mvm/mvm.h:27, from drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c:10: drivers/net/wireless/intel/iwlwifi/mvm/../fw/api/rx.h:559:16: note: at offset [78, 166] into destination object 'mpdu_len' of size 2 559 | __le16 mpdu_len; | ^~~~~~~~ Refactor ieee80211_get_qos_ctl() to avoid using literal offsets, requiring the creation of the actual structure that is described in the comments. Explicitly choose the desired offset, making the code more human-readable too. This is one of the last remaining warning to fix before enabling -Wstringop-overflow globally. Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=97490 Link: https://github.com/KSPP/linux/issues/181 Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Kalle Valo <kvalo@kernel.org> Cc: Gregory Greenman <gregory.greenman@intel.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20221130212641.never.627-kees@kernel.orgSigned-off-by:
-
Zong-Zhe Yang authored
First, introduce struct rtw89_sub_entity for chanctx related stuffs. Second, add enum rtw89_sub_entity_idx to rtw89_vif for vif operation to access its/right chanctx stuffs after future multi-channel support. Besides, RTW89_SUB_ENTITY_0 is the default chanctx entry throughout driver, i.e. it's used for things which may not have a target chanctx yet. So, we need to ensure that RTW89_SUB_ENTITY_0 is always working. If there is at least one alive chanctx, then one of them must take RTW89_SUB_ENTITY_0. If no alive chanctx, RTW89_SUB_ENTITY_0 will be filled by rtw89_config_default_chandef(). Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221129083130.45708-7-pkshih@realtek.com
-
Zong-Zhe Yang authored
These MCC H2C(s) require to wait for MCC C2H to determine if the execution is successful. Through rtw89_wait_for_cond(), we make them wait for either a completion with data from MCC C2H handlers, which calls rtw89_complete_cond(), or timeout. Signed-off-by:
-
Zong-Zhe Yang authored
Process C2H(s) related to MCC (multi-channel concurrency). These handling, which either call rtw89_complete_cond() or show message in debug mode, can be considered atomic/lock-free. So, they should be safe to be processed directly after C2H pre-check in previous patch. Signed-off-by:
-
Zong-Zhe Yang authored
MCC (multi-channel concurrency) related H2Cs (host to chip commands) require to wait for C2H (chip to host events) responses to judge the execution result and data. We introduce helpers to assist this process. Besides, we would like the helpers to be generic for use in driver even outside of MCC H2C/C2H, so we make a independent patch for them. In the following, I describe the things first. ``` (A) C2H is generated by FW, and then transferred upto driver. Hence, driver cannot get it immediately without a bit waitting/blocking. For this, we choose to use wait_for_completion_*() instead of busy polling. (B) From the driver management perspective, a scenario, e.g. MCC, may have mulitple kind of H2C functions requiring this process to wait for corresponding C2Hs. But, the driver management flow uses mutex to protect each behavior. So, one scenario triggers one H2C function at one time. To avoid rampant instances of struct completion for each H2C function, we choose to use one struct completion with one condition flag for one scenario. (C) C2Hs, which H2Cs will be waitting for, cannot be ordered with driver management flow, i.e. cannot enqueue work to the same ordered workqueue and cannot lock by the same mutex, to prevent H2C side from getting no C2H responses. So, those C2Hs are parsed in interrupt context directly as done in previous commit. (D) Following (C), the above underline H2Cs and C2Hs will be handled in different contexts without sync. So, we use atomic_cmpxchg() to compare and change the condition in atomic. ``` So, we introduce struct rtw89_wait_info which combines struct completion and atomic_t. Then, the below are the descriptions for helper functions. * rtw89_wait_for_cond() to wait for a completion based on a condition. * rtw89_complete_cond() to complete a given condition and carry data. Each rtw89_wait_info instance independently determines the meaning of its waitting conditions. But, RTW89_WAIT_COND_IDLE (UINT_MAX) is reserved. Signed-off-by:
-
Zong-Zhe Yang authored
Before queuing C2H work, we check atomicity of the C2H's handler first now. If atomic or lock-free, handle it directly; otherwise, handle it with mutex in work as previous. This prepares for MAC MCC C2Hs which require to be processed directly. And, their handlers will be functions which can be considered atomic. Signed-off-by:
-
Zong-Zhe Yang authored
The `rtw89_mcc_info mcc` is only for RFK MCC stuffs instead of common MCC management info. Replace it with `rtw89_rfk_mcc_info rfk_mcc` to avoid confusion and reserve `struct rtw89_mcc_info mcc` for MCC management code. (No logic changes.) Signed-off-by:
-
Ping-Ke Shih authored
8821ce is a combo card, and BT is a USB device that could get card lost during stress test, and need WiFi firmware to detect and recover it, so driver sends a H2C to enable this mechanism. Signed-off-by:
-
Ping-Ke Shih authored
PoP stands for Packet on Packet that can improve performance in noisy environment, but it could get RX stuck suddenly. In normal mode, firmware can help to resolve the stuck, but firmware doesn't work in monitor mode. Therefore, turn off PoP to avoid RX stuck. Signed-off-by:
-
Ping-Ke Shih authored
With basic HE radiotap, we can check data rate in sniffer data. To store the radiotap data, we reserve headroom of aligned 64 bytes, and then update HE radiotap in monitor mode, so it doesn't affect performance in normal mode. Signed-off-by:
-
Zong-Zhe Yang authored
For running with mac80211 channel context ops and using only as monitor, we need to enable WANT_MONITOR_VIF to let mac80211 process virtual monitor interface. Then, we are able to set channel on the monitor from user space. Signed-off-by:
-
Minsuk Kang authored
This patch fixes slab-out-of-bounds reads in brcmfmac that occur in brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count value of channel specifications provided by the device is greater than the length of 'list->element[]', decided by the size of the 'list' allocated with kzalloc(). The patch adds checks that make the functions free the buffer and return -EINVAL if that is the case. Note that the negative return is handled by the caller, brcmf_setup_wiphybands() or brcmf_cfg80211_attach(). Found by a modified version of syzkaller. Crash Report from brcmf_construct_chaninfo(): ================================================================== BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430 Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896 CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d print_address_description.constprop.0.cold+0x93/0x334 kasan_report.cold+0x83/0xdf brcmf_setup_wiphybands+0x1238/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 Allocated by task 1896: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 kmem_cache_alloc_trace+0x19e/0x330 brcmf_setup_wiphybands+0x290/0x1430 brcmf_cfg80211_attach+0x2118/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888115f24000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1536 bytes inside of 2048-byte region [ffff888115f24000, ffff888115f24800) Memory state around the buggy address: ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Crash Report from brcmf_enable_bw40_2g(): ================================================================== BUG: KASAN: slab-out-of-bounds in brcmf_cfg80211_attach+0x3d11/0x3fd0 Read of size 4 at addr ffff888103787600 by task kworker/0:2/1896 CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x57/0x7d print_address_description.constprop.0.cold+0x93/0x334 kasan_report.cold+0x83/0xdf brcmf_cfg80211_attach+0x3d11/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 Allocated by task 1896: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 kmem_cache_alloc_trace+0x19e/0x330 brcmf_cfg80211_attach+0x3302/0x3fd0 brcmf_attach+0x389/0xd40 brcmf_usb_probe+0x12de/0x1690 usb_probe_interface+0x25f/0x710 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_set_configuration+0x984/0x1770 usb_generic_driver_probe+0x69/0x90 usb_probe_device+0x9c/0x220 really_probe+0x1be/0xa90 __driver_probe_device+0x2ab/0x460 driver_probe_device+0x49/0x120 __device_attach_driver+0x18a/0x250 bus_for_each_drv+0x123/0x1a0 __device_attach+0x207/0x330 bus_probe_device+0x1a2/0x260 device_add+0xa61/0x1ce0 usb_new_device.cold+0x463/0xf66 hub_event+0x10d5/0x3330 process_one_work+0x873/0x13e0 worker_thread+0x8b/0xd10 kthread+0x379/0x450 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff888103787000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1536 bytes inside of 2048-byte region [ffff888103787000, ffff888103787800) Memory state around the buggy address: ffff888103787500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888103787580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888103787600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888103787680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888103787700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Reported-by:Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by:
Jisoo Jang <jisoo.jang@yonsei.ac.kr> Reported-by:
Minsuk Kang <linuxlovemin@yonsei.ac.kr> Reviewed-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
- 28 Nov, 2022 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v6.2. Major changes: ath10k * store WLAN firmware version in SMEM image table
-
Ji-Pin Jou authored
For SDIO/USB interface, since the tranferring speed is slower than that in PCIE, it may have race condition when the driver sets down H2C command to the FW. In the function rtw_fw_send_h2c_command, before the patch, box_reg is written first, then box_ex_reg is written. FW starts to work and fetch the value of box_ex_reg, when the most significant byte of box_reg(4 bytes) is written. Meanwhile, for SDIO/USB interface, since the transferring speed is slow, the driver is still in writing the new value of box_ex_reg through the bus, and FW may get the wrong value of box_ex_reg at the moment. To prevent the above driver/FW racing situation, box_ex_reg is written first then box_reg. Furthermore, it is written in 4 bytes at a time, instead of written in one byte one by one. It can increase the speed for SDIO/USB interface. Signed-off-by:
Ji-Pin Jou <neo_jou@realtek.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
