On Chuwi Hi10 Plus, the Silead device id is MSSL0017.
Signed-off-by: Daniel Smith <danct12@disroot.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Adding 2 new touchpad PNPIDs to enable middle button support.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Notify the PM core that this device is the wake source. This helps
userspace daemon tracking the wake sources to identify the origin of the
wake.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 5.2 merge window.

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/input/serio/libps2.c: In function ‘ps2_handle_ack’:
drivers/input/serio/libps2.c:407:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (ps2dev->flags & PS2_FLAG_NAK) {
      ^
drivers/input/serio/libps2.c:417:2: note: here
  case 0x00:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add initial support for the AT42QT1050 (QT1050) device. The device
supports up to five input keys, dependent on the mode. Since it adds only
the initial support, the "1 to 4 keys plus Guard Channel" mode isn't
supported.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds support for the Azoteq IQS550/572/525 family of
trackpad/touchscreen controllers.

The driver has been tested with an IQS550EV02 evaluation board. A
demonstration of the driver's capabilities is available here:

https://youtu.be/sRNNx4XZBtsSigned-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Provide a simple driver for GPIO controllable vibrators.
It will be used by the Fairphone 2.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Currently any changed config register values don't take effect, as the
function to write them back is called with the wrong register offset.

Fixes: ff8f8370 (Input: synaptics-rmi4 - add support for 2D
                     sensors and F11)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Do not enumerate all formats, some of which the device may not even
support. Instead, only report the one fixed format of the currently
selected input that will survive try_fmt/s_fmt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver doesn't set an initial video format until s_input is called:

  $ v4l2-ctl -d /dev/v4l-touch0 --get-input
  Video input : 0 (Normalized 16-Bit Image: ok)
  $ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
  	Width/Height      : 0/0
  	Pixel Format      : ''
  	[...]
  $ v4l2-ctl -d /dev/v4l-touch0 --set-input 0
  Video input set to 0 (Normalized 16-Bit Image: Touch, ok)
  $ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
  	Width/Height      : 71/40
  	Pixel Format      : 'TD16'
  	[...]

To fix this, initialize the video format to input 0 during probe.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

HUTRR56 defined a new usage code on consumer page to cycle through
set of keyboard layouts, let's add this mapping.
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The HID usage tables define a key to cycle through a set of keyboard
layouts, let's add corresponding keycode.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The SNVS power key is not only used on i.MX6SX and i.MX7D, it is also
used by i.MX6UL and NXP's latest ARMv8 based i.MX8M series SOC. So
update the config dependency to use ARCH_MXC, and add the COMPILE_TEST
too.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Joseph Salisbury <joseph.salisbury@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The OLPC XO-1.75 and XO-4 are ARM-based laptops, using the Marvell
MMP architecture, so don't present this driver on other architectures
except for build-testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Allwinner A83T SoC has a low res adc like the one in Allwinner A10 SoC,
however, the A10 SoC's vref of lradc internally is divided by 2/3 and
the A83T SoC's vref of lradc internally is divided by 3/4, thus add
a hardware variant for it to be compatible with various devices.
Signed-off-by: Ziping Chen <techping.chan@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

With calling dev_pm_set_wake_irq() to set SNVS ON/OFF button
as wakeup source for suspend, generic wake irq mechanism
will automatically enable it as wakeup source when suspend,
then the enable_irq_wake()/disable_irq_wake() can be removed
in suspend/resume callback, it simplifies the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The keypad controller on NXP LPC32xx requires its clock gate to be open,
therefore add description of the requires 'clocks' property.

In addition adjust the example by adding description of required 'clocks'
property and by fixing 'interrupts' property.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of signalling wakeup directly from i8042, let psmouse and atkbd
drivers execute basic protocol handling and only then signal wakeup
condition. This solves the issue where we increment wakeup counter
simply because we are getting responses from keyboard/mouse to the
commands we ourselves send to them as part of suspend transition.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

SNVS IRQ is requested before necessary driver data initialized,
if there is a pending IRQ during driver probe phase, kernel
NULL pointer panic will occur in IRQ handler. To avoid such
scenario, just initialize necessary driver data before enabling
IRQ. This patch is inspired by NXP's internal kernel tree.

Fixes: d3dc6e23 ("input: keyboard: imx: add snvs power key driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

GT5663 is capacitive touch controller with customized smart
wakeup gestures.

Add support for it by adding compatible and supported chip data.

The chip data on GT5663 is similar to GT1151, like
- config data register has 0x8050 address
- config data register max len is 240
- config data checksum has 16-bit
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Goodix CTP controllers require AVDD28, VDDIO regulators for power-on
sequence.

The delay between these regualtor operations as per Power-on Timing
from datasheet[1] is 0 (T1 >= 0 usec).

So, enable and disable these regulators in proper order using normal
regulator functions without any delay in between.

[1] GT5663 Datasheet_English_20151106_Rev.01
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to HUT 1.12 usage 0xb5 from the generic desktop page is reserved
for switching between external and internal display, so let's add the
mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to HUT 1.12 usage 0x232 from the consumer page is reserved for
switching application between full screen and windowed mode, so let's add
the mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to HUTRR73 usages 0x79, 0x7a and 0x7c from the consumer page
correspond to Brightness Up/Down/Toggle keys, so let's add the mappings.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to HUTRR77 usage 0x29f from the consumer page is reserved for
the Desktop application to present all running user’s application windows.
Linux defines KEY_SCALE to request Compiz Scale (Expose) mode, so let's
add the mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to HUTRR37 usage 0x6d from the consumer usage page corresponds
to action that selects the next available supported aspect ratio option
on a device which outputs or displays video. However KEY_ZOOM means
activate "Full Screen" mode, KEY_ASPECT_RATIO should be used instead.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We defined better names for keys to activate full screen mode or
change aspect ratio (while keeping the existing keycodes to avoid
breaking userspace), so let's use them in the document.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It is hard to say what KEY_SCREEN and KEY_ZOOM mean, but historically DVB
folks have used them to indicate switch to full screen mode. Later, they
converged on using KEY_ZOOM to switch into full screen mode and KEY)SCREEN
to control aspect ratio (see Documentation/media/uapi/rc/rc-tables.rst).

Let's commit to these uses, and define:

- KEY_FULL_SCREEN (and make KEY_ZOOM its alias)
- KEY_ASPECT_RATIO (and make KEY_SCREEN its alias)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are many Lenovo laptops which need elan_i2c support, this patch adds
relevant IDs to the Elan driver so that touchpads are recognized.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Tablet initially begins communicating at 9600 baud, so this command
should be used to connect to the device:

    $ inputattach --daemon --baud 9600 --wacom_iv /dev/ttyS0

https://github.com/linuxwacom/xf86-input-wacom/issues/40Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Lenovo s21e-20 uses ELAN0601 in its ACPI tables for the Elan touchpad.
Signed-off-by: Vincent Batts <vbatts@hashbangbash.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When CONFIG_INPUT_POLLDEV is disabled, we get a link error:

drivers/input/touchscreen/raspberrypi-ts.o: In function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0xec): undefined reference to `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0xec): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0x19c): undefined reference to `input_register_polled_device'
raspberrypi-ts.c:(.text+0x19c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `input_register_polled_device'

Select that symbol like we do from the other similar drivers.

Fixes: 0b9f28fe ("Input: add official Raspberry Pi's touchscreen driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When CONFIG_GPIOLIB is not set, we get a couple of build
errors during test building:

drivers/input/misc/msm-vibrator.c: In function 'msm_vibrator_start':
drivers/input/misc/msm-vibrator.c:79:3: error: implicit declaration of function 'gpiod_set_value_cansleep'; did you mean 'gpio_set_value_cansleep'? [-Werror=implicit-function-declaration]
   gpiod_set_value_cansleep(vibrator->enable_gpio, 1);
   ^~~~~~~~~~~~~~~~~~~~~~~~
   gpio_set_value_cansleep
drivers/input/misc/msm-vibrator.c: In function 'msm_vibrator_probe':
drivers/input/misc/msm-vibrator.c:176:26: error: implicit declaration of function 'devm_gpiod_get'; did you mean 'devm_gpio_free'? [-Werror=implicit-function-declaration]
  vibrator->enable_gpio = devm_gpiod_get(&pdev->dev, "enable",
                          ^~~~~~~~~~~~~~
                          devm_gpio_free
drivers/input/misc/msm-vibrator.c:177:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
             GPIOD_OUT_LOW);
             ^~~~~~~~~~~~~
             GPIOF_INIT_LOW
drivers/input/misc/msm-vibrator.c:177:13: note: each undeclared identifier is reported only once for each function it appears in

This is easy to avoid when we use gpio/consumer.h as the documented interface.

Fixes: 0f681d09 ("Input: add new vibrator driver for various MSM SOCs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Reduce size of duplicated comments by switching to use SPDX identifier.

No functional change.

While here, correct MODULE_LICENSE() string to be aligned with license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

ACPI allows to enumerate specific devices by using compatible strings.
Enable that enumeration for EDT touchscreen devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 5.1 merge window.