Calling platform_device_add_properties() replaces existing properties so
the "linux,sysdev_is_parent" property doesn't get set. Add this property
to each platform.

Fixes: d64ff406 ("usb: dwc3: use bus->sysdev for DMA configuration")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Now races can happen between interrupt handler execution and PM runtime in
error handling code path in probe and in dwc3_omap_remove() which will lead
to system crash:

in probe:
...
 err1:
	pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
   due to extcon
	pm_runtime_disable(dev);

	return ret;

in dwc3_omap_remove:
...
	dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
	of_platform_depopulate(omap->dev);
	pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
	pm_runtime_disable(&pdev->dev);

	return 0;

So, OMAP DWC3 IRQ need to be disabled before calling
pm_runtime_put() in probe and in dwc3_omap_remove().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The dev_config() routine in gadgetfs has a check that
dev->dev->bNumConfigurations is equal to 1, and then contains a
redundant line of code setting the value to 1.  This patch removes the
unnecessary assignment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Andrey Konovalov's fuzz testing of gadgetfs showed that we should
improve the driver's checks for valid configuration descriptors passed
in by the user.  In particular, the driver needs to verify that the
wTotalLength value in the descriptor is not too short (smaller
than USB_DT_CONFIG_SIZE).  And the check for whether wTotalLength is
too large has to be changed, because the driver assumes there is
always enough room remaining in the buffer to hold a device descriptor
(at least USB_DT_DEVICE_SIZE bytes).

This patch adds the additional check and fixes the existing check.  It
may do a little more than strictly necessary, but one extra check
won't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Andrey Konovalov reports that fuzz testing with syzkaller causes a
KASAN use-after-free bug report in gadgetfs:

BUG: KASAN: use-after-free in gadgetfs_setup+0x208a/0x20e0 at addr ffff88003dfe5bf2
Read of size 2 by task syz-executor0/22994
CPU: 3 PID: 22994 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 ffff88006df06a18 ffffffff81f96aba ffffffffe0528500 1ffff1000dbe0cd6
 ffffed000dbe0cce ffff88006df068f0 0000000041b58ab3 ffffffff8598b4c8
 ffffffff81f96828 1ffff1000dbe0ccd ffff88006df06708 ffff88006df06748
Call Trace:
 <IRQ> [  201.343209]  [<     inline     >] __dump_stack lib/dump_stack.c:15
 <IRQ> [  201.343209]  [<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159
 [<     inline     >] print_address_description mm/kasan/report.c:197
 [<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286
 [<     inline     >] kasan_report mm/kasan/report.c:306
 [<ffffffff817e562a>] __asan_report_load_n_noabort+0x3a/0x40 mm/kasan/report.c:337
 [<     inline     >] config_buf drivers/usb/gadget/legacy/inode.c:1298
 [<ffffffff8322c8fa>] gadgetfs_setup+0x208a/0x20e0 drivers/usb/gadget/legacy/inode.c:1368
 [<ffffffff830fdcd0>] dummy_timer+0x11f0/0x36d0 drivers/usb/gadget/udc/dummy_hcd.c:1858
 [<ffffffff814807c1>] call_timer_fn+0x241/0x800 kernel/time/timer.c:1308
 [<     inline     >] expire_timers kernel/time/timer.c:1348
 [<ffffffff81482de6>] __run_timers+0xa06/0xec0 kernel/time/timer.c:1641
 [<ffffffff814832c1>] run_timer_softirq+0x21/0x80 kernel/time/timer.c:1654
 [<ffffffff84f4af8b>] __do_softirq+0x2fb/0xb63 kernel/softirq.c:284

The cause of the bug is subtle.  The dev_config() routine gets called
twice by the fuzzer.  The first time, the user data contains both a
full-speed configuration descriptor and a high-speed config
descriptor, causing dev->hs_config to be set.  But it also contains an
invalid device descriptor, so the buffer containing the descriptors is
deallocated and dev_config() returns an error.

The second time dev_config() is called, the user data contains only a
full-speed config descriptor.  But dev->hs_config still has the stale
pointer remaining from the first call, causing the routine to think
that there is a valid high-speed config.  Later on, when the driver
dereferences the stale pointer to copy that descriptor, we get a
use-after-free access.

The fix is simple: Clear dev->hs_config if the passed-in data does not
contain a high-speed config descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Andrey Konovalov reports that fuzz testing with syzkaller causes a
KASAN warning in gadgetfs:

BUG: KASAN: slab-out-of-bounds in dev_config+0x86f/0x1190 at addr ffff88003c47e160
Write of size 65537 by task syz-executor0/6356
CPU: 3 PID: 6356 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 ffff88003c107ad8 ffffffff81f96aba ffffffff3dc11ef0 1ffff10007820eee
 ffffed0007820ee6 ffff88003dc11f00 0000000041b58ab3 ffffffff8598b4c8
 ffffffff81f96828 ffffffff813fb4a0 ffff88003b6eadc0 ffff88003c107738
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159
 [<     inline     >] print_address_description mm/kasan/report.c:197
 [<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286
 [<ffffffff817e5705>] kasan_report+0x35/0x40 mm/kasan/report.c:306
 [<     inline     >] check_memory_region_inline mm/kasan/kasan.c:308
 [<ffffffff817e3fb9>] check_memory_region+0x139/0x190 mm/kasan/kasan.c:315
 [<ffffffff817e4044>] kasan_check_write+0x14/0x20 mm/kasan/kasan.c:326
 [<     inline     >] copy_from_user arch/x86/include/asm/uaccess.h:689
 [<     inline     >] ep0_write drivers/usb/gadget/legacy/inode.c:1135
 [<ffffffff83228caf>] dev_config+0x86f/0x1190 drivers/usb/gadget/legacy/inode.c:1759
 [<ffffffff817fdd55>] __vfs_write+0x5d5/0x760 fs/read_write.c:510
 [<ffffffff817ff650>] vfs_write+0x170/0x4e0 fs/read_write.c:560
 [<     inline     >] SYSC_write fs/read_write.c:607
 [<ffffffff81803a5b>] SyS_write+0xfb/0x230 fs/read_write.c:599
 [<ffffffff84f47ec1>] entry_SYSCALL_64_fastpath+0x1f/0xc2

Indeed, there is a comment saying that the value of len is restricted
to a 16-bit integer, but the code doesn't actually do this.

This patch fixes the warning.  It replaces the comment with a
computation that forces the amount of data copied from the user in
ep0_write() to be no larger than the wLength size for the control
transfer, which is a 16-bit quantity.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When system try to close /dev/usb-ffs/adb/ep0 on one core, at the same
time another core try to attach new UDC, which will cause deadlock as
below scenario. Thus we should release ffs lock before issuing
unregister_gadget_item().

[   52.642225] c1 ======================================================
[   52.642228] c1 [ INFO: possible circular locking dependency detected ]
[   52.642236] c1 4.4.6+ #1 Tainted: G        W  O
[   52.642241] c1 -------------------------------------------------------
[   52.642245] c1 usb ffs open/2808 is trying to acquire lock:
[   52.642270] c0  (udc_lock){+.+.+.}, at: [<ffffffc00065aeec>]
		usb_gadget_unregister_driver+0x3c/0xc8
[   52.642272] c1  but task is already holding lock:
[   52.642283] c0  (ffs_lock){+.+.+.}, at: [<ffffffc00066b244>]
		ffs_data_clear+0x30/0x140
[   52.642285] c1 which lock already depends on the new lock.
[   52.642287] c1
               the existing dependency chain (in reverse order) is:
[   52.642295] c0
	       -> #1 (ffs_lock){+.+.+.}:
[   52.642307] c0        [<ffffffc00012340c>] __lock_acquire+0x20f0/0x2238
[   52.642314] c0        [<ffffffc000123b54>] lock_acquire+0xe4/0x298
[   52.642322] c0        [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc
[   52.642328] c0        [<ffffffc00066f7bc>] ffs_func_bind+0x504/0x6e8
[   52.642334] c0        [<ffffffc000654004>] usb_add_function+0x84/0x184
[   52.642340] c0        [<ffffffc000658ca4>] configfs_composite_bind+0x264/0x39c
[   52.642346] c0        [<ffffffc00065b348>] udc_bind_to_driver+0x58/0x11c
[   52.642352] c0        [<ffffffc00065b49c>] usb_udc_attach_driver+0x90/0xc8
[   52.642358] c0        [<ffffffc0006598e0>] gadget_dev_desc_UDC_store+0xd4/0x128
[   52.642369] c0        [<ffffffc0002c14e8>] configfs_write_file+0xd0/0x13c
[   52.642376] c0        [<ffffffc00023c054>] vfs_write+0xb8/0x214
[   52.642381] c0        [<ffffffc00023cad4>] SyS_write+0x54/0xb0
[   52.642388] c0        [<ffffffc000085ff0>] el0_svc_naked+0x24/0x28
[   52.642395] c0
              -> #0 (udc_lock){+.+.+.}:
[   52.642401] c0        [<ffffffc00011e3d0>] print_circular_bug+0x84/0x2e4
[   52.642407] c0        [<ffffffc000123454>] __lock_acquire+0x2138/0x2238
[   52.642412] c0        [<ffffffc000123b54>] lock_acquire+0xe4/0x298
[   52.642420] c0        [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc
[   52.642427] c0        [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8
[   52.642432] c0        [<ffffffc00065995c>] unregister_gadget_item+0x28/0x44
[   52.642439] c0        [<ffffffc00066b34c>] ffs_data_clear+0x138/0x140
[   52.642444] c0        [<ffffffc00066b374>] ffs_data_reset+0x20/0x6c
[   52.642450] c0        [<ffffffc00066efd0>] ffs_data_closed+0xac/0x12c
[   52.642454] c0        [<ffffffc00066f070>] ffs_ep0_release+0x20/0x2c
[   52.642460] c0        [<ffffffc00023dbe4>] __fput+0xb0/0x1f4
[   52.642466] c0        [<ffffffc00023dd9c>] ____fput+0x20/0x2c
[   52.642473] c0        [<ffffffc0000ee944>] task_work_run+0xb4/0xe8
[   52.642482] c0        [<ffffffc0000cd45c>] do_exit+0x360/0xb9c
[   52.642487] c0        [<ffffffc0000cf228>] do_group_exit+0x4c/0xb0
[   52.642494] c0        [<ffffffc0000dd3c8>] get_signal+0x380/0x89c
[   52.642501] c0        [<ffffffc00008a8f0>] do_signal+0x154/0x518
[   52.642507] c0        [<ffffffc00008af00>] do_notify_resume+0x70/0x78
[   52.642512] c0        [<ffffffc000085ee8>] work_pending+0x1c/0x20
[   52.642514] c1
              other info that might help us debug this:
[   52.642517] c1  Possible unsafe locking scenario:
[   52.642518] c1        CPU0                    CPU1
[   52.642520] c1        ----                    ----
[   52.642525] c0   lock(ffs_lock);
[   52.642529] c0                                lock(udc_lock);
[   52.642533] c0                                lock(ffs_lock);
[   52.642537] c0   lock(udc_lock);
[   52.642539] c1
                      *** DEADLOCK ***
[   52.642543] c1 1 lock held by usb ffs open/2808:
[   52.642555] c0  #0:  (ffs_lock){+.+.+.}, at: [<ffffffc00066b244>]
		ffs_data_clear+0x30/0x140
[   52.642557] c1 stack backtrace:
[   52.642563] c1 CPU: 1 PID: 2808 Comm: usb ffs open Tainted: G
[   52.642565] c1 Hardware name: Spreadtrum SP9860g Board (DT)
[   52.642568] c1 Call trace:
[   52.642573] c1 [<ffffffc00008b430>] dump_backtrace+0x0/0x170
[   52.642577] c1 [<ffffffc00008b5c0>] show_stack+0x20/0x28
[   52.642583] c1 [<ffffffc000422694>] dump_stack+0xa8/0xe0
[   52.642587] c1 [<ffffffc00011e548>] print_circular_bug+0x1fc/0x2e4
[   52.642591] c1 [<ffffffc000123454>] __lock_acquire+0x2138/0x2238
[   52.642595] c1 [<ffffffc000123b54>] lock_acquire+0xe4/0x298
[   52.642599] c1 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc
[   52.642604] c1 [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8
[   52.642608] c1 [<ffffffc00065995c>] unregister_gadget_item+0x28/0x44
[   52.642613] c1 [<ffffffc00066b34c>] ffs_data_clear+0x138/0x140
[   52.642618] c1 [<ffffffc00066b374>] ffs_data_reset+0x20/0x6c
[   52.642621] c1 [<ffffffc00066efd0>] ffs_data_closed+0xac/0x12c
[   52.642625] c1 [<ffffffc00066f070>] ffs_ep0_release+0x20/0x2c
[   52.642629] c1 [<ffffffc00023dbe4>] __fput+0xb0/0x1f4
[   52.642633] c1 [<ffffffc00023dd9c>] ____fput+0x20/0x2c
[   52.642636] c1 [<ffffffc0000ee944>] task_work_run+0xb4/0xe8
[   52.642640] c1 [<ffffffc0000cd45c>] do_exit+0x360/0xb9c
[   52.642644] c1 [<ffffffc0000cf228>] do_group_exit+0x4c/0xb0
[   52.642647] c1 [<ffffffc0000dd3c8>] get_signal+0x380/0x89c
[   52.642651] c1 [<ffffffc00008a8f0>] do_signal+0x154/0x518
[   52.642656] c1 [<ffffffc00008af00>] do_notify_resume+0x70/0x78
[   52.642659] c1 [<ffffffc000085ee8>] work_pending+0x1c/0x20
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790

while dep->endpoint.desc is NULL.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Andrey Konovalov reported that we were not properly checking the upper
limit before of a device configuration size before calling
memdup_user(), which could cause some problems.

So set the upper limit to PAGE_SIZE * 4, which should be good enough for
all devices.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The stop_activity() routine in dummy-hcd is supposed to unlink all
active requests for every endpoint, among other things.  But it
doesn't handle ep0.  As a result, fuzz testing can generate a WARNING
like the following:

WARNING: CPU: 0 PID: 4410 at drivers/usb/gadget/udc/dummy_hcd.c:672 dummy_free_request+0x153/0x170
Modules linked in:
CPU: 0 PID: 4410 Comm: syz-executor Not tainted 4.9.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 ffff88006a64ed10 ffffffff81f96b8a ffffffff41b58ab3 1ffff1000d4c9d35
 ffffed000d4c9d2d ffff880065f8ac00 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 0000000041b58ab3 ffffffff859410e0 ffffffff813f0590
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [<ffffffff812b808f>] __warn+0x19f/0x1e0 kernel/panic.c:550
 [<ffffffff812b831c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585
 [<ffffffff830fcb13>] dummy_free_request+0x153/0x170 drivers/usb/gadget/udc/dummy_hcd.c:672
 [<ffffffff830ed1b0>] usb_ep_free_request+0xc0/0x420 drivers/usb/gadget/udc/core.c:195
 [<ffffffff83225031>] gadgetfs_unbind+0x131/0x190 drivers/usb/gadget/legacy/inode.c:1612
 [<ffffffff830ebd8f>] usb_gadget_remove_driver+0x10f/0x2b0 drivers/usb/gadget/udc/core.c:1228
 [<ffffffff830ec084>] usb_gadget_unregister_driver+0x154/0x240 drivers/usb/gadget/udc/core.c:1357

This patch fixes the problem by iterating over all the endpoints in
the driver's ep array instead of iterating over the gadget's ep_list,
which explicitly leaves out ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Reserved1 is documented as expected to be set to 0, but this test fails
when it it set to 0. Reverse the condition.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When FUNCTIONFS_EVENTFD flag is set, __ffs_data_got_descs reads a 32bits,
little-endian value right after the fixed structure header, and passes it
to eventfd_ctx_fdget. Document this.

Also, rephrase a comment to be affirmative about the role of string
descriptor at index 0. Ref: USB 2.0 spec paragraph "9.6.7 String", and
also checked to still be current in USB 3.0 spec paragraph "9.6.9 String".
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

By convention (according to doc) if function does not provide
get_alt() callback composite framework should assume that it has only
altsetting 0 and should respond with error if host tries to set
other one.

After commit dd4dff8b ("USB: composite: Fix bug: should test
set_alt function pointer before use it")
we started checking set_alt() callback instead of get_alt().
This check is useless as we check if set_alt() is set inside
usb_add_function() and fail if it's NULL.

Let's fix this check and move comment about why we check the get
method instead of set a little bit closer to prevent future false
fixes.

Fixes: dd4dff8b ("USB: composite: Fix bug: should test set_alt function pointer before use it")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb_get_dr_mode() expects the device-property to be spelled
"dr_mode" not "dr-mode".

Spelling it properly fixes the following warning showing up in dmesg:
[ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget

Signed-off-by: Hans de Goede <hdegoede@redhat.com
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Now that we're handling so many transfers at a time
and for some dwc3 revisions LPM events *must* be
enabled, we can fall into a situation where too many
events fire and we start receiving Overflow events.

Let's do what XHCI does and allocate a full page for
the Event Ring, this will avoid any future issues.

Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

commit 0416e494 ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.

Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.

Fixes: 0416e494 ("usb: dwc3: ep0: correct cache
	sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Let's call dwc3_ep0_prepare_one_trb() explicitly
because there are occasions where we will need more
than one TRB to handle an EP0 transfer.

A follow-up patch will fix one bug related to
multiple-TRB Data Phases when it comes to
mapping/unmapping requests for DMA.

Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit
c0bd5456 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")

Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The current default for gadget DMA descriptor results on bcm2835 in a
unnecessary error message:

  Invalid value 1 for param gadget-dma-desc

So fix this by using hw->dma_desc_enable as default value.

Fixes: dec4b556 ("usb: dwc2: gadget: Add descriptor DMA parameter")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The current defaults for DMA results on a non-DMA platform in a unnecessary
error message:

  Invalid value 0 for param gadget-dma

So fix this by using dma_capable as default value.

Fixes: 9962b62f ("usb: dwc2: Deprecate g-use-dma binding")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

According to the Devicetree ePAPR [1] the datatypes u8 and u16 are
not defined. So using device_property_read_u16() would result in
a partial read of a 32-bit big-endian integer which is not intended.
So we better read the complete 32-bit value. This fixes a regression
on bcm2835 where the values for g-rx-fifo-size and g-np-tx-fifo-size
always read as zero:

  Invalid value 0 for param g-rx-fifo-size
  Invalid value 0 for param g-np-tx-fifo-size

[1] - http://elinux.org/images/c/cf/Power_ePAPR_APPROVED_v1.1.pdf

Fixes: 05ee799f ("usb: dwc2: Move gadget settings into core_params")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since commit "usb: dwc2: Improve handling of host and device hwparams" the
host mode specific hardware parameter aren't initialized in peripheral mode
from the register settings anymore. So we better do not set them in this
case which avoids the following warnings on bcm2835:

  256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
  512 invalid for host_perio_tx_fifo_size. Check HW configuration.

Fixes: 55e1040e ("usb: dwc2: Improve handling of host and device hwparams")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull DAX updates from Dan Williams:
 "The completion of Jan's DAX work for 4.10.

  As I mentioned in the libnvdimm-for-4.10 pull request, these are some
  final fixes for the DAX dirty-cacheline-tracking invalidation work
  that was merged through the -mm, ext4, and xfs trees in -rc1. These
  patches were prepared prior to the merge window, but we waited for
  4.10-rc1 to have a stable merge base after all the prerequisites were
  merged.

  Quoting Jan on the overall changes in these patches:

     "So I'd like all these 6 patches to go for rc2. The first three
      patches fix invalidation of exceptional DAX entries (a bug which
      is there for a long time) - without these patches data loss can
      occur on power failure even though user called fsync(2). The other
      three patches change locking of DAX faults so that ->iomap_begin()
      is called in a more relaxed locking context and we are safe to
      start a transaction there for ext4"

  These have received a build success notification from the kbuild
  robot, and pass the latest libnvdimm unit tests. There have not been
  any -next releases since -rc1, so they have not appeared there"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  ext4: Simplify DAX fault path
  dax: Call ->iomap_begin without entry lock during dax fault
  dax: Finish fault completely when loading holes
  dax: Avoid page invalidation races and unnecessary radix tree traversals
  mm: Invalidate DAX radix tree entries only if appropriate
  ext2: Return BH_New buffers for zeroed blocks

Pull documentation fixes from Jonathan Corbet:
 "Two small fixes:

   - A merge error on my part broke the DocBook build. I've
     requisitioned one of tglx's frozen sharks for appropriate
     disciplinary action and resolved to be more careful about testing
     the DocBook stuff as long as it's still around.

   - Fix an error in unaligned-memory-access.txt"

* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
  Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
  docs: Fix build failure

Pull crypto fix from Herbert Xu:
 "This fixes a boot failure on some platforms when crypto self test is
  enabled along with the new acomp interface"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: testmgr - Use heap buffer for acomp test input

 mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
  mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
    return test_bit(PG_waiters);
         ^~~~~~~~

Fixes: b91e1302 ('mm: optimize PageWaiters bit use for unlock_page()')
Signed-off-by: Olof Johansson <olof@lixom.net>
Brown-paper-bag-by: Linus Torvalds <dummy@duh.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit 62906027 ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.

However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.

On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd.  The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.

On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result.  However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.

So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too.  And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.

This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.

The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit.  Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.

So this introduces the new architecture primitive

    clear_bit_unlock_is_negative_byte();

and adds the trivial implementation for x86.  We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better.  According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.

All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test".  After this, it's down to
0.66%, so just a quarter of the cost it used to be.

(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull crypto fix from Herbert Xu:
 "This fixes a hash corruption bug in the marvell driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: marvell - Copy IVDIG before launching partial DMA ahash requests

Pull networking fixes from David Miller:

 1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.

    The most important is to not assume the packet is RX just because
    the destination address matches that of the device. Such an
    assumption causes problems when an interface is put into loopback
    mode.

 2) If we retry when creating a new tc entry (because we dropped the
    RTNL mutex in order to load a module, for example) we end up with
    -EAGAIN and then loop trying to replay the request. But we didn't
    reset some state when looping back to the top like this, and if
    another thread meanwhile inserted the same tc entry we were trying
    to, we re-link it creating an enless loop in the tc chain. Fix from
    Daniel Borkmann.

 3) There are two different WRITE bits in the MDIO address register for
    the stmmac chip, depending upon the chip variant. Due to a bug we
    could set them both, fix from Hock Leong Kweh.

 4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: stmmac: fix incorrect bit set in gmac4 mdio addr register
  r8169: add support for RTL8168 series add-on card.
  net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
  openvswitch: upcall: Fix vlan handling.
  ipv4: Namespaceify tcp_tw_reuse knob
  net: korina: Fix NAPI versus resources freeing
  net, sched: fix soft lockup in tc_classify
  net/mlx4_en: Fix user prio field in XDP forward
  tipc: don't send FIN message from connectionless socket
  ipvlan: fix multicast processing
  ipvlan: fix various issues in ipvlan_process_multicast()

In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

The 80211.tmpl DocBook file was removed in commit 819bf593 ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit 7ddedebb ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:

*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.

cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Linux 4.10-rc1

Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 73b62bd0 ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit f23bc46c.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.

Fixes: 5108bbad ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christopher Covington reported a crash on aarch64 on recent Fedora
kernels:

kernel BUG at ./include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 752 Comm: cryptomgr_test Not tainted 4.9.0-11815-ge93b1cc8 #162
Hardware name: linux,dummy-virt (DT)
task: ffff80007c650080 task.stack: ffff800008910000
PC is at sg_init_one+0xa0/0xb8
LR is at sg_init_one+0x24/0xb8
...
[<ffff000008398db8>] sg_init_one+0xa0/0xb8
[<ffff000008350a44>] test_acomp+0x10c/0x438
[<ffff000008350e20>] alg_test_comp+0xb0/0x118
[<ffff00000834f28c>] alg_test+0x17c/0x2f0
[<ffff00000834c6a4>] cryptomgr_test+0x44/0x50
[<ffff0000080dac70>] kthread+0xf8/0x128
[<ffff000008082ec0>] ret_from_fork+0x10/0x50

The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org>
Fixes: d7db7a88 ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Now that dax_iomap_fault() calls ->iomap_begin() without entry lock, we
can use transaction starting in ext4_iomap_begin() and thus simplify
ext4_dax_fault(). It also provides us proper retries in case of ENOSPC.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>