When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the port_window support was verified it was done on setup where only
the MEM_TO_DEV direction was enabled. This got un-noticed and thus only
this direction worked.

Now that I have managed to get a setup to verify both direction it turned
out that the setup was incorrect:
omap_desc members are settings for the slave port while the omap_sg members
apply to the memory side of the sDMA setup.

Fixes: 527a2759 ("dmaengine: omap-dma: Fix the port_window support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: dmaengine@vger.kernel.org
Cc: dan.j.williams@intel.com
Cc: vinod.koul@intel.com
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If dma_request_slave_channel() failed to return a channel,
then the driver will print an error and request to defer probe,
regardless of the cause of the failure.
Defer if the DMA is not ready yet otherwise print an error.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing

Felipe writes:

usb: changes for v4.13 merge window

This time around we have a total of 57 non-merge commits. A list of
most important changes follows:

- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver

We want the USB fixes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.

This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.

Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.

One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications.  For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).

Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.

Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "Stream of fixes has slowed down, only a few this week:

   - Some DT fixes for Allwinner platforms, and addition of a clock to
     the R_CCU clock controller that had been missed.

   - A couple of small DT fixes for am335x-sl50"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
  ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
  ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
  ARM: dts: am335x-sl50: Fix card detect pin for mmc1
  arm64: allwinner: h5: Remove syslink to shared DTSI
  ARM: sunxi: h3/h5: fix the compatible of R_CCU

This patch adds a new function 'f_uac1'
(f_uac1 with virtual "ALSA card") that
uses recently created u_audio API. Comparing
to legacy f_uac1 function implementation it
doesn't require any real Audio codec to be
present on the device. In f_uac1 audio
streams are simply sinked to and sourced
from a virtual ALSA sound card created
using u_audio API.

Legacy f_uac1 approach is to write audio
samples directly to existing ALSA sound
card

f_uac1 approach is more generic/flexible
one - create an ALSA sound card that
represents USB Audio function and allows to
be used by userspace application that
may choose to do whatever it wants with the
data received from the USB Host and choose
to provide whatever it wants as audio data
to the USB Host.

f_uac1 also has capture support (gadget->host)
thanks to easy implementation via u_audio.
By default, capture interface has 48000kHz/2ch
configuration, same as playback channel has.

f_uac1 descriptors naming convention
uses f_uac2 driver naming convention that
makes it more common and meaningful.

Comparing to f_uac1_legacy, the f_uac1 doesn't
have volume/mute functionality. This is because
the f_uac1 volume/mute feature unit was dummy
implementation since that driver creation (2009)
and never had any real volume control or mute
functionality, so there is no any difference
here.

Since f_uac1 functionality, exposed
interface to userspace (virtual ALSA card),
input parameters are so different comparing
to f_uac1_legacy, that there is no any
reason to keep them in the same file/module,
and separate function was created.

g_audio can be built using one of existing
UAC functions (f_uac1, f_uac1_legacy or f_uac2)
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Before introducing new f_uac1 function (with virtual
ALSA card) make current implementation legacy.

This includes renaming of existing files, some
variables, config options and documentation
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Abstract the peripheral side ALSA sound card code from
the f_uac2 function into a component that can be called
by various functions, so the various flavors can be split
apart and selectively reused.

Visible changes:
 - add uac_params structure to pass audio paramteres for
   g_audio_setup
 - make ALSA sound card's name configurable
 - add [in/out]_ep_maxpsize
 - allocate snd_uac_chip structure during g_audio_setup
 - add u_audio_[start/stop]_[capture/playback] functions
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Simplify f_uac2 by removing platform driver/device
creation; use composite's usb_gadget device as
parent for sound card and for debug prints.
This removes extra layer of code without any functional
change.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

After commit 7e4da3fc ("usb: gadget: composite:
Test get_alt() presence instead of set_alt()") f_uac1
function became broken because it doesn't have
get_alt() callback implementation and composite
framework never set altsetting 1 for audiostreaming
interface. On host site it looks like:

 [424339.017711] 21:1:1: usb_set_interface failed (-32)

Since host can't set altsetting 1, it can't start
playing audio.

In order to fix it implemented get_alt along with
minor improvements (error conditions checking)
similar to what existing f_uac2 has.

Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

commit 46ddd79e ("usb: gadget: udc: atmel: Remove AVR32 bits from the
driver") left the accessor macros introduced by commit a3dd3bef ("usb:
gadget: atmel_usba: use endian agnostic IO on ARM"). They can now be
removed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Corrected the register to check the 64-bit pointer
capability state. 64-bit pointer implementation capability
was checking in wrong register, which causes the BDC
enumeration failure in 64-bit memory address.

Fixes: efed421a ("usb: gadget: Add UDC driver for
Broadcom USB3.0 device controller IP BDC")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Merge tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes

Allwinner fixes for 4.12

A few fixes around the PRCM support that got in 4.12 with a wrong
compatible, and a missing clock in the binding.

* tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
  ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
  arm64: allwinner: h5: Remove syslink to shared DTSI
  ARM: sunxi: h3/h5: fix the compatible of R_CCU
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.12/fixes-sl50' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Two fixes for am335x-sl50 to fix a boot time error
for claiming SPI pins, and to fix a SDIO card detect
pin for production version of the device.

* tag 'omap-for-v4.12/fixes-sl50' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
  ARM: dts: am335x-sl50: Fix card detect pin for mmc1
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull virtio bugfix from Michael Tsirkin:
 "It turns out balloon does not handle IOMMUs correctly. We should fix
  that at some point, for now let's just disable this configuration"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_balloon: disable VIOMMU support

Pull i2c fixes from Wolfram Sang:
 "Two driver bugfixes"

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: ismt: fix wrong device address when unmap the data buffer
  i2c: rcar: use correct length when unmapping DMA

Pull MIPS fixes from Ralf Baechle:

 - Three highmem fixes:
    + Fixed mapping initialization
    + Adjust the pkmap location
    + Ensure we use at most one page for PTEs

 - Fix makefile dependencies for .its targets to depend on vmlinux

 - Fix reversed condition in BNEZC and JIALC software branch emulation

 - Only flush initialized flush_insn_slot to avoid NULL pointer
   dereference

 - perf: Remove incorrect odd/even counter handling for I6400

 - ftrace: Fix init functions tracing

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: .its targets depend on vmlinux
  MIPS: Fix bnezc/jialc return address calculation
  MIPS: kprobes: flush_insn_slot should flush only if probe initialised
  MIPS: ftrace: fix init functions tracing
  MIPS: mm: adjust PKMAP location
  MIPS: highmem: ensure that we don't use more than one page for PTEs
  MIPS: mm: fixed mappings: correct initialisation
  MIPS: perf: Remove incorrect odd/even counter handling for I6400

virtio balloon bypasses the DMA API entirely so does not support the
VIOMMU right now.  It's not clear we need that support, for now let's
just make sure we don't pretend to support it.

Cc: stable@vger.kernel.org
Cc: Wei Wang <wei.w.wang@intel.com>
Fixes: 1a937693 ("virtio: new feature to detect IOMMU device quirk")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Pull x86 fixes from Thomas Gleixner:
 "Two fixlets for x86:

   - Handle WARN_ONs proper with the new UD based WARN implementation

   - Disable 1G mappings when 2M mappings are disabled by kmemleak or
     debug_pagealloc. Otherwise 1G mappings might still be used,
     confusing the debug mechanisms"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Disable 1GB direct mappings when disabling 2MB mappings
  x86/debug: Handle early WARN_ONs proper

Pull timer fixes from Thomas Gleixner:
 "Three fixlets for timers:

   - Two hot-fixes for the alarmtimer based posix timers, which prevent
     a nasty DOS by self rescheduling timers. The proper cleanup of that
     mess is queued for 4.13

   - Make a function static"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Make tick_broadcast_setup_oneshot() static
  alarmtimer: Rate limit periodic intervals
  alarmtimer: Prevent overflow of relative timers

Pull scheduler fixes from Thomas Gleixner:
 "Two small fixes for the schedulre core:

   - Use the proper switch_mm() variant in idle_task_exit() because that
     code is not called with interrupts disabled.

   - Fix a confusing typo in a printk"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()
  sched/fair: Fix typo in printk message

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the perf user space side:

   - Fix the probing of precise_ip level, which got broken recently for
     x86.

   - Unbreak the ARCH=x86_64 build

   - Report module before trying to unwind into the module code, which
     avoids broken stack frames displayed"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf unwind: Report module before querying isactivation in dwfl unwind
  perf tools: Fix build with ARCH=x86_64
  perf evsel: Fix probing of precise_ip level for default cycles event

Pull irq fix from Thomas Gleixner:
 "Add a missing resource release to an error path"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Release resources in __setup_irq() error path

Pull objtool fix from Thomas Gleixner:
 "A single fix which adds fortify_panic to the list of no return
  functions"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Add fortify_panic as __noreturn function

Merge tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:
 "Two LED fixes:

   - fix signal source assignment for leds-bcm6328

   - revert patch that intended to fix LED behavior on suspend but it
     had a side effect preventing suspend at all due to uevent being
     sent on trigger removal"

* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  Revert "leds: handle suspend/resume in heartbeat trigger"
  leds: bcm6328: fix signal source assignment for leds 4 to 7

Pull USB fixes from Greg KH:
 "Here are some small gadget and xhci USB fixes for 4.12-rc6.

  Nothing major, but one of the gadget patches does fix a reported oops,
  and the xhci ones resolve reported problems. All have been in
  linux-next with no reported issues"

* tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
  usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
  usb: xhci: Fix USB 3.1 supported protocol parsing
  USB: gadget: fix GPF in gadgetfs
  usb: gadget: composite: make sure to reactivate function on unbind

Pull staging and IIO fixes from Greg KH:
 "Here are some small staging and IIO driver fixes for 4.12-rc6.

  Nothing huge, just a few small driver fixes for reported issues. All
  have been in linux-next with no reported issues"

* tag 'staging-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Staging: rtl8723bs: fix an error code in isFileReadable()
  iio: buffer-dmaengine: Add missing header buffer_impl.h
  iio: buffer-dma: Add missing header buffer_impl.h
  iio: adc: meson-saradc: fix potential crash in meson_sar_adc_clear_fifo
  iio: adc: mxs-lradc: Fix return value check in mxs_lradc_adc_probe()
  iio: imu: inv_mpu6050: add accel lpf setting for chip >= MPU6500
  staging: iio: ad7152: Fix deadlock in ad7152_write_raw_samp_freq()

Pull ceph fixes from Ilya Dryomov:
 "A fix for an old ceph ->fh_to_* bug from Luis and two timestamp fixups
  from Zheng, prompted by the ongoing y2038 work"

* tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client:
  ceph: unify inode i_ctime update
  ceph: use current_kernel_time() to get request time stamp
  ceph: check i_nlink while converting a file handle to dentry

Pull xfs fix from Darrick Wong:
 "One more bugfix for you for 4.12-rc6 to fix something that came up in
  an earlier rc:

   - Fix some bogus ASSERT failures on CONFIG_SMP=n and CONFIG_XFS_DEBUG=y"

* tag 'xfs-4.12-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix spurious spin_is_locked() assert failures on non-smp kernels

Pull ufs fixes from Al Viro:
 "Fix assorted ufs bugs: a couple of deadlocks, fs corruption in
  truncate(), oopsen on tail unpacking and truncate when racing with
  vmscan, mild fs corruption (free blocks stats summary buggered, *BSD
  fsck would complain and fix), several instances of broken logics
  around reserved blocks (starting with "check almost never triggers
  when it should" and then there are issues with sufficiently large
  UFS2)"

[ Note: ufs hasn't gotten any loving in a long time, because nobody
  really seems to use it. These ufs fixes are triggered by people
  actually caring now, not some sudden influx of new bugs.  - Linus ]

* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ufs_truncate_blocks(): fix the case when size is in the last direct block
  ufs: more deadlock prevention on tail unpacking
  ufs: avoid grabbing ->truncate_mutex if possible
  ufs_get_locked_page(): make sure we have buffer_heads
  ufs: fix s_size/s_dsize users
  ufs: fix reserved blocks check
  ufs: make ufs_freespace() return signed
  ufs: fix logics in "ufs: make fsck -f happy"

Pull vfs fixes from Al Viro:
 "A couple of fixes; a leak in mntns_install() caught by Andrei (this
  cycle regression) + d_invalidate() softlockup fix - that had been
  reported by a bunch of people lately, but the problem is pretty old"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: don't forget to put old mntns in mntns_install
  Hang/soft lockup in d_invalidate with simultaneous calls

Pull PCI fixes from Bjorn Helgaas:

 - fix another PCI_ENDPOINT build error (merged for v4.12)

 - fix error codes added to config accessors for v4.12

* tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: endpoint: Select CRC32 to fix test build error
  PCI: Make error code types consistent in pci_{read,write}_config_*

Pull fbdev fixes from Bartlomiej Zolnierkiewicz:

 - fix udlfb driver to stop spamming logs (Mike Gerow)

 - add missing endianness conversions in smscufx & udlfb drivers (Johan
   Hovold)

 - fix few gcc warnings/errors (Arnd Bergmann)

* tag 'fbdev-v4.12-rc6' of git://github.com/bzolnier/linux:
  video: fbdev: udlfb: drop log level for blanking
  video: fbdev: via: remove possibly unused variables
  video: fbdev: add missing USB-descriptor endianness conversions
  video: fbdev: avoid int-in-bool-context warning

Merge misc fixes from Andrew Morton:
 "5 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: correct the comment when reclaimed pages exceed the scanned pages
  userfaultfd: shmem: handle coredumping in handle_userfault()
  mm: numa: avoid waiting on freed migrated pages
  swap: cond_resched in swap_cgroup_prepare()
  mm/memory-failure.c: use compound_head() flags for huge pages

Commit e1587a49 ("mm: vmpressure: fix sending wrong events on
underflow") declared that reclaimed pages exceed the scanned pages due
to the thp reclaim.

That is incorrect because THP will be spilt to normal page and loop
again, which will result in the scanned pages increment.

[akpm@linux-foundation.org: tweak comment text]
Link: http://lkml.kernel.org/r/1496824266-25235-1-git-send-email-zhongjiang@huawei.comSigned-off-by: zhongjiang <zhongjiang@huawei.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Anon and hugetlbfs handle FOLL_DUMP set by get_dump_page() internally to
__get_user_pages().

shmem as opposed has no special FOLL_DUMP handling there so
handle_mm_fault() is invoked without mmap_sem and ends up calling
handle_userfault() that isn't expecting to be invoked without mmap_sem
held.

This makes handle_userfault() fail immediately if invoked through
shmem_vm_ops->fault during coredumping and solves the problem.

The side effect is a BUG_ON with no lock held triggered by the
coredumping process which exits.  Only 4.11 is affected, pre-4.11 anon
memory holes are skipped in __get_user_pages by checking FOLL_DUMP
explicitly against empty pagetables (mm/gup.c:no_page_table()).

It's zero cost as we already had a check for current->flags to prevent
futex to trigger userfaults during exit (PF_EXITING).

Link: http://lkml.kernel.org/r/20170615214838.27429-1-aarcange@redhat.comSigned-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: <stable@vger.kernel.org>	[4.11+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>