Skip to content

L
linux
Switch branch/tag
  1. 03 Dec, 2006 10 commits
    • Tejun Heo's avatar
      [PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze() · 0f0a3ad3
      Tejun Heo authored 
      Now that BMDMA status is recorded in irq handler.  ata_bmdma_freeze()
is free to manipulate host status.  Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.

This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port.  This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it.  The removed code was
SFF-specific and was in the wrong place.

Note that ->freeze() handler is always called under ap->lock held and
irq disabled.  Even if CTL manipulation causes stuck IRQ, it's cleared
immediately.  This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      0f0a3ad3
    • Tejun Heo's avatar
      [PATCH] libata: move BMDMA host status recording from EH to interrupt handler · ea54763f
      Tejun Heo authored 
      For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr).  Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user.  Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      ea54763f
    • Tejun Heo's avatar
      [PATCH] libata: make sure sdev doesn't go away while rescanning · f84e7e41
      Tejun Heo authored 
      ata_scsi_dev_rescan() doesn't synchronize against SCSI device detach
and the target sdev might go away in the middle.  Fix it.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      f84e7e41
    • Tejun Heo's avatar
      [PATCH] libata: don't request sense if the port is frozen · a569a30d
      Tejun Heo authored 
      If EH command is issued to a frozen port, it fails with AC_ERR_SYSTEM.
libata used to request sense even when the port is frozen needlessly
adding AC_ERR_SYSTEM to err_mask.  Don't do it.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      a569a30d
    • Tejun Heo's avatar
      [PATCH] libata: fix READ CAPACITY simulation · 6a36261e
      Tejun Heo authored 
      * READ CAPACITY (16) implementation fixed.  Result was shifted by two
  bytes.  Carlos Pardo spotted this problem and submitted preliminary
  patch.  Capacity => 2TB is handled correctly now.  (verifid w/ fake
  capacity)

* Use dev->n_sectors instead of re-reading directly from ID data.

* Define and use ATA_SCSI_RBUF_SET() which considers rbuf length.
  This should be done for all simulation functions.  Userland can
  issue any simulated command with arbitrary buffer length.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
      6a36261e
    • Tejun Heo's avatar
      [PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2 · 3d3cca37
      Tejun Heo authored 
      This patch implements ATA_FLAG_SETXFER_POLLING and use in pata_via.
If this flag is set, transfer mode setting performed by polling not by
interrupt.  This should help those controllers which raise interrupt
before the command is actually complete on SETXFER.

Rationale for this approach.

* uses existing facility and relatively simple
* no busy sleep in the interrupt handler
* updating drivers is easy

While at it, kill now unused flag ATA_FLAG_SRST in pata_via.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      3d3cca37
    • Tejun Heo's avatar
      [PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs · 8070217d
      Tejun Heo authored 
      There are machines out there which share legacy PCI IDE IRQs w/ other
devices.  libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode.  Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.

Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable.  Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      8070217d
    • Tejun Heo's avatar
      [PATCH] libata: remove unused HSM_ST_UNKNOWN · 582982e6
      Tejun Heo authored 
      HSM_ST_UNKNOWN is not used anywhere.  Its value is zero and supposed
to serve sanity check purpose but HSM_ST_IDLE is used for that
purpose.  This unused state causes confusion.  After a port is
initialized but before the first command is executed, the idle hsm
state is UNKNOWN.  However, once a command has completed, the idle hsm
state is IDLE.  This defeats sanity check in ata_pio_task() for the
first command.

This patch removes HSM_ST_UNKNOWN and consequently make HSM_ST_IDLE
the default state.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      582982e6
    • Tejun Heo's avatar
      [PATCH] libata: kill unnecessary sht->max_sectors initializations · 2eab80ac
      Tejun Heo authored 
      sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      2eab80ac
    • Tejun Heo's avatar
      [PATCH] libata: add missing sht->slave_destroy · c972b60b
      Tejun Heo authored 
      Add missing sht->slave_destroy.  Most drivers received this fix in
didn't.  Fix those four drives.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      c972b60b
  3. 02 Dec, 2006 30 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7