The GPU found on NVIDIA Tegra194 SoCs is a Volta generation GPU called
GV11B.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

On Tegra194, data on valid operating points for the CPUs needs to be
queried from BPMP. However, there is no node representing CPU complex.
So, add a compatible string to the 'cpus' node instead of using dummy
node to bind the cpufreq driver to. Also, add reference to the BPMP
instance for the CPU complex.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The SOR controller needs the AVDD I/O and VDD HDMI PLL supplies in order
to operate correctly. Make sure to specify them for the Norrin board.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The VI I2C controller provides an I2C bus and therefore needs to define
the #address-cells and #size-cells properties.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra210 VI I2C is in VE power domain and i2c-vi node should have
power-domains property.

Current Tegra210 i2c-vi device node is missing both VI I2C clocks
and power-domains property.

This patch adds them.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The ISP blocks take a clock and a reset as inputs, so add those to the
device tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Tegra210 DPAUX controller is not compatible with that found on
Tegra124, so it must have a separate compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DPAUX controller device tree bindings require the bus to have an
i2c-bus subnode to distinguish between I2C clients and pinmux groups.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Most device tree files already do this, so update the remaining ones
for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Remove tabs in places where they don't belong (i.e. where a single space
is sufficient).
Signed-off-by: Thierry Reding <treding@nvidia.com>

The VBUS for USB3 connector on the Jetson TX2 is connected to the
vdd_usb1 supply and although this is populated for the USB2 port
on the USB3 connector it is not populated for the USB3 port and
causes the following warning to be seen on boot ...

 usb3-0: supply vbus not found, using dummy regulator

Fix this by also adding the VBUS supply to the USB3 port.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Populate the DFLL node and corresponding PWM pin nodes in order to
enable CPUFREQ support on the Jetson Nano platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add the device-tree source files for the Tegra194 Jetson Xavier NX
Developer Kit. The Xavier NX Developer Kit consists of a small form
factor system-on-module (SOM) board (part number p3668-0000) and a
carrier board (part number p3509-0000).

The Xavier NX Developer Kit SOM features a micro-SD card slot, however,
there is also a variant of the SOM available that features a 16GB eMMC.
Given that the carrier board can be used with the different SOM
variants, that have different part numbers, both the compatible string
and file name of the device-tree source file for the Developer Kit is a
concatenation of the SOM and carrier board part numbers.

Based on some initial work by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Re-order Tegra194's PCIe aperture mappings to have IO window moved to
64-bit aperture and have the entire 32-bit aperture used for accessing
the configuration space. This makes it to use the entire 32MB of the 32-bit
aperture for ECAM purpose while booting through ACPI.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This patch enables VI and CSI in device tree for Jetson Nano.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Jetson TX1 development board has a camera expansion connector which
has 2V8, 1V8 and 1V2 supplies to power up the camera sensor on the
supported camera modules.

Camera module designed as per Jetson TX1 camera expansion connector
may use these supplies for camera sensor avdd 2V8, digital core 1V8,
and digital interface 1V2 voltages.

These supplies are from fixed regulators on TX1 carrier board with
enable control signals from I2C GPIO expanders.

This patch adds these camera supplies to Jetson TX1 device tree to
allow using these when a camera module is used.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This is purely to make the json-schema validation tools happy because
they cannot deal with string arrays that may be in arbitrary order.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The control backbone is a simple-bus and hence its device tree node
should be named "bus@<unit-address>" according to the bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Move the usb@700d0000 node to the correct place in the device tree,
ordered by unit-address.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Standardize on "pmic" as the node name for the PMIC on Tegra210 systems
and use consistent names for pinmux and GPIO hog nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Device tree nodes for interrupt controllers should be named "interrupt-
controller", so rename the AGIC accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Properly indent subsequent lines so that they align with the first line.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Properly indent subsequent lines so that they align with the first line.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The AON GPIO controller on Tegra194 currently only uses a single
interrupt, so remove the extra ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>

SRAM nodes should be named sram@<unit-address> to match the bindings.

While at it, also remove the unneeded, custom compatible string for
SRAM partition nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The display hub on Tegra186 and Tegra194 is not a simple bus, so drop
the corresponding compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

It's very difficult to describe string lists that can be in arbitrary
order using the json-schema based validation tooling. Since the OS is
not going to care either way, take the easy way out and reorder these
entries to match the order defined in the bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The XUSB controller doesn't need the XUSB pad controller's interrupt, so
remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The address-bits and page-size properties that are currently used are
not valid properties according to the bindings. Use the address-width
and pagesize properties instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use the preferred {id,vbus}-gpios over the {id,vbus}-gpio properties and
fix the ordering of compatible strings (most-specific ones should come
first).
Signed-off-by: Thierry Reding <treding@nvidia.com>

On Tegra186 and later, the BPMP is responsible for enabling/disabling
the PCIe related power supplies of the pad controller and there is no
need for the operating system to control them, so they can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>

USB PHYs must have a #phy-cells property, so add one to the Tegra USB
PHYs which don't have one.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The external memory controller found on Tegra132 is not fully compatible
with the instantiation on Tegra124, so remove the corresponding string
from the list of compatible strings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The sor0_out clock is required to make eDP work properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The host1x is not a simple bus, so drop the corresponding compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tuple boundaries should be marked by < and > to make it clear which
cells are part of the same tuple. This also helps the json-schema based
validation tooling to properly parse this data.

While at it, also remove the "immovable" bit from PCI addresses. All of
these addresses are in fact "movable".
Signed-off-by: Thierry Reding <treding@nvidia.com>

This panel supply is always on, so this does happen to work by accident.
Make sure to properly hook up the power supply to model the dependency
correctly and so that the panel continues to operate properly even if
the supply is not always on.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard way to do this is to list out the regulators at the top-
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>

battery-name is not a documented property, so drop it to avoid
validation failures.
Signed-off-by: Thierry Reding <treding@nvidia.com>