Catching up with the stack here and implement CCA ED level setting.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Catching up with the stack here and implement CSMA parameter setting.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

hci_vhci driver creates a hci device object dynamically upon each
HCI_VENDOR_PKT write.  Although it checks the already created object
and returns an error, it's still racy and may build multiple hci_dev
objects concurrently when parallel writes are performed, as the device
tracks only a single hci_dev object.

This patch introduces a mutex to protect against the concurrent device
creations.

Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

I expierenced when setting channel while sleep mode it didn't changed
the channel inside the hardware registers. Then I got another report of
an user which has similar issues.

I increased the sleep to off state change timing, which is according
at86rf233 at maximum 1000 us. After this change I got no similar effects
again.

I tried another option to wait on AWAKE_END irq, which can be used to
wait until the transceiver is awaked. I tested it and the IRQ took 4
seconds after starting state change. I don't believe it takes 4 seconds
to go into the TRX_OFF state from SLEEP state. The alternative is to
increase the timings which seems to work.

Cc: Oleg Hahm <oliver.hahm@inria.fr>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In case of link-layer specific handling for 802.15.4 we need to cast to
802.15.4 sepcific structures. Simple add this header when include the
6lowpan header.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds the lowpan_is_ll function, which can be used to make a
special 6lowpan linklayer handling for a specific 6lowpan linklayer
type.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This function will be use in later functionality in other branches than
generic 6lowpan, so we move it to the global 6lowpan header.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes unnecessary zero data for a stack variable.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a lowpan prefix to each functions which doesn't have
such prefix currently.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch moves the 802.15.4 link layer specific structures to generic
6lowpan. This is necessary for special 802.15.4 6lowpan handling in
6lowpan generic layer.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch changes the naming for interface private data for lowpan
intefaces. The current private data scheme is:

-------------------------------------------------
|    6LoWPAN Generic   |    LinkLayer 6LoWPAN   |
-------------------------------------------------

the current naming schemes are:

- 6LoWPAN Generic:
  - lowpan_priv
- LinkLayer 6LoWPAN:
  - BTLE
    - lowpan_dev
  - 802.15.4:
    - lowpan_dev_info

the new naming scheme with this patch will be:

- 6LoWPAN Generic:
  - lowpan_dev
- LinkLayer 6LoWPAN:
  - BTLE
    - lowpan_btle_dev
  - 802.15.4:
    - lowpan_802154_dev
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The short address is unique in combination with the panid. This patch
will add the panid for generating an ieee802154 address hash.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The generation of autoconfigured IPv6 link-local addresses starts with a
notification on interface up.

To handle autoconfiguration according to RFC 4944 requires pan id and
short address to generate an autoconfigured link-local address. This
patch will avoid changing of these link-layer address configuration
while lowpan interface is up.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduce some short address handling functionality into
ieee802154 headers.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes some const from non-pointer types and fixes the
function name for the ieee802154_is_valid_extended_unicast_addr
comment.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We set the TXNSECEN bit of register TXNCON to on when transmitting a
security-enabled frame, as described in section 3.12.2 of the MRF
datasheet.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Alexandre Macabies <web+oss@zopieux.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When receiving a security-enabled IEEE 802.15.4 frame, the MRF24J40
triggers a SECIF interrupt that needs to be handled for RX processing
to keep functioning properly.

This patch enables the SECIF interrupt and makes the MRF ignores all
hardware processing of security-enabled frames, that is handled by the
ieee802154 stack instead.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Alexandre Macabies <web+oss@zopieux.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

ieee802154_is_secen checks if the 802.15.4 security bit is set in the
frame control field.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Alexandre Macabies <web+oss@zopieux.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

John Crispin says:

====================
net: mediatek: make the driver pass stress tests

While testing the driver we managed to get the TX path to stall and fail
to recover. When dual MAC support was added to the driver, the whole queue
stop/wake code was not properly adapted. There was also a regression in the
locking of the xmit function. The fact that watchdog_timeo was not set and
that the tx_timeout code failed to properly reset the dma, irq and queue
just made the mess complete.

This series make the driver pass stress testing. With this series applied
the testbed has been running for several days and still has not locked up.
We have a second setup that has a small hack patch applied to randomly stop
irqs and/or one of the queues and successfully manages to recover from these
simulated tx stalls.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The QID field gets set to the mac id. This made the DMA linked list queue
the traffic of each MAC on a different internal queue. However during long
term testing we found that this will cause traffic stalls as the multi
queue setup requires a more complete initialisation which is not part of
the upstream driver yet.

This patch removes the code setting the QID field, resulting in all
traffic ending up in queue 0 which works without any special setup.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The worker always touches both netdevs. It is ethernet core and not MAC
specific. We only need one worker, which belongs into the ethernets core
struct.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver supports 2 MACs. Both run on the same DMA ring. If we hit a TX
timeout we need to stop both netdevs before restarting them again. If we
don't do this, mtk_stop() wont shutdown DMA and the consecutive call to
mtk_open() wont restart DMA and enable IRQs.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inside the TX path there is a lock inside the tx_map function. This is
however too late. The patch moves the lock to the start of the xmit
function right before the free count check of the DMA ring happens.
If we do not do this, the code becomes racy leading to TX stalls and
dropped packets. This happens as there are 2 netdevs running on the
same physical DMA ring.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver supports 2 MACs. Both run on the same DMA ring. If we go
above/below the TX rings threshold value, we always need to wake/stop
the queue of both devices. Not doing to can cause TX stalls and packet
drops on one of the devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW reset is triggered in the mtk_hw_init() function. There is no need to
also reset the core during probe.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code used to also support the PDMA engine, which had 2 packet pointers
per descriptor. Because of this we had to divide the result by 2 and round
it up. This is no longer needed as the code only supports QDMA.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original commit failed to set watchdog_timeo. This patch sets
watchdog_timeo to HZ.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains the first batch of Netfilter updates for
your net-next tree.

1) Define pr_fmt() in nf_conntrack, from Weongyo Jeong.

2) Define and register netfilter's afinfo for the bridge family,
   this comes in preparation for native nfqueue's bridge for nft,
   from Stephane Bryant.

3) Add new attributes to store layer 2 and VLAN headers to nfqueue,
   also from Stephane Bryant.

4) Parse new NFQA_VLAN and NFQA_L2HDR nfqueue netlink attributes
   coming from userspace, from Stephane Bryant.

5) Use net->ipv6.devconf_all->hop_limit instead of hardcoded hop_limit
   in IPv6 SYNPROXY, from Liping Zhang.

6) Remove unnecessary check for dst == NULL in nf_reject_ipv6,
   from Haishuang Yan.

7) Deinline ctnetlink event report functions, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Not performance critical, it is only invoked when an expectation is
added/destroyed.

While at it, kill unused nf_ct_expect_event() wrapper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Way too large; move it to nf_conntrack_ecache.c.
Reduces total object size by 1216 byte on my machine.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2016-04-12

Here's a set of Bluetooth & 802.15.4 patches intended for the 4.7 kernel:

 - Fix for race condition in vhci driver
 - Memory leak fix for ieee802154/adf7242 driver
 - Improvements to deal with single-mode (LE-only) Bluetooth controllers
 - Fix for allowing the BT_SECURITY_FIPS security level
 - New BCM2E71 ACPI ID
 - NULL pointer dereference fix fox hci_ldisc driver

Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MDIO devices can be stacked upon each other. The current code supports
two levels, which until recently has been enough for a DSA mdio bus on
top of another bus. Now we have hardware which has an MDIO mux in the
middle.

Define an MDIO MUTEX class with three levels.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
RxRPC: 2nd rewrite part 1

Okay, I'm in the process of rewriting the RxRPC rewrite.  The primary aim of
this second rewrite is to strictly control the number of active connections we
know about and to get rid of connections we don't need much more quickly.

On top of this, there are fixes to the protocol handling which will all occur
in later parts.

Here's the first set of patches from the second go, aimed at net-next.  These
are all fixes and cleanups preparatory to the main event.

Notable parts of this set include:

 (1) A fix for the AFS filesystem to wait for outstanding calls to complete
     before closing the RxRPC socket.

 (2) Differentiation of local and remote abort codes.  At a future point
     userspace will get to see this via control message data on recvmsg().

 (3) Absorb the rxkad module into the af_rxrpc module to prevent a dependency
     loop.

 (4) Create a null security module and unconditionalise calls into the
     security module that's in force (there will always be a security module
     applied to a connection, even if it's just the null one).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a null security type for security index 0 and get rid of all
conditional calls to the security operations.  We expect normally to be
using security, so this should be of little negative impact.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Absorb the rxkad security module into the af_rxrpc module so that there's
only one module file.  This avoids a circular dependency whereby rxkad pins
af_rxrpc and cached connections pin rxkad but can't be manually evicted
(they will expire eventually and cease pinning).

With this change, af_rxrpc can just be unloaded, despite having cached
connections.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't assume transport address family and size when using the peer address
to send a packet.  Instead, use the start of the transport address rather
than any particular element of the union and use the transport address
length noted inside the sockaddr_rxrpc struct.

This will be necessary when IPv6 support is introduced.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't pass gfp around in incoming call handling functions, but rather hard
code it at the points where we actually need it since the value comes from
within the rxrpc driver and is always the same.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the rxrpc_connection and rxrpc_call structs, there's one field to hold
the abort code, no matter whether that value was generated locally to be
sent or was received from the peer via an abort packet.

Split the abort code fields in two for cleanliness sake and add an error
field to hold the Linux error number to the rxrpc_call struct too
(sometimes this is generated in a context where we can't return it to
userspace directly).

Furthermore, add a skb mark to indicate a packet that caused a local abort
to be generated so that recvmsg() can pick up the correct abort code.  A
future addition will need to be to indicate to userspace the difference
between aborts via a control message.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static arrays of strings should be const char *const[].
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move some miscellaneous bits out into their own file to make it easier to
split the call handling.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>